Hitachi GR2000 Series manual Ospf invalid retransmit-interval value at

	Configuration Error Messages
Table 5-5 Routing Protocol Error Messages (continued)
ospf: invalid retransmit-interval value at	In the OSPF area definition, the retransmit-interval value is out of the
<Value> not in range 1 to 65535	valid range. Specify a value within the range of 1 to 65535.
	<Value>: Specified retransmit-interval value
ospf: invalid router-dead-interval value at	In the OSPF definition, the router-dead-interval value is out of valid
<Value> not in range 1 to 65535	range. Specify a value within the range of 1 to 65535.
	<Value>: Specified router-dead-interval value
ospf: invalid seconds value at <Value> not in	Specified timer value is invalid.
range 0 to 4294967295	Specify a value within the range of 0 to 4294967295.
	<Value>: Specified timer value
ospf: invalid transit-delay value at <Value> not	In the OSPF definition, the transit-delay value is out of valid range.
in range 1 to 65535	Specify a value within the range of 1 to 65535.
	<Value>: Specified transit-delay value
ospf: invalid vpn number value at <Value> not	The range of VPN value is invalid. Specify a value within the range of
in range 1 to <Max_Value>	1 to <Max_Value>.
	<Value>: Specified VPN number
	<Max_Value>: Maximum VPN number
ospf: key id must be between 0 and 255	Specified MD5 authentication key ID is invalid. Specify a value within
	the range of 0 to 255.
ospf: keys cannot have same start time	MD5 authentication message digest generation start time is
	duplicated. Do not duplicate the start time.
ospf: mask not contiguous	Bit 1 of the specified mask does not continue. Use a mask where bit
	1 continues.
ospf: minute must be between 0 and 59	Specified time (minute) is invalid. Specify a value within the range of
	0 to 59.
ospf: month must be between 1 and 12	Specified month is invalid. Specify a value within the range of 1 to 12.
ospf: multipath option not valid for vpn route	The Multipath option is defined for VPN. VPN does not support
	multipath option.
ospf: neighbor-id must be an IP address	The IP address defined to neighborhood is invalid. Specify in IP
	address format.
ospf: net range already specified	Network parameter is already specified in OSPF area definition.
	Do not duplicate a networks parameter.
ospf: Non-masked bits not zero for <Address>	In masklen, 1 is specified for non-masked bit of the specified
masklen <Masklen>	address. Set non-masked bit 0.
	<Address>: Specified address
	<Masklen>: Specified mask length
ospf: Non-masked bits not zero for <Address>	In mask, 1 is specified for non-masked bit of specified address.
mask <Mask>	Specify 0 to non-masked bit 0.
	<Address>: Specified Address
	<Mask>: Specified mask
ospf: nssa option not valid for backbone	Nssa option is defined in a backbone area. Do not defined a nssa
	option in a backbone area.
ospf: out of range	The parameter-specified range is exceeded in the input command
	syntax. Numeric values of more than 4294967296 are contained.
	Reconfirm a parameter.
ospf: Router ID not defined	Router ID is not defined. Specify the Router ID.
ospf: secondary auth was overwritten by md5	In a specified virtual link, both MD5 authentication and the 2nd
for virtual link to <Neighbor ID> in Domain	authentication key are defined. Delete the unnecessary
<Domain ID> [on VPN <VPN ID>].	authentication method.
	<Neighbor ID>: router ID of the adjacent OSPF virtual link router
	<Domain ID>: specified domain No. of the OSPF virtual link
	<VPN ID>: specified VPN No. of the OSPF virtual link.
ospf: stop accept time must be later than start	MD5 authentication message digest accept end time is earlier than
accept time	start time. Set the value so start time is earlier than end time.
GR2K-GA-0014	5-41
Ver. 07-02