Qos-ip-list Qos-ip-list-group | Hitachi GR2000 Series manual

Filtering/QoS Information

information to be collated into a single group. Finally, IP QoS (qos-ip) applies the group used on each interface.

1.2.5qos-ip-list

1.2.6qos-ip-list-group

	1.2.8 qos-ip
Flow Control (input)			Flow Control (output)		Queue Control
						Transmission Control
		Route Search
Flow Detection	Priority Determination		Flow Detection	Priority Determination
	TOS Rewrite			TOS Rewrite
	Contracted Bandwidth			Contracted Bandwidth		Interface
	Monitoring			Monitoring		(LINE,DLCI, etc.)

Flow Detection

List n

List 2

List 1

Priority Determination

TOS Rewrite

Contracted Bandwidth Monitoring

			Group 2
		Group 1
	Definition		List No.
	Definition		List No.
			List No.
	Regist		2
	1		1
			7
	2		2

4

34

5

46

Sets from qos-ip.

:Control range of this command

Sets from qos-ip-list.

Sets from qos-ip-list-group.

Figure 1-7 Range of QoS IP Frame Condition Information, QoS IP Frame Condition Group Information, and IP QoS Information Control

5.TOS-QoS conversion table for priority determination

This table determines the priority of incoming IP packets detected by flow control using either the packets’ TOS values or rewritten TOS values. The TOS-QoS conversion table (qos-tos-map) command determines priority for each TOS field precedence.

GR2K-GA-0014	1-133
Ver. 07-02

Image 175

Hitachi GR2000 Series manual Qos-ip-list Qos-ip-list-group, GR2K-GA-0014 133 Ver

Contents

GR2K-GA-0014 Ver Hitachi Gigabit Router GR2000 Series Enhanced Version Ver GR2K-GA-0014 Release 06-05 DecemberChange Record Preface Title Description/Notes Part Number GR2000 Gigabit Router Series Documentation GR2K-GA-0014 Ver Abbreviations Carrier Sense Multiple Access with Collision Detection Boot Strap RouterCommon Open Policy Service CoS Class of Service Frame Check Sequence Guaranteed Frame RateIntegrated Services Digital Network Internet Service Provider Viii GR2K-GA-0014 Ver Protocol Independent Multicast-Sparse Mode Network Service Access PointOperation Administration and Management Protocol Independent Multicast-Dense Mode Service Advertising Protocol Product Support ServiceQoS Quality of Service Router Advertisement Service Access Point Weighted Fair Queueing Switch to Switch ProtocolSwitched Virtual Channel Connection Type Of Service Xii Acknowledgments Xiii Bsdi Internet Server Xiv AT&T David M. GAY INFO-ZIP Group Xvi SUN MICROSYSTEMS, INC Wildboar Xviii Copyright 1995 Frank van der Linden. All rights reserved Theo DE Raadt Diff, grep Tcpd Xxii Los Alamos National Laboratory Apache Http server Xxiv Xntp Program Mrouted Xxvi PIM sparse-mode pimd Xxvii Ver Damage to the equipment or a disruption in service General Safety Guidelines Xxx Specific Warning Instructions Specific Caution Instructions To avoid damage to the equipment or a disruption in service For users in the UK and Denmark CleaningOther Instructions Storage Table of Contents Log Information Bridge ObjectsSnmp Objects Host Name Information GR2K-GA-0014 Iii Ver 100101 102 Index 177 132133 134 This page left intentionally blank GR2K-GA-0014 Vii Ver 118 111112 117 170 165166 169 Log Information Error Messages Default Values During Initial InstallationNAT-PT Error Messages DNS Resolver Information Error Messages Chapter 1 IPv4 Flow Control Flow InformationRange of QoS, Filter-Flow Control First input side stage executes the following functions Filter function on the first input side stagePacket in accordance with the flow Defines using and unusing of each control Constituting Definition Iinput Form Filtering/QoS Information Constituting Definition Input Form 2 IPv6 Flow ControlQos-ip-list, qos-ip-list-group, qos-ip Flow filter Interface Types that Support Flow Control Features of a flow filter input format are listed in TableFeatures of a flow qos input format are listed in Table Configuration Input Format IPv4 IPv6 Interface NameInput Output Side Types of action Flow control Effect Setting the informationFlow Flow Information Input Form Which a Cops agent function can be set to all RPs. It cannot Be changed when copsyes is set in the cops configuration Supported L2 UPC functions for each RP type √ Setting possible Setting not possible Conditions Queue Priority WAN Conditions Detection Priority Conditions Queue State of IP Output Priority *1 *2 Packet Type Flow Queuing ARP ARP Request/ARP Response packet By this router Layer 2 packet generated by IP header Definition Does not Coincide GR2K-GA-0014 Ver ROUTE-OS7 Priority Discard threshold User priority Send queue number Sett ng L2 UPC functions Fu ction can be setOut Action Pre autions Rela ed Commands RP-C, RP-C6 Flow filter Filter Flow Information 20 Maximum Definable Entries by Each PM Mounting Memory Size Changing only the operation designation When all high order protocol is targetFlow filter IPv4 Flow detecting condition and the operation Range Deletion of the information GR2000-1B RP-C6, RP-D6GR2000-2B Filtering/QoS Information Protocol No 22 General Protocol Number Lower Lower limit of the IP user data length is designated Upper Upper limit of the IP user data length is designated Input side Sets the Vlan ID of tag-VLANList information that sets this parameter should be set Inbound and specified as the flow detection conditions on Type Name 25 General Icmp Type and Code Nnumber26 General Icmp Type Number Type Name Code 27 List of Interfaces Supporting Flow Control Default -forward NoneOperation Parameter Interface name set in the information. Refer toTable Default -forward Range of value 0 to Packet Type Limited Filtering Item GR2K-GA Insertion Ists Forward Ignati n Filter Chan of pa ametersNdition and the operation List Tokyo Ti n par meter Let on of operati n d s gn Anyaciondrop Indicate IndicationIndication in input/output interf Display of blank Numb1 Related Informati n Related Commands Indication of a blank list number in the specified range Flow filter IPv6 ROUTE-OS6Input Format Indication of the information Parameter GR2000-2B Main Item Sub-Item Input Output Side Indication of top blank list number in the specified range IP-address information is designated. The IP information or This command. The RM Ethernet is not supported. For detailsDefault No default is possible Subject interface name set in the IP information or If all IPv6 addresses are designated any 30 General Protocol Number LowerLower limit of the IP user data length is designated UpperUpper limit of the IP user data length is designated General Port Number Result Parameter at the head of the whole operation parameter None No default is possible when designating the operation33 General ICMPv6 Type and Code Number Operation Parameters Interface Name Availability of Support 34 List of Interfaces that Support Flow Control Rward Flow Ver Ction Yes Pa ameter n for Tokyo Config# Deletion n list un t Cnfig#showflowfilter 3ffe501811ff0111 Display of top blank list number in all Display of blank Flow qos QoS Flow Information Filtering/QoS Information Related CommandsRelated Information Flow qos IPv4 SetflowqosInterfaceNameinout-disable Value Parametersminno Indication of blank list number the specified range Parameter Main Item Sub-Item Input Output Side Only GR2000-1B, GR2000-2B and GR2000-2B+ can be set Filtering/QoS Information Flow Control Operation Parameter Parameter 38 General protocol number IP User Data Port Dumber Name Decimal Default None Range of value 0 to40 General Icmp Type Code Number Description Specifies the Igmp type 41 Genral Igmp Type Code Number Range of value To 255 ten-decimals. Please refer to TableGeneral Icmp type number Page Filtering/QoS Information 43 Relationship Between Number of Queues and Priority Specifies the queuing priority after having been changed. If Packet Relationship Between Number of Queues and Priority Setting Contents Setting Parameter Number Entry 45 Number of Entries Used per List by Each Setting Tokyo and the transmitter addresses Flow Wflw Inserting t QosTokyo1out List Unit QosTok Put/output interface unit Delete Erface Tok o Out Filtering/QoS Information Related Information Flow qos IPv6 ROUTE-OS6 Indication of blank list number in thespecified range Minno Parameter GR2000-1B/2B Main Item Sub-Item Input Output Side Filtering/QoS Information Parameter User priority rewrite Replaceuserpriority Operation Parameter Flow Control 47 Operating Parameters that Can Be Set for Each Operation Ip-address information should be set before inputting this Command. RM Ethernet and Tunnel interface are notOut Outbound specification of the frame output side Or ip-address information. The ip information or 48 General Protocol Number Flow Detecting Condition Parameters All IPv6 addresses are designated any Default No default is possible Range of value IPv6 addressTo be designated is Range of value To 65535 decimal. Please refer to Table Upper limit of the IP user data length is designatedSpecifies the transmitter port number If port to be specified is one nnnnn Port Number Decimal Name 50 General Icmp Type Code NumberSpecifies the IGMPv6 type 51 General IGMPv6 Type Code Number Filtering/QoS Information 51 General IGMPv6 Type Code Number Default None Range of value 0 Default None Range of value 0 to Range Penaltydrop-penaltydiscarddNo.-penaltydscpDSCPValueVer.07-02 53 Relationship between number of queues and priority Examples 54 Number of Entries Used per List by Each Setting Specifies that packe Nlist4001ip Config# Conf ig# Conf List Cnfg#showflowqosTokyoout 103 List List401ip 105 Displaying Unit Display of top blank list number 40002-60000 GR2K-GA-0014 107 Ver Filtering/QoS Information PrecautionsConstituting Definition Inputting Form Function Filter Ressed to this outer Ort To show the information To create or modify the filter list information GR2K-GA-0014 111 Ver SubcommandTo show the first free entry No 56 Applicable Parameters by Upper Protocol Packet. The low-order 2 bits are ignored Specifies the value of high-order 6 bits in the TOS fieldCorresponding Values tos Value GR2K-GA-0014 113 Ver Default OnSetting by Filtering/QoS Information Corresponding Values Diff-serv Synchronized pair switch for the IP address upper -portpairoption checks for not switching and for-portpairoffoption only checks for not switching Protocol port number. The -portpairoption requires setting Checks for not switching source IP When specifying port numbers within a rangeOnly checks for not switching source Number. However, when -ippair or -portpair is specified GR2K-GA-0014 GR2K-GA-0014 117 Ver 60 Combination of Pair Switch61 Combined Setting of Pair Switch and Possibility of Use Combination of Pair Switch Setting Processing Default -syn off Range of value None Default -ack off Range of valueDefault Undefined Range of value Igmp Type No. h Input Value Decimal Name Specifies the Icmp code number in decimal63 Igmp Type Number GR2K-GA-0014 119 Ver Example 64 ReplaceTOS Field Rewriting Air Delete parameters of filter list information Ilt 123 Show filter list number 2 information Setfilter- groupFilter-Group-NameFilterListNo GroupFilter Before entering this commandDefault Undefined mandatory input Range of value 1024 To delete the filter group information Insert filter Ins t the con iguration information Groupip1 Group being used in the filter interface cannot be deleted Configuration ObjectsDelete filter list number 9 of filter group name ip1 Under which packets are relayed Specifies the target interface name predefined by the ip or To create the filter interface information Filterinterface128 GR2K-GA-0014 129 Filter interface Group Pre aution Related Co Transmission control Quality of Service QoS Objects Qos-ip-list, qos-ip-list-group Flow filter GR2K-GA-0014 133 Ver Qos-ip-list Qos-ip-list-group Non-IP protocol QoS control Setting informationNo disable 1 qos GR2K-GA-0014 135 Ver Yes enableSetting QoS parameters To enable flow control This parameter uses all interfaces by a Cops function Des Office1QoS inf rmation have been specified GR2K-GA-0014 137 Ver Qos yes Qos no Qos-queue-list Setting/modifying information Output priority control 67 shows parameters to be set per queue mode67 Parameters To Be Set Per Queue Mode Round-robin scheduling Minimum bandwidth guarantee 68 Maximum Range of Send Bandwidth Protocol GR2K-GA-0014 141 VerQueue Control Send Control Media Layer Less and indicate at least one queue within Queue modeIt is invalid in -priority or roundrobin mode. Bandwidth Allocation is determined by the line rate set this as a Bandwidthtraffic Number equally. Sets only when queue mode isEqualbandwidth. Invalid when queue mode is -priority Roundrobin, -bandwidth, -bandwidthkbps or ROUTE-OS6B Maxqueue Maximum queue count is Maximum queue count is 64*1 GR2K-GA-0014 145 Ver 10BASE-T 100BASE-TX 1000BASE-LX 1000BASE-LH Support Parameter 10BASE-T 1000BASE-LX 1000BASE-LH GR2K-GA-0014 147 Ver To set minimum Setting parameters To set the queueA mode for priorityTo queue1 and 80 percent to Bandwidth 149 Ue-st Ettings To display all sett ngs List Min To deleteSet can be Leted by sp cifying pa amet r name QueueA 152 Qos-interface Queue 75 Parameters That Can be Set by Each Transmission Control GR2K-GA-0014 155 Ver DefaultNone only the displayed value is supportedFiltering/QoS Information Parameters 76 Interface Names NEB1G-1B can be set at up to 590 Mbit/s Filtering/QoS Information Examples List When t Line center ethe Center Traffic Lineinterface GR2K-GA-0014 159 Ver 160 Ver 161 GR2K-GA-0014 To display all ettings 162 Dele Grup GR2K-GA-0014 165 Ver Qos-discard-mode Discard ModeDefault3 Range of value Discard Priority Class Mode Mod fying paramete s To change Setting parameters To set discard mode 2 on NIF numberTo delete t e NIF Mode Tting Deleting Free Unspecified Other Displaying the first free entry NoGR2K-GA-0014 169 Ver Flow-Detection Parameter Upper-Level Protocol Flow Detection Condition Parameters This parameter specifies the QoS IP frame condition listCondition Flow Control Parameter High-order bits in a TOS field or a DS field of Diff-serv, LimitsLimit This parameter specifies values corresponding to Single address is specified They overlap, set an IP address pair switch as ip-pair-offAddress is specified as -ipsource IP Address. An address Both source and destination IP addresses are set under one GR2K-GA-0014 173 Ver Igmp Type No. HEX Input Value Decimal Name Default None Icmp type is not a flow detection conditionThis parameter specifies the Icmp type 85 List of Igmp Type Number GR2K-GA-0014 175 Ver This parameter specifies an EXP field value. The numberFlow Control Parameters Flow control parameter GR2000-1B and GR2000-2B Default Operation Change Method Combined Setting Setting Sequence 87 UPC Combined Setting SequenceGR2K-GA-0014 177 Ver Maxpriorityclass 32 The maximum output priority is ProtectionMaxpriorityclass 8 The maximum output priority is Maxpriorityclass 16 The maximum output priority is GR2K-GA-0014 179 Ver Default Range of valueGreater Discard priority 88 Range of Priority Class and Discard Class 180 GR2K-GA-0014 Ver Range of Priority Class and Discard Class 90 Combination of Pair Switch TOS Number Calculation 91 Combined Setting of Pair Switch and Possibility of UseDelay Throughput Reliability TOS Number Formula to calculate the TOS number is Mapping of Class No. and Queue No. Max Output Priority is Setting Value ReplacingQueue No Class No Queue Count Matched Unmatched GR2K-GA-0014 185 Ver 96 Mapping of Class No. and Queue No. Max Output Priority is Sets only when output line protocol is frame relay Replacetos 240 -upc 1000000 -upcpenalty drop Source IP address RedGroup Maximum limitatTec ion Flow detection Ion parameter of important packet Flow detection Ndi ion parameter of prio ity packet Config189 No1 Rlace Modify parameters Delete se To display optional QoS IP frame condition list GR2K-GA-0014 193 Ver 97 Packet TypePacket type Output Priority Queuing 194 Deleting settings Insert ng e Display ng Dele e Qos-tos-map GR2K-GA-0014 197 Ver SettingsDefault See table below Default See table below Range of value 198 Output Queuing Mapping of TOS Value and Output/Queuing Priority ClassHatching part is RFC’s recommended value GR2K-GA-0014 199 Ver 200 Modifying param ters To change the-ueuingPrecedence Tos Deleting ttings 201 For the flow control, refer to the GR2000 Applications Guide Outbound setting frame output side Display settingsDefault Cannot be omitted Inbound setting frame input side Auti Config#To delete inbound Pre Line=0 Ver.07-02 Qos-ipx Default4 Range of valueGR2K-GA-0014 205 Ver Office1 Display ng sett ng To d s Lay All Lay the name f the optional interface Deleting settingsMod fying Arameters To hange the qu u ng prior 207 Precaution Mod fying parameters GR2K-GA-0014 209 Ver Displaying settings a. To display allIf this command To delete t Discard 2class Nterface Name4 Office1 Case of bandwidth and round-robin, used as queue Number DefaultParameter sets the output priority class. In the case Output priority control, used as the output priority class. Displaying Etting To disp ay Deleting etting To delete t SettingsDeleting param ter Case of output priority control Shaper shaper transmission information Set If the queuing mode is not omitted Supported Parameters for each queuing mode Queue number Default queue length 101 Default length of each queueParameter 1000BASE-SX Description 1000BASE-LX 1000BASE-LH Fair queuing 4WFQ Tting VLAN3 in we gh Displaying Setting information Ntee ethe specified bandwidth if the flow control Displaying random Vlan line name settingsDel Ing set ing information Pre Ution Cops Cops GR2K-GA-0014 219 Ver 102 Allowable Characters Set copspassword when setting this parameter Default3101 Range of value 0 to 65535 decimalDefault 3101 This parameter sets the server password encryption key Default3 Range of value 0 to Default BytesGR2K-GA-0014 221 Ver Chan ing Display ng setting information Deleting parameters Definition of Cops is deleted Related Commandsrimary 224 This parameter determines whether the IPX routing this IPX Objects1 ipx This sets the operation information for IPX routing Ange the IPX routing operati to D sable Default20 Range of valueSplay the content of the definitio Chan e paramet rs This parameter specifies the interface name to be set. Pay Setting information Changing informationIpx-interface IPX/Bridge Information Do not forward Forward diagnostic packet Default When the specified interface is ATM, WAN frame relay, orDefault None cannot be omitted This parameter is the forwarding switch when the diagnostic Send RIP packet Send SAP packet DefaultDoes not deliver this packet periodically Range of value 1-0xfffffffe in IPX Address Sett ng ReplyNetwork Interface Network To play Pt on PriodicDel Terface Description This specifies the node address MAC address Delete settingsDefault Cannot be omitted Range of value Is used Vpvc1 Forwarding destination of the IPX packet attached to This command allows setting of the IPX static routeStatic-route Registered static routing entry Erting parameters To the destination network based on the number of ticksAmong the routes to the destination network, the one with Smallest number of ticks has priority Related Comma ds Deleting set ingsIs xecuted, and the changed IP routing protocol Static-sap This command sets the static SAP informationNumber. The reference values are shown in -1 below Type Server Type Server Type Reference Values Atic Examples000000000001-fffffffffffe To display Hop Address ntwok444444443333333333 Outing p otocol information, and Mpls information are Pre aut onsReflected to the ope ation Parametersshowrip- No Inserting settings Ameter Displaying settings To display alTo d s Lay opt ons for RIP filtering en ry number Info mation entry number Prot col informa Ap ly command is not being executed, the apply subcommand is Filtering to be applied to receiving packets Default Filtered using a 4-digit hexadecimal number DefaultSpecifies all interfaces Default Network address xffffffff specifies all interfaces Default Displaying Tings To dis Lay al To insert new information Is donebefore the IPX packet is transmitted Prot col infoInformation, IP multic st rou Reflected to the p Ion Range of value 0-0xffffffff Changing settingsUsing 2-digit hexadecimal number Range of value 0-0xff Ing parame To ch Sockefiltering2forwardprotocol Inserting par Meters Filt ildr Reflectedconfig#to thedeleteipxoperat on-. filter1-network Object for display of the Bridge information If this command Is input dBridge Objects Bridge Bridge-interface You can define the bridge interface configurationDefining Frame format described here is only for MAC Default-enableOr more interfaces on the same bridge are connected to Same network Delet ng param te s Conf Uration display To display allTo display spec fic information Conf Ion deletion He bridge-interface of interface sk2 Default300 Range of value 10-1000000 IPX/Bridge Information Related CommandsFiltering-database This sets filtering drop deletes all frame destinations Interface address. It also deletes the frame when receivingSets the static entry MAC address to register with Filtering-database in canonical representation Delete Extended-filtering Recipient MAC address 6 octet Configure as filter1, then as filter2 and filter3Type field when the format is Ethernet No information Filtering. This is valid only when chosen type is user This parameter configures bit patterns hexadecimal thatConfigures bit patterns hexadecimal that check filtering Default Range of value 0-0xffffffffffff Del ting s ing Nform tion To delete Displaying setting information a. Display all informationExecuted before He command Display Speci c information Displaying information Default32768 Range of valueDefault Seconds Range of value Spanning-tree To del te t pr ority IPX/Bridge Information Precausion This page left intentionally blank To create or modify an Snmp Manager Snmp ObjectsSnmp Application of Snmp Information Objects Enabled. The individually specified trap is issued when Default Read Range of value Read or read-writeManager. When none is specified, no trap is performed. When Is specified, the standard trap is enabled. When extrap is Snmp Information Trap System Message Levels Default Protocol Range of value Interface or Is specifiedParameter Moment at Which coldstart trap is Issued Parameter Moment at Which link up/down trap is Issued Mode is selectiontrap Default Standard Range of value Or standard is specifiedParameter Moment Which link up/down trap is Issued Snmp Information Mthe Traprtransmission mode is selectiontrap GR2K-GA-0014 Spec fied trap are issued when selectiontrap is Related ConfigurDisplay register status of Snmp Manager Specifies the Rmon Ethernet history-group control index Default50 Range of valueHistory-control To create an Rmon Ethernet history-group control entry For allowable characters Default 1800 Range of value 3600Ethernet history events. This parameter corresponds to RFC1757 Wner Buckets Related Configu a ion Object Threshold. This parameter corresponds to alarmVariable AlarmTo create an Rmon Ethernet alarm-group entry Specifies the Rmon Ethernet alarm-group index number. This AlarmRisingThreshold of RFC1757 Threshold. This parameter corresponds to alarmIntervalCorresponds to alarmSampleType of RFC1757 Default Range of value Falling Short of the falling threshold. Such index number must be Is not issued. This parameter corresponds toAlarmFallingEventIndex of RFC1757 This setting. This parameter corresponds to alarmOwner Snmp Information Show the resulting alarm-group entries Alathreshold Alam Related Conf gu ion Objec Net history group can be referenced using an SnmpMake sure that Settings are Vabl Event. The trap option causes transmission of Snmp trap to EventTo create an Rmon Ethernet event-group entry Specifies the Rmon Ethernet event-group index number. This Example Howeve Latter Related Configu a ion ObjectsShow the registration status of Rmon event-group entry Event-group entries Hosts Host Name InformationTo create a host name entry Create a host name entry and show the result IPv4 Displa ing the configura ion informationCreate a host name entry and show the result IPv6 Dns-resolver Operation Management Information Precautions Validity of DNS resolver To delete domain name Effectuation He DNS relay Effectuates the DNS function Operation Management InformationDele On of set Dele DNS resolver information GR2K-GA-0014 Logger-syslog Log InformationNetwork by the following methods Displaying Logger Co fi Setting of log syslog informationSyslog informa Del tion Setting f Ou putting A notice level Logger-email Rmati n Re ated CommandsMail nformation Te the etting to send Event level Tting information Show ng To set information Logger-email-fromLog E-Mail Transmission Source Information To set information To delete information Logger-smtpLog E-Mail t ansmission source inf rmation is displayed Ginning Operation Management Information Parameter Re ated Command GR2K-GA-0014 Specifies the local e-mail address Setting information Setting enable/disableReport e-mail report information Sets whether or not to use the -mail report function Standard value Sending -mail reportsSpecifies the Smtp server port number for sending e-mail Reports Operation Management Information Example That enables -mail transmissions via the Internet Related Configura ion ObjectDefinitions Operation Management Information NTP Object ntp To create the NTP configuration informationThis set of parameters specifies the peer server Time servers defined Specifies the authentication key number used for accessingDefault No authentication key Range of Value Decimal Peer server. The key number must be the one defined by IPAddrss NTP Mode 6 and Mode 7 packets Ignores all accesses from the specified hostIgnores all the NTP Mode 6 and Mode 7 packets sent from Specified source. Time service with that source continues Up to 30 Ascii characters Enables the authentication key definitionDefaultOff DefaultNo authentication key Range of value Operation Management Information Related Standards NTP specifications of GR2000 are based on RFC1305 GR2K-GA-0014 Radius Radius server information Used the specified Radius server with priority Default Uses port number Range of Value 0Default Priority is not set Range of Value None Default Sec Range of Value 1Page Servers per device Deleting all Radius information To create board disablement definition Board Disablement Object disableCreate board disablement definition and show the result Precautions Related Configur tion Object Default Configuration ObjectsDefault Config# Direction Snmp Information Values during Initial InstallationInformation Information Name Initial Value Group Name 100BASE-LH Line Information Ethernet/Gibabit Ethernet Line Information WAN Disable -t3scrambleoff Line Information WAN OC-POS Refer to GR2000 Configuration Commands, universal Line Information ATM Subline Information WAN PPP Information PPPoE Information Frame Relay Information Initial Values during Initial Installation ATM Information 48163264 GFR2 Operation Management Information Parameters Isdn Information Japan Only Default Calls are suppressed Information Group Name Tunnel Interface InformationInformation Name Initial Value IP Interface Information ARP NAT-PT Information NAT-PT IPX Information Ipx filter Bridge information Attribute QoS Information Designation of queuing priority class for bridge Filter Information Example Related Configuration Object Router-defaultRouter-default Configuration Error Messages Message Contents Configuration Error MessagesCommon Router Control Information Router Control Information Error Messages Network Interface Network Interface Error Messages Attempt made to delete interface specified by QoS bridge Configuration Information Can not delete vc configuration with QoS NIF Invalid phone number Definition information name PCR No greater than 6144 kbps Network Interface Error Messages IP Information IP Information Error Messages An IP that has a VLAN-defined IPv4 address already set That VLANs in the same RP are unique Number of IP addresses exceeded maximum value. Decrease Local address for router information It is not possible to set IPv4 addresses in 6to4 tunnels Routing Protocol Routing Protocol Error Messages Aggregate linklocal address should be Attribute-list invalid BGPBGP4+ metric Option is peer Is not found. Use a defined interface address Peer type Passive option in the local peer Declaration only As peer group option Bgp This peer address Peer matches Bgp4+ invalid hold time value at ’Value’ not Peer must be agreed with the AS number of the own device Should not be v4-compatable Number At Value not in range 0 to Value Specified communities value Does not overlap with specified mask Than the local host address Configuration Error Messages Mask1 Lower limit of specified risk range Configuration Error Messages Shorter than prefix mask Mask2 Characters or hexadecimal 32 digits GR2K-GA-0014 Ospf invalid retransmit-interval value at He OSPFv3 domain number is duplicate-defined. Do not Stub parameter in backbone area Vpn specification range is invalid Ripng invalid aging time value at ’Time’ not GR2K-GA-0014 Value Extended community number Route-filter syntax error Syntax error Static address should not be v4-compat GR2K-GA-0014 Relation between the local address, and the IP address Multicast Routing Protocol Multicast Router Control Information Error Messages Local address, specify the defined interface address. Do not Igmp Interface not found at Address Group address mask Mask Mask Mask Multicastduplicate group address clause DVMRP, IGMP, Dvmrptunel Pim can not set interface address at Num Definition is wanted, add it using the following procedure Definition does not exceed the value Num2 specified for IPv6 Multicast Routing Protocol IPv6 Multicast Router Control Information Error Messages Definition Flow Information Error Messages Flow Information Error Messages Then delete the band setting or minimum band guarantee. Band assurance burst size, set the minimum band assurance Rewriting value, delete output priority or queuing priority Value, dscp rewritten value, tosmap, dscpmap, contract band Vlan priority rewrite value Band setting, delete the maximum band restriction or To the maximum band limitation burst size Each other Simultaneously. Specify the respective settings individually Dscp rewrite value or dscpmap has been defined. To set Can not set upc because group is already Filter and QoS Information Other than Flow Information Shaper configuration Value has set yet Destination network class and sub-network class An interface except the already set ATM line QoS IP list group entry number not specified Delete specification of the UPC penalty TOS modified value Allocation control traffic Mpls Information 10 Mpls Information Error Messages ROUTE-OS7 This is a duplicated definition of the to parameters Name is incorrect. For lsp and secondary lsp, designate One already defined for labelswitchedpath. To delete from IP address is a duplicated definition IPX Information 11 IPX Information Error Messages Filtering unique Not exceeding the set number of entries. To add entries, use Bridge Information 12 Bridge Information Error Messages Vrrp Information 13 Vrrp Information Error Messages Snmp Information 14 Snmp Information Error Messages Cops Information 15 Cops Information Error Messages Radius 16 Radius Error Messages Operation Management Information 17 Operation Management Information Error Messages Address Translation Information 18 Address Translaion Information Error Messages Maximum specifiable count of 1 rule Dhcp Server Information 19 Dhcp Server Information Error Messages NAT-PT 20 Dhcp Client Information Error MessagesNAT-PT Error Messages Dhcp Client Information Mail Sending Information DNS Resolver Information 25 Other Error Messages Other Error Messages GR2K-GA-0014 103 Ver Configuration file do not modified to standby GR2K-GA-0014 105 Ver Syntax error line Line No Index Index-2 Index