Issue 01/06 | Parameter Description |
P1825 |
|
| Min: | 0.0 | ||
| CStat: | CUT | Datatype: Float | Unit: V | Def: | 1.4 |
| INVERTER | Active: Immediately | QuickComm.: No | Max: | 20.0 | |
Corrects
Level
4
P1828 | Gating unit dead time |
|
| Min: | 0.00 | |
| CStat: | CUT | Datatype: Float | Unit: us | Def: | 0.50 |
| INVERTER | Active: first confirm | QuickComm.: No | Max: | 3.50 | |
Sets compensation time of gating unit interlock.
Level
4
3.31Motor data identification
P1909[3] Ctrl. word of motor data ident. |
| Min: | 0 | ||
CStat: | CUT | Datatype: U16 | Unit: - | Def: | 1 |
CONTROL | Active: first confirm | QuickComm.: No | Max: | 1 | |
Control word of motor data identification.
Bitfields:
Level
4
Bit00 | Estimation of Xs | 0 NO | 1 YES |
Index: |
|
|
|
P1909[0] | : 1st. Drive data set (DDS) |
|
|
P1909[1] | : 2nd. Drive data set (DDS) |
|
|
P1909[2] | : 3rd. Drive data set (DDS) |
|
|
P1910 | Select motor data identification |
| Min: | 0 | Level | ||
| CStat: | CT | Datatype: U16 | Unit: - | Def: | 0 | 2 |
|
| ||||||
| MOTOR | Active: first confirm | QuickComm.: Yes | Max: | 20 |
| |
Performs a motor data identification.
Possible Settings:
0Disabled
1Identification of all parameters with parameter change
2Identification of all parameters without parameter change
3Identification of saturation curve with parameter change
4Identification of saturation curve without parameter change
5Identification of XsigDyn (r1920) without parameter change
6Identification of Tdead (r1926) without parameter change
7Identification of Rs (r1912 ) without parameter change
8Identification of Xs (r1915) without parameter change
9Identification of Tr (r1913) without parameter change
10Identification of Xsigma (r1914) without parameter change
20Set voltage vector
Common Settings:
P1910 = 1:
All motor data and inverter characteristic will be identified and parameter will be changed.
-P0350 stator resistance,
-P0354 rotor resistance,
-P0356 stator leakage inductance,
-P0358 rotor leakage inductance,
-P0360 main inductance
-P1825
-P1828 compensation time of gating unit interlock
P1910 = 3:
Saturation curve will be identified and parameter will be changed.
-P0362 ... P0365 magnetizing curve flux 1 .. 4
-P0366 ... P0369 magnetizing curve imag 1 .. 4
Caution:
Motor identification should normally be performed on a cold motor. However, the identification of the motor data should only be performed if the motor temperature is within 5°C of the measured ambient temperature stored in P0625. If the motor identification is not within the 5ºC limit then the correct functioning of Vector Control (VC, SLVC) cannot be guaranteed. This may cause instabilities when using vector control.
The motor rating plate information with respect to the connection of the motor windings (Star or delta connection) must be correct in order to establish the correct equivalent circuit data. The motor identification calculates this data based on a Phase of a Star equivalent circuit P0350 - P0360, irrespective of whether the motor is connected star or delta. This must be considered when the motor data is input directly.
Note:
-In order to that the motor identification routine supplies the correct data, before selecting, fast commissioning should be
-If the motor data identification routine is activated (e.g. P1910 = 1), then at the next ON command, the measuring operation is started and alarm A0541 is generated. After the measurement is completed, both P1910 and the alarm are reset.
MICROMASTER 440 | Parameter List |
189 |
