Operator Panel Top Level Menus Diagnostics Mode | Fujitsu M2488

M2488 PRODUCT GUIDE

MAINTENANCE AND SERVICING

Table 8-16. Operator Panel Top Level Menus - Diagnostics Mode

*

TEST and UNLOAD pressed

OFFLINE

TEST and UNLOAD released

DIAGMODE SETTING LOADCODE

TEST

INQUIRY

MODE PGS

FACTORY

Selection and execution of off-line diag- nostics

Product Guide Section 8-4

Access and configure user settable options

User Guide

Section 4-2

Copy new firm- ware from a code image tape cartridge into non-volatile memory of M2488.

User Guide

Section 4-3

View M2488 Information

User Guide Section 4-4

Display or change selected Tape Unit or Medium- Changer Mode Pages

User Guide Section 4-5

Change factory mode settings, enable factory mode, or enable factory diagnostics.

Product Guide Section 8-5

TEST

OFF-LINE

TEST

Run MTC			Run MTU		Run ACL
Run MTC			Run MTU		Run ACL

List Err

RS-232

Options

W/O CART

W/ CART

ALL

STOP ERR

CONT ERR

April 1997

CG00000-011503 REV. A

8-17

Image 327

Fujitsu M2488 manual Operator Panel Top Level Menus Diagnostics Mode, Off-Line, Cart ALL Stop ERR

Contents

Product Guide Page Preface Page Table of Contents Table of Contents M2488 Product Guide Design ArchitectureScsi Messages Tape Unit Scsi Commands Table of Contents Receive Diagnostic Results Factory Mode Receive Diagnostic Results Check Condition Send Diagnostic Factory Mode Check Tape Unit Parameters Media Changer Scsi Commands Additional Command Information on Medium Changer MC Medium Changer INQUIRY/CHANGE DefinitionTape Processing Maintenance and Servicing Xii C144-E019-03EN Parts Replacement Catalog Parameter List Diag Result Data M2488 Product Guide List of Figures List of Figures Top Cover List of Figures M2488 Product Guide M2488 Product Guide List of Tables List of Tables List of Tables M2488 Product Guide C144-E019-03EN Xix List of Tables C144-E019-03EN Xxi Xxii C144-E019-03EN C144-E019-03EN Xxiii Xxiv C144-E019-03EN Preparing the M2488 and ITS Optional Equipment Chapter Installation InstructionsConfigurations Introduction Installation Instructions M2488 Product Guide Rack-mount ConfigurationsRack-mount Desktop Configurations DesktopIPM Unpack the M2488 Tape Drive Unpacking Instructions ACL Unpack the Automatic Cartridge Loader Facl Unpack the Flush-mounted Automatic Cartridge Loader Inspect the Facl Equipment InspectionInspect the M2488 Tape Drive Inspect the ACL FACL? Assembly Instructions Interface Personality Module Installation IPMStep Action See Figure Cable and Power Connections Drive with ACL Attached 5-Cartridge Magazine Desktop Installation InstructionsTools Required Tape Drive Only Attaching Bases Drive with ACL Attached 10-Cartridge Magazine Stability Brackets Drive Positioning M2488 with Facl in Desktop Model Drive with Facl Attached 10. Attach to Bottom Base 11. Desktop Model Top Covers 12. Desktop Model Rear Cover 5.2.1 Inner Cover Mounted to Mounting Tray Rack-Mount Installation5.2 Adjust the Guide Plate 5.1 Tools Required Attach Mounting Tray 13. Guide Plate Installation Screw Plate Mounting 14 -inch Rack-mount Kit Installation 15. Bracket Adjustment Adjust the Brackets 16. M2488 Tray Mounting 17. M2488 with ACL Tray Mounting 19. Facl Face Plate Installation of the Automatic Cartridge Loader Equipment and Tools Required for ACL InstallationEquipment Part Number Quantity Description ACL 20. Prepare the M2488 Tape Drive Prepare the M2488 Tape Drive 21. Prepare the ACL Prepare the ACL 22. Connect the M2488 and the ACL Base Connect the M2488 and the ACL 23. Attach Operator Panel Cable to ACL Base Excess cable 25. Replace Covers Installation of the Flush-mount Automatic Cartridge Loader Equipment and Tools Required for Facl InstallationEquipment Part Number Quantity Description Facl 26. Prepare the M2488 Tape Drive 27. Prepare the Facl Prepare the Facl 28. Facl Rear Connect the M2488 and the Facl 29. Connect the M2488 and the Facl 31. Replace Top Covers Preparation for USEPage 2OPERATION of the M2488 Chapter Design Architecture Data Path Erdc Compression FeatureOperation of the Magnetic Tape Controller MTC Design Architecture M2488 Product Guide Microprocessor Control M2488 Product Guide Design Architecture Scsi BUS Operation of the Magnetic Tape Unit MTU FirmwareAirless Tape Path PCA-OP PCA-DVL CG00000-011503 REV. a April M2488 Scsi Messages Chapter Scsi MessagesM2488 Tape and Medium Changer Scsi Messages M2488 Product Guidescsi Messages Abort code 06h BUS Device Reset code 0ChCommand Complete code 00h Scsi Messages M2488 Product Guide Code Message Length Bytes M2488 Product Guide Scsi MessagesExtended Message Format code 01h Synchronous Data Transfer Request Sdtr Supported Scsi transfer rates are listed in Appendix G Bits Bytes Wide Data Transfer Request Wdtr Scsi Messages M2488 Product Guide Identify code 80h-FFh Ignore Wide Residue code 23hByte Value Description Message Parity Error code 09h Initiator Detected Error code 05hLinked Command Complete code 0Ah Linked Command Complete with Flag code 0Bh Restore Pointers code 03h No Operation code 08hSave Data Pointer code 02h Scsi BUS Status Reservation Conflict Status Page Tape Unit Scsi Commands ChapterLogical Units and Scsi IDS Command Description Paragraph Code M2488 Tape Scsi CommandsTape Unit Scsi Commands M2488 Product Guide M2488 Scsi Commands M2488 Product Guide Tape Unit Scsi Commands Command Description Block Format CDB Field DescriptionField Description Bits Bytes LUN Change Definition command 40hChange Definition CDB Description Change Definition Field Description Definition Parameter Description Change Definition ChangesValue Meaning of Definition Parameter Change Definition Check Condition Status Change Definition Sense KeysSense KEY Condition Description Display Field Description 11h Display CDB Description 11h Display Data 11h Display Parameter 11hDisplay Parameter Field Description 11h Space Display Data Display Mode Selection Bits 11h Display Sense Keys 11hQualifier Description Display CDB Description 10h 10. Display Field Description 10hLUN 11. Display Format Control Byte Description 10h Display Data 10h12. Display Parameter 10h 4.3 Display Sense Keys 10h 13. Display Mode Selection Bits 10h Immed BIT Long BIT Action Taken Erase command 19hErase CDB Description 14. Erase Field Description Not Ready Erase Sense Keys Data Protect Aborted Command Evpd Inquiry command 12hInquiry CDB Description 15. Inquiry Field Description Inquiry Data 16. Evpd Bit17. Supported VPD Page Codes Inquiry Check Condition Status 18. Inquiry Data Format 19. Inquiry Data Format Field Description Inquiry Data Format Field Description LUN Peripheral Description Qualifier Device Type 20. Peripheral Qualifiers21. Peripheral Device Type Code Description MTU Fujitsu 23. Default Vendor and Product Identification FieldsInquiry Sense Keys LUN Vendor ID Controller LUN Product ID Load Unload command 1Bh 7.1LOAD Unload CDB Description24. Load Unload Field Description Medium Changer Load Unload Check Condition StatusGAL Request Load Unload Sense Keys LSB Locate command 2BhLocate CDB Description 25. Locate Field Description 26. Block ID Format Locate Field Description 28. Format Mode Values 27. Block ID Format Field DescriptionFormat Code Value Locate Sense Keys Locate Check Condition Status LOG Select Check Condition Status LOG Select command 4ChLOG Select CDB Description 29. LOG Select Field Description LOG Sense command 4Dh LOG Sense CDB Description30. LOG Sense Field Description Field in CDB BUS Device Reset31. Page Codes LOG Sense Operation 32. Log Page Format LOG Sense Parameters 33. Log Parameter Format 34. LOG Parameter Field DescriptionETC=0 36. Log Sense Page 00h, Supported Log Pages Default Bytes Value Write Errors Detected by Firmware 37. Log Sense Page 02h, Error Counter Page WriteBits Default Bytes Value Write Errors Recovered by ECC Total Tapemarks Written Bits Default Bytes Value Bytes Transferred from InitiatorTMC=0 Total Write Blocks Read Errors Detected by Firmware 38. Log Sense Page 03h, Error Counter Page ReadBits Default Bytes Value Erase Gaps DUE to Retry Read Errors Recovered by ECC Total Read Blocks That Were Recorded in Edrc Format Total Errors CorrectedTotal Read Forward Bytes Bytes Transferred to Initiator Read Retries Total Read Blocks That Were not Recorded in Edrc Format 39. Log Sense Page 0Ch, Sequential-Access Device Error Statistics by Track 40. Log Sense Page 31h, Track Error Statistics Log Sense Page 31h, Track Error Statistics 136 175 LOG Sense Sense Keys Loop Write to Read command C1h Loop Write to Read CDB Description41. Loop Write to Read Field Description Loop Write to Read Sense Keys Hardware ErrorVolume Overflow Loop Write to Read Check Condition Status Byte BIT Valu Description Mode Select command 15hMode Select CDB Description 42. Mode Select Field Description Mode Select Data 43. Mode Select Parameter List Format45. Mode Select Parameter Header Field Description 47. Block Descriptor 46. Buffered Mode ValuesBuffered Description Mode Block Descriptor Block Descriptor Field Description Descriptor 49. Page Descriptors50. Page Descriptor Field Description Mode Select Sense Keys Mode Sense command 1Ah Mode Sense CDB Description51. Mode Sense Field Description 52. PC Field Mode Sense DataMode Sense Data Header 53. Mode Sense Data Header Bits Default Bytes 55. Buffered Mode Description 54. Mode Sense Data Header Field Description 57. Mode Select Parameter Header Field Description 56. Block DescriptorDescriptor 58. Page Descriptors Mode Settings Initiator Setup59. Page Descriptor Field Description M2488 Product Guide Tape Unit Scsi Commands Mode Sense Sense Keys Sili Read command 08hRead CDB Description 60. Read Field Description Read Check Condition Status Fixed Sili Block Description BIT Mode Are both set to one Read Sense Keys No SenseBlank Check Read command was aborted 62. Read Block Limits Data Read Block Limits command 05hRead Block Limits CDB Description 61. Read Block Limits Field Description Read Block Limits Sense Keys Read Buffer command 3Ch Read Buffer CDB Description63. Read Buffer Field Description Byte Mode Implemented BIT 64. Read Buffer Command ModeVendor Unique Mode 001b and Data Mode 010b 65. Supported Buffer ID Values for Read Data Mode 67. Read/Write Nvram Descriptor buffer ID Descriptor Mode 011b68. Descriptor Mode Field Description 66. Read/Write Data Buffer Descriptor buffer ID Boundary Offset Boundary Buffer Offsets 69. Offset Read Buffer Sense Keys Read Position command 34h 17.1READ Position CDB Description70. Read Position Field Description Read Position Return Data Bits Bytes BOP EOPMSB Byte BIT Description 71. Read Position Return Data Description 17.3 Description of Block ID Format 72. Block ID Field Description73. Format Codes Read Position Sense Keys Read Reverse command 0Fh 18.1READ Reverse CDB Description74. Read Reverse Field Description Invalid Field in CDB Read Reverse Check Condition Status Read Reverse Sense Keys Receive Diagnostic Results command 1Ch Receive Diagnostic Results CDB Description75. Receive Diagnostic Results Field Description Routine Parameter Code List Length 76. Receive Diagnostic Parameter List Length Field 79. Page 00h Supported Diagnostic Pages Diagnostic Page Codes PF=1 in Send Diagnostic command CDB77. Diagnostic Page Codes 78. Receive Diagnostic Results Page, General Form 81. Page 80h Field Description Receive Diagnostic Results Check Condition Status 82. Online Diagnostic Results data Parameter List Receive Diagnostic Results Sense Keys Mode Receive Diagnostic Results Factory Mode command 1ChReceive Diagnostic Results Factory Mode CDB Description 84. Receive Diagnostic Results Field Description Routine Parameter Code List Length 86. Diagnostic Page Codes 87. Receive Diagnostic Results Page, General Form88. Page 00h Supported Diagnostic Pages Factory Mode 00h Supported Diagnostic Pages Factory Mode 90. Page 80h Field Description 92. Page 81h Field Description 90-9Fh Online Diagnostic Test 95. Online Diagnostic Results data Parameter List Receive Diagnostic Results Sense Keys Bits Bytes Sili LUN Recover Buffered Data command 14hRecover Buffered Data CDB Description 97. Recover Buffered Data Field Description Recover Buffered Data Check Condition Status Recover Buffered Data Operation Recover Buffered Data Sense Keys Release Unit command 17h 22.1 Release Unit CDB Description98. Release Unit Field Description Release Unit Sense Keys Release Unit Operation Request Sense Check Condition Status Request Sense command 03hRequest Sense CDB Description 99. Request Sense Field Description Request Sense Sense Keys Report Density Support CDB Description Report Density Support command 44h Report Density Support Data 100. Report Density Support Field Description April CG00000-011503 REV. a 107 108 CG00000-011503 REV. a April Ucts is discouraged since the definition of bits may vary 104. Report Density Support Data Block Field Description 110 CG00000-011503 REV. a April Report Density Support Sense Keys Reserve Unit command 16h Reserve Unit CDB Description105. Reserve Unit Field Description Reserve Unit Operation Reserve Unit Sense Keys Rewind Check Condition Status Rewind command 01hRewind CDB Description 106. Rewind Field Description Rewind Sense Keys Send Diagnostic command 1Dh Send Diagnostic CDB Description107. Send Diagnostic Field Description Send Diagnostic Field Description 108. Send Diagnostic CDB Field Description OverviewRoutine Selftest Devofl Unitofl Parameter Code List Length Send Diagnostic CDB Field Description Overview Send Diagnostic Check Condition StatusDiagnostic Pages PF=1 109. Send Diagnostic Page, General Form 110. Diagnostic Page Codes111. Page 00h Supported Diagnostic Pages Description of the Page Code 80h 112. Page 80h Online Diagnostic Test 113. Diagnostic Parameter List Diagnostic Parameter List PF=0 Send Diagnostic Sense Keys 114. Send Diagnostic Factory Mode Field Description Send Diagnostic Factory Mode command 1Dh Send Diagnostic Factory Mode Field Description Send Diagnostic Factory Mode Check Condition Status Description of Page Code 00h 116. Send Diagnostic Page, General Form117. Diagnostic Page Codes 118. Page 00h Supported Diagnostic Pages Description of Page Code 80h 119. Page 80h Online Diagnostic Test Description of Page Code 81h 120. Page 81h Manufacturing Online Diagnostic Test Value of 1 is used to select Edrc Clear data transfer mode 122. Page 90-9Fh MTU Online Diagnostic Test Description of Page Codes 90-9FhList Diagnostic Parameter List PF=0 124. Diagnostic Parameter List 134 CG00000-011503 REV. a April 126. Code Field Bits Space command 11hSpace CDB Description 125. Space Field Description End-of-Tape Parameter Space Check Condition StatusFilemark Parameter End-of-Data Parameter Space Sense Keys Test Unit Ready Check Condition Status Test Unit Ready command 00hTest Unit Ready CDB Description 127. Test Unit Ready Field Description Test Unit Ready Sense Keys Write Check Condition Status Write command 0AhWrite CDB Description 128. Write Field Description Sense Data Information Bytes Buffered Mode Deferred Write Errors Early Warning IndicationAdditional Information Write Sense Keys 32.1WRITE Buffer CDB Description Write Buffer command 3Bh Mode Bits Implemented Modes 129. Write Buffer Field Description130. Write Buffer Modes Buffer ID Description Capacity M2488 Product Guide Tape Unit Scsi Commands Write Buffer Check Condition Status Microcode has Been Changed Write Buffer Sense Keys Write Filemarks command 10h Write Filemarks CDB Description132. Write Filemarks Field Description Write Filemarks Check Condition Status 133. Write Filemark Command OperationsBuffer Immed Operation Mode BIT Buffer Block Information Field Mode Write Filemarks Sense Keys Blank Check Aborted Command Scsi Reset Command DisconnectionPage Parameters Savable Bit All pages Chapter Tape Unit ParametersM2488 Product Guide Tape Unit Parameters Codes 00 -Vendor Unique Parameter Field Description Vendor Unique Parameter 00 Vendor Unique Parameter Played on the op panel display Tape Unit Parameters M2488 Product Guide Error Recovery and Reporting Parameters01 Error Recovery and Reporting Parameters Error Recovery and Reporting Parameters Field Description State of the other error recovery flags EER PER DTE DCR Description Valid Combinations of Error Recovery Parameters Dtdc Disconnect/Reconnect Control Parameters02 Disconnect/Reconnect Parameters 02 Disconnect/Reconnect Parameters Field Description Data Transfer Disconnect Control Eeca Rlec Chronous event notification EEG SEW BytesDBR BIS AVC Socf RBO REW Is changed to the value specified in the active format field 10h Device Configuration Parameters Field Description EOM Density Code 28h Density Code Description 7.1 M2488 Operation When Density Code 28h Is Not Configured7.2 M2488 Operation When Density Code 28h Is Configured When the Following is True Mode Sense will Report Tape Unit PARAMETERSM2488 Product Guide 18. VPD Page Format MTU INQUIRY/CHANGE Definition Vital Product Data Pages17. Supported MTU VPD Page Codes General VPD Page Format 19. VPD Page Format Field Description 21. Inquiry Data Format VPD Page 80h Unit Serial Number Supported VPD Pages Page 00h20. Inquiry Data Format VPD Page 00h Supported VPD Pages Unit Serial Number Page Page 80h 23. Inquiry Data Format VPD Page 81h Field Description Implemented Operating Definition Page Page 81h Ascii Implemented Operating Definition Page Page 82h 25. Inquiry Data Format VPD Page 82h Field DescriptionAscii Unit Usage Page Page C0h 26. Inquiry Data Format VPD Page C0h Unit Usage27. Inquiry Data Format VPD Page C0h Field Description Drive MTU Factory Configuration Settings Configuration Page Page C1h28. Inquiry Data Format VPD Page C1h Configuration Drive MTU Configuration Settings 30. Inquiry Data Format VPD Page C0h Field Description Controller Target Configuration SettingsProduct Identification Page Page C2h 29. Inquiry data format VPD Page C2h Product Identification Commands for Medium Changer Devices Chapter Media Changer Scsi CommandsMedia Changer Commands M2488 Product Guide Media Changer Commands Media Changer Commands M2488 Product Guide Exchange Medium MC command A6hExchange Medium CDB Description Source First Second Result Destination Exchange Medium ExamplesM2488A11 ACL Exchange Medium Examples M2488A12 Facl Exchange Medium Examples GAL Request Exchange Medium Sense Keys Mand Aborted COM Mode Select Field Description Mode Select MC command 15h M2488 Product Guide Media Changer Commands Mode Select Parameter List Format Mode Select Check Condition Status Descriptor Field Description Mode Select Parameter HeaderMode Select Mode Parameter Header Descriptors Mode Select MC Sense Keys Media Changer COMMANDSM2488 Product Guide Mode Sense Field Description Mode Sense MC command 1Ah PC Field Description Bits 10. PC Field 13. Page Descriptors 11. Mode Sense Data Header12. Mode Sense Data Header Field Description Descriptor Mode Sense MC Sense Keys 14. Mode Sense Page Descriptors Field Description Unit Attention Move Medium MC command A5h Move Medium CDB Description15. Move Medium Field Description 4.2 ACL/FACL Tables of Allowed Moves 16. XCL Allowed MovesSource Address Destination Result Move Medium Sense Keys Read Element Status CDB Description Read Element Status MC command B8h 18. Element Type Codes 17. Read Element Status Field Description 19. Element Addresses Read Element Status Data20. Block Structure of Read Element Status Data Element Status Data 21. Element Status Data Header22. Element Status Data Header Field Description Element Status 23. Element Status Page Header24. Element Status Page Header Field Description Element Descriptors 25. Medium Transport Element Descriptor Type Code = 1h26. Medium Transport Element Descriptor Field Description 28. Storage Element Descriptor Field Description 27. Storage Element Descriptor Type Code=2h 30. Import Export Element Descriptor Field Description 29. Import Export Element Descriptor Type Code=3h 31. Data Transfer Element Descriptor Type Code=4h 32. Data Transfer Element Descriptor Field Description Source and Destination Elements 33. Allowed Source and Destination ElementsRead Element Status Sense Keys 34. Test Unit Ready Field Description Test Unit Ready MC command 00h Logical unit is not ready magazine is not present 35. Page Codes Bits Mode Sense Default Bytes Values ACL Facl 37. Page Code 00 Device Unique Parameters Field Description 40. Operation of Cartridge Unload 38. Mode CodesCode Mode Sense Mode Select 39. Eject Codes 41. Cartridge Map P3PBytes Values 44. Facl Page Code 1Dh, Element Address Assignments Bits Mode Sense Default Bytes Values Reserved Code 9Eh Additional Page Length 02h Rotate 00h StorMT 1b 49. Facl Page Code 1Fh, Device Capabilities M2488 Product Guide Media Changer Commands IE → STDT → IE DT → ST Media Changer Commands M2488 Product Guide 51. VPD Page Format 50. Supported MC VPD Page Codes 53. Inquiry Data Format VPD Page 00h Supported VPD Pages 52. VPD Page Format Field Description M2488 Product Guide Media Changer Commands Implemented Operating Definition Page 81h Ascii Operating Definition Description Data Ascii Implemented Operating Definition Page 82h 56. Inquiry Data Format VPD Page C2h Product Identification Product Identification Page C2h M2488 Product Guide Tape Processing Changing Mode ParametersChanging Mode Parameters Permanent Error Handling Chapter Tape Processing Tape Processing M2488 Product Guide Permanent Write Error Permanent Error Handling Tape Processing M2488 Product Guide OZONExxxxyyyy text Chapter Maintenance and ServicingOperator Panel Displayed Error Messages M2488 Product Guide Maintenance and Servicing Nvram Initialization Required Maintenance and Servicing M2488 Product GuideDiagnostic Error Codes 4.1 Operator Panel Error Code Display Mode RTN Test Title Loops Errors Maintenance Terminal Error Code Display Error Code Sense Format Error Code 70 Sense Format on current commandSense Data Error Code 70 Sense Format Field Description Error Code 71 Sense Format deferred error reporting EOM ILISksv Error Code 71 Sense Format Field Description FMT Additional Sense Formats Format 01h Sense Information, FMT Sense Information BytesFormat 0 Sense Information Description for SIC Format 01h Sense Information for FMT Additional Format Error Information Type WTERR1 WTERR2 10. Format 01h Sense Information, Drive Field Description Command Code 11. MTC to MTU Commands 12. Format 02h Sense Information, Scsi Hardware Registers Format 2 and 3 Sense Information, Hardware Registers 24-27 SDDPHI.hdxc 28-31 13. Format 03h Sense Information, Edrc Hardware Registers 14. Format 04h Sense Information, Diagnostic Errors Format 4 Sense Information for Diagnostic Errors MTU Diagnostics Diagnostics1 Go/No-Go Diagnostics Off-Line Diagnostics 16. Operator Panel Top Level Menus Diagnostics Mode OFF-LINECart ALL Stop ERR Navigation keys Setting Procedure Command Selection Description Or Response ERR Operator Panel Off-Line Diagnostics Bold Command Description VARIABLES/ARGUMENTS +/- ces Commands KEYValid Macro Names Binary HEX Description Types of Diagnostic ProceduresTasked Go/No-Go Diagnostics 18. Options Byte Field Descriptions In-line Diagnostics 19. Selftest DescriptionTest Description Test Online Description Operator Routine Intervention 20. Page Code 80h Test Description Parameter Limit Diagnostic Test RegistryDiagnostic Microcode Specifications 21. Diagnostic Microcode Specifications 22. Operator Panel Top Level Menus Factory Option Factory Settings Option Settings Description Initial 23. Factory Menu Options and Settings Description Error Recovery Procedures Edrc Error RecoveryRetry Methods M2488 Product Guide Maintenance and Servicing Edrc Retry Signal Maintenance TerminalMaintenance Interface Signal Name Abbreviation Direction Remote Debug for JDB 25. Maintenance Interface Communications SettingsCommunications Setting Value Procedure Preventive Maintenance Tape Path Cleaning ProcedureStep Manual Tape Removal Procedure Cartridge Tape Stopped During LoadingGear Tape Wound on Take-up Reel Tape Stopped During Threading Remove and Replace Procedures Cable From Connector Description TypeM2488 Interconnects DVL CNP21 DTC CNJ21 DVL CNP42DVL CNJ43 DVL CNJ44 WTL CNP30 PSU CNP93 RDL CNJ12BCNJ90B RDL CNJ15 DVL CNJ22 Interconnect Diagram FRUs Remove and Replace Procedures Air Filter Remove and Replace Procedures Air Filter ReplacementAir Filter Removal Fan Assembly Replacement Fan Assembly Remove and Replace Procedures IPM Remove and Replace Procedures IPM ReplacementIPM Removal Top Cover Remove and Replace Procedures Top Cover ReplacementTop Cover Removal Bottom Cover Remove and Replace Procedures Bottom Cover ReplacementBottom Cover Removal DTC Pcba Replacement DTC Pcba Remove and Replace Procedures DTC Pcba Threader Assembly Remove and Replace Procedures Threader Assembly RemovalThreader Assembly Replacement Loader Assembly Remove and Replace Procedures Loader Assembly RemovalLoader Assembly Replacement OP PCA Remove and Replace Procedures OP PCA ReplacementOP PCA Removal Power Supply PSU Remove and Replace Procedures Power Supply RemovalPower Supply Replacement RDL Pcba Replacement SVL Pcba Remove and Replace Procedures SVL Pcba RemovalSVL Pcba Replacement RDL Pcba Remove and Replace Procedures RDL Pcba Removal WTL WTL Pcba Remove and Replace ProceduresWTL Pcba Replacement WTL Pcba Removal Maintenance and Servicing M2488 Product Guide Field Replaceable Units Chapter Parts Replacement CatalogM2488 Product Guide Parts Replacement Catalog Field Replaceable Units M2488 Tape Drive FRUs Top Side Parts Replacement Catalog M2488 Product Guide M2488 Tape Drive FRUs Bottom Side Scsi CNP07 CNJ06 CNJ04 CNP51 CNP55 CNP52 CNP54 WTL Pcba Sense KEY Description Appendix a Sense KeysM2488 Product Guide Sense Keys Table A-1. Sense Key Descriptions Sense Keys M2488 Product Guide Sense ASC/ASCQ Description Advised KEY Action Appendix B ASC/ASCQM2488 Product Guide ASC/ASCQ Table B-1. ASC and Ascq Description by Sense Key Advised Action Code Description ASC/ASCQ M2488 Product GuideTable B-2. Action Advised Codes ASC/ASCQ Description Advised KEY Action Table B-2 Action Advised Codes Table B-3. ASC and Ascq Description by ASC/ASCQAdvised Description Action Code Description KEY Table C-1. Erpa Codes Erpa Description Error CodeAppendix C Erpa Codes M2488 Product Guide Erpa Codes Erpa Codes M2488 Product Guide 3CAE Appendix D Fault Symptom CodesM2488 Product Guide Fault Symptom Codes Table D-1. Error Recovery 3CCB Fault Symptom Codes M2488 Product GuideTable D-2. Formatter Error Recovery 3CCA Table D-2. Formatter Error Recovery Table D-2. Formatter Error Recovery Table D-2. Formatter Error Recovery BC1D Table E-1. CHK xx Error Code Descriptions Appendix E CHK XX Error CodesCHK XX Error Code Descriptions M2488 Product Guide CHK XX Error Codes Table E-1 CHK xx Error Code Descriptions CHK XX Error Codes M2488 Product Guide Table E-1 CHK xx Error Code Descriptions Table E-1 CHK xx Error Code Descriptions Table E-1 CHK xx Error Code Descriptions Table E-1 CHK xx Error Code Descriptions CHK Code Description CHK XX Error Code Replacement ActionsTable E-2. CHK xx Error Code Replacement Actions CHK Replacement Code Action 13, 15 Table E-2. CHK xx Error Code Replacement Actions 13, 14 Table E-2. CHK xx Error Code Replacement Actions Table E-2. CHK xx Error Code Replacement Actions Table E-3. Replacement Action Codes PCA-DVL Appendix F Diagnostic Tests and Error Codes M2488 Product Guide Diagnostic Tests and Error CodesRoutine Test Diagnostic Modes Title Diagnostic Tests and Error Codes M2488 Product Guide Write EDRC-NC 3 bytes 00, mode 14h Read Compression err/sgd crc-a errors Read 4M tones test Routine Test Title Error Description Code Table F-2. Error Codes Common to all Routines/Tests Table F-3. Routine 1 Control Store Diagnostic Error Codes Diagnostic Tests and Error Codes Table F-5. Routine 3 CP Bus Parity Diagnostic Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Table F-8. Routine 6 Data Buffer Diagnostic Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Table F-11. Routine 9 PCC Timers Diagnostic Error Codes Diagnostic Tests and Error Codes Sddp ~SCSIREQ, SCSIACK, Scsibsy Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes ~SCSIREQ, SCSIACK, Scsibsy Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Sddp Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Dblk Diagnostic Tests and Error Codes Rsvp Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Dblk Diagnostic Tests and Error Codes Tected Table F-17. Routine 50 4M Tones Test Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Table F-19. Routine 80 Servo Diagnostic Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes Table F-25. Routine 90 Tape Drive Diagnostic Error Codes Diagnostic Tests and Error Codes Diagnostic Tests and Error Codes M2488 Product Guide Appendix G Supported Scsi Transfer Rates M2488 Product Guide Supported Scsi Transfer RatesTable G-1. Scsi Transfer Rates for 20 MHz Supported Scsi Transfer Rates M2488 Product Guide M2488 Diag Structure Appendix H MTU Diagnostic SpecificationsHOW to Execute the Diag Outline ACL test MTU Diagnostic Specifications M2488 Product GuideREAD/WRITE test LOAD/UNLOAD test Explanation MTU Diag ParameterCombination test Diag activation parameter Tape Path Diag READ/WRITE Ten diagnostic tests to check read and write Patha StreamingSTART/STOP E. PT Testmode Diagnostic test to measure operations ACL Test Two diagnostic tests to check the autoloader 3.4.3 M3AC/PS Measure the tape access/positioning time 3.4.4 M4MODCH Mode change time measurement3.4.1 M1LOAD Cartridge loading time measurement 3.4.7 M7D.S.E DSE time measurement 3.4.9 M9CLEAN Cleaning time measurement3.4.5 M5LOCAT Tape locating time measurement 3.4.6 M6REWND Tape rewinding time measurement Error reset command------- CMD CD 0x70 or 0xF0 Combination Running test by combining up to ten commands Parameter List MTU Diagnostic SPECIFICATIONSM2488 Product Guide April CG00000-011503 REV. a MTU Diagnostic Specifications M2488 Product Guide M2488 Product Guide MTU Diagnostic Specifications With Cartridge No Cartridge Name Code Diag command code Diag parameter Specify a sector M5LOCAT Diag parameter Execute time Stop time Execute count Reserve 0x80 Diag parameter END Diag Result Data MTU Diagnostic Specifications M2488 Product Guide M2488 Product Guide MTU Diagnostic Specifications MTU Diagnostic Specifications M2488 Product Guide M2488 Product Guide Flowcharts Appendix Flowcharts Lowchart igureFPanelOperatorFI-1 M2488FLOWCHARTSPRODUCT Guide MAG RUN ACL Flowcharts M2488 Product Guide List ErrorRUN CNT= ERR CNT= FGUIDELOWCHARTSM2488 Product REV Level Code Upload Complete Power OFFInsert Code Image Tape Loading Ready Unloading Copying Image MED-CHGR 10 StartWtrom Y Fsgrp T F6 Srnum F5 Ptime F4 MtimeNone Fsgrp S Diagnostic IndexM2488 Product Guide Index MTU Diagnostic SpecificationsDiagnostic Tests and Error Codes Diagnostics Index M2488 Product Guide Error Messages Error RecoveryInspection Mode SELECT/MODE Sense Commands Index M2488 Product Guide IPM Installation InstructionsMaintenance and Servicing Maintenance Terminal Mode Select and Mode Sense Commands VPD Commands ScsiScsi BUS Status Scsi Commands Changing Mode Parameters Index-8 CG00000-011503 REV. a April M2488 Cartridge Tape Drive Product Guide Comment FormPage M2488 Cartridge Tape Drive Product Guide Page