Millivolt or Volt Source 26+ | Honeywell UDC2500 instruction

Input Calibration

Radiamatic, Millivolts, Volts or Thermocouple Differential Inputs

Refer to Figure 5-5and wire the controller according to the procedure given in Table 5-7.

Table 5-7 Set Up Wiring Procedure for Radiamatic, Millivolts, Volts or

Thermocouple Differential Inputs (Except 0-10 Volts)

Step	Action

1Connect the copper leads from the calibrator to the Input #1 terminals as shown in Figure 5-5.

2Place current/voltage source at zero before switching on.

3Do not switch current/voltage source ON/OFF while connected to the instrument.

ATTENTION

For Radiamatic inputs only, set Emissivity value to 1.0. See Subsection 3.9 – Configuration Set Up prompt INPUT1, function prompt EMISS.

Millivolt or	+
Volt Source	_

26+

27-

Figure 5-5 Wiring Connections for Radiamatic, Thermocouple Differential,

Millivolts or Volts (Except 0 to 10 Volts)

142

UDC2500 Universal Digital Controller Product Manual

4/07

Image 156

Honeywell UDC2500 manual Millivolt or Volt Source 26+

Contents

UDC2500 Universal Digital Controller Product Manual WARRANTY/REMEDY Copyright 2007 by Honeywell Revision 5 April Abstract ContactsWorld Wide Web Telephone Symbol Definitions Symbol Definition Contents Monitoring and Operating the Controller 136 151 158177 180 220 221222 226 Tables Introduction Introduction Figures Wiring Connections for Calibrating Current Output Page Features OverviewFunction Easy to Read Displays Mount Anywhere UDC2500 Operator Interface all display items shown Function of Displays and Keys 1Function of Displays and KeysMAN Process Instrument Explorer Software Overview CE Conformity Europe Depiction of infrared communications Introduction Introduction What’s in this section? Condensed Specifications Pre-installation InformationCondensed Specifications Alarm Outputs RTU Environmental and Operating Conditions Frequency Hz Model Number Interpretation Instructions Model Number Interpretation Control and Alarm Relay Contact Information Alarm RelaysAlarm Relay Contact Information Control Relays Overall Dimensions MountingPhysical Considerations Mounting Procedure Mounting MethodStep Action Wiring Permissible Wiring Bundling Bundle No Wire Functions Wiring Diagrams Identify Your Wiring RequirementsUniversal Output Functionality and Restrictions INU Tpsc Wiring the Controller Composite Wiring Diagram Earth Ground Hot AC/DCLine Neutral Voltage L2/N Input #1 RTD Input #2 Volts Input Milliamps InputTime Simplex Solid State Relay Output 10 Open Collector Output 11 Dual Electromechanical Relay Option Output 12 Current Output Open CW 15 RS-422/485 Communications Option Connections 17 Auxiliary Output and Digital Inputs Option Connections 26 + 12 + Configuration Configuration Topics Configuration Prompt Hierarchy Configuration Prompt HierarchySet Up Group Function Prompts Configuration Procedure ProcedureConfiguration Procedure Upper Display = SET Tuning Set Up Group Rate T MIN RPMManrst Gain ALL Configuration is Complete I2 MINI2 RPM Secur Disable EnableAutoma RN HLD SP Ramp Set Up Group SP RampTI MIN Finlsp Setpoint Ramp Final SetpointSprate Euhrup Euhrdn SpprogSetpoint RAMP/SOAK Program Strseg State DISHold Pvstrt Accutune Set Up Group Fuzzy Fuzzy Overshoot SuppressionTune Accutune 304 Accutune Error STATUS-When an AT ERRCurrent Accutune Process Algorithm Set Up Group Ctralg401 Onof Outhys PidaProportional Gain-Regulates Derivative Rate-Regulates PD with Manual Reset is used Manrst in the Tuning Set Up groupPdmr Three Position Step Control Timer PeriodStart Reset DispIncrmt Output Set Up Group Outalg501 With Control algorithm prompt Tpsc Crange OutrngCurrent Duplex Range Algorithm English Numeric Code Current Duplex Range SPLIT-This For ExampleCurrent Duplex Range Full RLY TYP Relay Cycle Time Increment MechElectromechanical RELAY-Cycle MTR TI Input 1 Set Up Group IN1TYP601 Input 1 Actuation Type This XMITR1 Transmitter CharacterizationIN1 HI IN1 LO RATIO1Bias FILTR1 Down Downscale Burnout will forceNofs Emiss Input 2 Set Up Group IN2TYP701 Input 2 Actuation Type This XMITR2 IN2 HI IN2 LORATIO2 FILTR2 Control Set Up Group Number of Tuning ParameterPidset 801 TWO Sets PV Automatic TWO Sets SP AutomaticSW VAL LSP’S Power UP Controller Mode RspsrcSP TRK PWR UP Pwrout Three Position Control StepAction Band HystFailsf Three Position Step Failsafe Failsafe Mode FsmodeMinrpm Options Group AuxoutAuxiliary Output Selection No Auxiliary Output Deviation Process Variable 0PCTAuxiliary Output LOW Scaling Auxiliary Output High Scaling DIGIN1No Digital Input Selections External SP Program Reset Inhibit Integral RESET-ContactManual Failsafe OUTPUT-Controller Keyboard LOCKOUT-Contact closure Initiate Limit Cycle TUNING-Contact Setpoint INITIALIZATION-ContactTo Remote SETPOINT-Contact closure Output Tracks Input 2-Contact DI1COM Digital Input 1 CombinationPlus RUN Setpoint DIGIN2 Communications Group ComstaCommunications Selection Irenab Shed Controller Mode and Output TxdlyWsflt Sdenab Shdsp Shed Setpoint RecallUnits Percent Alarms Set Up Group Deviation from LSP 2 Note TC WThermocouple Warning Note TC F High Alarm LOW AlarmA1S1VA A1S1HL A1S1EV Beginning of SegmentEND of Segment A1S2TY A2S1HL A2S1EVA2S2TY A2S2VA ALARM1 BlockDiagal Display Set Up Group Decmal1201 Decimal Point LOCATION-This Freq DisplyLwrdsp Lnguag 16 P.I.E. Tool Ethernet and Email Configuration Screens Ethernet Configuration Screen Email Configuration Screen Configuration Configuration Record Sheet Alarms ContrlOption COM Monitoring and Operating the Controller Whats in this section? Operator Interface Entering a Security Code Lockout Feature Procedure to Enter a Security CodeLockout levels Key error Individual key lockout Monitoring Your Controller 4.5.1 Annunciators Annunciators Viewing the operating parameters Lower Display Key Parameter Prompts Diagnostic Messages Diagnostic Messages Functional Overview Block Diagram of the UDC2500 Controller Access the Values Auto-only ModeSingle Display Functionality Exceptions Single Display Parameters Lower Display Prompt Upper Display Value Comments Start Up Procedure for Operation Procedure for Starting Up the ControllerUpper Display = PV Value Mode Definitions Control Mode DefinitionsControl Modes What happens when you change modes SetpointsChanging Control Modes Dual Display Only Step Operation Press Result Select Until you see Timer Switching between setpoints10 Procedure for Switching Between Setpoints Configuration check Viewing Times Operation Tuning indicators Accutune 11 Procedure for Starting Tune Tune for Simplex OutputsTune for Duplex Heat/Cool Using Automatic Tune at start-up for Duplex Heat/Cool Using Blended Tune at start-up for Duplex Heat/CoolConfiguration Check for Duplex Using Manual Tune at start-up for Duplex Heat/Cool 108 Error Codes 16 Procedure for Accessing Accutune Error Codes17 Accutune Error Codes Aborting Accutune Using Two Sets of Tuning Constants ConfigurationFuzzy Overshoot Suppression Completing Accutune Set up Procedure 18 Set Up ProcedureUpper Display = the switchover value Upper Display = SET Lower Display = Contrl Alarm Setpoints Upper Display = SET Lower Display = AlarmsUpper Display = the PV value Lower Display = Pids X X= 1 or Three Position Step Control Algorithm Estimated Motor PositionDisplay Upper Display = PV Upper Display = range Except 3 Position Step= motor goes to closed position 100 = motor goes to open position Setting Failsafe Mode Set Failsafe Mode 23 Procedure for Setting a Failsafe ModeSetpoint Rate/Ramp/Program Overview PV Hot Start 19Setpoint Ramp RUN/HOLD key24 Running a Setpoint Ramp Power Outage Power outages20Setpoint Rate Review program data and configuration Program Contents25 Program Contents Setpoint Ramp/Soak Programming Contents Definition Ramp unit Ramp/soak profile example SEG RP UnitTo Begin Program record sheet Soak Time Ramp Time Soak SP Run/Monitor the program Run/Monitor functions26 Run/Monitor Functions Function Press Result Power outage Digital input remote switch operation Lower Display = XXHH.MMLower Display = Recxx 22 P.I.E. Tool Maintenance Screens Loop Data Loop Data Maintenance Screen Loop Data Alarm Details Alarm Details Maintenance Screen Loop Data Digital Input Details Digital Input Details Screen Status Data Maintenance Screen Status Data 10 Ethernet Status Maintenance Screen Ethernet Status Configuring your Ethernet Connection Configuring the Controller via Infrared Communications 12 Online Configuration Configuring the Controller via Ethernet Communications 14 Ethernet Communications Type Selection 15 Ethernet Communications Address 16 Configuration Upload in Progress Input Calibration Minimum and Maximum Range Values Calibration StepsSelect the Range Values Sensor Type PV Input Range Range Values 100 % W5W26W5W26 low RP20-RP40 Disconnect the Field Wiring Preliminary InformationVoltage and Milliamp Equivalents for Input 2 Range Values Input 1 Set Up Wiring Thermocouple Inputs Using an Ice Bath Thermocouple Inputs Using a Thermocouple Source Set Up Wiring Procedure for RTD Inputs25R 26+ Millivolt or Volt Source 26+ Set Up Wiring Procedure for 0 to 10 Volts Set Up Wiring Procedure for Milliampere InputsTo 10 Volts Volt Source 100K pair 26+ Input 1 Calibration Procedure 10 Input 1 Calibration Procedure Numeric CodePreliminary Steps Upper Display = Aply Lower Display = IN1SPN If … Then …Lower Display = Cjtemp Input 2 Set Up Wiring To 20 mA or 4 to 20 mA Inputs Input25+ No connection Input 2 Calibration Procedure To 2 Volts, 0 to 5 Volts, or 1 to 5 Volt Inputs InputNo connection 26 + 13 Input 2 Calibration Procedure Numeric Code Restore Input Factory Calibration 14 Restore Factory Calibration 150 Output Calibration Set Up Wiring Procedure for Current Output Current Output CalibrationCalibrator Connections 19+ Current Output Calibration Procedure Numeric Code Calibrate 0 %Calibrate 100 % Set Up Wiring Procedure for Auxiliary Output Set Lock in the Tuning Set Up group to NoneAuxiliary Output Calibration Auxiliary Output Calibration Procedure Numeric Code Calibration ModeLower Display = Auxout Upper Display = a Value Restore Output Factory Calibration Procedure Restore Factory Calibration ProcedureUpper Display = SET Lower Display = Tuning Output Calibration Step Operation Press Result Troubleshooting/Service Troubleshooting Aids Procedure for Identifying the Software Version Customer supportDetermining the software version 32xx Power-up Tests Status Tests Lower Reason for Failure How to Correct the Problem Display Background TestsBackground Tests Fail Cnferr PV LIMSegerr OUT1FL Controller Failure Symptoms SymptomsOther symptoms Display Output Cause Shooting Procedure Troubleshooting Procedures Procedure #1 Troubleshooting Power Failure SymptomsProcedure #2 Troubleshooting Current Output Failure Procedure #3 Troubleshooting Three Position Step Control Output FailureRefer to Installation for details Refer to Section Procedure #4 Troubleshooting Time Proportional Output Failure Procedure #5 Refer to Output Calibration for details Procedure #6 10 Troubleshooting Alarm Relay Output FailureRefer to Configuration for Refer to Installation for relay contact information Procedure #7 11 Troubleshooting a Keyboard Failure Procedure #8 12 Troubleshooting a RS-485 Communications Failure Procedure #9 13 Troubleshooting an Ethernet Communications FailureProcedure #10 14 Troubleshooting Auxiliary Output Failure Restoring Factory Configuration 15 Restoring Factory ConfigurationStep What to do Software Upgrades 16 Software Upgrades 176 Exploded View UDC2500 Exploded View Software Upgrades see Section Parts IdentificationParts Not Shown Key Part Number Description Removing the chassis Configuration ID Tags General InformationOther Modbus Codes Register Name Access Numbers Dec Register Address Structure Integer Parameter TypeFloating Point Parameter Type Register Count Function Code 20 14h Read Configuration Reference Data DescriptionRequest and Response Formats Byte Count Reference Type Definitions File NumberRegister Address Register Address Format for Function Code Read Configuration Examples Example #1 Example #2 Function Code 21 15h Write Configuration Reference Data Write Restrictions Unrestricted Registers Restrictions on Parameter Numbers in One MessageRegister Format Addresses Dec Hex Write Configuration Examples General Information Non-volatile Memory Retention Reading Control Data Register Addresses Read Software Options Status Control Data ParametersRead Option Status Miscellaneous Read Onlys Register Addresses for Read Onlys SetPoint Program Read Only InformationMiscellaneous Read Onlys SetPoint Program Read Only Information Setpoint Code Selections Associated ParametersSetpoint Associated Parameters Using a Computer Setpoint Overriding Controller Setpoint 1 Shed Timer ResetComputer Setpoint Selection Shed Computer Setpoint Associated Parameters Configuration Parameters TuningSet-up Group Tuning Reading or Writing Lockout 0084 132 SP Ramp/Rate/Program 10 Set-up Group Setpoint Ramp/Rate Controller Status 00B4 180 200 11 Set-up Group Accutune Algorithm 12 Set-up Group Algorithm Output Algorithms 13 Set-up Group Output Input 14 Set-up Group Input = NNM H Burnout Open 00A4 164 15 Set-up Group Input Input 00AB 171 Control 16 Set-up Group Control = RPM Options 17 Set-up Group Options SP=PV Communications 18 Set-up Group Communications Alarms 19 Set-up Group Alarms Alarm 1 Setpoint 008E 142 INT Display 20 Set-up Group Display Modbus RTU Exception Codes Function Code Field Query Response21 Modbus RTU Data Layer Status Exception Codes Exception Definition Description Code Ethernet TCP/IP Further information Index UDC2500 Universal Digital Controller Product Manual 223 224 UDC2500 Universal Digital Controller Product Manual 225 Sales and Service UDC2500 Universal Digital Controller Product Manual 227 228