bps. Also refer to 'adslAtucConfRateChanRatio' for information

 

 

 

regarding RADSL mode and refer to ATU-R transmit rate for

 

 

 

ATU-C receive rates.

 

 

 

 

 

 

Fast Max Tx Rate(bps)

Configured Maximum Transmit rate for 'Fast' channels, in bps.

 

 

 

 

 

Also refer to 'adslAtucConfRateChanRatio' for information

 

 

 

regarding RADSL mode and ATU-R transmit rate for ATU-C

 

 

 

receive rates.

 

 

 

 

 

 

Intl Max Tx Rate(bps)

Configured Maximum Transmit rate for 'Interleave' channels, in

 

 

 

 

 

bps. Also refer to 'adslAtucConfRateChanRatio' for information

 

 

 

regarding RADSL mode and ATU-R transmit rate for ATU-C

 

 

 

receive rates.

 

 

 

 

 

 

Max Intl Delay(ms)

Configured maximum Interleave Delay for this channel.

 

 

 

 

 

Interleave delay applies only to the interleave channel and defines

 

 

 

the mapping (relative spacing) between subsequent input bytes at

 

 

 

the interleaver input and their placement in the bit stream at the

 

 

 

interleaver output. Larger numbers provide greater separation

 

 

 

between consecutive input bytes in the output bit stream, allowing

 

 

 

for improved impulse noise immunity at the expense of payload

 

 

 

latency.

 

 

 

 

 

 

GsTxStartBin

The lowest bin number allowed for Tx signal.

 

 

 

 

 

 

 

 

GsTxEndBin

The highest bin number allowed for Tx signal.

 

 

 

 

 

 

 

 

GsRxStartBin

The lowest bin number allowed for Rx signal.

 

 

 

 

 

 

 

 

GsRxEndBin

The highest bin number allowed for Rx signal.

 

 

 

 

 

 

 

 

GsMaxBitsPerBin

The maximum Rx number of bits per bin.

 

 

 

 

 

 

 

 

GsMaxDCo

Maximum interleaving depth supported by the customer's

 

 

 

 

 

hardware

 

 

 

 

 

 

GsRxBinAdjust

This parameter employs Rx Start/End bin settings

 

 

 

 

 

 

 

 

GsAdi2x

For non-standard compliant ADI CPE

 

 

 

 

 

 

 

 

GsInitiate

Specifies which end initiates startup. It is also used to send a

 

 

 

 

 

C-tone to the remote unit.

 

 

 

 

 

 

GsTxPowerAtten

The value in dB of Tx power attenuation

 

 

 

 

 

 

 

 

GsCodingGain

Sets the coding gain in dB increments

 

 

 

 

 

 

 

 

GsRsFastOvrhdDown

This parameter sets the percentage overhead for the downstream

 

 

 

 

 

fast buffer. RS can also be disabled.

 

 

 

 

 

 

GsRsIntCorrectionDown

This parameter sets the correction time for the downstream

 

 

 

 

 

interleaved buffer.RS can also be disabled.

 

 

 

 

 

 

GsRsFastOvrhdUp

This parameter sets the percentage overhead for the upstream

 

 

 

 

 

fast buffer.RS can also be disabled.

 

 

 

 

 

 

GsDrStby

This parameter provides the ability to disable power to the line

 

 

 

 

 

driver

 

 

 

 

 

 

 

 

 

 

 

 

 

IP DSLAM

 

 

297