Omron FQM1-MMA21, FQM1-CM001, FQM1-MMP21 operation manual Connecting the CX-Programmer, Section

Models: FQM1-MMP21 FQM1-MMA21 FQM1-CM001

1 414
Download 414 pages 44.52 Kb
Page 262
Image 262
Connecting an RS-232C Cable to the RS-232C Port

Connecting the CX-Programmer

 

 

 

 

 

 

 

 

 

Section 8-2

 

 

 

 

 

 

Connecting an RS-232C Cable to the Peripheral Port

 

 

 

 

 

 

 

 

The following connection configurations can be used when connecting an RS-

 

 

 

 

 

 

232C cable to the Coordinator Module’s peripheral port.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Port on

 

Computer

Port on

Communications mode

 

 

Model

Length

 

Remarks

Module

 

 

 

computer

 

(Network type)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Built-in

 

Windows

D-Sub 9-pin

Peripheral bus (Tool bus)

 

CS1W-CN118 +

0.1 m +

The XW2Z-@@@S-CV

peripheral

 

OS

male

or Host Link (SYSMAC

 

XW2Z-200S-CV/

(2 m or

Cables have static-

port

 

 

 

 

 

 

WAY)

 

 

500S-CV

5 m)

 

resistant connectors.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Host link (SYSMAC WAY)

 

CS1W-CN118 +

 

 

---

 

 

 

 

 

 

 

 

 

 

 

 

 

XW2Z-200S-V/

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

500S-V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting an RS-232C Cable to the RS-232C Port

 

 

 

 

 

 

 

 

The following connection configuration can be used to connect a personal

 

 

 

 

 

 

computer to the Coordinator Module’s RS-232C port with an RS-232C cable.

 

 

 

 

 

 

 

 

 

 

 

 

Port on

 

Computer

Port on

 

Communications mode

Model

 

Length

Remarks

Module

 

 

 

computer

 

(Network type)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Built-in RS-

 

Windows OS

D-Sub 9-pin

 

Host link (SYSMAC WAY)

XW2Z-200S-V

2 m

 

---

232C port D-

 

 

 

male

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

XW2Z-500S-V

5 m

 

 

sub 9-pin

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

female

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note Either one of the following two serial communications modes can be used

 

 

 

 

 

 

when connecting the CX-Programmer to the FQM1.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Serial

 

 

 

Features

 

 

 

 

 

 

 

 

communications

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

mode

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Peripheral bus

Supports high-speed communications, so this communications

 

 

 

 

 

 

(Tool bus)

mode is normally used to connect to the CX-Programmer.

 

 

 

 

 

 

 

 

 

 

• Supports only a 1:1 connection.

 

 

 

 

 

 

 

 

 

 

 

 

 

• When the FQM1 is connected, the CX-Programmer can recog-

 

 

 

 

 

 

 

 

 

 

nize the baud rate and make the connection automatically.

 

 

 

 

 

 

Host link (SYS-

This communications mode is generally used to connect to a

 

 

 

 

 

 

MAC WAY)

host computer. Both 1:1 and 1:N connections are supported.

 

 

 

 

 

 

 

 

 

 

• Host link communications are relatively slow compared to the

 

 

 

 

 

 

 

 

 

 

peripheral bus mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• The Host Link mode supports connections through modems or

 

 

 

 

 

 

 

 

 

 

optical adapters, long-distance connections using RS-422A or

 

 

 

 

 

 

 

 

 

 

RS-485 communications, and 1:N connections.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

239

Page 262
Image 262
Omron FQM1-MMA21, FQM1-CM001 Connecting the CX-Programmer, Section, Connecting an RS-232CCable to the RS-232CPort