Hitachi Gigabit Router GR2000 Series Enhanced Version Configuration Commands, Vol. 2

Table 5-6 Multicast Router Control Information Error Messages (continued)

pim: can not set interface address at

The interface addresses specified in the pim definition cannot be set.

<Address>

Do not specify the following interfaces because they are not

 

supported in the multicast.

 

(1) Interface of RM Ethernet

 

(2) Interface of AUX(RS232C)

 

(3) Interface in which the IP interface type is broadcast type in other

 

than LAN/WAN (PPP).

 

(4) Shared address interface.

 

(5) Local loop-back interface

 

(6) Null interface.

 

(7) Router device address (device address set by using the config

 

router command).

 

(8) Point-point type interface in which the destination IP address is

 

not specified.

 

(9) Tunnel interface.

 

<Address>: Specified interface address.

pim: dense and sparse can not be set up

Simultaneous settings of PIM-DM and PIM-SM are not permitted.

simultaneously

 

pim: duplicate group address and mask

The group address and the mask length of specified rendezvous

<Group address> / <Masklen>

point candidates have already been defined.

 

<Group address>: Specified multicast group address

 

<Masklen>: Specified mask length

pim: duplicate interface address in list at

Interface address is duplicated in pim definition. Specify not to

<Address>

duplicate interface address.

 

<Address>: Specified interface address.

pim: duplicate pim clause

pim definition is duplicated. Delete one definition.

pim: duplicate sparse parameter

sparse definition is duplicated. Delete one definition.

pim:duplicate ssm clause

Multiple PIM-SSM "ssm" commands are defined. The maximum

 

number is 1.

pim: Interface not found at <Address>

The interface of interface address specified in pim definition cannot

 

be found. Specify the defined interface address.

 

<Address>: Specified interface address.

pim: invalid candidate-bsr priority value at

The priority of BSR candidates exceeds the permissible range.

’<Num>’ not in range 0 to 255

Specify a value from 0 through 255.

 

<Num>: Specified priority

pim: invalid candidate-rp priority value at

The priority of rendezvous point candidates exceeds the permissible

’<Num>’ not in range 0 to 255

range. Specify a value from 0 through 255.

pim: invalid dense name

specified in pim definition is invalid.

 

Enter dense name with 1 to 14 characters.

pim: invalid inet mask bits value at <Masklen>

The specified range of the mask length set for rendezvous point

not in range 4 to 32

candidates for PIM-SM is illegal. Specify a value from 4 through 32.

 

<Masklen>: Specified mask length

pim: invalid interface address at <Address>

The interface address value specified in pim definition is invalid.

 

Enter the correct interface address.

 

<Address>: Specified interface address.

pim: local address and remote address belong

In the point-to-point interface, different subnets are set for the local

to different subnets on PointToPoint interface

address and the remote address. To operate PIM with the

<Address>

point-to-point interface, use the same subnet.

 

<Address>: Specified interface address

pim: mask length out of range from 4 to 32

The mask pattern specified for rendezvous point candidates of

 

PIM-SM exceeds the permissible range. Specify a mask pattern with

 

a mask length of 4 through 32.

pim: invalid inet mask length for interface

The mask length of the interface defined for PIM exceeds the

<address> not in range 8 to 30

permissible range. Set the interface mask length to 8 through 30.

 

<Address>: Specified interface address

 

 

5-58

GR2K-GA-0014

 

Ver. 07-02

Page 448
Image 448
Hitachi GR2000 Series manual Pim can not set interface address at