Configuration Error Messages

 

 

Table 5-5 Routing Protocol Error Messages (continued)

 

 

aggregate: linklocal address should be

An interface name is not specified in the specified link local address.

followed by % (IPv6 interface name)

Specify an interface name with the percent (%) interposed when

 

specifying a link local address.

aggregate: low end of range <Mask1> shorter

In the between specification, lower limit value of the mask range is

than prefix mask <Mask2>

overlapped with specified mask. Specify the value so that mask

 

range does not overlap with specified mask.

 

 

 

<Mask1>: Lower limit value of the specified mask range.

 

<Mask2>: Specified mask.

aggregate: low end of range (<Value1> bits) is

In the between specification, lower limit value of the mask range is

greater than high end (<Value2> bits)

greater than upper limit value. Reduce lower limit value of the mask

 

range to less than upper limit value.

 

 

 

<Value1>: Lower limit value of the mask range

 

<Value2>: Upper limit value of the mask range

aggregate: mask not contiguous

Bit 1 of specified mask does not continue. Use a mask where bit 1

 

continues.

aggregate: Non-masked bits not zero for

At mask, 1 is set to non-masked bit of specified address. Set

<Address> mask <Mask>

non-masked bit 0.

 

 

 

<Address>: Specified Address

 

<Mask>: Specified Mask.

aggregate: Non-masked bits not zero for

t masklen, 1 is set to non-masked bit of specified address. Set

<Address> masklen <Masklen>

non-masked bit 0.

 

 

 

<Address>: Specified address

 

<Masklen>: Specified Mask length

aggregate: not IPv6 prefix.

Addresses other than an IPv6 prefix are specified. Specify IPv6

 

prefix.

aggregate: out of range.

Input syntax command

aggregate: syntax error

Syntax error

attribute-list: attribute-list name "<Name>"

The specified ID exceeds 15 characters. Specify ID by 15 or less

longer than 15 characters

characters.

 

 

 

<Name>: Specified ID

attribute-list: duplicate Attribute-filter at

The specified ID number has been already registered. Specify the

<Value>

other ID number.

 

 

 

<Value>: ID number.

attribute-list: duplicate extended community.

The extended community is duplicated for definition. Do not duplicate

 

the extended community for definition.

attribute-list: duplicate Set-attribute at

The specified ID number has been already registered. Specify the

<Value>

other ID number

 

 

 

<Value>: ID number

attribute-list: error resolving’ <Host Name>’:

The specified host name is not found. Specify the defined host name.

Unknown host.

 

<Host Name>: Specified host name

attribute-list: invalid as_count value at

The specified ascount value is invalid. Specify within the range of 1

<Value> not in range 1 to 25

to 25.

 

 

 

<Value>: Specified ascount value.

attribute-list: invalid attribute-list number value

The specified ID number is invalid. Specify within the range of 1 to

at <Value> not in range 1 to 65535

65535.

 

 

 

<Value>: Specified ID number.

attribute-list: invalid autonomous system

The AS number is invalid in the extended community. Specify within

number value at <Value> not in range 1 to

the range of 1 to 65534.

65534

 

<Value>: Specified As value.

attribute-list: invalid autonomous system value

The AS number is invalid. Specify within the range of 1 to 65534.

at <Value> not in range 1 to 65534

 

<Value>: Specified As value.

attribute-list: invalid { BGP BGP4+ } metric

The range for specifying MED offset values is invalid. Specify within

offset value at <Metric> not in range 1 to

the range of 1 - 4294967295.

4294967295

 

<Metric>: Specified MED offset value

 

 

GR2K-GA-0014

5-21

Ver. 07-02

 

Page 411
Image 411
Hitachi GR2000 Series manual Aggregate linklocal address should be