NEC 2400IMX B4 = 0, b5 = 0 2 ports, B4 = 1, b5 = 0 8 ports, FPC of the node providing IP

Models: 2400IMX

1 485
Download 485 pages 63.2 Kb
Page 359
Image 359

ASYDL: ASSIGNMENT OF SYSTEM DATA INTO LOCAL DM (LDM)

 

 

 

System Data (LDM) -1 Programming Sheet

 

 

 

 

 

 

 

SYSTEM

SYSTEM

DATA

BIT

 

 

CORRESPONDING

 

DATA

DATA

(DATA)

DATA

 

 

INDEX

 

SYSTEM DATA CONTENTS

TYPE

00 – FF

 

 

 

(INDEX)

 

 

 

 

DATA

 

 

 

(SYS)

(Hex)

 

BIT

 

512-1535

 

 

 

 

0/1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1

533

 

 

 

 

FPC of the node providing ACDP

 

 

 

 

 

 

 

 

 

 

1

 

b0

0/1 = Built-in IP, ACDP is not used/used Note 1

 

 

 

 

 

 

 

 

 

 

 

 

 

Output the system message (4-R) when TCP-IP connection

 

 

 

 

 

b1

is normally disconnected.

 

 

 

 

 

 

0/1 = Effective/Ineffective

 

 

 

 

 

 

 

 

 

 

 

 

b2

0/1 = “AGENT ANYWHERE” is out of service/in service

 

864

 

 

 

Note 2, Note 3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

b3

0/1 = “Multiple ACDPs” is not available/available Note 2

 

 

 

 

 

 

 

 

 

 

 

 

b4

Assign number of ports of Status Monitoring for terminal

 

 

 

 

 

 

(SMFN). Note 2, Note 4

 

 

 

 

 

 

1

 

 

 

 

b5

b4 = 0, b5 = 0 (2 ports)

 

 

 

 

b4 = 1, b5 = 0 (8 ports)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

FPC of the node providing IP.

 

 

 

 

 

 

(Assign 0 when the ACD service is activated in the self node

 

865

 

 

 

 

only.)

 

 

 

 

 

 

FPC: 1-253 (01 Hex – FD Hex)

 

 

 

 

 

 

Note 5, Note 6

 

 

 

 

 

 

 

 

 

 

 

 

 

FPC of the node providing ACDP

 

 

 

 

 

 

(Assign 0 when the ACD service is activated in the self node

 

866

 

 

 

 

only.)

 

 

 

 

 

 

FPC: 1-253 (01 Hex – FD Hex)

 

 

 

 

 

 

Note 5, Note 6

 

 

 

 

 

 

 

Note 1: For ACD system to be activated through Fusion network, this data is programmed in the node providing ACDP only. Other data must be set to all nodes within Fusion network.

Note 2: Available since the PBX software Series 7400 and the ACD software R3.

Note 3: This data is used in the network providing multiple ACDPs.

Note 4: The identical data value must be assigned to all nodes.

Note 5: This data is necessary at all nodes. Assign the self FPC at the terminating node.

Note 6: For ACD service provided within Fusion network, the data value (FPC) in these indexes must be pro- grammed the same.

CHAPTER 7

NDA-24282

Page 340

Revision 1.0

Page 359
Image 359
NEC 2400IMX system manual B4 = 0, b5 = 0 2 ports, B4 = 1, b5 = 0 8 ports, FPC of the node providing IP