Configuration Record Sheet | Honeywell UDC2500 instruction

Configuration

3.17 Configuration Record Sheet

Enter the value or selection for each prompt on this sheet so you will have a record of how your controller was configured.

Group

Prompt

Function Prompt

Value or

Selection

Factory Setting

Group

Prompt

Function

Prompt

Value or

Selection

Factory Setting

TUNING	PB or GAIN	_______	1.0
	RATE T	_______	0.00
	I MIN or I RPM	_______	1.0
	MANRST	_______	1.0
	PB2 or GAIN 2	_______	0.0
	RATE2T	_______	0.00
	I2 MIN or I2 RPM	_______	1.0
	CYCT1 or CT1	_______	20
	X3	_______	20
	CYC2T2 or CT2	_______	20
	X3	_______	20
	SECUR	_______	0
	LOCK	_______	NONE
	AUTOMA	_______	ENAB
	A TUNE	_______	ENAB
	RN HLD	_______	ENAB
	SP SEL	_______	ENAB

SPRAMP	SPRAMP	_______	DIS
	TI MIN	_______	3
	FINLSP	_______	1000
	SPRATE	_______	DIS
	EUHRUP	_______	0
	EUHRDN	_______	0
	SPPROG	_______	DIS

ATUNE	FUZZY	_______	DIS
	TUNE	_______	TUNE
	DUPLEX	_______	MAN
	AT ERR	Read Only	NONE

ALGOR	CTRALG	_______	PIDA
	TIMER	_______	DIS
	PERIOD	_______	0:01
	START	_______	KEY
	L DISP	_______	TREM
	RESET	_______	KEY
	INCRMT	_______	MIN
OUTALG	OUTALG	_______	NOTE 1
	OUTALG	_______	NOTE 1
	CRANGE	_______	4-20
	RLY TY	_______	MECH
	MTR TI	_______	5

INPUT1	IN1TYP	_______	K H
	XMITR1	_______	LIN
	IN1 HI	_______	2400
	IN1 LO	_______	0
	RATIO1	_______	1.00
	BIAS 1	_______	0.0
	FILTR1	_______	1
	BRNOUT	_______	UP
	EMIS	_______	1.0

INPUT2	IN2TYP	_______	1-5V
	LIN	_______	LIN
	IN2 HI	_______	2400
	IN2 LO	_______	0
	RATIO2	_______	1.00
	BIAS 2	_______	0.0
	FILTR2	_______	1

NOTE 1: Model Number Dependent.

4/07

UDC2500 Universal Digital Controller Product Manual

87

Image 101

Honeywell UDC2500 manual Configuration Record Sheet

Contents

UDC2500 Universal Digital Controller Product Manual Copyright 2007 by Honeywell Revision 5 April WARRANTY/REMEDY Contacts AbstractWorld Wide Web Telephone Symbol Definition Symbol Definitions Contents 136 Monitoring and Operating the Controller 158 151177 180 221 220222 226 Tables Introduction Introduction Figures Wiring Connections for Calibrating Current Output Page Overview FeaturesFunction Easy to Read Displays UDC2500 Operator Interface all display items shown Mount Anywhere MAN Function of Displays and Keys1Function of Displays and Keys Overview Process Instrument Explorer Software Depiction of infrared communications CE Conformity Europe Introduction What’s in this section? Introduction Condensed Specifications Condensed SpecificationsPre-installation Information Alarm Outputs RTU Frequency Hz Environmental and Operating Conditions Instructions Model Number Interpretation Model Number Interpretation Alarm Relays Control and Alarm Relay Contact InformationAlarm Relay Contact Information Control Relays Physical Considerations Overall DimensionsMounting Step Action Mounting ProcedureMounting Method Wiring Bundle No Wire Functions Permissible Wiring Bundling Universal Output Functionality and Restrictions Wiring DiagramsIdentify Your Wiring Requirements Tpsc INU Composite Wiring Diagram Wiring the Controller Line Neutral Voltage L2/N Earth Ground HotAC/DC RTD Input #1 Time Simplex Input #2Volts Input Milliamps Input Solid State Relay Output 10 Open Collector Output 12 Current Output 11 Dual Electromechanical Relay Option Output Open CW 15 RS-422/485 Communications Option Connections 17 Auxiliary Output and Digital Inputs Option Connections 12 + 26 + Configuration Topics Configuration Set Up Group Function Prompts Configuration Prompt HierarchyConfiguration Prompt Hierarchy Procedure Configuration ProcedureConfiguration Procedure Upper Display = SET Rate T Tuning Set Up Group RPM MINManrst Gain I2 MIN ALL Configuration is CompleteI2 RPM Secur Enable DisableAutoma RN HLD TI MIN SP Ramp Set Up GroupSP Ramp Setpoint Ramp Final Setpoint FinlspSprate Euhrup Spprog EuhrdnSetpoint RAMP/SOAK Program Strseg DIS StateHold Pvstrt Accutune Set Up Group Fuzzy Overshoot Suppression FuzzyTune Accutune Current Accutune Process 304 Accutune Error STATUS-When anAT ERR Ctralg Algorithm Set Up Group401 Onof Pida OuthysProportional Gain-Regulates Derivative Rate-Regulates Manrst in the Tuning Set Up group PD with Manual Reset is usedPdmr Three Position Step Control Start TimerPeriod Incrmt ResetDisp Outalg Output Set Up Group501 With Control algorithm prompt Tpsc Current Duplex Range Algorithm CrangeOutrng Current Duplex Range Full English Numeric Code Current Duplex Range SPLIT-ThisFor Example Mech RLY TYP Relay Cycle Time IncrementElectromechanical RELAY-Cycle MTR TI 601 Input 1 Actuation Type This Input 1 Set Up GroupIN1TYP IN1 HI XMITR1Transmitter Characterization RATIO1 IN1 LOBias FILTR1 Downscale Burnout will force DownNofs Emiss IN2TYP Input 2 Set Up Group701 Input 2 Actuation Type This XMITR2 IN2 LO IN2 HIRATIO2 FILTR2 Number of Tuning Parameter Control Set Up GroupPidset 801 TWO Sets SP Automatic TWO Sets PV AutomaticSW VAL LSP’S Rspsrc Power UP Controller ModeSP TRK PWR UP Action PwroutThree Position Control Step Hyst BandFailsf Three Position Step Failsafe Minrpm Failsafe ModeFsmode Auxout Options GroupAuxiliary Output Selection No Auxiliary Output Auxiliary Output LOW Scaling Deviation Process Variable0PCT No Digital Input Selections Auxiliary Output High ScalingDIGIN1 Inhibit Integral RESET-Contact External SP Program ResetManual Failsafe OUTPUT-Controller Keyboard LOCKOUT-Contact closure Setpoint INITIALIZATION-Contact Initiate Limit Cycle TUNING-ContactTo Remote SETPOINT-Contact closure Output Tracks Input 2-Contact Digital Input 1 Combination DI1COMPlus RUN Setpoint DIGIN2 Comsta Communications GroupCommunications Selection Irenab Txdly Shed Controller Mode and OutputWsflt Sdenab Shed Setpoint Recall ShdspUnits Percent Alarms Set Up Group TC W Deviation from LSP 2 NoteThermocouple Warning Note TC F LOW Alarm High AlarmA1S1VA A1S1HL Beginning of Segment A1S1EVEND of Segment A1S2TY A2S1EV A2S1HLA2S2TY A2S2VA Diagal ALARM1Block Decmal Display Set Up Group1201 Decimal Point LOCATION-This Disply FreqLwrdsp Lnguag Ethernet Configuration Screen 16 P.I.E. Tool Ethernet and Email Configuration Screens Email Configuration Screen Configuration Configuration Record Sheet Contrl AlarmsOption COM Whats in this section? Monitoring and Operating the Controller Entering a Security Code Operator Interface Lockout levels Lockout FeatureProcedure to Enter a Security Code Individual key lockout Key error Annunciators Monitoring Your Controller 4.5.1 Annunciators Lower Display Key Parameter Prompts Viewing the operating parameters Diagnostic Messages Diagnostic Messages Functional Overview Block Diagram of the UDC2500 Controller Auto-only Mode Access the ValuesSingle Display Functionality Exceptions Lower Display Prompt Upper Display Value Comments Single Display Parameters Upper Display = PV Value Start Up Procedure for OperationProcedure for Starting Up the Controller Control Modes Mode DefinitionsControl Mode Definitions Setpoints What happens when you change modesChanging Control Modes Dual Display Only Step Operation Press Result Select Until you see Switching between setpoints Timer10 Procedure for Switching Between Setpoints Configuration check Operation Viewing Times Accutune Tuning indicators Tune for Duplex Heat/Cool 11 Procedure for Starting TuneTune for Simplex Outputs Configuration Check for Duplex Using Automatic Tune at start-up for Duplex Heat/CoolUsing Blended Tune at start-up for Duplex Heat/Cool Using Manual Tune at start-up for Duplex Heat/Cool 108 16 Procedure for Accessing Accutune Error Codes Error Codes17 Accutune Error Codes Aborting Accutune Configuration Using Two Sets of Tuning ConstantsFuzzy Overshoot Suppression Completing Accutune 18 Set Up Procedure Set up ProcedureUpper Display = the switchover value Upper Display = SET Lower Display = Contrl Upper Display = the PV value Lower Display = Pids X X= 1 or Alarm SetpointsUpper Display = SET Lower Display = Alarms Estimated Motor Position Three Position Step Control AlgorithmDisplay Upper Display = PV Except 3 Position Step Upper Display = range= motor goes to closed position 100 = motor goes to open position Set Failsafe Mode 23 Procedure for Setting a Failsafe Mode Setting Failsafe ModeSetpoint Rate/Ramp/Program Overview PV Hot Start 24 Running a Setpoint Ramp 19Setpoint RampRUN/HOLD key 20Setpoint Rate Power OutagePower outages Program Contents Review program data and configuration25 Program Contents Setpoint Ramp/Soak Programming Ramp unit Contents Definition Ramp/soak profile example To Begin SEGRP Unit Soak Time Ramp Time Soak SP Program record sheet Run/Monitor functions Run/Monitor the program26 Run/Monitor Functions Function Press Result Lower Display = Recxx Power outage Digital input remote switch operationLower Display = XXHH.MM Loop Data 22 P.I.E. Tool Maintenance Screens Loop Data Maintenance Screen Alarm Details Maintenance Screen Loop Data Alarm Details Digital Input Details Screen Loop Data Digital Input Details Status Data Status Data Maintenance Screen Ethernet Status 10 Ethernet Status Maintenance Screen Configuring the Controller via Infrared Communications Configuring your Ethernet Connection 12 Online Configuration 14 Ethernet Communications Type Selection Configuring the Controller via Ethernet Communications 15 Ethernet Communications Address 16 Configuration Upload in Progress Input Calibration Select the Range Values Minimum and Maximum Range ValuesCalibration Steps W5W26 Sensor Type PV Input Range Range Values 100 %W5W26 low RP20-RP40 Voltage and Milliamp Equivalents for Input 2 Range Values Disconnect the Field WiringPreliminary Information Thermocouple Inputs Using an Ice Bath Input 1 Set Up Wiring Set Up Wiring Procedure for RTD Inputs Thermocouple Inputs Using a Thermocouple Source25R 26+ Millivolt or Volt Source 26+ Set Up Wiring Procedure for Milliampere Inputs Set Up Wiring Procedure for 0 to 10 VoltsTo 10 Volts Volt Source 100K pair 26+ Preliminary Steps Input 1 Calibration Procedure10 Input 1 Calibration Procedure Numeric Code Lower Display = Cjtemp Upper Display = Aply Lower Display = IN1SPNIf … Then … To 20 mA or 4 to 20 mA Inputs Input Input 2 Set Up Wiring25+ No connection No connection 26 + Input 2 Calibration ProcedureTo 2 Volts, 0 to 5 Volts, or 1 to 5 Volt Inputs Input 13 Input 2 Calibration Procedure Numeric Code 14 Restore Factory Calibration Restore Input Factory Calibration 150 Output Calibration Current Output Calibration Set Up Wiring Procedure for Current OutputCalibrator Connections 19+ Calibrate 100 % Current Output Calibration Procedure Numeric CodeCalibrate 0 % Auxiliary Output Calibration Set Up Wiring Procedure for Auxiliary OutputSet Lock in the Tuning Set Up group to None Calibration Mode Auxiliary Output Calibration Procedure Numeric CodeLower Display = Auxout Upper Display = a Value Upper Display = SET Lower Display = Tuning Restore Output Factory Calibration ProcedureRestore Factory Calibration Procedure Output Calibration Step Operation Press Result Troubleshooting/Service Troubleshooting Aids Customer support Procedure for Identifying the Software VersionDetermining the software version 32xx Status Tests Power-up Tests Background Tests Lower Reason for Failure How to Correct the Problem DisplayBackground Tests Fail PV LIM CnferrSegerr OUT1FL Symptoms Controller Failure SymptomsOther symptoms Display Output Cause Shooting Procedure Troubleshooting Procedures Troubleshooting Power Failure Symptoms Procedure #1Procedure #2 Troubleshooting Current Output Failure Troubleshooting Three Position Step Control Output Failure Procedure #3Refer to Installation for details Refer to Section Troubleshooting Time Proportional Output Failure Procedure #4 Refer to Output Calibration for details Procedure #5 10 Troubleshooting Alarm Relay Output Failure Procedure #6Refer to Configuration for Refer to Installation for relay contact information 11 Troubleshooting a Keyboard Failure Procedure #7 12 Troubleshooting a RS-485 Communications Failure Procedure #8 13 Troubleshooting an Ethernet Communications Failure Procedure #9Procedure #10 14 Troubleshooting Auxiliary Output Failure Step What to do Restoring Factory Configuration15 Restoring Factory Configuration 16 Software Upgrades Software Upgrades 176 UDC2500 Exploded View Exploded View Parts Identification Software Upgrades see SectionParts Not Shown Key Part Number Description Removing the chassis Other Modbus Codes Configuration ID TagsGeneral Information Register Address Structure Integer Parameter Type Register Name Access Numbers DecFloating Point Parameter Type Register Count Description Function Code 20 14h Read Configuration Reference DataRequest and Response Formats Byte Count File Number Reference Type DefinitionsRegister Address Register Address Format for Function Code Example #1 Read Configuration Examples Example #2 Write Restrictions Function Code 21 15h Write Configuration Reference Data Register Format Addresses Dec Hex Unrestricted RegistersRestrictions on Parameter Numbers in One Message Write Configuration Examples Non-volatile Memory Retention General Information Register Addresses Reading Control Data Control Data Parameters Read Software Options StatusRead Option Status SetPoint Program Read Only Information Miscellaneous Read Onlys Register Addresses for Read OnlysMiscellaneous Read Onlys SetPoint Program Read Only Information Setpoint Associated Parameters Setpoint Code SelectionsAssociated Parameters 1 Shed Timer Reset Using a Computer Setpoint Overriding Controller SetpointComputer Setpoint Selection Shed Computer Setpoint Associated Parameters Tuning Configuration ParametersSet-up Group Tuning Reading or Writing Lockout 0084 132 10 Set-up Group Setpoint Ramp/Rate SP Ramp/Rate/Program Controller Status 00B4 180 200 11 Set-up Group Accutune 12 Set-up Group Algorithm Algorithm 13 Set-up Group Output Output Algorithms 14 Set-up Group Input Input = NNM H Burnout Open 00A4 164 15 Set-up Group Input Input 00AB 171 16 Set-up Group Control Control = RPM 17 Set-up Group Options Options SP=PV 18 Set-up Group Communications Communications 19 Set-up Group Alarms Alarms Alarm 1 Setpoint 008E 142 INT 20 Set-up Group Display Display Function Code Field Modbus RTU Exception Codes Response Query21 Modbus RTU Data Layer Status Exception Codes Exception Definition Description Code Ethernet TCP/IP Further information Index UDC2500 Universal Digital Controller Product Manual 223 224 UDC2500 Universal Digital Controller Product Manual 225 Sales and Service UDC2500 Universal Digital Controller Product Manual 227 228