III PERIPHERAL BLOCK: SERIAL INTERFACE

III-8 SERIAL INTERFACE

Configuration of Serial Interfaces

Features of Serial Interfaces

The Peripheral Block contains four channels (Ch.0, Ch.1, Ch.2 and Ch.3) of serial interfaces, the features of which are described below. The functions of these four serial interfaces are the same.

•A clock-synchronized or asynchronous mode can be selected for the transfer method. Clock-synchronized mode

Data length: 8 bits, fixed (No start, stop, and parity bits)

Receive error: An overrun error can been detected. Asynchronous mode

Data length:

7 or 8 bits, selectable

Receive error:

Overrun, framing, or parity errors can been detected.

Start bit:

1 bit, fixed

Stop bit:

1 or 2 bits, selectable

Parity bit:

Even, odd, or none; selectable

Since the transmit and receive units are independent, full-duplex communication is possible.

•Baud-rate setting: Any desired baud rate can be set by selecting the prescaler's division ratio, setting the 8-bit programmable timer, or using external clock input (asynchronous mode only).

•The receive and transmit units are constructed with a double-buffer structure, allowing for successive receive and transmit operations.

•Data transfers using IDMA or HSDMA are possible.

•Three types of interrupts (transmit data empty, receive data full, and receive error) can be generated.

Figure 8.1 shows the configuration of the serial interface (one channel).

 

 

 

 

 

 

 

 

 

Internal data bus

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Transmit data buffer empty

 

 

 

Control registers

 

 

 

 

Transmit unit

 

 

 

Receive unit

 

 

 

 

 

 

 

 

interrupt request

 

 

 

 

 

 

 

 

 

Data buffer

 

 

 

Data buffer

 

 

 

 

Interrupt

 

 

Receive data buffer full

 

 

 

 

 

 

 

 

 

and

 

 

 

and

 

 

 

 

control circuit

 

 

interrupt request

SOUTx

 

 

Serial output

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Receive error

 

 

 

 

 

 

shift register

 

 

 

shift register

 

 

 

 

 

 

 

 

 

 

control circuit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

interrupt request

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Serial input

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Ready signal

 

 

 

#SRDYx

SINx

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

control circuit

 

 

 

 

 

control circuit

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Start bit

 

 

 

Clock

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

detection circuit

 

 

 

control circuit

 

 

 

 

8-bit programmable timer output

#SCLKx

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 8.1 Configuration of Serial Interface

Note: Ch.0 to Ch.3 have the same configuration and the same function. The signal and control bit names are suffixed by a 0, 1, 2, or 3 to indicate the channel number, enabling discrimination between channels 0 to 3. In this manual, however, channel numbers 0 to 3 are replaced with "x" unless discrimination is necessary, because explanations are common to all four channels.

A-1

B-III

SIF

S1C33L03 FUNCTION PART

EPSON

B-III-8-1