Issue 01/06 | Parameters |
2.3Command and Drive Datasets - Overview
Command Datasets (CDS)
ParNo | Parameter text | 1) |
P0700[3] | Selection of command source | X |
P0701[3] | Function of digital input 1 | X |
|
|
|
P0702[3] | Function of digital input 2 | X |
|
|
|
P0703[3] | Function of digital input 3 | X |
|
|
|
P0704[3] | Function of digital input 4 | X |
|
|
|
P0705[3] | Function of digital input 5 | X |
|
|
|
P0706[3] | Function of digital input 6 | X |
P0707[3] | Function of digital input 7 | X |
|
|
|
P0708[3] | Function of digital input 8 | X |
|
|
|
P0719[3] | Selection of cmd. & freq. setp. | X |
|
|
|
|
|
|
P0731[3] | BI: Function of digital output 1 | X |
|
|
|
P0732[3] | BI: Function of digital output 2 | X |
|
|
|
P0733[3] | BI: Function of digital output 3 | X |
|
|
|
P0800[3] | BI: Download parameter set 0 | – |
P0801[3] | BI: Download parameter set 1 | – |
|
|
|
|
|
|
P0840[3] | BI: ON/OFF1 | X |
|
|
|
P0842[3] | BI: ON reverse/OFF1 | X |
P0844[3] | BI: 1. OFF2 | X |
|
|
|
P0845[3] | BI: 2. OFF2 | X |
|
|
|
P0848[3] | BI: 1. OFF3 | X |
|
|
|
P0849[3] | BI: 2. OFF3 | X |
|
|
|
P0852[3] | BI: Pulse enable | X |
|
|
|
P1000[3] | Selection of frequency setpoint | X |
P1020[3] | BI: Fixed freq. selection Bit 0 | X |
|
|
|
P1021[3] | BI: Fixed freq. selection Bit 1 | X |
|
|
|
|
|
|
P1022[3] | BI: Fixed freq. selection Bit 2 | X |
P1023[3] | BI: Fixed freq. selection Bit 3 | X |
|
|
|
P1026[3] | BI: Fixed freq. selection Bit 4 | X |
|
|
|
P1028[3] | BI: Fixed freq. selection Bit 5 | X |
|
|
|
P1035[3] | BI: Enable MOP | X |
|
|
|
P1036[3] | BI: Enable MOP | X |
|
|
|
P1055[3] | BI: Enable JOG right | X |
P1056[3] | BI: Enable JOG left | X |
|
|
|
P1070[3] | CI: Main setpoint | X |
|
|
|
P1071[3] | CI: Main setpoint scaling | X |
|
|
|
ParNo | Parameter text | 1) |
P1074[3] | BI: Disable additional setpoint | X |
P1075[3] | CI: Additional setpoint | X |
|
|
|
P1076[3] | CI: Additional setpoint scaling | X |
|
|
|
P1110[3] | BI: Inhibit neg. freq. setpoint | X |
|
|
|
P1113[3] | BI: Reverse | X |
|
|
|
P1124[3] | BI: Enable JOG ramp times | X |
|
|
|
P1140[3] | BI: RFG enable | X |
P1141[3] | BI: RFG start | X |
|
|
|
P1142[3] | BI: RFG enable setpoint | X |
|
|
|
P1230[3] | BI: Enable DC braking | X |
|
|
|
|
|
|
P1330[3] | CI: Voltage setpoint | X |
|
|
|
P1477[3] | BI: Set integrator of | X |
|
|
|
P1478[3] | CI: Set integrator value | X |
|
|
|
P1500[3] | Selection of torque setpoint | X |
P1501[3] | BI: Change to torque control | X |
|
|
|
|
|
|
P1503[3] | CI: Torque setpoint | X |
|
|
|
P1511[3] | CI: Additional torque setpoint | X |
P1522[3] | CI: Upper torque limit | – |
|
|
|
P1523[3] | CI: Lower torque limit | – |
|
|
|
P2103[3] | BI: 1. Faults acknowledgement | X |
|
|
|
P2104[3] | BI: 2. Faults acknowledgement | X |
|
|
|
P2106[3] | BI: External fault | X |
|
|
|
P2200[3] | BI: Enable PID controller | – |
P2220[3] | BI: Fixed PID setp. select Bit 0 | X |
|
|
|
P2221[3] | BI: Fixed PID setp. select Bit 1 | X |
|
|
|
|
|
|
P2222[3] | BI: Fixed PID setp. select Bit 2 | X |
P2223[3] | BI: Fixed PID setp. select Bit 3 | X |
|
|
|
P2226[3] | BI: Fixed PID setp. select Bit 4 | X |
|
|
|
P2228[3] | BI: Fixed PID setp. select Bit 5 | X |
|
|
|
P2235[3] | BI: Enable | X |
|
|
|
P2236[3] | BI: Enable | X |
|
|
|
P2253[3] | CI: PID setpoint | X |
P2254[3] | CI: PID trim source | X |
|
|
|
P2264[3] | CI: PID feedback | X |
|
|
|
1)X = Parameters will be altered during data set switchover (CDS) in the state "Run"
–= Parameters will be altered in the state "Ready" only
MICROMASTER 440 | Parameter List |
17 |
