Omron FQM1-CM001, FQM1-MMA21, FQM1-MMP21 Auxiliary Area Allocations, Appendix D, A520

Auxiliary Area Allocations				Appendix D
Address	Bits	Name		Function
A520	00 to 15	Interrupt Counter 0 Counter SV	Used for interrupt input 0 in counter mode.
			Sets the count value at which the interrupt task will start. Interrupt
			task 000 will start when interrupt counter 0 has counted this num-
			ber of pulses.
			Setting range: 0000 to FFFF
A521	00 to 15	Interrupt Counter 1 Counter SV	Used for interrupt input 1 in counter mode.
			Sets the count value at which the interrupt task will start. Interrupt
			task 001 will start when interrupt counter 1 has counted this num-
			ber of pulses.
			Setting range: 0000 to FFFF
A522	00 to 15	Interrupt Counter 2 Counter SV	Used for interrupt input 2 in counter mode.
			Sets the count value at which the interrupt task will start. Interrupt
			task 002 will start when interrupt counter 2 has counted this num-
			ber of pulses.
			Setting range: 0000 to FFFF
A523	00 to 15	Interrupt Counter 3 Counter SV	Used for interrupt input 3 in counter mode.
			Sets the count value at which the interrupt task will start. Interrupt
			task 003 will start when interrupt counter 3 has counted this num-
			ber of pulses.
			Setting range: 0000 to FFFF
A524	00 to 15	Interrupt Counter 0 Counter PV	These words contain the interrupt counter PVs for interrupt input
			0 to 3 operating in counter mode.
A525	00 to 15	Interrupt Counter 1 Counter PV
			The counter PV starts decrementing from the counter SV. When
A526	00 to 15	Interrupt Counter 2 Counter PV
			the counter PV reaches the 0, the PV is automatically reset to the
			SV.
A527	00 to 15	Interrupt Counter 3 Counter PV
			Range: 0000 to FFFF
A530	00	DM Write Request Bit (Coordinator Module to	DM data transfer is executed from the Coordinator Module to
		Motion Control Module)	Motion Control Module when this bit turns ON.
	01	DM Read Request Bit (Motion Control Module to	DM data transfer is executed from the Motion Control Module to
		Coordinator Module)	Coordinator Module when this bit turns ON.
A531	00 to 15	Slot No. of Motion Control Module for DM Trans-	Specifies the slot number (in 4-digit hexadecimal) for the Motion
		fer	Control Module with which DM data is to be transferred.
			0001: Motion Control Module #1
			0002: Motion Control Module #2
			0003: Motion Control Module #3
			0004: Motion Control Module #4
A532	00 to 15	DM Transfer Size (number of words)	Specifies the size, in number of words, of the DM data to be trans-
			ferred.
			0001 to 01F3 hex (1 to 499 words)
A533	00 to 15	First DM Transfer Source Word	Specifies the first address of the DM transfer source in the Coor-
			dinator Module or Motion Control Module.
			0000 to 7FFF hex
A534	00 to 15	First DM Transfer Destination Word	Specifies the first address of the DM transfer destination in the
			Coordinator Module or Motion Control Module.
			0000 to 7FFF hex
A535	14	Transfer Error Flag	Turns ON when a DM data transfer error occurs.
	15	Transfer Busy Flag	Turns ON during DM data transfer and turns OFF when the trans-
			fer has been completed.
A550	00 to 15	Analog Input PV	Contains the value input from the analog input port (using either
			the END refresh or immediate refresh) in 4-digit hexadecimal.
			The PV range depends on the input range:
			• 0 to 10 V:	FE70 to 20D0 hex
			• 0 to 5 V or 1 to 5 V:	FF38 to 1068 hex
			• −10 to 10 V:	DDA0 to 2260 hex
A552	00	Analog Input Status	User Adjustment	OFF: Not adjusted
			Completed	ON: Adjustment completed
	07		Analog Sampling	OFF: Not started
			Started	ON: Started
	08		Factory Adjustment	OFF: No Error
			Data Error	ON: Error (Checked at power ON.)
	09		User Adjustment	OFF: No Error
			Data Error	ON: Error (Checked at power ON.)
	15		Analog Sampling	OFF: Normal sampling
			Overlap	ON: The next sampling operation occurred
				before the present sampling operation com-
				pleted.

352