Subsystem subsystem, Subsystems all | IBM SC30-3681-08 specification

ELS Con®guration Commands (Talk 6)

list r

Remote Logging is ON

Source IP Address = 192.67.38.2

Remote Log IP Address = 192.9.200.1

Default Syslog Facility = LOG_DAEMON

Default Syslog Priority Level = LOG_CRIT

Number of Messages in Remote Log = 256

Remote Logging Local ID = MYHOSTNAME

status Lists the subsystems, groups, and events that have been modi®ed by the display, nodisplay, trap, notrap, trace, notrace, remote, and noremote commands.

Example:

list status

Subsystem:		TKR
Disp Levels:		STANDARD
Trap levels:		none
Trace levels:		none
Remote levels:		ERROR INFO TRACE
Syslog Facility/Level: LOG_USER LOG_INFO
Group	Disp	Trap	Trace	Remote
Mygroup	Unset	Unset	Unset	On
				Syslog Facilty/Level: LOG_DAEMON LOG_CRIT
Event	Disp	Trap	Trace	Remote
IP.007	Unset	Unset	Unset	On
				Syslog Facility/Level: LOG_CRON LOG_NOTICE

Note: Not only is remote logging enabled, but the display includes the Syslog Facility/Level values for each subsystem, group, and event. Ranges of events are listed as individual events.

subsystem

Lists names, events, and descriptions of all subsystems.

(Example output from a list subsystem command can be found beginning on page 191.)

subsystem subsystem

Lists all events in a speci®ed subsystem.

Example:

list subsystem gw

Event	Level	Message
GW.001	ALWAYS	Copyright 1984 Mass Institute of Technology
GW.002	ALWAYS	Portable CGW %s Rel %s strtd
GW.003	ALWAYS	Unus pkt len %d nt %d int %s/%d
GW.004	ALWAYS	Sys %s q adv alloc %d excd %d
GW.005	ALWAYS	Bffrs: %d avail %d idle fair %d low %d
GW.006	C-INFO	Pkt frm nt %d int %s/%d for uninit prt, disc
GW.007	C-INFO	Ip err %x nt %d int %s/%d
GW.008	U-INFO	Ip ovfl nt %d int %s/%d, disc
GW.009	UI-ERROR	Nt dwn ip rstrt nt %d int %s/%d
GW.010	UI-ERROR	Ip q len %d no ip buf nt %d int %s/%d
GW.011	U-INFO	Op err %x hst %wo nt %d int %s/%d
GW.012	U-INFO	Op err cnt excd hst %wo nt %d int %s/%d
GW.013	U-INFO	Rtrns cnt excd hst %wo nt %d int %s/%d
GW.014	UI-ERROR	Nt dwn op rstrt nt %d int %s/%d
GW.015	UI-ERROR	Nt dwn to hst %wo nt %d int %s/%d
GW.016	U-INFO	Op ovfl to hst %wo nt %d int %s/%d
GW.017	UE-ERROR	Intfc hdw mssng nt %d int %s/%d
GW.018	U-TRACE	Strt nt slf tst nt %d int %s/%d
GW.019	C-INFO	Slf tst nt %d int %s/%d
GW.020	U-TRACE	Nt pss slf tst nt %d int %s/%d
GW.021	UE-ERROR	Nt up nt %d int %s/%d
GW.022	U-TRACE	Nt fld slf tst nt %d int %s/%d

subsystems all

Lists all events in all subsystems.

Chapter 13. Con®guring and Monitoring the Event Logging System (ELS) 171

Image 207

IBM SC30-3681-08 manual Subsystem subsystem, Lists all events in a specied subsystem, Subsystems all

Contents

IBM Page IBM Research Triangle Park NC USA Ninth Edition November Contents Part 2. Understanding, Conguring, and Using Base Services Conguration Process Config Talk 6 and CommandsConguring and Monitoring the Config Process Protocol Qcong Set Time Unpatch Update Boot Config ProcessConguring Boot Config 145 Using the Event Logging System ELSOperating/Monitoring Process Gwcon Talk 5 Messaging Monitr Talk 2 Process Conguring and Monitoring the Event Logging System ELS Conguring Ieee 802.5 Token-Ring Network Interfaces Part 3. Understanding, Conguring and Operating InterfacesConguring and Monitoring Performance Getting Started with Network Interfaces Conguring and Monitoring ATM Using the Ethernet Network InterfaceConguring and Monitoring the Ethernet Network Interface Overview of LAN Emulation Conguring Serial Line Interfaces Using LAN Emulation ClientsUsing the X.25 Network Interface Conguring and Monitoring LAN Emulation Clients Conguring and Monitoring XTP XTP Conguring Commands 375 Add Change 378Conguring and Monitoring the X.25 Network Interface 327 405 Using Frame Relay Interfaces387 Conguring and Monitoring Frame Relay Interfaces Conguring and Monitoring Point-to-Point Protocol Interfaces Using Point-to-Point Protocol Interfaces Conguring Sdlc Relay Using the Multilink PPP ProtocolUsing Sdlc Interfaces Conguring and Monitoring Multilink PPP Protocol MP Conguring and Monitoring the V.25bis Network Interface Using Binary Synchronous Relay BrlyUsing the V.25bis Network Interface Conguring and Monitoring BSC Relay Using the V.34 Network Interface Using the Isdn InterfaceConguring and Monitoring the V.34 Network Interface Conguring and Monitoring the Isdn Interface Conguring and Monitoring Dial CircuitsAppendix A. Quick Conguration Reference Appendix B. X.25 National Personalities Appendix C. Making a Router Load File from Multiple DisksReaders Comments Ð Wed Like to Hear from You Xix Figures Xx MRS V3.2 Software Users Guide Xxi Tables Xxii MRS V3.2 Software Users Guide Xxiii Xxiv MRS V3.2 Software Users Guide Exclusion may not apply to you Resulting from this authorizationFor online versions of this book, you are authorized to All other copies of the documentation Xxvi MRS V3.2 Software Users Guide Trademarks Xxviii MRS V3.2 Software Users Guide Xxix PrefaceWho Should Read This Manual About the Software Ctrl-P Conventions Used in This ManualIBM 2210 Nways Multiprotocol Router Publications Separately from the device as part of the software order SC30-3680 Safety SD21-0030Operations and Network Management SC30-3681 SC30-3992 GC30-3867 Planning and Installation GA27-4068 Summary of Changes Moved into the Using and Conguring Featuresbook Editorial ChangesClarications and corrections Part 1. Understanding and Using the Software MRS V3.2 Software Users Guide Migrating to the Current Release Accessing the Software Using Local and Remote ConsolesGetting Started Before You Begin Local Consoles Telnet Connections Remote Login Names and PasswordsRemote Consoles Logging In Remotely or Locally Exiting the Router Reloading or Restarting the Router Understanding the First-Level User Interface Discussing the User Interface System Automatically starts Cong-Only and then enters Quick Cong Quick Conguration ProcessSystem Security Same as the Opcon process Status Using the SoftwareEntering Commands Connecting to a Process Getting Help Identifying Prompts Creating a First Conguration Exiting a Lower Level EnvironmentGetting Back to Opcon Some Conguration Suggestions Basing on an Existing Conguration Basing a Conguration on an Existing Conguration Accessing the Second-Level Processes Permanently Updating a CongurationTemporarily Updating a Conguration Are you sure you want to restart the router? Yes or No yes Accessing the Conguration Process, Config TalkEntering the Config Process Restarting or Reloading the Router Accessing the Network Interface Conguration Process Accessing the Operating/Monitoring Process, Gwcon TalkAccessing the Third-Level Processes Entering the Gwcon Command Process Following example adds a dial-out circuit Config list devicesFollowing example adds a dial circuit interface Following example adds a dial-in circuit Architecture Network Architecture Supported Interfaces Accessing the Network Interface Console Process Entering a Protocol Conguration Process Accessing Feature Conguration and Operating ProcessesAccessing Protocol Conguration and Operating Processes Accessing the Feature Processes + protocol Config protocol IP+configuration Entering a Protocol Operating Process Ctrl-Bfor Backward, and the current line is replaced with Command History for Gwcon and Config Command LineRepeating a Command in the Command History Enter Repeating a Series of Commands in the Command History Starting a Repeat Sequence As Commands Are EnteredExample Enter the following commands in Gwcon Starting a Repeat Sequence After All Commands Are Entered MRS V3.2 Software Users Guide Opcon Process MRS V3.2 Software Users Guide Using Opcon Accessing the Opcon ProcessOpcon Commands Syntax Divert BreakpointDivert Syntax Breakpoint Halt Flush Intercept LogoutMemory Memory Pause EasyStart onlyMemory Example Syntax pause Example Reload RestartStatus Comments Stop EasyStart onlyTTY1 or TTY2 Two dashes Example talk TalkTelnet Syntax Talk Display Three clients outbound from the routerSyntax Telnet Ip-address terminal-type Send ayt Not connected to a host Part 2. Understanding, Conguring, and Using Base Services MRS V3.2 Software Users Guide What is CONFIG? Conguration Process Config Talk 6 and Commands Configclear device Using EasyStartUsing the Config Talk 6 Process Configclear all Cong-Only Mode Automatic Entry Into Cong-Only ModeManual Entry Into Cong-Only Mode Quick Conguration Boot to Cong-Only mode Automatic Entry Into Quick Cong Mode Manual Entry Into Quick Cong ModeExiting from Quick Cong Mode Conguring User Access Technical Support AccessConguring Spare Interfaces Restrictions for Spare Interfaces Add a dial circuit using the add device commandCommands Access the Gwcon process by entering talk Activate them on the network using the activate command IPv6OSI/DECnet Resetting Interfaces Talk 5 +reset Restrictions for Resetting InterfacesTalk 6 Confignet 1 PPP Config Configprotocol ipx DNA Using the Config Talk 6 Process Enter the Opcon talk command and the PID for Config Conguring and Monitoring the Config ProcessEntering and Exiting Config Config Commands Config Commands Ppp-user Address-nameNetwork-dial-address Network-subdial-address Default value PasswordAllow inbound access Default value no Time-Allotted Default value noneNet-Route Mask Hostname Conguring Features Disable userExample with ECP encryption Tunnel-Server endpoint address Tunnel tunnel-nameSet shared secret Shared Secret Enter permission Enter passwordEnter password again Do you want to add Technical Support access? Device dial-circuit BootSyntax Boot Change Syntax Change pppuser Encryption-key Parameters Password Enter current passwordEnter new password Enter new password again Clear Tunnel-proleSyntax Clear Ip IP Wrs WAN Restoral featureCommand Default value is ªdisabledº Isdn-address address-name DeleteExample clear els Syntax Delete Enable Disable Modem-control carrier-wait or ring-wait service1 or service2 Enable Console-login Interface Modem-control Syntax Environment Environment CommandsEnvironment Command Summary Environment Event List FeatureSyntax Feature Feature# or feature-short-name Displays conguration information about the router Tunnel-prole Users V25-bis-address V34-addressDevices device or devicerange Conguration Pppusers Isdn-addressDisplays the current Isdn address congurations Patches Tunnel Name Call callbackDial dialback Encr encryption Syntax Patch NetworkPatch Networkinterface# Dls-ignore-lfs new value Ip-default-ttl #ofpacketsValid Values 0 to Default Value Ospf-import-rate rate Bgp-subnets new value Protocol Performance Baud-rate QcongSet Syntax Qcong Global-buffers max# Conguration commandInterface# # of seconds Logging disposition setting Inactivity-timer #ofmin Set prompt Only to increase itPrompt-leveluser-dened-name Additional functions as described in Table Syntax Time TimeReceive-buffers interface# max# Spare-interfaces n Offset minutes UpdateValid values -720 to Default value Unpatch Config Commands Config Commands Boot Config Process What is Boot CONFIG?Conguring Booting Using the Boot Config Process Using a Device as a Boot ServerHow the Bootp Forwarding Process Works Device as a Bootp Client IP Config enable bootp IP Config disable bootp Device as a Bootp Relay AgentEnabling/Disabling Bootp Forwarding Conguring a Bootp Server IP Config add BOOTP-SERVER IP address of server Using the Trivial File Transfer Protocol Tftp Accessing Conguration Files From a Remote Host or Router Filename Denitions for IBDExample 1 test.cfg Type of File Filename Extension IBD Considerations When Transferring a FileValidating the Conguration Load Conventions for File Name Extensions Dump Files Tftp Server, Boot and Dump DirectoriesLoading an Image at a Specic Time Conguring Dumping Installing Software/Code StatusTalk Enter exit Boot config list boot-entries Using the Boot Config Process Boot Config Commands Conguring Boot ConfigEntering and Exiting Boot Config Boot Config Commands Address Boot-entryAdd Syntax Add Add Boot Entry Parameters Bp-deviceLoads/name File name ? c\dump\gertrude.dmp Changeaddress Boot-entry Bp-device Dump-entryDump-entry Add dump-entry Change address Change bp-device Change which entry 1?Change dump-entry Copy Removes the specied interface as a Bootp device Ibd or lenameAddress # Loadname Disabledumping Unique-namingDescribe Describeloadname Loadname or bank-number EraseUnique-naming Syntax Erase Addresses List bp-device Boot-entriesDisplays the boot le conguration Dump-entries List view LoadSyntax Load Local Remote Local loadname Store Timedload Example 2. Load image source is the IBD DeactivateExample 1. Deactivate time activated load Example 1. Load image source is a remote host Host lename Syntax Tftp Get PutLocal lename Remote Host Host lename? Console display is the same as the Tftp get commandLocal lename? Remote Host? MRS V3.2 Software Users Guide 111 Boot OptionsDescription of Boot Methods Boot Method Description Bootp Using a Console Terminal Unsuccessful Bootp* indicates that the load image has nished loading Booting from a Tftp host server using a console terminal Boot Options AvailableAccessing the Boot Options Boot Option Prompts Boot OptionsOption Name Description Token Ring Prompts Boot Option PromptsPrompt Description Ethernet Prompts BC Boot in Cong-only Mode If you enter IBD, you see the followingTo reload the current conguration, pressEnter If you enter Ethernet, you see the following BM Boot using console queries If you enter Ethernet, you see the following BP Boot using Bootp BN Boot, But Do Not Run, Using Console Queries Diag Execute IBM Extended Diagnostic Program Dump using stored conguration UB Display Tftp Boot Conguration DM Dump using Console Queries This option is used only by your service representative UC Display Hardware CongurationUG Go execute at address in RAM LC Load Conguration Memory If you enter Token Ring, you will see the followingIf you enter WAN, you see the following Enter y and the console displays the message ZB ZModem BootCC Clear Conguration Memory ZC ZModem conguration memory load Conguring MRS V3.2 Software Users Guide Entering and Exiting Gwcon Operating/Monitoring Process Gwcon Talk 5 and CommandsWhat is GWCON? Gwcon Commands Gwcon Process Syntax boot ExampleGwcon Command Summary Activate Interface BufferSyntax Buffer Network# or rangeofnetwork# Syntax Conguration CongurationBytes Alloc Interface# or rangeofinterface# Hardware ConfigurationMAC/Data Link Type of MAC/Data link congured for the interface Available TestingDisabled State Current state of the network interface Disableinterface# Not PresentHW Mismatch Input Discards ErrorSyntax Error Input Errors Fault Log Interface Total routing memory Physical installed memorySyntax Log Syntax memory Example Temp Alloc ReserveNever Alloc Perm Alloc Ethernet X.25 interface by entering the X.25 operating commandsFor the following network and link-layer interfaces Bisync BSC Queue Queue Statistics Reset Number of bytes transmitted at the MAC layer TestUptime Bytes Trans Syntax Uptime Gwcon Process Entering and Exiting the Messaging Monitr Process What is Messaging MONITR?Commands Affecting Messaging Messaging Monitr Talk 2 Process Messaging Monitr 147 Using the Event Logging System ELSWhat is ELS? ELS is a subprocess that you access from the Opcon process Causes of Events Using ELSEntering and Exiting the ELS Conguration Environment Event Logging Concepts Logging Level Interpreting a MessageSubsystem Event Number Logging Level Type Packet Completion Codes Error CodesMessage Text Logging Levels ELS displays network information as follows Using ELSTo delete a group, use the delete command Groups See ªUsing ELS Message Bufferingº on Managing ELS Message RotationFollowing message is displayed Display subsystem srt all Display subsystem br all Using ELS to Troubleshoot a ProblemConguring ELS So Event Messages Are Sent In Snmp Traps ELS Example Talk Using and Conguring ELS Remote Logging Syslog Facility and LevelRemote Workstation Conguration Using ELS Syslog.conf Conguration File Conguring the 2210 for Remote Logging ELS configset remote no-msgs-in-buffer ELS configset remote source-ip-addrELS configset remote remote-ip-addr ELS configset remote local-id ** IBM/2210 Conguring Subsystems and Events for Remote Logging Remote Logging Output Msg Sample Contents from Syslog News Info File Output from Talk ELS Messages Containing IP Addresses Additional Considerations Using ELS Message Buffering Duplicate LoggingRecurring Sequence Numbers in Syslog Output Files None Using ELS MRS V3.2 Software Users Guide Conguring and Monitoring the Event Logging System ELS Accessing the ELS Conguration EnvironmentELS Conguration Commands ELS Conguration Command Summary This environment you congure message buffering ELS Conguration Commands TalkGroupname subsystem.eventnumber Conrm the creation of a new group Display Default Groups FilterSyntax Filter Net Lter-status Subsystems all SubsystemSubsystem subsystem Lists all events in a specied subsystem Nodisplayevent Group Range Subsystem NodisplayNoremote Trace-status Suppresses the remote logging of all ªtkrº messages Noremoteevent Group Range SubsystemGroup group.name Subsystem subsystem.name syslogfacility sysloglevel Syntax Notrap NotraceNotrap Notraceevent Group Range Subsystem Remote Remoteevent Range Group SubsystemNotrap range gw 19 Remote range gw 19 22 loguser loginfo Remote subsystem TKR all loguser loginfoGroup group.name syslogfacility sysloglevel Facility Pin maxtrapsRemote-logging Syntax Set remote-logging Localid No-msgsRemoteipaddr Sourceipaddr Syntax Set trace Default-bytes-per-pkt bytesTimestamp timeofday or uptime or off Timeofday Syntax Trace TraceStop-event event id Wrap-mode off or on Trap range gw 19 ELS Net Filter Conguration CommandsTrap Syntax Trap Syntax Create queue Create Disable EnableDelete All ELS Message Buffering Conguration CommandsList Log Syntax Nolog Nolog Set Wrap on or off Default value offEntering and Exiting the ELS Operating Environment Stop string text or none Environment you change message buffering operation ELS Monitoring CommandsELS Monitoring Commands Talk Advanced Displays messages for the specied event subsystem.event# FilesEvent subsystem. event# Subsystem subsystem.name Syntax Lter Net Syntax Les trace tftpHostIPaddr Lename List subsystem eth Groups group.nameList event ip.007 List pin Suppresses the displaying of messages for the specied event Subsystem allOccurred on the router Run-time information Level, such as there is with Remote Subsystem subsystemname logging-level Syntax NotraceSuppresses the display of the specied tracing event Gw.21, and gw.22 Remoteevent Group Range Subsystem Notrap subsystem tkr errorPacket Trace Syntax Packet-trace Remote event gw.019 loguser loginfo SyslogfacilitySysloglevel Retrieve RestoreSyntax Restore Remove Save Syntax RetrieveSyntax Save Facility Syntax Set timestamp Timeofday or uptime or off Timestamp Example statistics Decode off or onWrap-mode off/on Syntax statistics Not Subsys Name of subsystemVector Syntax View View Off CurrentSyntax Off Reset SubsystemsSyntax Subsystems Syntax Trace-status Example ELS Net Filter Monitoring CommandsTrace-Status View Syntax Create queue ELS Net Filter Monitoring Commands All Enable all currently congured lters All Lists all currently congured ltersLists the lter specied bylter# Release the buffer memory for other use by the system ELS Message Buffering Monitoring CommandsELS Message Buffering Monitoring Commands Flush Nolog Buffer-size Mbytes Buffer-size Mbytes System prompts you for it Command to a remote hostNew messages at the beginning of the buffer on Buffer formatted destipaddress destlename Scroll NoscrollNumber Performance Reporting Accuracy Accessing the Performance Conguration EnvironmentConguring and Monitoring Performance Performance Overview T2 output Performance Conguration CommandsPerf Conguration Command Summary Talk 6 Config Settime Accessing the Performance Monitoring EnvironmentPerformance Monitoring Commands Performance Conguration Commands Talk Performance Monitoring Commands Talk ReportSyntax report Example Time Performance Monitoring Commands Talk 221 Part 3. Understanding, Conguring and Operating Interfaces MRS V3.2 Software Users Guide 223 Network Interfaces and the Gwcon Interface CommandGetting Started with Network Interfaces Before You Continue Getting Started with Network Interfaces Dening Spare Interfaces Conguring Ieee 802.5 Token-Ring Network Interfaces Accessing the Token-Ring Interface Conguration ProcessToken-Ring Conguration Commands Token-Ring Conguration Command Summary Conguring Token-Ring Network Interfaces Packet-Size Token-Ring 4/16 Valid Packet Sizes Syntax Set Physical-address Rif-timerSet rif-timer Source-routing Speed Accessing the Interface Monitoring Process Syntax dump Example Token-Ring Interface Monitoring CommandsToken-Ring Monitoring Command Summary Dump Self-Test Fail Token-Ring Interfaces and the Gwcon Interface CommandStatistics Displayed for 802.5 Token-Ring Interfaces Self-Test Pass Using the Gwcon Interface Command Ring recovery actions # of times signal lostHard errors Auto-removal errors Removes received Lobe wire faultsBurst errors Token errors Using the Gwcon Interface Command Conguring and Monitoring LLC Interfaces Accessing the Interface Conguration ProcessLLC Conguration Commands LLC Conguration Command Summary Conguring LLC Rw-receive-window T1-reply-timerN2-max-retry N3-framesrcvd-before-ack T2-receive-ack-timer Ti-inactivity-timerTw-transmit-window Syntax Clear-counters LLC Monitoring CommandsClear-Counters Monitoring LLC Transmit Window Size Tw SAP value in hex 0FEMAX I-eld Size N1 Rcvd I-frame before ACK N3 Number of active sessions DisconnectingFrames refused by LLC user Cumulative number of sessions Session ResettingRemoteBusy FRMRReceived Source MAC addr Access PrioritySession Id Remote MAC addr No. of frames in ACK pend q Current send seq VsCurrent Rcv seq Vr Last ACKd sent frame Va N3-frames-rcvd-before-ack N2-maxretry Monitoring LLC Number of self-tests that failed Using the Ethernet Network Interface247 Number of self-tests that succeeded Using Ethernet Network Interfaces Multiple collisions Failed, carrier check or failed, carrier sense errorCD heartbeat error or SQE test error Internal mac tx errors or internal MAC trans errors Using Ethernet Network Interfaces Conguring and Monitoring the Ethernet Network Interface Accessing the Ethernet Interface Conguration ProcessEthernet Conguration Commands Ethernet conguration prompt ETH Config, is displayed Physical-Address Connector-TypeEthernet Conguration Commands Talk IP-Encapsulation Collisions Accessing the Ethernet Interface Operating ProcessEthernet Interface Monitoring Commands Ethernet monitoring command Summary Syntax collisions Example Ethernet Interface Monitoring Commands Talk Overview of LAN Emulation LAN Emulation Benets255 Physical Network Logical Network Simple LAN Emulation NetworkLAN Emulation Components Overview of LAN Emulation Addressing in ATM Broadcast and Unknown Server BUSATM uses 20-byte hierarchical addressing ATM Addresses of LAN Emulation Components ESI Manual Conguration of the Signaling Version Locating the Lecs Using IlmiOverview of Related Ilmi Functions Overview of the Lecs Function Overview of LAN Emulation Elan Name Policy Sample Situations for Use of the Lecs Assignment PoliciesATM Address Policy LAN Destination Policy Duplicate Policy Values More Information About TLVsElan Type Policy Max Frame Size Policy Control Distribute VCC point-to-multipoint Connecting to the LESControl Direct VCC bidirectional point-to-point From LE client to LES Address Resolution Connecting to the BUSAddress Registration Multicast Forward VCC point-to-multipoint BUS FunctionsMulticast Send VCC bidirectional point-to-point From LE client to BUS Establishing Data Direct VCCs Overview of Extensions for LAN EmulationBroadcast Manager BCM Support for IPX BCM Support for IP BCM Support for Source Route Bridging BCM Support for NetBIOS LAN Emulation Redundancy LAN Emulation Reliability LAN Emulation Security LEC Key Conguration Parameters for LAN Emulation 273 Using ATMHow to Enter Addresses ATM and LAN Emulation Conguring ATM and LAN Emulation Advantages of Using ATM Virtual InterfacesATM-LLC Multiplexing ATM Virtual Interface Concepts ATM Virtual Interface Conguration Concepts Disadvantages of using ATM Virtual Interfaces ATM Virtual Interface Conguration Concepts Accessing the ATM Interface Conguration Process Conguring and Monitoring ATM277 ATM Conguration Command Summary ATM Conguration CommandsATM Interface Conguration Commands ATM Conguration Commands Talk Example list esi Esi esi-addressSyntax List Conguration Esi Example list con Max-data-rate speed ATM Interface Conguration Commands TalkQoS Conguration Syntax Qos-conguration Max-callers Default Value ExampleValid Values Max-calls Max-mp-parties Max-frame Uni-version On or OFFYou are prompted for the VPI/VCI range you want to trace 65535 Address of End System Identiers Valid Values Default ValueUNI Network-id Syntax add Example Accessing the Virtual ATM Interface Conguration ProcessATM Virtual Interface Conguration Commands ATM Virtual Interface Conguration Command Summary Syntax Remove Example remove Accessing the ATM Monitoring ProcessATM Monitoring Commands ATM Virtual Interface Conguration Commands Talk ATM Interface Monitoring Commands ATM INTERFACE+ Prompt ATM Monitoring Commands TalkSyntax Atm-llc List ATM Interface Monitoring Commands TalkReserved-bandwidth Lists the reserved bandwidth on the ATM Interface Start WrapOff Stops packet tracing on all VCCs Syntax Wrap Syntax List Endpoints Channels ATM-LLC Monitoring CommandsATM Virtual Interface Monitoring Commands ATM LLC Conguration Command Summary Using LAN Emulation Clients LAN Emulation Client Overview291 MRS V3.2 Software Users Guide Syntax Add Ethernet Token Ring Token-ring Conguring and Monitoring LAN Emulation ClientsConguring LAN Emulation Clients 293 Syntax Cong Interface# Example configCong LE Client Cong Syntax Arp-conguration Example Conguring an ATM Forum-Compliant LE ClientARP Conguration Conguring Forum LE Clients Addmac route-descriptor ATM LAN Emulation Client ARP Cong Commands SummaryAdd Cong Remove RIF-Timer for Token-Ring Forum-compliant LEC onlySyntax Rif-timer Source-Routing for Token-Ring Forum-Compliant LEC only IP-Encapsulation for Ethernet ATM Forum-Compliant LEC only QoSSyntax IP-encapsulationEthernet Arp-aging-time Auto-cong Arp-cache-sizeArp-queue-depth Arp-response-time Bus-connect-retries Valid Values Default Value Connection-completion-timeBest-effort-peakrate 155000 Control-timeout Elan-nameEsi-address Default Value Frame-size ¯ush-timeoutForward-delay Forward-disconnect-timeout Les-atm-address Initial-control-timeoutValid Values Default Value Example Lecs-atm-address Multicast-send-type Any valid MAC addressMulticast-send-avg Multicast-send-peak Multiplier-control-timeout Path-switch-delayRecong-delay-min Selector Recong-delay-maxEnable or Disable Retry-count An integer number of frames in the range of 1 to Accessing the LEC Monitoring EnvironmentDefault Value Unknown-time Vcc-timeout Arp-table LEC Monitoring CommandsLE Cong monitoring command Summary Commands in Using and Conguring Features Current MAC Entries Current RD Entries ArpMax Table Size Free Table Entries For Token Ring IBM LEC+ list configIBM LEC+list config Lists the LEC conguration For Ethernet Lists VCC table StatisticsLists LEC statistics VCC table LecCongLanType LecControlTimeoutSyntax Mib LecCongMode LecPathSwitchingDelay LecLocalSegmentId LecVccTimeoutPeriodLecForwardDelayTime LecExpectedArpResponseTime LecFlushTimeout LecControlDirectVpi LecCongDirectVpiLecCongDirectVci LecControlDirectInterface LecSvcFailures QoS InformationLecControlFramesOut LecControlFramesIn Conguring Serial Line Interfaces Clocking and Cable Type317 Conguring Serial Line Interfaces Type set data-link Using the X.25 Network InterfaceBasic Conguration Procedures 319 Set Command Setting the National PersonalityUnderstanding the X.25 Defaults Using the X.25 Network Interface National Set Parameters National Enable ParametersParameter DDN Default GTE Default Paramter DDN Default GTE Default Conguration Changes Support Over Isdn BRI D-ChannelNull Encapsulation Limitations Closed User Group Null Encapsulation Understanding Closed User Groups Bilateral Closed User GroupsTypes of Extended Closed User Groups Conguring X.25 Closed User Groups Overriding Closed User Group Processing for CUGEstablishing Incoming X.25 Circuits for Closed User Groups Using the X.25 Network Interface 327 Conguration Commands25 Conguration Commands Summary Conguring and Monitoring the X.25 Network Interface Calls-out value Conguring the X.25 Network Interface Default NRZ Equipment-type DCE or DTE Valid Values 1 to Default ValueDefault external Default-window-size value Default Pvc low Pvc high Speed speed-settingNational-personality GTE-Telenetor DDN Pvc low/high value Default 2400 bps Valid values 0 to Default values Two-wayValid values 0 to Default values Svc low Svc high Outbound Valid values Default Lower-dtr Syntax Enable DdnÐaddress-translationsIncoming-calls-barred Lower-dtr Outgoing-calls-barred Incoming-calls-barred GTE Default National EnableSyntax National enable DDN Default DDN Default GTE Default Frame-ext-seq-mode Bi-cug-outgoing-accessCug-incoming-access Cug-outgoing-access National Disable Call-req Clear-req retries or timerNational Set Syntax National set DDN Default GTE Default N2-timeouts TimerDisconnect-procedure passive or active Dp-timer Maximum Reset retries or timerSpecies the number of reset request retransmissions DDN Default GTE Default Min-connect Restart retries or timerCollision-timer Min-recall DDN Default GTE Default Truncate-called-addr-size National RestoreT1-timer T2-timer Bi-cugs CugsHtf-address CUD Field Usage IP exampleIPX example Enc Priority Pref cug Valid values 0 to Default value NoneValid values 0 to Default value None Pref bi-cug Valid values 0 to Default value None Example Valid values 0 to Default value None Bi-cugs Species the closed user group number for this DTEAdd bi-cugs Qllc example Htf-addressAdds a Defense Data Network DDN X.25 address translation Convert HTF address Maximum VCs Default Packet SizeMaximum Packet Size Circuit Idle Time Sec Request Reverse ChargesStation Type Pri Changes a Defense Data Network DDN X.25 address translation Syntax ChangeaddressHtf-address Protocol Pvc Htf address Deletes an X.121 address translation Changes PVC, window size, and packet size denitionsRange of circuits dened by the Packet Channel Range Start Parameter Protocol prot-type Cugs List address Example list allLi cugs Summary DetailedProtocols Lists all the dened PVCs Monitoring Commands 25 Monitoring Command SummaryExample list summary List svc ParametersPacket Displays the parameters for the packet level Displays the statistics for the packet level PhysicalDisplays the parameters for the physical level Syntax Statistics all Statistics packet Statistics Displayed for X.25 InterfacesDisplays the statistics for the physical level +interface Data Bytes Interface statePacket Counters Data Packets Invalid Packets Received Switched Circuits OpenLast port reset Input frame errors CRC error Output aborts sent Output frame counters DMA/FIFO underrun errorsMissed frame Bits not set Conguring the X.25 Network Interface Using XTP X.25 Transport Protocol361 Conguration Information Using XTP Remote DTEs DTE Address WildcardsLocal DTEs Peer Routers XTP Backup Peer Function XTP configadd local-dteSearching for a Remote DTE Connection Request Timer Local XTPXTP and Closed User Groups Conguring XTP Conguration Procedures Set the Internal IP address Congure XTP Setting the Data LinkConguring the IP Interface Interface Enter set speed followed by the access rate line speed Exit the X.25 Config promptEnter add pvc to dene individual PVCs Dening the IP Address Setting the Internal IP AddressConfigprotocol ip IP configadd address IP configset internal-ip-address Add bi-cug XTP configadd peer-routerXTP configadd remote-dte Add cug Remote DTE At ªConguration Proceduresº onSample Conguration of Remote Routers Remote 1 router Configprotocol xtp Configprotocol xtp XTP configadd local-dteRemote 2 router Routers IP address?128.185.100.1 Using XTP XTP Conguring Commands Conguring and Monitoring XTP375 Address for that call XTP Conguring Commands TalkLocal-dte With XTP are 0 to Add local command Remote-dteRefer to Software Users Guide Syntax Change Refer to the Software Users Guide Cug Syntax disable-xtp Syntax enable-xtp Remote-dtes Keep-alive-timerLocal-dtes Peer-routers XTP Monitoring Commands Talk XTP Monitoring Commands Deletes a peer router from the XTP conguration Displays output of all list command optionsDeletelocal-dtes peer-router remote-dtes Deletes a local interface from the XTP conguration List of Peer Routers Displays all the interfaces congured for XTP Displays detailed information for all PVC denitions Displays all the remote interfaces congured for XTPPvc-detailed Pvcs-all-detailed Displays information for all the SVC denitions Svc-detailedDisplays information for specic SVC denitions Svcs-all-detailed 387 Using Frame Relay InterfacesEncryption in Using and Conguring Featuresfor details Frame Relay Overview Be allotted to the PVC whether or not the PVC uses it Using Frame RelayFrame Relay Network Management Frame Relay Interface Initialization Frame Relay Switched Virtual Circuits An orphan Orphan-circuit commandsOrphan Circuits For FR DTE to DTE connectivity is lost Orphan Circuit Enable switched-virtual-circuit command Frame Relay Frame Hdlc FlagsData Link Connection Identier Dlci Backward Explicit Congestion Notication Becn Command/Response C/RExtended Address Forward Explicit Congestion Notication Fecn Protocol Address Mapping Frame Forwarding over the Frame Relay NetworkProtocol Addresses Multicast Emulation and Protocol Broadcast Full Status Report Option on add switched-virtual-circuitFrame Relay Network Management Management Status Reporting Committed Information Rate CIR Link Integrity Verication ReportConsolidated Link Layer Management Cllm Frame Relay Data Rates Excess Burst Be Size Set CIR-defaults commandOrphan Permanent Virtual Circuit CIR Committed Burst Bc Size Line Speed Minimum Information RateMaximum Information Rate Variable Information Rate Circuit CongestionCIR Monitoring Congestion Notication and Avoidance Enable cir-monitor and disable cir-monitor console commandsCongestion-monitor console commands Congestion Monitoring Congestion Notication and Throttle Down Displaying the Frame Relay Conguration Prompt Frame Relay Basic Conguration ProcedureBandwidth Reservation in Using and Conguring Features Bandwidth Reservation over Frame Relay Frame Relay Management Options Example enable lmiCommand Options Description Enabling Frame Relay PVC Management Enabling Frame Relay SVC Management 405 Frame Relay Conguration CommandsConguring and Monitoring Frame Relay Interfaces Valid Values 16 to Committed Information Rate Conguring Frame Relay InterfacesPermanent-virtual-circuit Circuit Number Is the circuit required for operation What is the group nameExcess Burst Size Assign Circuit Name DN protocol AppleTalk Phase 2 protocolIP protocol IPX protocol Circuit Number or name Switched-virtual-circuitNode Number Node address Remote party subaddress Default Value E.164Remote party numbering plan Remote party number type Default Value Same as requested outgoing excess burst size Default Value Value of the requested outgoing CIRDefault Value Same as minimum acceptable outgoing CIR Default Value Value equal to requested outgoing Bc Is multicast required for this circuit Default Value yesEstablish circuit to learn remote protocol addresses Valid Values yes or no Permanent virtual circuit Congestion-monitor Cir-monitorCongured with theadd permanent-virtual-circuit or add Compression Notify-fecn-source Switched-virtual-circuitsMulticast-emulation No-pvc Change permanent-virtual-circuit command Previously disabled Frame Relay management Encryption enabled, will encrypt all transmitted dataEnables management activity Defaults to Ansi T1.617 Annex D management FR 1 Config enable switched Occurs between the router and the FR switch397 for information about the default CIR values Feature is enabled Local party number type Network emulation modeLocal party number Local party numbering plan Clocking Transmit delayEncoding Idle SVC network emulation mode LMI enabledCllm Enabled Timer Ty seconds Congestion Monitoring Timer T1 secondsProtocol Broadcast Emulate multicast Default Burst Size LMI N2 error thresholdLMI N3 error threshold window Default CIR Protocol Type Circuit TypePvc-groups Protocol-addresses Total SVCs congured OptionsRemote subaddress Permanent-virtual-circuit pvc# Set Command Considerations Example remove pvc-group PVC group name IP?Set n3-parameter 4 set n2-parameter Cir-defaults Default Value 64Physical Interface Link Type Data Connection Type Frame-size # Is the defaultValid Values See ªCommitted Burst Bc Sizeº on Clocking external or internal Ir-adjustmentincrement-% decrement-% minimum-IR Idle ¯ag or markLine-speed rate N2-parameter max# Transmit-delay #Lmi-type rev1 or ansi or ccitt N1-parameter count Ty-parameter time Accessing the Frame Relay Monitoring PromptFrame Relay Monitoring Commands Default Value 11 seconds Monitoring Frame Relay Interfaces Circuit is orphan List lmi and list permanent-virtual-circuit commandsCircuit name or number Circuit state Total Becns Frames/Bytes transmittedFrames/Bytes received Total Fecns Decryption errors Mode discardsCompression errors Encryption errors VC due to output queue over¯ow Management Status LMI enabledSerial device handler transmit queue for this interface Xmit frames dropped due to queue over¯ow Last Cllm cause code PVCs P1 allowedInterface down if no PVCs Current transmit sequence Default Excess CIRDECnet length eld Current receive sequence Active encryption circuits Data compression enabledData encryption enabled Active compression circuits Frames Transmitted Circuit#Orphan Circuit Type/State FR 1list virtual-circuits Virtual-circuitsCircuit# Circuitname Circuit circuit# or name cirvol bcval beval Information, see ªExcess Burst Be Sizeº on Required. The default setting is to trace all circuits Statistics Displayed For Frame Relay Interfaces Frame Relay Interfaces and the Gwcon Interface Command Circuit, Nicknames, and State Input frame errors Output aborts sent Monitoring Frame Relay Interfaces Using Point-to-Point Protocol Interfaces PPP Overview449 PPP Data Link Layer Frame Structure Using PPP PPP Link Control Protocol LCP Using PPP Data Option LCP PacketsIdentier Length Link Establishment Packets Link Maintenance Packets PPP Authentication ProtocolsLink Termination Packets Password Authentication Protocol PAP Challenge-Handshake Authentication Protocol Chap Microsoft PPP Chap Authentication MS-CHAPShiva Password Authentication Protocol Spap Conguring a PPP Interface to Authenticate a Remote Device Conguring PPP Authentication 459 Conguring PPP Callback PPP Network Control Protocols Using AAA with PPPExample 3 Roaming callback enabled Configadd PPP roamingcallback Callback Control Protocol AppleTalk Control ProtocolBanyan Vines Control Protocol Bridging Protocols IPv6 Control Protocol IP Control Protocol Appn HPR Control Protocol Using and Conguring Virtual ConnectionsIPX Control Protocol OSI Control Protocol Conguring a VC Commandsº in Using and Conguring Features Protocol Interfaces ªPoint-to-Point Conguration Commandsº onªPoint-to-Point Monitoring Commandsº on Conguring and Monitoring Point-to-Point Accessing the PPP Interface Conguration Prompt Point-to-Point Conguration CommandsConguring PPP Interfaces Talk Ecp CcpChap Dials Enables the use of data compression on the interface Enable chapEcp Stateless Mppe mandatory/optional stateless/statefulMandatory Optional Tinygram Compression Bcp Idle State Data Encryption Enabled/DisabledTransmit Delay Counter Algorithm List Example PPP 7 Conglist lcp Ipcp compressionSend Our IP Address Ipv6cp Cong Nak Tries Retry TimerAuthenticate remote using Cong Request Tries List ncp Ccp optionsCcp algorithms Name Stac # histories Stac check mode 0=none, 1=LCB, 2=CRC, 3=SeqNcp Bcp Sets the Bridging Control Protocol BCP parameters Ccp options Microsoft Point-to-Point Compression Mppc is used Algorithm in the listCompression. The valid compression algorithms are Hdlc idle ¯agor mark Hdlc cable cable typeHdlc clocking external or internal Hdlc encoding NRZ or Nrzi Receive clock lines. The range is 2400 to 2 048 000 bps Range is 0 to 15. The default isWhen determining the type of compression that is enabled. Range is 1 to 16. The default is Lcp options or parameters Maximum receive unitAsync Control Character Map Protocol Field Compression PFC Addr/Cntl Field Compression Acfc Transmitted. This is done to guard against packet loss Cong triesNAK tries Range is 1 to Remote Authenticationº in Using and Conguring Features LowercaseNcp parameters Point-to-Point Monitoring Commands Point-to-Point Monitoring Command Summary+ network 2 PPP Monitoring PPP Interfaces Talk Callback attempts Example list cbcpPackets Octets CCP state Example of the List Control ECP CommandExample for Mppc compression Denitions of Terms in the List Control CCP Example Local transmit encrypter Example of the List Control LCP CommandLink phase Time Since Change LCP State AuthenticateTerminate Link is being shut down Last Identication Rxd AuthenticationExample of the List Control BCP Command Remote Username Denitions of Terms in the List Control BCP Example Example of the List Control Nbcp CommandRemote NetBIOS Name Example of the List Control Nbfcp Command Denitions of Terms in the List Control Ipcp Example Example of the List Control Ipcp CommandDenitions of Terms in the List Control Nbfcp Example Remote Peer Leased IP address Example of the List Control Ipxcp CommandDhcp State Lease Server Local Node ID Example of the List Control Isrcp CommandHprcp Command Example Common Network Number Bad control Cong timeoutsTerminate timeouts Bad address List pap Monitoring PPP Interfaces Talk Successes/Failures RequestsChallenges Responses Failure Change Password Failure Account DisabledFailure Password Expired Failure Authentication Encrypted Octets Reset ReqsReset Acks Prot Rejects Dialbacks PleaseAuthenticates Mccp ACKs Change PasswordsMccp Call Reqs Mccp Callbacks Compression ratios Compressed octetsIncompressible packets Protocol rejects Brg StpNbcp Command. See ªipº List ip command. See ªipºCurrent IP connection List atcp List ipv6List ipxcp List ipx List bvcp List dnList osicp List osi List isr List hprcpList hpr Nicknames Interface NoAdapter cable Circuit Length of time since the port was reset Alignment byte lengthToo long 2048 bytes 509 Using the Multilink PPP Protocol MP Considerations Using MP Multi-Chassis MP Conguring a Multilink PPP InterfaceConguring MP on PPP Dial Circuits Single bundle Conguring MP on PPP Serial LinksConguring MP on Layer-2-Tunneling Nets Run on the MP interface and not the PPP dial circuits Hunt group Conguring Multi-Chassis MP Support LCP renegotiation 515 Accessing the MP Conguration PromptMP Conguration Commands for Multilink PPP Interfaces Conguring and Monitoring Multilink PPP Protocol MP Outbound calls EncapsulatorConguring MP Syntax Encapsulator Example Min fragment size BAP enabledDialout MP link net Max fragment size Add bandwidth % Default value inboundValid Values 0 to Default Value Mp parameters Valid Values 100 to 3 Default Value Monitoring MP Interface Status Accessing the MP Monitoring CommandsMultilink PPP Protocol Monitoring Commands Using add device multilink-ppp command PPP 6 list bacp Monitoring MPIndicates that the request is not supported Control bacp Callback Req Sent Control bodClosed Call Req Sent Seq order TimeoutControl mp Depth PPP 6 list mp MP Statistic Out Bytes Compressed 61230 60259 Monitoring MP Conguring Sdlc Relay Basic Conguration ProcedureAccessing the Sdlc Relay Conguration Environment Configprotocol sdlc Group number Sdlc Relay Conguration CommandsConguring and Monitoring Sdlc Relay Example add group IP address of remote router Interface numberPrimary or Secondary Remote±port Port List for network Srly Port Status List for protocol SdlcMaximum frame size in bytes Example list all Displays the conguration of a specied group Use the set command to congure the Srly parametersNet Number Indicates the IP address of the remote port Clocking internal or external Idle ¯agIdle mark Sdlc Relay Monitoring Commands Summary Accessing the Sdlc Relay Monitoring EnvironmentSdlc Relay Monitoring Commands Transmit-delay value Port interface# primary-or-secondary Syntax Enable Group PortClear-Port-Statistics Syntax Clear-port-statistics Packets fwrd and disc Enable portSyntax List All Group All Displays the congurations of all local ports List group Sdlc Relay Interfaces and the Gwcon Interface Command MRS V3.2 Software Users Guide Congure the dial circuit Using Sdlc InterfacesConguring Switched Sdlc Call-In Interfaces 537 Using Sdlc Interfaces Sdlc Conguration RequirementsCongure DLSw 539 Accessing the Sdlc Conguration EnvironmentConfigset data-link sdlc Conguring and Monitoring Sdlc Interfaces Enter station address Sdlc Conguration CommandsConguring Sdlc Interfaces Syntax Add Station Example Include station in group poll list Syntax Disable Link StationSyntax Enable Link Station Enter station name Link conguration DuplexModulo Interframe delay TimersInter-poll delay RTS hold delay Rx Window Poll retryStation all or address or link station name Max BTU Link encoding nrz or nrzi Link cable typeLink clocking internal or external Link duplex full or half Link idle mark Link inter-frame delay secondsLink group-poll Link idle ¯ag Link modulo 8 or Valid values 0 to Default value ExampleLink poll delay Link poll timeout Link speed Link snrm timeout or retryLink xid/test timeout or retry Link rts-hold Accessing the Sdlc Monitoring Environment + network Sdlc Monitoring CommandsSdlc Monitoring Commands Summary Syntax Add Station Station name or address or all Syntax disable linkSyntax clear Link Station Link name or address UI-Frames FramesBytes Re-Xmit Connected EnabledConnecting Recovering List station c1 counters List link countersList station all List station c1 Link role primary, secondary, or negotiable Link poll delay or timeout or retryLink snrme Link modulo Maximum size of packet that this station can receive Link type multipoint or point-to-point Number of test frames to send Sdlc Interfaces and the Gwcon Interface CommandStatistics Displayed for Sdlc Interfaces Teststation name or address #frames-to-send Frame-size Output frame counters Input frame errorsRS-232 Line speed congured Conguring Sdlc Interfaces Conguring Sdlc Interfaces Using Binary Synchronous Relay Brly Brly Overview561 IP address for the Primary BSC Devices local port is Sample Brly CongurationMultipoint connections . These examples use the following assumptions Group When conguring BRLY, keep the following in mind Brly ConsiderationsRemote Devices that disconnect frequently Reduce the total network throughput MRS V3.2 Software Users Guide BSC Relay Conguration Commands Conguring and Monitoring BSC Relay567 Local-port Default value multipointConguring and Monitoring BSC Relay Group type Remote group number Default value SStation Address Character Valid values X01 to XFF Default value local Local±port group#Local or Remote List for network BSC Remote Group List for protocol BrlyLink EOT Number of pairs of SYNs Code ebcdic or ascii Use the set command to congure the BSC interface parametersDisplays the conguration of a specied group Cable Eotlink yes or no Accessing the BSC Relay Monitoring EnvironmentDefault value yes Frame-size Default value mark Speed bps Syntax Clear Example BSC Relay Monitoring Commands Router, the effects of this command are erased Command are erasedRemote port Packets Discarded Local GroupStation Address Packets Forwarded Gwcon Talk 5 and Commands BSC Relay Interfaces and the Gwcon Interface Command Using the V.25bis Network Interface Adding V.25bis Addresses579 Conguring the V.25bis Interface Using V.25bisTimeout-no-answer commands Set command-delay-timeoutcommand species the amount of time Configadd device dial-circuit Adding Dial CircuitsConguring Dial Circuits Circuit Configset selftest-delay V.25bis conguration prompt now displays on the console 25bis Conguration CommandsConguring and Monitoring the V.25bis Network Interface 583 Non-responding addresses Retries 25bis Conguration CommandsLocal Network Address Name Local Network Address Connect-timeout # of seconds Call timeoutsCommand Delay Command-delay-timeout # of milliseconds Disconnect-timeout # of seconds Valid values NRZ or Nrzi Default value NRZ Hdlc speedHdlc encoding Local-address address name 25bis Monitoring CommandsAdd v25-bis-address command Timeout-no-answer # of seconds Site Name 25bis Operating CommandsCalls Syntax calls Example Circuits Syntax Statistics Example Call timeouts Command DelayNetwork address name of the local port Network dial address of the local port Transmit clock speed approximate Type of adapter cable being usedCircuit numbers as identied by V.24 specications Common names for the circuits Statistics for V.25bis Interfaces and Dial Circuits 25bis and the Gwcon Commands Vec Self-Test Passed Type of adapter cable that is being usedInterface CRC error Using the V.34 Network Interface Adding V.34 Addresses595 Optional V.34 Parameters UsingThese commands, see ªV.34 Conguration Commandsº on Conguring the V.34 Interface Using V.34 Circuit Configset selftest-delay Devices Conguring and Monitoring the V.34 Network Interface599 V.34 conguration prompt now displays on the console Conguring 34 Conguration Commands Summary Modem-init-string Command strings sent to the attached modemModem strings Initialization string Speed # bits per second Add v34-address command Modem-init-string value 34 Monitoring Command Summary Monitoring Function CommandNetwork address name of the dial circuit Circuits Example parameters Syntax Parameters CRC Statistics for V.34 Interfaces and Dial Circuits Example interface Nicknames Conguring 611 Using the Isdn InterfaceIsdn Overview Isdn Adapters and Interfaces Dial Circuits Using Isdn Addressing Oversubscribing and Circuit Contention Cost Control Over Demand Circuits Caller ID and LidsIsdn Cause Codes Code Cause Isdn Q.931 Cause Codes Sample Isdn Congurations Frame Relay over Isdn CongurationFollowing topics show several typical Isdn congurations Example of conguring a Channelized T1 interface Isdn Configset switch chanWAN Restoral Conguration Channelized T1/E1 7set timeslot 2 Switches/Services SupportedSwitch names Valid command Requirements and Restrictions for Isdn Interfaces Router Dial Circuit Conguration Requirements You cannot boot or dump the router over an Isdn interfaceSetting up and taking down B-channel connections Isdn Interface Restrictions Conguring Isdn Parameters Configadd isdn-addressIsdn Configset switch net5 Isdn Config set local-address-name D-channel. For example TEI number of your Isdn switchOptional Isdn Parameters Value from 0 to 63, assigned by your provider E1 PRI Interface Default is ANSI-T1.403 For exampleConguring the Isdn Interface T1/J1 PRI Interface Specify the timeout period for the circuit This section describes how to congure a dial circuitIsdn-address command. For example Use the set calls command. For example Prevent initial packets from being dropped. For example Using ªADD ISDN-ADDRESSº at thecong promptUse the encapsulator command. For example Which is the destination name by specifying a lidoutaddr Isdn I.430 and I.431 Switch Variants Native I.430 SupportNative I.431 Support Support Default value is none 627 Isdn Conguration CommandsConguring and Monitoring the Isdn Interface Block-Calls Isdn Conguration Commands Syntax Disable Ps1Syntax Enable Ps1 Framesize 1024 or 2048 or 4096 or Frame-type Default Value aDefault Values B8ZS Default Value Disabled Default Value None Example Default Value ANSI-T1.403 For E1 PRIDefault Value HDB3 Default ValueDisabled Local-address-name address name Default Value 180 seconds Service-prole-id B-channel# spid#Timeout-call-address # of seconds Timeout-call-address. It is xed at Tei auto or none or value Default Value DmspriDn0 directory number Dn1 directory number Cause Code Syntax Cause codeExample add FF Syntax cause code remove value Isdn Monitoring CommandsIsdn Monitoring Command Summary Monitoring Command Function Isdn Monitoring Commands ChannelsSyntax Channels Opr Req MAC/Data-LinkNnnData Rmt Disc Dial-dump L2CountersL3Counters Statistics Example for BRI usingSyntax statistics Example for BRI Example for PRI with E1 Example for Channelized T1 Example for PRI with T1 using Isdn and the Gwcon Commands Isdn and the Gwcon CommandsCircuits Be dropped and re-dialed Conguration Information on Router Hardware and Software Dial Circuit Conguration Commands Conguring and Monitoring Dial Circuits643 For Frame Relay, enter set data-link frame-relay Conguring Dial CircuitsNbound destination Inbound destination Variantsº on Be shown for all interface typesAny inbound Callback SelfTest Delay TimerBandwidth Base net Bandwidth kbps Anyinbound Destination addressname V34-address commandDefault value 7E Callback Yes or No Timeslot list of slots Lidused enabled or disabledSelftest-delay# of milliseconds Lidoutaddr addressname Dial Circuit Monitoring Commands CallbackSyntax Callback Appendix A. Quick Conguration Reference IPX DNA Conguring LAN Emulation Ethernet Conguring Interfaces Token-Ring Conguring Multilink PPP MP Interfaces Lidin Conguring Dial-Circuits Add another Dial Circuit Yes, No Yes No Next, the following prompt will be shown Be used for the duration of the connection Default is 30 minutes Dialoutserver Conguring Bridging Panel similar to the following is displayed Conguring Protocols Conguring IP Conguring IPX End stations Token-Ringor EthernetConguring IPX for Token-Ring Following prompt is displayed Ipxwan is enabled on any network interfaces Following prompts are displayedWhich to build a host number Conguring DECnet DNA Highest Node NumberRouter Level Highest Area DNA Configuration Saved Bootp Boot Tftp Boot IBD Boot Enabling Console Modem-ControlRestarting the Router Appendix A. Quick Conguration Reference MRS V3.2 Software Users Guide Appendix B. X.25 National Personalities GTE-Telenet675 MRS V3.2 Software Users Guide 677 Appendix C. Making a Router Load File from Multiple DisksAssembling a Load File Under DOS Assembling a Load File Under Unix Resulting le gw.ldc is the assembled router load Disassembling a Load File Under DOS Disassembling a Load File Under Unix # ls -la total# cutup gw.ldc gw # ls -la MRS V3.2 Software Users Guide 681 List of Abbreviations Cgwcon Fa-ga DoDDtype Eth Ifc# InARPKbps Mbps NetBIOSLSreq LSrxl Ring indicator routing information Network Service Access PointRandom access memory Ring error monitor Rxmt ROpconRtype Rxmits 251 252253 List of Abbreviations MRS V3.2 Software Users Guide 691 Glossary Advanced Peer-to-Peer Networking Appn network Advanced Peer-to-Peer Networking APPN. AnAdvanced Peer-to-Peer Networking Appn end Advanced Peer-to-Peer Networking Appn Glossary Carrier sense multiple access with collision Congestion. See network congestion Control point management services CPMS. aControl point management services unit CP-MSU Signal detector Rlsd Data circuit-terminating equipment DCE. In a data Digital Network Architecture DNA. The model for Explorer frame. See explorer packet Fragment. See fragmentation LevelGeneral data stream GDS. The data stream used for International Telecommunication Union ITU. Integrated services digital network ISDN. a digitalIntegrated Digital Network Exchange IDNX. a International Organization for Standardization Inverse Address Resolution Protocol InARP. Local management interface LMI protocol. In NCP Line switching. Synonym for circuit switchingLocal management interface LMI. See local Management interface LMI protocol Glossary MRS V3.2 Software Users Guide Open Systems Interconnection OSI reference Non-Return-to-Zero Changes-on-Ones Recording Switching Packet mode operation. Synonym for packet Ring. See ring network Rapid Transport Protocol RTP connection. Routing Table Maintenance Protocol RTMP. Simple Network Management Protocol SNMP. Synchronous Data Link Control Sdlc a Subnetwork Access Protocol SNAP. In LANs, aSubnet mask. Synonym for address mask Subnetwork mask. Synonym for address mask Glossary Transmission Control Protocol/Internet Protocol Character Wildcard character. Synonym for pattern-matching MRS V3.2 Software Users Guide 715 Index Numerics Binary synchronous communications relay Brly Chap Opcon DOS PAP SVC FRF Lter MRS V3.2 Software Users Guide Gwcon BUS List list MS-CHAP Ospf Config Gwcon Messages containing IP addresses 162 387 Technical support access Unix XTP Readers Comments Ð Wed Like to Hear from You How satised are you that the information in this book isPlease tell us how we can improve this book SC30-3681-08 Readers Comments Ð Wed Like to Hear from YouPage Ibmr IBM