Show interface stats | Carrier Access none manual

User Mode

show interface stats

Use the show interface stats command to display the interface statistics.

Syntax: > show interface stats

Example: Adit 3500> show interface stats

Device=T1 1	State=up		Dependency=None	Status: Connecting (Alarm Condition)
Device=T1 2	State=up		Dependency=None	Status: Connecting (Alarm Condition)
Device=T1 3	State=running		Dependency=None	Status: Connected
Device=T1 4	State=running		Dependency=None	Status: Connected
Device=Serial 1	State=down	IP/Mask=0.0.0.0/255.255.255.255	Dependency=T1 1	Status: Disconnected
Device=Ethernet 2	State=disabled	IP/Mask=192.168.2.10/255.255.255.0	Dependency=None
Device=Ethernet 1	State=running	IP/Mask=192.168.1.35/255.255.255.0	Dependency=None	Status: Connected; Link: 10T-HD
	Tx (Packets/Bytes/Dropped/Errors)=(2362/2498024/0/0)
	Rx (Packets/Bytes/Dropped/Errors)=(2211/210493/0/0)
	Broadcasts (Tx/Rx)=(0/0) Multicasts=0 Collisions=0
Device=IPsec 0	State=disabled	IP/Mask=0.0.0.0/0.0.0.0	Dependency=Serial 1
Device=IPsec 1	State=running	IP/Mask=192.168.1.35/255.255.255.0	Dependency=Ethernet 1Status: Connected

Tx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Rx (Packets/Bytes/Dropped/Errors)=(0/0/0/0)

Example: Adit MSR> show interface stats

Device=LinkCC 1 State=running

Dependency=None

Status: Operational

Device=LinkCC 2 State=running

Dependency=None

Status: Operational

Device=LinkCC 3 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 4 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 5 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 6 State=down

Dependency=None

Status: Unassigned

Device=LinkCC 7 State=down

Dependency=None

2-16	Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Image 40

Carrier Access none manual Show interface stats, Example Adit MSR show interface stats

Contents

Adit 3000 Series Multi-Service Router MSR Card Customer Support Corporate Contact InformationSupporting Software Versions Preface Preface Table of Contents Global Configuration Mode Configuration LCC Controller Mode Configuration T1 Controller Mode Configuration Dial Peer FXS Mode Configuration Dhcp Pool Ethernet ModeConfiguration Dial Peer Trunk Mode Configuration Dial Peer VoIP Mode Configuration Ethernet Interface Mode Configuration Multilink Interface Mode Configuration Serial Interface Mode Configuration IPSec Mode Configuration L2TPC Mode Configuration Ospf Mode Configuration Pptpc Mode Configuration Radius Mode Configuration Pptps ModeConfiguration Vlan Mode Configuration Vlan Port Mode Configuration Voice Port ModeConfiguration Voice Port FXS Mode Configuration Voice Port Trunk Mode Configuration Voice Service SIP Mode Index Xviii Introduction This Chapter Overview Prompt Identifier Configuration Mode Configuration Mode Link to Command Prompt Displayed Example config# clock source 12 noneds1 1ds1 2ds1 3ds1 Example config# clock 12 source nonet1 port Shortcuts User Mode Commands User ModeDate Enable End Exit Help History Ping Show Traceroute Enable Example adit 3500 enable Password Adit 3500#Date End Exit Help History Ping Syntax ping address -i time -l size -n count -w timeoutstopStop Show Show alarms Show arp Syntax show arp alladdressethernet portAll Display entire ARP table Address Show caclkcd Show caclkcd Example Adit 3500 show caclkcd Show config dynamic-dns Show controller lccSyntax show controller lcc number Example Adit MSR show controller lcc Syntax show controller t1 port Show controller t1Example Adit 3500 show controller t1 Show digit-map Show dhcp-leasesSyntax show digit-map Example Adit 3500 show digit-map Show interface description Show interface multilink Show interface ethernetAdit 3104, Adit 3200, Adit 3500 Value must be Show interface serial Syntax show interface serial portExample Adit 3500 show interface serial Example Adit MSR show interface serial Show interface stats Example Adit MSR show interface stats Supported PlatformsAdit 3104, Adit 3200, Adit 3500, MSR Show ip ospf Syntax show ip ospf Example adit 3500 show ip ospf Show ip ospf database Example adit 3500 show ip ospf database Example adit 3500 show ip ospf database self-originate Show ip ospf interface Ethernet portSerial port Multilink port Show ip ospf neighbor Interface addressDetail Example adit 3500 show Ip ospf neighbor Show licenses FirewallPri Sip Show mac-address-table Example Adit 3500 show log t1 1 minor Show nat-fw Syntax show nat-fw Example Adit 3500 show nat-fw Show route Show port-triggerSyntax show route Example Adit 3500 show route Show service Syntax show service Example Adit 3500 show service Show users Show versionSyntax show users Example Adit 3500 show users Syntax show version Example Adit 3500 show version Example Adit MSR show version Show voice-port fxs Syntax show voice-port fxsExample Adit 3500 show voice-port fxs Example Adit MSR show voice-port fxs Syntax show voice-port trunk port Show voice-port trunkExample Adit 3500 show voice-port trunk Example Adit MSR show voice-port trunk Traceroute Syntax traceroute Syntax traceroute addresshostnamestop User Mode Privileged Mode Privileged Mode Commands Clear Clear arpClear caclkcd Clear ip ospf process Configure terminal Copy defaultsCopy Copy path Copy running-config Syntax # copy running-config path destination-pathDestination-path Example Adit 3500# date Wed Jan 12 103751 Debug Debug portmon all Debug portmon rxtxboth Debug portmon detailBoth Off Ethernet Debug portmon ethernetExample adit 3500# debug portmon ethernet 1 all Debug portmon management Syntax # debug portmon management hushoffHush Off Example adit 3500# debug portmon management hush Debug portmon multilink Syntax # debug portmon raw offon Debug portmon rawExample adit 3500# debug portmon raw off Port Debug portmon serialExample adit 3500# debug portmon 1 rip Syntax # debug trace casprisip enabletxrx Example adit 3500# debug trace cas enableDebug trace Example adit 3500# end Username Adit 3500# help Syntax # history Example adit 3500# history Log clear Syntax # log clear allfirewallprisipsystemt1lccLcc Example adit 3500# log clear firewall No debug No debug portmonNo debug trace Cas Pri Sip Example Adit 3500# ping Example Adit 3500# ping 192.168.1.1 -n 2 -l Example adit 3500# reload Going to reboot Restarting system Reload Show Example adit 3500# show alarms major Syntax # show arp alladdressethernet port Example adit 3500# show arp ethernetExample adit 3500# show arp Example adit 3500# show arp all # show caclkcd Example adit 3500# show caclkcd Show config access-control Syntax # show config controller t1 port Example adit 3500# show config controller t1 Dmz-host 192.168.1.200 enable Syntax # show config interface ethernet port Example adit 3500# show config interface ethernet Syntax # show config interface multilink port Example adit 3500# show config interface multilink Syntax # show config interface serial port Example adit 3500# show config interface serial Syntax # show config ip dhcp ethernet port Example adit 3500# show config ip dhcp ethernet Network-object id 0 description NetworkObject1 ip-address Security-default typical Static-dns hostname test1 ip-address Syntax # show config voice-port fxs port Example adit 3500# show config voice-port fxs Example adit 3500# show config voice-port trunk Syntax # show config voice-port trunk portExample adit MSR# show config voice-port trunk Syntax # show controller lcc number Syntax # show controller t1 port Example adit 3500# show controller t1 Syntax # show digit-map Example adit 3500# show digit-map Example Adit MSR# show interface description Syntax # show interface ethernet port Example adit 3500# show interface ethernetSyntax # show interface multilink port Example adit 3500# show interface multilink Example adit 3500# show interface serial Syntax # show interface serial portExample adit MSR# show interface serial Syntax # show ip ospf Example adit 3500# show ip ospf Show ip ospf database Example adit 3500# show ip ospf database Example adit 3500# show ip ospf database self-originate Example adit 3500# show ip ospf interface ethernet Example adit 3500# show Ip ospf neighbor Example adit 3500# show ip ospf neighbor detail Syntax # show ipsec vpnipsecconnection-id Example adit 3500# show l2tpc Syntax # show l2tpc l2tpc connection-idExample adit 3500# show l2tpc l2tpc # show licenses Example adit 3500# show licenses Example adit 3500# show log t1 1 minor Syntax # show nat-fw Example adit 3500# show nat-fw Show port-trigger Example adit 3500# show pptpc Syntax # show pptpc pptpc connection-idExample adit 3500# show pptpc pptpc Syntax # show pptps Example adit 3500# show pptps Syntax # show route Example adit 3500# show route Show running-config Privileged Mode Example adit MSR# show running-config Privileged Mode Privileged Mode Privileged Mode Supported Platforms Adit 3104, Adit 3200, Adit 3500, MSR # show service Example adit 3500# show service Syntax # show users Example adit 3500# show users Syntax # show version Example adit 3500# show version Example Adit MSR# show version Example adit 3500# show voice-port fxs Syntax # show voice-port fxsExample adit MSR# show voice-port fxs Syntax # show voice-port trunk port Example adit 3500# show voice-port trunk Example adit MSR# show voice-port trunk Upgrade Syntax # upgrade ip-address address file filename checkSyntax # traceroute Syntax # traceroute addresshostnamestop Example Adit 3500# traceroute to Privileged Mode Global Configuration Mode Commands for Entering Configuration Submodes Global Configuration Commands Access Access-controlLan Wan Lan Access-list Authentication login Syntax config# clock 12 source nonet1 portExample config# clock 1 source t1 Clock source Controller lcc Controller t1 Date auto-time-update Date setNtp Tod Example config# date summer-time 03 28 0000 10 28 0100 Date summer-time Delete local-server Date timezone Dial-peer voice Dial-peer voice pots fxsDial-peer voice pots trunk Adit 3500 Range = Dmz-host Dial-peer voice voip User Mode Commands Privileged Mode Commands Dynamic-dns backup-mx Syntax config# dynamic-dns interface eth-2mlink-1ser-nExample config# dynamic-dns interface ser-1 Dynamic-dns Dynamic-dns offline Dynamic-dns mail-exchangerDynamic-dns username Syntax config# exit Example config# exit Syntax config# end Example config# endDynamic-dns wildcard Config# help Or config# ? Config# help History Syntax config# interface ethernet port Example config# interface ethernet Config-int-eth-1#Host-filter Interface ethernet Interface multilink Interface serialAdit 3104, Adit 3200, Adit 3500 Value must be Adit 3200, Adit 3500 Range = Ipsec authentication-retries Example config# ipsec authentication-retries 10 delayIpsec Ipsec key generate key Example config# ipsec log ike msg-outp Ipsec log ike Ipsec net-to-host Ipsec log ipsecAny Ipsec net-to-net Ipsec replayIpsec vpnipsec Remote-ip Ip domain-name Ip dhcp pool ethernetIp host Key L2tpcKey-code Ipsec Local-server New Log lcc buffer LogLog lcc notify Log pri Log security buffer Example config# log security notify warn Example config# log sip buffer-fillLog security notify Log sip Syntax config# log system buffer kilobytes Example config# log system bufferExample config# log system notify error Log system buffer Syntax config# log t1 buffer kilobytes Example config# log t1 bufferExample config# log t1 notify warn Log t1 buffer Mail-server authentication enable Mail-serverMail-server from-address Mail-server host Syntax config# mail-server port port Example config# mail-server portMail-server port Mail-server username Enable Example config# nat-bypass ip-address 10.10.2.1 maskNat-bypass Network-object No access No commandsNo access-control No authentication login No access-listNo date auto-time-update No date summer-time No dial-peer voice pots fxsNo dial-peer voice pots trunk Adit 3500 Range = No dmz-host No dial-peer voice voipNo dynamic-dns No host-filter No ipsec authentication-retriesNo ipsec log ike No ipsec log ipsec Example config# no ipsec log ipsec tcNo ipsec replay No interface multilink No ipsec vpnipsecNo interface serial No key No ip dhcp pool ethernetNo l2tpc No mail-server authentication No local-serverNo log sip No nat-bypass No network-object No port-trigger-serviceNo pptpc No remote-admin icmp No remote-admin snmpSyntax config# no pptps Example config# no pptps No pptps No remote-admin udp-trace No remote-admin telnetExample config# no remote-admin telnet primary-port Example config# no remote-admin web primary-port No remote-admin webNo router ospf Setting Syntax config# no security-log settingNo security-log No service Syntax config# no service service-idExample config# no service-id No snmp-server No time-range No static-dnsNo username No voice-codec No vlanNo voice-port trunk Pptpc Port-trigger servicePptps Remote-admin Remote-admin icmpRemote-admin snmp Radius-client Remote-admin telnet Remote-admin udp-traceExample config# remote-admin telnet primary-port enable Primary-port Example config# remote-admin web primary-port enable Remote-admin webRouter ospf Security-default Typical defaultMaximum Minimum Security-log Service Snmp-server enable Snmp-serverSnmp-server community Server-src-port Snmp-server traps enable Snmp-server hostSnmp-server trusted-ip Version Static-dns Time-range Admin UsernameVlan global Monitor Vlan vlan-id Voice-codec Syntax config# voice-port fxs port Example config# voice-port fxs 1 config-vport-fxs-1#Voice-port global Voice-port fxs Voice-service sip Syntax config# voice-port trunk portExample config# voice-port trunk 1 config-vport-trk-1# Voice-port trunk LCC Controller Commands Configuration LCC Controller ModeDescription End Exit History No command Shutdown Example config-cont-lcc-1# description LCC#1 Syntax config-cont-lcc-n# description textDescription User Mode Commands Syntax config-cont-lcc-n# end Example config-cont-lcc-1# end No command No shutdown Shutdown Configuration T1 Controller Mode T1 Controller Commands Syntax config-cont-t1-n# description text Example config-cont-t1-1# description T1#1 User Mode Commands Syntax config-cont-t1-n# ds0-group timeslots range Example config-cont-t1-1# ds0-group timeslotsSyntax config-cont-t1-n# end Example config-cont-t1-1# end Ds0-group Fdl FramingNone T1.403 Esf Example config-cont-t1-1# idle-pattern 0x7f Syntax config-cont-t1-n# idle-pattern numberIdle-pattern Lbo long LboLbo short Loopback LinecodeAmi B8zs Loopdetect No ds0-groupNo pri-group Csu Niu None No tdm-group Pri-groupIn-out Example config-cont-t1-1# tdm-group timeslots 1-4 dir in-out Tdm-group Threshold Configuration Dhcp Pool Ethernet Mode Dhcp Pool Commands Configuration Dhcp Pool Ethernet Mode Example config-dhcp-eth-1# end-address Syntax config-dhcp-eth-n# end-address addressEnd-address Example config-dhcp-eth-1# lease Syntax config-dhcp-eth-n# lease timeLease No relay No optionNo static-lease Option Relay Syntax config-dhcp-eth-n# start-address address Example config-dhcp-eth-1# start-addressStart-address Static-lease Subnet-mask Wins server Configuration Dial Peer FXS Mode Dial Peer FXS Commands Block-out-caller-id Call-wait-caller-idCall-waiting Calling-party-disc Codec preference Destination-pattern123 G711alaw User Mode Commands Syntax config-dpeer-fxs# end Example config-dpeer-fxs# end Syntax config-dpeer-fxs# fax-protocol nonepass-throught38 Example config-dpeer-fxs# fax-protocol noneFax-protocol Pass-through Example config-dpeer-fxs# modem-protocol pass-though Syntax config-dpeer-fxs# modem-protocol nonepass-throughModem-protocol No block-out-caller-id No call-wait-caller-idNo call-waiting No calling-party-disc No sip-authentication Syntax config-dpeer-fxs# no codec preferenceExample config-dpeer-fxs# no codec preference No codec preference Sip-authentication Sip-authentication enableSip-authentication password Sip-authentication username Configuration Dial Peer Trunk Mode Dial Peer Trunk Commands Syntax config-dpeer-trk# destination-pattern dest-pattern Example config-dpeer-trk# codec preference 1 g711alawExample config-dpeer-trk# destination-pattern 555$ User Mode Commands Syntax config-dpeer-trk# fax-protocol nonepass-throught38 Syntax config-dpeer-trk# end Example config-dpeer-trk# endExample config-dpeer-trk# fax-protocol none Syntax config-dpeer-trk# modem-protocol nonepass-through Example config-dpeer-trk# modem-protocol pass-though Example config-dpeer-trk# no codec preference Syntax config-dpeer-trk# no codec preferenceNo destination-pattern Syntax config-dpeer-trk# prefix prefix Example config-dpeer-trk# prefixPrefix Prefix Example config-dpeer-trk# strip-digits Syntax config-dpeer-trk# strip-digits numberStrip-digits Configuration Dial Peer VoIP Mode Dial Peer VoIP Commands Syntax config-dpeer-voip# destination-pattern number Example config-dpeer-voip# destination-pattern Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 10-3 Syntax config-dpeer-voip end Example config-dpeer-voip# end No prefix No session-target Syntax config-dpeer-voip# prefix prefix Example config-dpeer-voip# prefixExample config-dpeer-voip# session-target ip-address Session-target Syntax config-dpeer-voip# strip-digits number Example config-dpeer-voip# strip-digitsSyntax config-dpeer-voip# user-id user-id Example config-dpeer-voip# user-id testname 10-8 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Ethernet Interface Mode Ethernet Interface Commands Syntax config-int-eth-n# description text Example config-int-eth-1# description Eth#1 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 11-3 Syntax config-int-eth-n# end Example config-int-eth-1# end Firewall Full-duplex Half-duplex Example config-int-eth-1# ip address 192.168.2.100 mask Ip addressAuto Secondary Ip default-gateway Ip default-routeSyntax config-int-eth-n# ip default-gateway address Example config-int-eth-1# ip default-gateway Syntax config-int-eth-n# ip mtu sizeauto Example config-int-eth-1# ip mtu autoIp mtu Auto Message-digest Ip ospf authenticationNull Ip ospf cost Ip ospf authentication-keyIp ospf dead-interval Ip ospf disable Syntax config-int-eth-n# ip ospf hello-interval secondsExample config-int-eth-1# ip ospf hello-interval Ip ospf hello-interval Ip ospf priority Ip ospf transmit-delayIp ospf retransmit-interval Syntax config-int-eth-n# ip primary-dns address Example config-int-eth-1# ip primary-dnsIp primary-dns Ip proxy-arp Ip rip enable Ip ripIp rip receive-version Ip rip send-version Syntax config-int-eth-n# ip route-mode naptroute Example config-int-eth-1# ip route-mode naptIp route Ip route-mode Ip secondary-dns Metric No ip default-route No firewallNo ip address No ip dhcp No ip ospf authentication No ip ospf authentication-keyNo ip ospf cost No ip ospf dead-interval No ip ospf disable Example config-int-eth-1# no ip ospf message-digest-keyNo ip ospf hello-interval No ip ospf message-digest-key No ip ospf transmit-delay No ip ospf priorityNo ip ospf retransmit-interval No ip primary-dns No ip proxy-arp No ip ripNo ip route No ip secondary-dns No schedule-availability No remote-adminNo sip-alg Renew ReleaseNo tos ip Syntax config-int-eth-n# schedule-availability time-range Example config-int-eth-1# schedule-availability time-rangeSchedule-availability Sip-alg Tos Speed100 Auto 11-26 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Multilink Interface Mode Multilink Interface Commands Syntax config-int-mlink-n# description text Example config-int-mlink-1# description MLPPP1 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-3 12-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Example config-int-mlink-1# ip address 192.168.2.100 mask Unnumbered Syntax config-int-mlink-n# ip mtu sizeauto Example config-int-mlink-1# ip mtu auto Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-7 Syntax config-int-mlink-n# ip ospf cost cost Example config-int-mlink-1# ip ospf costSyntax config-int-mlink-n# ip ospf dead-interval seconds Example config-int-mlink-1# ip ospf dead-interval Syntax config-int-mlink-n# ip ospf hello-interval seconds Example config-int-mlink-1# ip ospf hello-interval Syntax config-int-mlink-n# ip ospf priority priority Example config-int-mlink-1# ip ospf priorityExample config-int-mlink-1# ip ospf retransmit-interval Syntax config-int-mlink-n# ip ospf transmit-delay seconds Syntax config-int-mlink-n# ip primary-dns address Example config-int-mlink-1# ip primary-dnsExample config-int-mlink-1# ip rip receive-version none 121or2 Example config-int-mlink-1# ip rip send-version 2-bcast Syntax config-int-mlink-n# ip route-mode naptroute Example config-int-mlink-1# ip route-mode naptSyntax config-int-mlink-n# ip secondary-dns address Example config-int-mlink-1# ip secondary-dns Syntax config-int-mlink-n# no ip address address Example config-int-mlink-1# no ip address Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-15 Example config-int-mlink-1# no ip ospf message-digest-key Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-17 No ppp authentication Syntax config-int-mlink-n# no ip route dest-ip-addr gatewayExample config-int-mlink-1# no ip route 192.168.100.200 No ppp encryption No ppp password No ppp on-demandNo ppp qos interleaving No ppp username 12-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Ppp exec-timeout Ppp authenticationPpp encryption Ppp link-fragmentation Ppp passwordPpp on-demand Ppp qos-interleaving Ppp restart-timerPpp time-btwn-reconnect Syntax config-int-mlink-n# ppp username username Example config-int-mlink-1# ppp username test-user-nameSyntax config-int-mlink-n# schedule-availability time-range Ppp username Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-25 12-26 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Serial Interface Mode Serial Interface Commands Syntax config-int-ser-n# description text Example config-int-ser-1# description Serial1 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-3 Syntax config-int-ser-n# end Example config-int-ser-1# end Encapsulation ppp Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-5 Syntax config-int-ser-n# ip mtu sizeauto Example config-int-ser-1# ip address 192.168.2.100 maskExample config-int-ser-1# ip mtu auto Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-7 Syntax config-int-ser-n# ip ospf cost cost Example config-int-ser-1# ip ospf costSyntax config-int-ser-n# ip ospf dead-interval seconds Example config-int-ser-1# ip ospf dead-interval Syntax config-int-ser-n# ip ospf hello-interval seconds Example config-int-ser-1# ip ospf hello-interval Syntax config-int-ser-n# ip ospf priority priority Example config-int-ser-1# ip ospf priorityExample config-int-ser-1# ip ospf retransmit-interval Syntax config-int-ser-n# ip ospf transmit-delay seconds Syntax config-int-ser-n# ip primary-dns address Example config-int-ser-1# ip primary-dnsSyntax config-int-ser-n# ip rip receive-version 121or2none Example config-int-ser-1# ip rip receive-version none Example config-int-ser-1# ip rip send-version 2-bcast Syntax config-int-ser-n# ip route-mode naptroute Example config-int-ser-1# ip route-mode naptSyntax config-int-ser-n# ip secondary-dns address Example config-int-ser-1# ip secondary-dns Syntax config-int-ser-n# multilink-group group-number Example config-int-ser-1# multilink-groupMultilink-group No encapsulation ppp Syntax config-int-ser-n# no ip address address Example config-int-ser-1# no ip address 13-16 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Example config-int-ser-1# no ip ospf message-digest-key Syntax config-int-ser-n# no ip route dest-ip-addr gateway Example config-int-ser-1# no ip route 192.168.100.200 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-19 13-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Ms-chap Syntax config-int-ser-n# ppp link-fragmentation number Example config-int-ser-1# ppp link-fragmentationSyntax config-int-ser-n# ppp password password Example config-int-ser-1# ppp username test-user-pswrd Syntax config-int-ser-n# ppp restart-timer seconds Example config-int-ser-1# ppp restart-timerSyntax config-int-ser-n# ppp time-btwn-reconnect seconds Example config-int-ser-1# ppp time-btwn-reconnect Syntax config-int-ser-n# schedule-availability time-range Example config-int-ser-1# schedule-availability time-range Configuration IPSec Mode IPSec Commands Authentication Aggressive-modePre-shared Rsa-sig Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 14-3 Dpd-enable Dpd-delayDpd-timeout Encryption Hash GroupMd5 Sha Example config-ipsec-1# ip route metric Syntax config-ipsec n# ip route metric metricIp route metric Ipsec-conn Ipsec-manual Lifetime Local-subnetSingle ip Subnet ip Max-retries ModeTransport Tunnel Net-type Netbios remote-brc-addrDmz lan wan No dpd-delay No dpd-enableNo dpd-timeout No aggressive-mode Example config-ipsec-1# no encryption aes Syntax config-ipsec-n# no groupExample config-ipsec-1# no group No encryption No netbios Syntax config-ipsec-n# no hash md5shaExample config-ipsec-1# no hash md5 No hash No reconnect No set-pfs No transform-set Rekey ReconnectRemote-ip Example config-ipsec-1# schedule-availability rule1 Syntax config-ipsec-n# schedule-availability rule-idRemote-subnet Set-pfs Session-key Example config-ipsec-1# transform-set esp-aes Transform-set Example of IPSec Connection Configuration 14-22 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration L2TPC Mode L2TPC Commands Configuration L2TPC Mode Syntax config-l2tpc-n# end Example config-l2tpc-1# end Example config-l2tpc-1# host-ip Syntax config-l2tpc-n# host-ip addressHost-ip Syntax config-l2tpc-n# ip mtu sizeauto Example config-l2tpc-1# ip address 192.168.2.100 maskExample config-l2tpc-1# ip mtu auto 15-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-l2tpc-n# ip ospf authentication-key password Example config-l2tpc-1# ip ospf authentication-key pass777Syntax config-l2tpc-n# ip ospf cost cost Example config-l2tpc-1# ip ospf cost Syntax config-l2tpc-n# ip ospf hello-interval seconds Example config-l2tpc-1# ip ospf hello-interval Syntax config-l2tpc-n# ip ospf priority priority Example config-l2tpc-1# ip ospf prioritySyntax config-l2tpc-n# ip ospf retransmit-interval seconds Example config-l2tpc-1# ip ospf retransmit-interval Syntax config-l2tpc-n# ip primary-dns address Example config-l2tpc-1# ip primary-dnsSyntax config-l2tpc-n# ip rip receive-version 121or2none Example config-l2tpc-1# ip rip receive-version none Example config-l2tpc-1# ip rip send-version 2-bcast Local-secret Syntax config-l2tpc-n# metric metric Example config-l2tpc-1# metricSyntax config-l2tpc-n# no ip address address Example config-l2tpc-1# no ip address 15-14 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 15-15 Syntax config-l2tpc-n# no ip ospf message-digest-key key-id Example config-l2tpc-1# no ip ospf message-digest-key Syntax config-l2tpc-n# no ip route dest-ip-addr gateway Example config-l2tpc-1# no ip route 192.168.100.200 No ppp exec-timeout No ppp restart-timer No ppp time-btwn-reconnect 15-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Example config-l2tpc-1# ppp authentication chap Syntax config-l2tpc-n# ppp encryption 40-bit128-bitExample config-l2tpc-1# ppp encryption 40-bit Syntax config-l2tpc-n# ppp exec-timeout minutes Syntax config-l2tpc-n# ppp password password Example config-l2tpc-1# ppp password test-user-pswrdSyntax config-l2tpc-n# ppp restart-timer seconds Example config-l2tpc-1# ppp restart-timer Syntax config-l2tpc-n# ppp time-btwn-reconnect seconds Example config-l2tpc-1# ppp time-btwn-reconnectSyntax config-l2tpc-n# ppp username username Example config-l2tpc-1# ppp username test-user-name 15-24 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Ospf Mode Router Ospf Commands Area authentication Area commandsMessage-digest Compatible rfc1583 16-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-ospf# end Example config-ospf# end Syntax config-ospf# exit Example config-ospf# exit Config# Example config-ospf# network 192.168.1.1 0.0.0.255 area Network area No area No area authenticationNo area stub Example config-ospf# no network 192.168.1.1 0.0.0.255 area No compatible rfc1583No network area No router-id Router-id Syntax config-ospf# router-id addressExample router-ospf# router-id Sample Configuration Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 16-11 16-12 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Pptpc Mode Pptp Client Commands Configuration Pptpc Mode Syntax config-pptpc-n# end Example config-pptpc-1# end Syntax config-pptpc-n# host-ip address Example config-pptpc-1# host-ip Syntax config-pptpc-n# ip mtu sizeauto Example config-pptpc-1# ip address 192.168.2.100 maskExample config-pptpc-1# ip mtu auto 17-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-pptpc-n# ip ospf authentication-key password Example config-pptpc-1# ip ospf authentication-key pass777Syntax config-pptpc-n# ip ospf cost cost Example config-pptpc-1# ip ospf cost Syntax config-pptpc-n# ip ospf hello-interval seconds Example config-pptpc-1# ip ospf hello-interval Syntax config-pptpc-n# ip ospf priority priority Example config-pptpc-1# ip ospf prioritySyntax config-pptpc-n# ip ospf retransmit-interval seconds Example config-pptpc-1# ip ospf retransmit-interval Syntax config-pptpc-n# ip primary-dns address Example config-pptpc-1# ip primary-dnsSyntax config-pptpc-n# ip rip receive-version 121or2none Example config-pptpc-1# ip rip receive-version none Example config-pptpc-1# ip rip send-version 2-bcast Syntax config-pptpc-n# ip route-mode naptroute Example config-pptpc-1# ip route-mode naptSyntax config-pptpc-n# ip secondary-dns address Example config-pptpc-1# ip secondary-dns Syntax config-pptpc-n# no ip address address Example config-pptpc-1# no ip address 17-14 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-pptpc-n# no ip ospf message-digest-key key-id Example config-pptpc-1# no ip ospf message-digest-key 17-16 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-pptpc-n# no ip route dest-ip-addr gateway Example config-pptpc-1# no ip route 192.168.100.200 17-18 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 17-19 Syntax config-pptpc-n# ppp encryption 40-bit128-bit Example config-pptpc-1# ppp authentication chapExample config-pptpc-1# ppp encryption 40-bit Syntax config-pptpc-n# ppp exec-timeout minutes Example config-pptpc-1# ppp exec-timeoutSyntax config-pptpc-n# ppp password password Example config-pptpc-1# ppp password test-user-pswrd Syntax config-pptpc-n# ppp restart-timer seconds Example config-pptpc-1# ppp restart-timerSyntax config-pptpc-n# ppp time-btwn-reconnect seconds Example config-pptpc-1# ppp time-btwn-reconnect Example config-pptpc-1# schedule-availability time-range 17-24 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Pptps Mode Pptp Server Commands Configuration Pptps Mode Syntax config-pptps# end Example config-pptps# end Syntax config-pptps# end-address end-ip-addressExample config-pptps# end-address End-ip-address Syntax config-pptps# idle-time seconds Example config-pptps# idle-timeIdle-time Seconds Example config-pptps# no ppp authentication Example config-pptps# no ppp encryptionNo idle-time 40-bit Syntax config-pptps# ppp encryption 40-bit128-bitstateful Example config-pptps# ppp authentication chapExample config-pptps# ppp encryption stateful Syntax config-pptps# start-address start-address Example config-pptps# start-addressStart-ip-address Enter the start IP address of the range 18-8 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Radius Commands Configuration Radius ModeAuthentication End Exit History Host Key Syntax config-radius# authentication chapms-chapms-chapv2pap Example config-radius# authentication chap Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 19-3 Syntax config-radius# end Example config-radius# end Syntax config-radius# host address auth-port port Example config-radius# host 192.168.1.1 auth-portSyntax config-radius# key password Example config-radius# key testpswd 19-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Vlan Mode Vlan Global Commands Configuration Vlan Mode Syntax config-vlan# end Example config-vlan# end Syntax config-vlan# exit Example config-vlan# exit Config# Syntax config-vlan# no port-dot1q ethernet port Example config-vlan# no port-dot1q ethernetSyntax config-vlan# no vlan entry Example config-vlan# no vlan Adit 3104 and Adit 3200 1.1, 1.2, 1.3, 1.4 Adit 3500 and MSR 1.1 Adit 3104 and Adit 3200 1.1, 1.2, 1.3, 1.4 DisableAdit 3500 and MSR 1.1 Syntax config-vlan# tag-all disableenable Example config-vlan# tag-all enableSyntax config-vlan# vlan-feature disableenable Disable Disable Vlan feature Enable Enable Vlan feature 20-8 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Vlan Port Commands Configuration Vlan Port ModeEnd Exit History No commands Port Priority Voip-interface Configuration Vlan Port Mode Syntax config-vlan-n# end Example config-vlan-100# end No port No voip-interface Syntax config-vlan-n# priority priority Example config-vlan-100# priority 21-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Voice Port Commands Configuration Voice Port ModeDigit-map global End Exit History No digit-map global Tos Long-timeout Short-timeoutExample config-vport# digit-map mode long-timeout Digit-map global Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 22-3 Syntax config-vport# end Example config-vport# end Syntax config-vport# exit Example config-vport# exit Config# No digit-map global Pattern numberRtp value hex-value Sip value hex-value 22-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Voice Port FXS Mode Voice Port FXS Commands Example config-vport-fxs-1# description VoiceP-#2 Syntax config-vport-fxs-n# description textComfort-noise Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 23-3 23-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-vport-fxs-n# input-gain value Example config-vport-fxs-1# input-gain No comfort-noise No echo-cancelNo per-line-logging Syntax config-vport-fxs-n# output-gain value Example config-vport-fxs-1# output-gain Syntax config-vport-fxs-n# signal ground-startloop-start Example config-vport-fxs-1# signal ground-start Configuration Voice Port Trunk Mode Voice Port Trunk Commands Connection lcc Connection t1 Digit-map DefaultCustom 24-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Use the end command to exit the current Configuration mode Syntax config-vport-trk-n# input-gain value Example config-vport-trk-1# input-gain Isdn switch-type PRI Example config-vport-trk-1# isdn switch-type pri-ni2 No connection lcc No connection t1 No registration enable No digit-map No registration line No registration line enableNo registration line logging Syntax config-vport-trk-n# output-gain value Example config-vport-trk-1# output-gain Registration line authentication Registration enableRegistration Registration line enable Registration line first-phone-number Example config-vport-trk-1# signal immediate Registration line logging Example config-vport-trk-1# trunk VPtrunk1 Syntax config-vport-trk-n# trunk trunk-idTrunk 24-16 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Voice Service SIP Mode Voice Service SIP Commands Example config-voice-serv-sip# calling-party-disc Syntax config-voice-serv-sip# calling-party-disc durationConference Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 25-3 Dtmf Early-mediaInband Rfc2833 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 25-5 Fax-protocol-t38 ecs Fax-protocol-t38 redundancyHs-redundancy Ls-redundancy Fax-protocol-t38 signaling Feature-mode Example config-voice-serv-sip# gateway-ip Syntax config-voice-serv-sip# gateway-ip addressGateway-ip No conference No outbound-proxyNo prack No proxy-server No redundancy rollback-timer No session-timer modeNo redundancy filter-incoming No registration ignore-negotiated Phone-number Outbound-proxyPrack Proxy-server Privacy-modeRfc3325 Example config-voice-serv-sip# proxy-type generic Example config-voice-serv-sip# redundancy advance-retriesProxy-type Redundancy advance-retries Redundancy advance-timeout Example config-voice-serv-sip# redundancy advance-timeoutExample config-voice-serv-sip# redundancy primary-address Redundancy filter-incoming Redundancy rollback-timer Example config-voice-serv-sip# redundancy rollback-timerExample config-voice-serv-sip# redundancy secondary-address Redundancy secondary-address Redundancy type Redundancy ttlNone Srv User Rtp-base-port Session-timer mode Session-timerSession-timer refresher Session-timer timeout Sip-portTransport Tcp Udp 25-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Index Index Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Index Index Index Index Index FXS Index Index Index Encapsulation ppp Index Index FXS 63,4-64