Fujitsu M2488 manual Streaming, Start/Stop, E. Pt, Patha, Pathb, Level LO, Level HI, Loader

M2488 PRODUCT GUIDE MTU DIAGNOSTIC SPECIFICATIONS

The tests can be set using the following parameters:

DIAG parameter 1:		For “FRD READ”, “BWD READ” or “WRITE”, set the operation mode.
0x00	-	STREAMING	: Set a continuous read (or write) operation.
0x01	-	START/STOP	:	Set the start/stop operation.
	: For “LOCATE”, specify a sector. Specify a location sector from 1 to 99.
DIAG parameter 2: For “FWD READ”, “BWD READ”, “WRITE”, “FRD/BRD”, “L.W.R.” and “FEED
		THR”, specify a test wrap.
0x00	- WRAP 1		:	Wrap-1 test
0x01	- WRAP 2		:	Wrap-2 test
DIAG parameter 4: For “WRITE”, select a write data pattern from the following:
0x00	-	D.S.E. PT	:	D.S.E. pattern
0x01	-	2 F PT	:	2F pattern
0x02	-	1/6 F PT	:	1/6F pattern
0x03	-	1/5 F PT	:	1/5F pattern
0x04	-	1/4 F PT	:	1/4F pattern
0x05	-	1/3 F PT	:	1/3F pattern
0x06	-	1/2 F PT	:	1/2F pattern
0x07	-	1 F PT	:	1F pattern
0x08	-	1/12 F PT	:	1/12F pattern
0x09	-	1.5 F PT	:	1.5F pattern
DIAG parameter 5:		For “L.W.R.”, select a path of the Loop Write To Read command from the following:
0x00	-	PATH:A	:	Path A
0x01	-	PATH:B	:	Path B
DIAG parameter 6:		For “L.W.R.”, set a level of the Loop Write To Read command from the following:
0x00	-	LEVEL LO	:	Low level
0x01	-	LEVEL HI	:	High level

execution time: When diag parameter 1 is START/STOP, set the GO ON time (time when the tape is running).1 count is 10msec.

If this parameter is set to “0,” the GO ON time becomes 10 ms.

: For the path test, specifies start position by the machine reel counter.

stop time: When diag parameter 1 is START/STOP, set the GO OFF time (time when the tape is not running). 1 count is 10msec.

If this parameter is set to “0,” the GO OFF time becomes 0 ms.

: For the path test, specifies end position by the machine reel counter.

execute count: Specify an execution count. Specify a command execution count from 1 to 99,999. When 0 is set, the command execution continues with no stop.

H-4.3.2 LOAD/UNLOAD: Two diagnostic tests to check loading and unloading

(Set the tests in detail using the given parameters.)

1)	NO CTG:	Loader and Threader test not using cartridge-------	CMD CD : 0x20
2)	WITH CTG:	Loader and Threader test using cartridge.-------	CMD CD : 0x21

The tests can be set using the following parameters:

DIAG parameter 2:	For NO CTG, select a test type from the following:
0x00 -	LOADER	: Loader test
0x01 -	THREADER	: Threader test.
DIAG parameter 3:	For WITH CTG, select a loading position from the following:

April 1997 CG00000-011503 REV. A H-5