Omron FQM1-MMA21, FQM1-CM001, FQM1-MMP21 operation manual Appendix C, A564

System Setup, Auxiliary Area Allocations, and Built-in I/O Allocations							Appendix C
Address	Bits	Name			Function			Controlled by
A564	00	Analog Output 1	Conversion Enable	ON: Enables D/A conversion (enables analog output).				User
			Bit	OFF: Disables DA conversion (analog values output
				according to Output Stop Function specification in Sys-
				tem Setup).
				Note This bit is cleared when the Modules operating
				mode is changed between RUN or MONITOR mode
				and PROGRAM mode.
	01 to 15	Reserved		---				---
A565	00	Analog Output 2	Conversion Enable	ON: Enables D/A conversion (enables analog output).				User
			Bit	OFF: Disables DA conversion (analog values output
				according to Output Stop Function specification in Sys-
				tem Setup).
				Note This bit is cleared when the Modules operating
				mode is changed between RUN or MONITOR mode
				and PROGRAM mode.
	01 to 15	Reserved		---				---
A570	00	Adjustment Mode	Adjustment Enable	Analog Input	OFF: Adjustment disabled.			User
		Command Bits			ON: Adjustment enabled.
	01			Reserved
		(Effective only			When one of these bits is turned ON,
	02			Analog Out-
		when A575 is			the default value (offset or gain value)
		5A5A hex.)		put 1	corresponding to the selected I/O signal
	03			Analog Out-	range is transferred to Adjustment
					Mode Monitor Area (A572 and A573).
				put 2
	04 to 06		Reserved
	07		Adjustment Mode	OFF: Offset adjustment
			Specifier	ON: Gain adjustment
	08 to 11		Reserved
	12		Adjustment Value	While this bit is ON, the offset or gain value will be
			Increment	incremented by one resolution unit each 0.5 ms.
	13		Adjustment Value	While this bit is ON, the offset or gain value will be dec-
			Decrement	remented by one resolution unit each 0.5 ms.
	14		Adjustment Value	OFF to ON: Clears the adjustment data to the factory
			Clear	defaults.
	15		Adjustment Value	OFF to ON: Reads the present value in the Adjustment
			Set	Mode Monitor Area (A572 and A573) and saves this
				value to flash memory. This adjustment value will be
				used for the next normal mode operation.
A571	00	Adjustment Mode	Adjustment Opera-	ON when an operational error has been made, such as				Module
		Status	tion Error	turning ON both the Analog Input and Analog Output 2
				Adjustment Enable Bits at the same time.
	01 to 14		Reserved
	15		Adjustment Mode	ON during adjustment mode operation (when A575
			Started	contains 5A5A hex).
A572	00 to 15	Adjustment Mode	Both Analog Input	Setting Off-	The values in	• −10 to 10 V: FE0C to		Module/User
		Monitor	and Analog Out-	set Monitor	these words	01F4 hex
		(Effective only	puts		can be over-	• 0 to 10 V, 0 to 5 V, 1 to
		when A575 is			written	5 V: FF38 to 00C8 hex
		5A5A hex.)			directly, with-
A573	00 to 15			Gain Value		• −10 to 10 V: 1194 to
					out using the
				Monitor		157C hex
					Adjustment
						• 0 to 10 V, 0 to 5 V, 1 to
					Value Incre-
					ment/Decre-	5 V: 0ED8 to 1068 hex
					ment Bits.
A574	00 to 15		Analog Inputs	Number of	Indicates the number of values to be			User
				Average	averaged to obtain the Offset/Gain
				Value Sam-	Value Monitor values in adjustment
				ples in Adjust-	mode. The number of samples can be
				ment Mode	set between 0000 and 0040 hex (0 to
					64). Set this parameter before turning
					ON the Adjustment Enable Bit.
A575	00 to 15	Adjustment Mode Password		5A5A hex: Adjustment mode enabled.				User
				Other value: Adjustment mode disabled.

338