Omron FQM1-MMP21, FQM1-CM001, FQM1-MMA21 Auxiliary Area Allocations, Appendix D, A612

Auxiliary Area Allocations				Appendix D
Address	Bits		Name	Function
A612	00 to 15	High-	Range Comparison Execution	Contains the CTBL(882) execution results for range comparison.
		speed	Results Flags	Bits 00 to 15 correspond to ranges 1 to 16.
		counter 1		OFF: No match
		monitor		ON: Match
		data
A613	00 to 15		Output Bit Pattern	Contains the output bit pattern when a match is found for
				CTBL(882) execution results for range comparison
				Note If more than one match is found, an OR of the output bit
				patterns with matches will be stored here.
A614	00 to 15	High-	Range Comparison Results	Same as for high-speed counter 1 monitor data.
		speed
A615	00 to 15		Output Bit Pattern
		counter 2
		monitor
		data
A620 to	00 to 15	Pulse Output 1 PV		Contains the pulse output PV as an 8-digit hexadecimal number.
A621		Note This item applies when the operation		Relative mode: 00000000 to FFFFFFFF hex
		mode is relative pulse output, absolute pulse		Absolute linear mode: 80000000 to 7FFFFFFF hex
		output in linear mode, absolute pulse output in		Absolute circular mode: 00000000 to circular maximum count
		circular mode, or electronic cam mode.
		One-shot Pulse Output 1 ON Time		Contains the time that the one-shot pulse output has been ON as
		Note This item applies when the operation		an 8-digit hexadecimal number.
				0000 0000 to 0000 270F (unit: set by STIM(980))
		mode is one-shot output mode.
		Pulse Time Measurement 1		Contains the time measured by the pulse counter as an 8-digit
		Note This item applies when the operation		hexadecimal number.
				0000 0000 to FFFF FFFF hex (unit: set by STIM(980))
		mode is time measurement mode using a pulse
		counter.
A622 to	00 to 15	Pulse Output 2 PV		Same as for Pulse Output 1 PV.
A623
		One-shot Pulse Output 2 ON Time		Same as for One-shot Pulse Output 1 ON time.
		Pulse Time Measurement 2		Same as for Pulse Time Measurement 1.
A624	00	Pulse	Pulse Output Completed Flag	OFF: Pulse output not completed (OFF during pulse output).
		Output 1		ON: Pulse output completed (ON when pulse distribution has
		Status		been completed).
	01		Pulse Output Set Flag	OFF: Pulse output amount not set by PULS(886).
				ON: Pulse output amount set by PULS(886).
	02		Target Frequency Not Reached Flag	OFF: Target speed has been reached during pulse output for
				PLS2(887).
				ON: Decelerated before reaching the target speed during pulse
				output for PLS2(887).
	03		Target Comparison Flag	OFF: Comparison stopped.
				ON: Comparison in progress.
	04		Independent Pulse Output Flag	OFF: Pulses not being output or being output continuously.
				ON: Pulses being output.
	05		PLS2 Positioning Flag	OFF: Not positioning.
				ON: Positioning in progress.
	06		Accelerating/Decelerating Flag	OFF: No output or constant-speed output.
				ON: Acceleration or deceleration in progress for ACC(888) or
				PLS2(887).
	07		Pulse Output Flag	OFF: Pulse output stopped.
				ON: Pulse output in progress.
A625	00	Pulse	Pulse Output Completed Flag	Same as for Pulse Output 1 Status.
		Output 2
	01		Pulse Output Set Flag
		Status
	02		Target Frequency Not Reached Flag
	03		Target Comparison Flag
	04		Independent Pulse Output Flag
	05		PLS2 Positioning Flag
	06		Accelerating/Decelerating Flag
	07		Pulse Output Flag

357