Hitachi GR2000 Series manual Name is incorrect. For lsp and secondary lsp, designate

	Configuration Error Messages
Table 5-10 MPLS Information Error Messages [ROUTE-OS7] (continued)
label_switched_path: the explicit_route_name	The name is incorrect. For lsp and secondary lsp, designate
’<ER name>’ for the	separate explicit_route_name.
secondary_label_switched_path should not
	<ER name>: Specified route name
be the same explicit_route_name for the	<LSP name>: Specified LSP name
label_switched_path in ’<LSP name>’
label_switched_path: vpn is necessary in	In setting remote_vpn, specify vpn.
’<LSP name>’
	<LSP name>: Specified LSP name
label_switched_path: When VPN and	The flow_map and the vpn cannot be set simultaneously.
flow_map are set up, ether one only a side is
	<LSP name>: Specified LSP name
possible in ’<LSP name>’
label_switched_path: When VPN and	Simultaneous setting is not permitted for policy_mpls parameters of
policy_mpls in flow block are set up, either	the flow filter and vpn parameters of label_switched_path. Do not
one only a side is possible in ’<LSP name>’	specify LSP that uses VPN functions for a policy_mpls parameter of
	the flow filter. Also, do not make VPN settings for LSP that has been
	specified for a policy_mpls parameter of the flow filter.
	<LSP name>: Specified LSP name
label_switched_path:’<ER name>’ is	Unregistered explicit_route_name was designated. Or, an attempt
necessary	was made to delete the explicit_route_name being used. Designate
	the registered explicit_route_name.
	<ER name>: Specified route name
ldp: Can not change IP address	IP address can not change.
ldp: duplicate failed_init_session_threshold	This is a duplicated definition.
ldp: duplicate keep_alive_hold_timer	This is a duplicated definition.
ldp: invalid failed_init value ’<Value>’ not in	failed_init is out of range. Specify a value within the range of 0 to
range 0 to 65535	65535.
	<Value>: failed_init value
ldp: invalid IP address ’<Address>’	IP address is invalid
	<Address>: Specified address
ldp: invalid keep_alive value ’<HoldTimer>’	keep_alive value is out of range. Specify a value within the range of 1
not in range 1 to 65535	to 65535.
	<HoldTimer>: HoldTimer value
ldp: ip address ’<Address>’ is already used in	Designate the IP address which has not been designated in the
other ldp	separate block.
	<Address>: Specified address
ldp: IP address is mandatory	The IP address is a must.
lsr: duplicate hop_count_limit	This is a duplicated definition.
lsr: duplicate loop_detection	This is a duplicated definition.
lsr: duplicate path_vector_limit	This is a duplicated definition.
lsr: invalid hop_count_limit value ’<Value>’	hop_count_limit value is out of range. Specify a value within the
not in range 2 to 255	range of 2 to 255.
	<Value>
lsr: invalid path_vector_limit value ’<Value>’	path_vector_limit value is out of range. Specify a value within the
not in range 2 to 255	range of 2 to 255.
	<Value>: path_vector_limit value
MPLS is not supported	MPLS is not supported
mpls syntax error	MPLS configuration information is invalid.
	Set the correct configuration information.
mpls: Can not change ’<ER name>’ with used	The “route name” whose route was tried to be changed is being
	used.
	<ER name>: Specified route name
mpls: Can not delete ’<ER name>’ with used	The “route name” whose route was tried to be deleted is being used.
	<ER name>: Specified route name
mpls: Can not set IPv6 IP_Address	It is not possible to set IPv6 addresses in MPLS information.
GR2K-GA-0014	5-85
Ver. 07-02