Omron FQM1-MMA21, FQM1-CM001, FQM1-MMP21 Auxiliary Area Allocations, Appendix D, A559

Auxiliary Area Allocations				Appendix D
Address	Bits	Name		Function
A559	00 to 15	Number of Analog Samples		Indicates the number of data samples actually input since sam-
				pling started.
A560	00 to 15	Analog Output 1 Output Value		When an END refresh is selected, the 4-digit hexadecimal value
				set here by the user is output from analog output port 1.
				When immediate refreshing is selected, the 4-digit hexadecimal
				value being output from analog output port 1 is stored here for
				monitoring. The output value range depends on the output range,
				as shown below.
				• 0 to 10 V, 0 to 5 V or 1 to 5 V: FF38 to 1068 hex
				• −10 to 10 V: EA84 to 157C hex
				Note
				1. Set the analog output method (END or immediate refreshing)
				with the System Setup’s output method setting. A setting of 0
				hex specifies an END refresh. This setting applies to both ana-
				log output 1 and 2.
				2. Specify the output range with the output 1 setting.
A561	00 to 15	Analog Output 2 Output Value		This word has the same settings as the analog output 1 output
				value (A560), above. (When an END refresh is selected, set the
				value to output from analog output port 2. When an immediate
				refresh is selected, the output value is stored here for monitoring.)
				Note
				1. Set the analog output method (END or immediate refresh) with
				the System Setup’s output method setting. A setting of 0 hex
				specifies an END refresh. This setting applies to both analog
				output 1 and 2.
				2. Specify the output range with the output 2 setting.
A562	00	Analog Output 1 Flags	User Adjustment	Initial value is 0.
			Completed	Set to 1 if user performs offset/gain adjustment and Returns to
				factory default setting of 0 if adjustment value is cleared.
	04		Operating	ON: ON while the analog output is being changed by ACC(888).
				OFF: Turned OFF when target value is reached.
	08		Output SV Error	ON: ON when the output SV setting is outside of the allowed set-
				ting range.
				OFF: OFF when the output SV is within range.
	12		Factory Adjust-	ON: ON when the factory-set data stored in flash memory is
			ment Value	invalid.
			Error	OFF: OFF when the factory-set data stored in flash memory is
				normal.
	14		User Adjustment	ON: ON when the user-set adjustment value stored in flash mem-
			Value Error	ory is invalid.
				OFF: OFF when the user-set adjustment value stored in flash
				memory is normal.
A563	00	Analog Output 2 Flags	User Adjustment	Same as for Analog Output 1 Flags.
			Completed
	04		Operating
	08		Output SV Error
	12		Factory Adjust-
			ment Value
			Error
	14		User Adjustment
			Value Error
A564	00	Analog Output 1 Conversion Enable Bit		ON: Enables D/A conversion (enables analog output).
				OFF: Disables D/A conversion (analog values output according to
				Output Stop Function specification in System Setup).
				Note This bit is cleared when the Modules operating mode is
				changed between RUN or MONITOR mode and PROGRAM
				mode.
A565	00	Analog Output 2 Conversion Enable Bit		ON: Enables D/A conversion (enables analog output).
				OFF: Disables D/A conversion (analog values output according to
				Output Stop Function specification in System Setup).
				Note This bit is cleared when the Modules operating mode is
				changed between RUN or MONITOR mode and PROGRAM
				mode.

353