Hitachi GR2000 Series manual Should not be v4-compatable

Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2

Table 5-5 Routing Protocol Error Messages (continued)

bgp4+: the peer group option must be the	The settings of peer group option in the policy group are different.
same for policy group	The settings of peer group option in the policy group must be the
	same.
bgp4+: the peer option is link-local address,	The link local address is defined in the address of the internal peer.
but the internal peeras group is not supported	Define the global address or site local address in the peer address of
link-local address peering	the internal peer.
bgp4+:the refresh option must be specified	Parameters other than ipv6-uni are specified in the parameter of a
with ipv6-uni	refresh option. Do not specify parameters other than ipv6-uni in the
	parameter of a refresh option.
bgp4+:when the peer address is link-local	The peer address is a link local address, but a gateway option is
address, gateway option must not be	defined. Do not define a gateway option when a link local address is
specified	defined in the peer address.
configuration check error	Configuration information check error. If the identifiers (<id>) to be
	designated by the "attribute-list" command, the "network-filter"
	command and the "route-filter" command contain unusable
	characters, modify them to the correct identifiers (<id>).
dampen-flap: incorrect suppression	The parameter specified in dampen-flap definition is invalid. Specify
parameters	so as to meet the condition of reuse-below < suppress-above
	<max-flap.
dampen-flap: invalid keep-history-time value	The specified keep history time is invalid. Specify within the range of
at <value> not in range 1 to 86400	1 to 86400.
	<Value>: Specified keep history time
dampen-flap: invalid max-flap value at	The specified maximum flap value is invalid. Specify within the range
<value> not in range 1 to 30	of 1 to 30.
	<Value>:Specified maximum flat value
dampen-flap: invalid reach-decay-time value	The specified reach decay time is invalid. Specify within the range of
at <value> not in range 1 to 3600	1 to 3600.
	<Value>: Specified reach decay time
dampen-flap: invalid reuse-below value at	The specified reuse value is invalid.
<value> not in range 1 to 30	Specify within the range of 1 to 30.
	<Value>: Specified reuse value
dampen-flap: invalid suppress-above value at	The specified suppress value is invalid. Specify within the range of 1
<value> not in range 1 to 30	to 30.
	<Value>: Specified suppress value.
dampen-flap: invalid unreach-decay-time	The specified unreach decay time is invalid. Specify within the range
value at <value> not in range 1 to 3600	of 1 to 3600.
	<Value>: Specified unreach decay time
dampen-flap: out of range	The parameter-specified range is exceeded in the input command
	syntax. Numeric values of more than 4294967296 are contained.
	Reconfirm a parameter.
dampen-flap: syntax error	Syntax error
export: address not IPv6	Addresses other than an IPv6 prefix are specified.
	Specify the IPv6 prefix.
export: address should not be::	A default address is specified in an address.
	Specify addresses other than the local host address.export: address
	should not be v4-compatable.
export: address should not be v4-compat	An IPv4-compatible address is specified in an address.
	Specify addresses other than the IPv4-compatible address.
export: address should not be v4-mapped	An IPv4 mapped address is specified in an address. Specify
	addresses other than the IPv4 mapped address.
export: Attribute-filter " <Name>" cannot be	Filter information inherent to IPv4 is defined in IPv6. Do not specify
specified	the filter information inherent to IPv4.
	<Name>: Specified identifier

5-30	GR2K-GA-0014
	Ver. 07-02