Issue 01/06 | Parameter Description |
3.29.2.4Torque control
P1500[3] Selection of torque setpoint |
| Min: | 0 | ||
CStat: | CT | Datatype: U16 | Unit: - | Def: | 0 |
CONTROL | Active: first confirm | QuickComm.: Yes | Max: | 77 | |
Level
2
Selects torque setpoint source. In the table of possible settings below, the main setpoint is selected from the least significant digit (i.e., 0 to 7) and any additional setpoint from the most significant digit (i.e., x0 through to x7).
Possible Settings:
0No main setpoint
2Analog setpoint
4USS on BOP link
5USS on COM link
6CB on COM link
7Analog setpoint 2
20 | No main setpoint | + | Analog setpoint |
22 | Analog setpoint | + | Analog setpoint |
24 | USS on BOP link | + Analog setpoint | |
25 | USS on COM link | + Analog setpoint | |
26 | CB on COM link | + Analog setpoint | |
27 | Analog setpoint 2 | + | Analog setpoint |
40 | No main setpoint | + USS on BOP link | |
42 | Analog setpoint | + USS on BOP link | |
44 | USS on BOP link | + USS on BOP link | |
45 | USS on COM link | + USS on BOP link | |
46 | CB on COM link | + USS on BOP link | |
47 | Analog setpoint 2 | + USS on BOP link | |
50 | No main setpoint | + USS on COM link | |
52 | Analog setpoint | + USS on COM link | |
54 | USS on BOP link | + USS on COM link | |
55 | USS on COM link | + USS on COM link | |
57 | Analog setpoint 2 | + USS on COM link | |
60 | No main setpoint | + CB on COM link | |
62 | Analog setpoint | + CB on COM link | |
64 | USS on BOP link | + CB on COM link | |
66 | CB on COM link | + CB on COM link | |
67 | Analog setpoint 2 | + CB on COM link | |
70 | No main setpoint | + | Analog setpoint 2 |
72 | Analog setpoint | + | Analog setpoint 2 |
74 | USS on BOP link | + Analog setpoint 2 | |
75 | USS on COM link | + Analog setpoint 2 | |
76 | CB on COM link | + Analog setpoint 2 | |
77 | Analog setpoint 2 | + | Analog setpoint 2 |
Index:
P1500[0] : 1st. Command data set (CDS)
P1500[1] : 2nd. Command data set (CDS)
P1500[2] : 3rd. Command data set (CDS)
Example:
Setting 24 selects the main setpoint (4) derived from the USS on BOP link with the additional setpoint (2) derived from the analog input. Single digits are main setpoints only with no additional setpoint.
Example P1500 = 24 :
P1500 = 24 ⇒ | P1503 | = 755.0 | P1503 CI: Torque setpoint | ||
r0755 | CO: Act. ADC after scal. [4000h] | ||||
|
|
| |||
|
|
|
| ||
P1500 = 24 ⇒ | P1511 | = r2015.1 | P1511 CI: Additional torque setpoint | ||
|
| ||||
r2015 | CO: PZD from BOP link (USS) | ||||
|
|
| |||
|
|
|
|
| |
ADC |
| |
USS |
| |
BOP link |
| |
USS | P1000 = 24 | |
COM link |
| |
CB |
| |
COM link | P1000 = 24 | |
ADC2 | ||
| ||
MICROMASTER 440 Parameter List |
| |
|
Additonal torque setpoint
Torque setpoint
Sequence control
Torque control
