Lease, Syntax config-dhcp-eth-n# lease time | Carrier Access none

Configuration - DHCP Pool Ethernet Mode

history

Use the history command to display commands that have been entered in this session.

NOTE: This command can be entered in any configuration mode.

Syntax: (config-dhcp-eth-{n})# history

Example: (config-dhcp-eth-1)# history

end-address 192.168.1.250 lease 900

relay 192.168.1.120 start-address 192.168.1.1 subnet-mask 255.255.255.0 history

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

lease

Use the DHCP lease command to define the DHCP lease time, in minutes. This defines the lease duration, or the length of time for which the IP address can be used before a lease renewal is required, or if the address is no longer in use, it is automatically returned to the pool for reallocation.

Syntax: (config-dhcp-eth-{n})# lease time

Field

time

Definition

Enter the DHCP lease time. Range is 1 - 71582788 minutes, with a default of 60.

Example: (config-dhcp-eth-1)# lease 120

Supported Platforms: Adit 3104, Adit 3200, Adit 3500, MSR

7-4	Adit 3000 (Rel. 1.6) and MSR Card (Rel 2.0) CLI

Image 214

Carrier Access none manual Lease, Syntax config-dhcp-eth-n# lease time, Example config-dhcp-eth-1# lease

Contents

Adit 3000 Series Multi-Service Router MSR Card Customer Support Corporate Contact InformationSupporting Software Versions Preface Preface Table of Contents Global Configuration Mode Configuration LCC Controller Mode Configuration T1 Controller Mode Configuration Dial Peer FXS Mode Configuration Dhcp Pool Ethernet ModeConfiguration Dial Peer Trunk Mode Configuration Dial Peer VoIP Mode Configuration Ethernet Interface Mode Configuration Multilink Interface Mode Configuration Serial Interface Mode Configuration IPSec Mode Configuration L2TPC Mode Configuration Ospf Mode Configuration Pptpc Mode Configuration Radius Mode Configuration Pptps ModeConfiguration Vlan Mode Configuration Voice Port FXS Mode Configuration Vlan Port ModeConfiguration Voice Port Mode Configuration Voice Port Trunk Mode Configuration Voice Service SIP Mode Index Xviii Introduction This Chapter Overview Prompt Identifier Configuration Mode Configuration Mode Link to Command Prompt Displayed Example config# clock source 12 noneds1 1ds1 2ds1 3ds1 Example config# clock 12 source nonet1 port Shortcuts User Mode Commands User ModeDate Enable End Exit Help History Ping Show Traceroute Date EnableExample adit 3500 enable Password Adit 3500# End Exit Help History Ping Syntax ping address -i time -l size -n count -w timeoutstopStop Show Show alarms All Display entire ARP table Show arpSyntax show arp alladdressethernet port Address Show caclkcd Show caclkcd Example Adit 3500 show caclkcd Syntax show controller lcc number Show config dynamic-dnsShow controller lcc Example Adit MSR show controller lcc Syntax show controller t1 port Show controller t1Example Adit 3500 show controller t1 Show digit-map Show dhcp-leasesSyntax show digit-map Example Adit 3500 show digit-map Show interface description Show interface multilink Show interface ethernetAdit 3104, Adit 3200, Adit 3500 Value must be Example Adit 3500 show interface serial Show interface serialSyntax show interface serial port Example Adit MSR show interface serial Show interface stats Example Adit MSR show interface stats Supported PlatformsAdit 3104, Adit 3200, Adit 3500, MSR Show ip ospf Syntax show ip ospf Example adit 3500 show ip ospf Show ip ospf database Example adit 3500 show ip ospf database Example adit 3500 show ip ospf database self-originate Serial port Show ip ospf interfaceEthernet port Multilink port Detail Show ip ospf neighborInterface address Example adit 3500 show Ip ospf neighbor Pri Show licensesFirewall Sip Show mac-address-table Example Adit 3500 show log t1 1 minor Show nat-fw Syntax show nat-fw Example Adit 3500 show nat-fw Show route Show port-triggerSyntax show route Example Adit 3500 show route Show service Syntax show service Example Adit 3500 show service Syntax show users Example Adit 3500 show users Show usersShow version Syntax show version Example Adit 3500 show version Example Adit MSR show version Example Adit 3500 show voice-port fxs Show voice-port fxsSyntax show voice-port fxs Example Adit MSR show voice-port fxs Syntax show voice-port trunk port Show voice-port trunkExample Adit 3500 show voice-port trunk Example Adit MSR show voice-port trunk Traceroute Syntax traceroute Syntax traceroute addresshostnamestop User Mode Privileged Mode Privileged Mode Commands Clear caclkcd ClearClear arp Clear ip ospf process Copy Configure terminalCopy defaults Copy path Destination-path Copy running-configSyntax # copy running-config path destination-path Example Adit 3500# date Wed Jan 12 103751 Debug Debug portmon all Both Debug portmon rxtxbothDebug portmon detail Off Ethernet Debug portmon ethernetExample adit 3500# debug portmon ethernet 1 all Hush Off Debug portmon managementSyntax # debug portmon management hushoff Example adit 3500# debug portmon management hush Debug portmon multilink Syntax # debug portmon raw offon Debug portmon rawExample adit 3500# debug portmon raw off Port Debug portmon serialExample adit 3500# debug portmon 1 rip Debug trace Syntax # debug trace casprisip enabletxrxExample adit 3500# debug trace cas enable Example adit 3500# end Username Adit 3500# help Syntax # history Example adit 3500# history Lcc Log clearSyntax # log clear allfirewallprisipsystemt1lcc Example adit 3500# log clear firewall No debug trace No debugNo debug portmon Cas Pri Sip Example Adit 3500# ping Example Adit 3500# ping 192.168.1.1 -n 2 -l Example adit 3500# reload Going to reboot Restarting system Reload Show Example adit 3500# show alarms major Example adit 3500# show arp Syntax # show arp alladdressethernet portExample adit 3500# show arp ethernet Example adit 3500# show arp all # show caclkcd Example adit 3500# show caclkcd Show config access-control Syntax # show config controller t1 port Example adit 3500# show config controller t1 Dmz-host 192.168.1.200 enable Syntax # show config interface ethernet port Example adit 3500# show config interface ethernet Syntax # show config interface multilink port Example adit 3500# show config interface multilink Syntax # show config interface serial port Example adit 3500# show config interface serial Syntax # show config ip dhcp ethernet port Example adit 3500# show config ip dhcp ethernet Network-object id 0 description NetworkObject1 ip-address Security-default typical Static-dns hostname test1 ip-address Syntax # show config voice-port fxs port Example adit 3500# show config voice-port fxs Example adit 3500# show config voice-port trunk Syntax # show config voice-port trunk portExample adit MSR# show config voice-port trunk Syntax # show controller lcc number Syntax # show controller t1 port Example adit 3500# show controller t1 Syntax # show digit-map Example adit 3500# show digit-map Example Adit MSR# show interface description Syntax # show interface multilink port Syntax # show interface ethernet portExample adit 3500# show interface ethernet Example adit 3500# show interface multilink Example adit 3500# show interface serial Syntax # show interface serial portExample adit MSR# show interface serial Syntax # show ip ospf Example adit 3500# show ip ospf Show ip ospf database Example adit 3500# show ip ospf database Example adit 3500# show ip ospf database self-originate Example adit 3500# show ip ospf interface ethernet Example adit 3500# show Ip ospf neighbor Example adit 3500# show ip ospf neighbor detail Syntax # show ipsec vpnipsecconnection-id Example adit 3500# show l2tpc Syntax # show l2tpc l2tpc connection-idExample adit 3500# show l2tpc l2tpc # show licenses Example adit 3500# show licenses Example adit 3500# show log t1 1 minor Syntax # show nat-fw Example adit 3500# show nat-fw Show port-trigger Example adit 3500# show pptpc Syntax # show pptpc pptpc connection-idExample adit 3500# show pptpc pptpc Syntax # show pptps Example adit 3500# show pptps Syntax # show route Example adit 3500# show route Show running-config Privileged Mode Example adit MSR# show running-config Privileged Mode Privileged Mode Privileged Mode Supported Platforms Adit 3104, Adit 3200, Adit 3500, MSR # show service Example adit 3500# show service Syntax # show users Example adit 3500# show users Syntax # show version Example adit 3500# show version Example Adit MSR# show version Example adit 3500# show voice-port fxs Syntax # show voice-port fxsExample adit MSR# show voice-port fxs Syntax # show voice-port trunk port Example adit 3500# show voice-port trunk Example adit MSR# show voice-port trunk Syntax # traceroute Syntax # traceroute addresshostnamestop UpgradeSyntax # upgrade ip-address address file filename check Example Adit 3500# traceroute to Privileged Mode Global Configuration Mode Commands for Entering Configuration Submodes Global Configuration Commands Lan Wan AccessAccess-control Lan Access-list Example config# clock 1 source t1 Authentication loginSyntax config# clock 12 source nonet1 port Clock source Controller lcc Controller t1 Ntp Date auto-time-updateDate set Tod Example config# date summer-time 03 28 0000 10 28 0100 Date summer-time Delete local-server Date timezone Dial-peer voice pots trunk Dial-peer voiceDial-peer voice pots fxs Adit 3500 Range = Dmz-host Dial-peer voice voip User Mode Commands Privileged Mode Commands Example config# dynamic-dns interface ser-1 Dynamic-dns backup-mxSyntax config# dynamic-dns interface eth-2mlink-1ser-n Dynamic-dns Dynamic-dns offline Dynamic-dns mail-exchangerDynamic-dns username Syntax config# exit Example config# exit Syntax config# end Example config# endDynamic-dns wildcard Config# help Or config# ? Config# help History Host-filter Syntax config# interface ethernet portExample config# interface ethernet Config-int-eth-1# Interface ethernet Adit 3104, Adit 3200, Adit 3500 Value must be Interface multilinkInterface serial Adit 3200, Adit 3500 Range = Ipsec Ipsec authentication-retriesExample config# ipsec authentication-retries 10 delay Ipsec key generate key Example config# ipsec log ike msg-outp Ipsec log ike Ipsec net-to-host Ipsec log ipsecAny Ipsec vpnipsec Ipsec net-to-netIpsec replay Remote-ip Ip domain-name Ip dhcp pool ethernetIp host Key-code KeyL2tpc Ipsec Local-server New Log lcc buffer LogLog lcc notify Log pri Log security buffer Log security notify Example config# log security notify warnExample config# log sip buffer-fill Log sip Example config# log system notify error Syntax config# log system buffer kilobytesExample config# log system buffer Log system buffer Example config# log t1 notify warn Syntax config# log t1 buffer kilobytesExample config# log t1 buffer Log t1 buffer Mail-server from-address Mail-server authentication enableMail-server Mail-server host Mail-server port Syntax config# mail-server port portExample config# mail-server port Mail-server username Nat-bypass EnableExample config# nat-bypass ip-address 10.10.2.1 mask Network-object No access No commandsNo access-control No authentication login No access-listNo date auto-time-update No dial-peer voice pots trunk No date summer-timeNo dial-peer voice pots fxs Adit 3500 Range = No dmz-host No dial-peer voice voipNo dynamic-dns No host-filter No ipsec authentication-retriesNo ipsec log ike No ipsec log ipsec Example config# no ipsec log ipsec tcNo ipsec replay No interface multilink No ipsec vpnipsecNo interface serial No key No ip dhcp pool ethernetNo l2tpc No log sip No mail-server authenticationNo local-server No nat-bypass No network-object No port-trigger-serviceNo pptpc Syntax config# no pptps Example config# no pptps No remote-admin icmpNo remote-admin snmp No pptps No remote-admin udp-trace No remote-admin telnetExample config# no remote-admin telnet primary-port Example config# no remote-admin web primary-port No remote-admin webNo router ospf Setting Syntax config# no security-log settingNo security-log Example config# no service-id No serviceSyntax config# no service service-id No snmp-server No time-range No static-dnsNo username No voice-codec No vlanNo voice-port trunk Pptpc Port-trigger servicePptps Remote-admin snmp Remote-adminRemote-admin icmp Radius-client Example config# remote-admin telnet primary-port enable Remote-admin telnetRemote-admin udp-trace Primary-port Example config# remote-admin web primary-port enable Remote-admin webRouter ospf Maximum Security-defaultTypical default Minimum Security-log Service Snmp-server community Snmp-server enableSnmp-server Server-src-port Snmp-server trusted-ip Snmp-server traps enableSnmp-server host Version Static-dns Time-range Vlan global AdminUsername Monitor Vlan vlan-id Voice-codec Voice-port global Syntax config# voice-port fxs portExample config# voice-port fxs 1 config-vport-fxs-1# Voice-port fxs Example config# voice-port trunk 1 config-vport-trk-1# Voice-service sipSyntax config# voice-port trunk port Voice-port trunk LCC Controller Commands Configuration LCC Controller ModeDescription End Exit History No command Shutdown Example config-cont-lcc-1# description LCC#1 Syntax config-cont-lcc-n# description textDescription User Mode Commands Syntax config-cont-lcc-n# end Example config-cont-lcc-1# end No command No shutdown Shutdown Configuration T1 Controller Mode T1 Controller Commands Syntax config-cont-t1-n# description text Example config-cont-t1-1# description T1#1 User Mode Commands Syntax config-cont-t1-n# end Example config-cont-t1-1# end Syntax config-cont-t1-n# ds0-group timeslots rangeExample config-cont-t1-1# ds0-group timeslots Ds0-group None T1.403 FdlFraming Esf Example config-cont-t1-1# idle-pattern 0x7f Syntax config-cont-t1-n# idle-pattern numberIdle-pattern Lbo long LboLbo short Loopback LinecodeAmi B8zs No pri-group LoopdetectNo ds0-group Csu Niu None No tdm-group Pri-groupIn-out Example config-cont-t1-1# tdm-group timeslots 1-4 dir in-out Tdm-group Threshold Configuration Dhcp Pool Ethernet Mode Dhcp Pool Commands Configuration Dhcp Pool Ethernet Mode Example config-dhcp-eth-1# end-address Syntax config-dhcp-eth-n# end-address addressEnd-address Example config-dhcp-eth-1# lease Syntax config-dhcp-eth-n# lease timeLease No relay No optionNo static-lease Option Relay Start-address Syntax config-dhcp-eth-n# start-address addressExample config-dhcp-eth-1# start-address Static-lease Subnet-mask Wins server Configuration Dial Peer FXS Mode Dial Peer FXS Commands Call-waiting Block-out-caller-idCall-wait-caller-id Calling-party-disc 123 Codec preferenceDestination-pattern G711alaw User Mode Commands Syntax config-dpeer-fxs# end Example config-dpeer-fxs# end Fax-protocol Syntax config-dpeer-fxs# fax-protocol nonepass-throught38Example config-dpeer-fxs# fax-protocol none Pass-through Example config-dpeer-fxs# modem-protocol pass-though Syntax config-dpeer-fxs# modem-protocol nonepass-throughModem-protocol No call-waiting No block-out-caller-idNo call-wait-caller-id No calling-party-disc Example config-dpeer-fxs# no codec preference No sip-authenticationSyntax config-dpeer-fxs# no codec preference No codec preference Sip-authentication password Sip-authenticationSip-authentication enable Sip-authentication username Configuration Dial Peer Trunk Mode Dial Peer Trunk Commands Syntax config-dpeer-trk# destination-pattern dest-pattern Example config-dpeer-trk# codec preference 1 g711alawExample config-dpeer-trk# destination-pattern 555$ User Mode Commands Syntax config-dpeer-trk# fax-protocol nonepass-throught38 Syntax config-dpeer-trk# end Example config-dpeer-trk# endExample config-dpeer-trk# fax-protocol none Syntax config-dpeer-trk# modem-protocol nonepass-through Example config-dpeer-trk# modem-protocol pass-though Example config-dpeer-trk# no codec preference Syntax config-dpeer-trk# no codec preferenceNo destination-pattern Prefix Syntax config-dpeer-trk# prefix prefixExample config-dpeer-trk# prefix Prefix Example config-dpeer-trk# strip-digits Syntax config-dpeer-trk# strip-digits numberStrip-digits Configuration Dial Peer VoIP Mode Dial Peer VoIP Commands Syntax config-dpeer-voip# destination-pattern number Example config-dpeer-voip# destination-pattern Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 10-3 Syntax config-dpeer-voip end Example config-dpeer-voip# end No prefix No session-target Example config-dpeer-voip# session-target ip-address Syntax config-dpeer-voip# prefix prefixExample config-dpeer-voip# prefix Session-target Syntax config-dpeer-voip# user-id user-id Syntax config-dpeer-voip# strip-digits numberExample config-dpeer-voip# strip-digits Example config-dpeer-voip# user-id testname 10-8 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Ethernet Interface Mode Ethernet Interface Commands Syntax config-int-eth-n# description text Example config-int-eth-1# description Eth#1 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 11-3 Syntax config-int-eth-n# end Example config-int-eth-1# end Firewall Full-duplex Half-duplex Auto Example config-int-eth-1# ip address 192.168.2.100 maskIp address Secondary Syntax config-int-eth-n# ip default-gateway address Ip default-gatewayIp default-route Example config-int-eth-1# ip default-gateway Ip mtu Syntax config-int-eth-n# ip mtu sizeautoExample config-int-eth-1# ip mtu auto Auto Message-digest Ip ospf authenticationNull Ip ospf cost Ip ospf authentication-keyIp ospf dead-interval Example config-int-eth-1# ip ospf hello-interval Ip ospf disableSyntax config-int-eth-n# ip ospf hello-interval seconds Ip ospf hello-interval Ip ospf priority Ip ospf transmit-delayIp ospf retransmit-interval Ip primary-dns Syntax config-int-eth-n# ip primary-dns addressExample config-int-eth-1# ip primary-dns Ip proxy-arp Ip rip receive-version Ip rip enableIp rip Ip rip send-version Ip route Syntax config-int-eth-n# ip route-mode naptrouteExample config-int-eth-1# ip route-mode napt Ip route-mode Ip secondary-dns Metric No ip address No ip default-routeNo firewall No ip dhcp No ip ospf cost No ip ospf authenticationNo ip ospf authentication-key No ip ospf dead-interval No ip ospf hello-interval No ip ospf disableExample config-int-eth-1# no ip ospf message-digest-key No ip ospf message-digest-key No ip ospf retransmit-interval No ip ospf transmit-delayNo ip ospf priority No ip primary-dns No ip route No ip proxy-arpNo ip rip No ip secondary-dns No schedule-availability No remote-adminNo sip-alg Renew ReleaseNo tos ip Schedule-availability Syntax config-int-eth-n# schedule-availability time-rangeExample config-int-eth-1# schedule-availability time-range Sip-alg Tos Speed100 Auto 11-26 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Multilink Interface Mode Multilink Interface Commands Syntax config-int-mlink-n# description text Example config-int-mlink-1# description MLPPP1 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-3 12-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Example config-int-mlink-1# ip address 192.168.2.100 mask Unnumbered Syntax config-int-mlink-n# ip mtu sizeauto Example config-int-mlink-1# ip mtu auto Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-7 Syntax config-int-mlink-n# ip ospf dead-interval seconds Syntax config-int-mlink-n# ip ospf cost costExample config-int-mlink-1# ip ospf cost Example config-int-mlink-1# ip ospf dead-interval Syntax config-int-mlink-n# ip ospf hello-interval seconds Example config-int-mlink-1# ip ospf hello-interval Example config-int-mlink-1# ip ospf retransmit-interval Syntax config-int-mlink-n# ip ospf priority priorityExample config-int-mlink-1# ip ospf priority Syntax config-int-mlink-n# ip ospf transmit-delay seconds Example config-int-mlink-1# ip rip receive-version none Syntax config-int-mlink-n# ip primary-dns addressExample config-int-mlink-1# ip primary-dns 121or2 Example config-int-mlink-1# ip rip send-version 2-bcast Syntax config-int-mlink-n# ip secondary-dns address Syntax config-int-mlink-n# ip route-mode naptrouteExample config-int-mlink-1# ip route-mode napt Example config-int-mlink-1# ip secondary-dns Syntax config-int-mlink-n# no ip address address Example config-int-mlink-1# no ip address Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-15 Example config-int-mlink-1# no ip ospf message-digest-key Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-17 Example config-int-mlink-1# no ip route 192.168.100.200 No ppp authenticationSyntax config-int-mlink-n# no ip route dest-ip-addr gateway No ppp encryption No ppp qos interleaving No ppp passwordNo ppp on-demand No ppp username 12-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Ppp exec-timeout Ppp authenticationPpp encryption Ppp link-fragmentation Ppp passwordPpp on-demand Ppp qos-interleaving Ppp restart-timerPpp time-btwn-reconnect Syntax config-int-mlink-n# schedule-availability time-range Syntax config-int-mlink-n# ppp username usernameExample config-int-mlink-1# ppp username test-user-name Ppp username Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 12-25 12-26 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Serial Interface Mode Serial Interface Commands Syntax config-int-ser-n# description text Example config-int-ser-1# description Serial1 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-3 Syntax config-int-ser-n# end Example config-int-ser-1# end Encapsulation ppp Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-5 Syntax config-int-ser-n# ip mtu sizeauto Example config-int-ser-1# ip address 192.168.2.100 maskExample config-int-ser-1# ip mtu auto Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-7 Syntax config-int-ser-n# ip ospf dead-interval seconds Syntax config-int-ser-n# ip ospf cost costExample config-int-ser-1# ip ospf cost Example config-int-ser-1# ip ospf dead-interval Syntax config-int-ser-n# ip ospf hello-interval seconds Example config-int-ser-1# ip ospf hello-interval Example config-int-ser-1# ip ospf retransmit-interval Syntax config-int-ser-n# ip ospf priority priorityExample config-int-ser-1# ip ospf priority Syntax config-int-ser-n# ip ospf transmit-delay seconds Syntax config-int-ser-n# ip rip receive-version 121or2none Syntax config-int-ser-n# ip primary-dns addressExample config-int-ser-1# ip primary-dns Example config-int-ser-1# ip rip receive-version none Example config-int-ser-1# ip rip send-version 2-bcast Syntax config-int-ser-n# ip secondary-dns address Syntax config-int-ser-n# ip route-mode naptrouteExample config-int-ser-1# ip route-mode napt Example config-int-ser-1# ip secondary-dns Multilink-group Syntax config-int-ser-n# multilink-group group-numberExample config-int-ser-1# multilink-group No encapsulation ppp Syntax config-int-ser-n# no ip address address Example config-int-ser-1# no ip address 13-16 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Example config-int-ser-1# no ip ospf message-digest-key Syntax config-int-ser-n# no ip route dest-ip-addr gateway Example config-int-ser-1# no ip route 192.168.100.200 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 13-19 13-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Ms-chap Syntax config-int-ser-n# ppp password password Syntax config-int-ser-n# ppp link-fragmentation numberExample config-int-ser-1# ppp link-fragmentation Example config-int-ser-1# ppp username test-user-pswrd Syntax config-int-ser-n# ppp time-btwn-reconnect seconds Syntax config-int-ser-n# ppp restart-timer secondsExample config-int-ser-1# ppp restart-timer Example config-int-ser-1# ppp time-btwn-reconnect Syntax config-int-ser-n# schedule-availability time-range Example config-int-ser-1# schedule-availability time-range Configuration IPSec Mode IPSec Commands Pre-shared AuthenticationAggressive-mode Rsa-sig Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 14-3 Dpd-enable Dpd-delayDpd-timeout Encryption Hash GroupMd5 Sha Example config-ipsec-1# ip route metric Syntax config-ipsec n# ip route metric metricIp route metric Ipsec-conn Ipsec-manual Single ip LifetimeLocal-subnet Subnet ip Transport Max-retriesMode Tunnel Net-type Netbios remote-brc-addrDmz lan wan No dpd-timeout No dpd-delayNo dpd-enable No aggressive-mode Example config-ipsec-1# no group Example config-ipsec-1# no encryption aesSyntax config-ipsec-n# no group No encryption Example config-ipsec-1# no hash md5 No netbiosSyntax config-ipsec-n# no hash md5sha No hash No reconnect No set-pfs No transform-set Rekey ReconnectRemote-ip Example config-ipsec-1# schedule-availability rule1 Syntax config-ipsec-n# schedule-availability rule-idRemote-subnet Set-pfs Session-key Example config-ipsec-1# transform-set esp-aes Transform-set Example of IPSec Connection Configuration 14-22 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration L2TPC Mode L2TPC Commands Configuration L2TPC Mode Syntax config-l2tpc-n# end Example config-l2tpc-1# end Example config-l2tpc-1# host-ip Syntax config-l2tpc-n# host-ip addressHost-ip Syntax config-l2tpc-n# ip mtu sizeauto Example config-l2tpc-1# ip address 192.168.2.100 maskExample config-l2tpc-1# ip mtu auto 15-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-l2tpc-n# ip ospf cost cost Syntax config-l2tpc-n# ip ospf authentication-key passwordExample config-l2tpc-1# ip ospf authentication-key pass777 Example config-l2tpc-1# ip ospf cost Syntax config-l2tpc-n# ip ospf hello-interval seconds Example config-l2tpc-1# ip ospf hello-interval Syntax config-l2tpc-n# ip ospf retransmit-interval seconds Syntax config-l2tpc-n# ip ospf priority priorityExample config-l2tpc-1# ip ospf priority Example config-l2tpc-1# ip ospf retransmit-interval Syntax config-l2tpc-n# ip rip receive-version 121or2none Syntax config-l2tpc-n# ip primary-dns addressExample config-l2tpc-1# ip primary-dns Example config-l2tpc-1# ip rip receive-version none Example config-l2tpc-1# ip rip send-version 2-bcast Local-secret Syntax config-l2tpc-n# no ip address address Syntax config-l2tpc-n# metric metricExample config-l2tpc-1# metric Example config-l2tpc-1# no ip address 15-14 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 15-15 Syntax config-l2tpc-n# no ip ospf message-digest-key key-id Example config-l2tpc-1# no ip ospf message-digest-key Syntax config-l2tpc-n# no ip route dest-ip-addr gateway Example config-l2tpc-1# no ip route 192.168.100.200 No ppp exec-timeout No ppp restart-timer No ppp time-btwn-reconnect 15-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Example config-l2tpc-1# ppp encryption 40-bit Example config-l2tpc-1# ppp authentication chapSyntax config-l2tpc-n# ppp encryption 40-bit128-bit Syntax config-l2tpc-n# ppp exec-timeout minutes Syntax config-l2tpc-n# ppp restart-timer seconds Syntax config-l2tpc-n# ppp password passwordExample config-l2tpc-1# ppp password test-user-pswrd Example config-l2tpc-1# ppp restart-timer Syntax config-l2tpc-n# ppp username username Syntax config-l2tpc-n# ppp time-btwn-reconnect secondsExample config-l2tpc-1# ppp time-btwn-reconnect Example config-l2tpc-1# ppp username test-user-name 15-24 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Ospf Mode Router Ospf Commands Area authentication Area commandsMessage-digest Compatible rfc1583 16-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-ospf# end Example config-ospf# end Syntax config-ospf# exit Example config-ospf# exit Config# Example config-ospf# network 192.168.1.1 0.0.0.255 area Network area No area No area authenticationNo area stub No network area Example config-ospf# no network 192.168.1.1 0.0.0.255 areaNo compatible rfc1583 No router-id Router-id Syntax config-ospf# router-id addressExample router-ospf# router-id Sample Configuration Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 16-11 16-12 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Pptpc Mode Pptp Client Commands Configuration Pptpc Mode Syntax config-pptpc-n# end Example config-pptpc-1# end Syntax config-pptpc-n# host-ip address Example config-pptpc-1# host-ip Syntax config-pptpc-n# ip mtu sizeauto Example config-pptpc-1# ip address 192.168.2.100 maskExample config-pptpc-1# ip mtu auto 17-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-pptpc-n# ip ospf cost cost Syntax config-pptpc-n# ip ospf authentication-key passwordExample config-pptpc-1# ip ospf authentication-key pass777 Example config-pptpc-1# ip ospf cost Syntax config-pptpc-n# ip ospf hello-interval seconds Example config-pptpc-1# ip ospf hello-interval Syntax config-pptpc-n# ip ospf retransmit-interval seconds Syntax config-pptpc-n# ip ospf priority priorityExample config-pptpc-1# ip ospf priority Example config-pptpc-1# ip ospf retransmit-interval Syntax config-pptpc-n# ip rip receive-version 121or2none Syntax config-pptpc-n# ip primary-dns addressExample config-pptpc-1# ip primary-dns Example config-pptpc-1# ip rip receive-version none Example config-pptpc-1# ip rip send-version 2-bcast Syntax config-pptpc-n# ip secondary-dns address Syntax config-pptpc-n# ip route-mode naptrouteExample config-pptpc-1# ip route-mode napt Example config-pptpc-1# ip secondary-dns Syntax config-pptpc-n# no ip address address Example config-pptpc-1# no ip address 17-14 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-pptpc-n# no ip ospf message-digest-key key-id Example config-pptpc-1# no ip ospf message-digest-key 17-16 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-pptpc-n# no ip route dest-ip-addr gateway Example config-pptpc-1# no ip route 192.168.100.200 17-18 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 17-19 Syntax config-pptpc-n# ppp encryption 40-bit128-bit Example config-pptpc-1# ppp authentication chapExample config-pptpc-1# ppp encryption 40-bit Syntax config-pptpc-n# ppp password password Syntax config-pptpc-n# ppp exec-timeout minutesExample config-pptpc-1# ppp exec-timeout Example config-pptpc-1# ppp password test-user-pswrd Syntax config-pptpc-n# ppp time-btwn-reconnect seconds Syntax config-pptpc-n# ppp restart-timer secondsExample config-pptpc-1# ppp restart-timer Example config-pptpc-1# ppp time-btwn-reconnect Example config-pptpc-1# schedule-availability time-range 17-24 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Pptps Mode Pptp Server Commands Configuration Pptps Mode Example config-pptps# end-address Syntax config-pptps# end Example config-pptps# endSyntax config-pptps# end-address end-ip-address End-ip-address Idle-time Syntax config-pptps# idle-time secondsExample config-pptps# idle-time Seconds No idle-time Example config-pptps# no ppp authenticationExample config-pptps# no ppp encryption 40-bit Syntax config-pptps# ppp encryption 40-bit128-bitstateful Example config-pptps# ppp authentication chapExample config-pptps# ppp encryption stateful Start-ip-address Syntax config-pptps# start-address start-addressExample config-pptps# start-address Enter the start IP address of the range 18-8 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Radius Commands Configuration Radius ModeAuthentication End Exit History Host Key Syntax config-radius# authentication chapms-chapms-chapv2pap Example config-radius# authentication chap Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 19-3 Syntax config-radius# end Example config-radius# end Syntax config-radius# key password Syntax config-radius# host address auth-port portExample config-radius# host 192.168.1.1 auth-port Example config-radius# key testpswd 19-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Vlan Mode Vlan Global Commands Configuration Vlan Mode Syntax config-vlan# end Example config-vlan# end Syntax config-vlan# exit Example config-vlan# exit Config# Syntax config-vlan# no vlan entry Syntax config-vlan# no port-dot1q ethernet portExample config-vlan# no port-dot1q ethernet Example config-vlan# no vlan Adit 3104 and Adit 3200 1.1, 1.2, 1.3, 1.4 Adit 3500 and MSR 1.1 Adit 3104 and Adit 3200 1.1, 1.2, 1.3, 1.4 DisableAdit 3500 and MSR 1.1 Syntax config-vlan# vlan-feature disableenable Syntax config-vlan# tag-all disableenableExample config-vlan# tag-all enable Disable Disable Vlan feature Enable Enable Vlan feature 20-8 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Vlan Port Commands Configuration Vlan Port ModeEnd Exit History No commands Port Priority Voip-interface Configuration Vlan Port Mode Syntax config-vlan-n# end Example config-vlan-100# end No port No voip-interface Syntax config-vlan-n# priority priority Example config-vlan-100# priority 21-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Voice Port Commands Configuration Voice Port ModeDigit-map global End Exit History No digit-map global Tos Example config-vport# digit-map mode long-timeout Long-timeoutShort-timeout Digit-map global Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 22-3 Syntax config-vport# end Example config-vport# end Syntax config-vport# exit Example config-vport# exit Config# Rtp value hex-value No digit-map globalPattern number Sip value hex-value 22-6 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Voice Port FXS Mode Voice Port FXS Commands Example config-vport-fxs-1# description VoiceP-#2 Syntax config-vport-fxs-n# description textComfort-noise Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 23-3 23-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Syntax config-vport-fxs-n# input-gain value Example config-vport-fxs-1# input-gain No comfort-noise No echo-cancelNo per-line-logging Syntax config-vport-fxs-n# output-gain value Example config-vport-fxs-1# output-gain Syntax config-vport-fxs-n# signal ground-startloop-start Example config-vport-fxs-1# signal ground-start Configuration Voice Port Trunk Mode Voice Port Trunk Commands Connection lcc Connection t1 Digit-map DefaultCustom 24-4 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Use the end command to exit the current Configuration mode Syntax config-vport-trk-n# input-gain value Example config-vport-trk-1# input-gain Isdn switch-type PRI Example config-vport-trk-1# isdn switch-type pri-ni2 No connection lcc No connection t1 No registration enable No digit-map No registration line No registration line enableNo registration line logging Syntax config-vport-trk-n# output-gain value Example config-vport-trk-1# output-gain Registration line authentication Registration enableRegistration Registration line enable Registration line first-phone-number Example config-vport-trk-1# signal immediate Registration line logging Example config-vport-trk-1# trunk VPtrunk1 Syntax config-vport-trk-n# trunk trunk-idTrunk 24-16 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Configuration Voice Service SIP Mode Voice Service SIP Commands Example config-voice-serv-sip# calling-party-disc Syntax config-voice-serv-sip# calling-party-disc durationConference Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 25-3 Inband DtmfEarly-media Rfc2833 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI 25-5 Hs-redundancy Fax-protocol-t38 ecsFax-protocol-t38 redundancy Ls-redundancy Fax-protocol-t38 signaling Feature-mode Example config-voice-serv-sip# gateway-ip Syntax config-voice-serv-sip# gateway-ip addressGateway-ip No prack No conferenceNo outbound-proxy No proxy-server No redundancy filter-incoming No redundancy rollback-timerNo session-timer mode No registration ignore-negotiated Phone-number Outbound-proxyPrack Proxy-server Privacy-modeRfc3325 Proxy-type Example config-voice-serv-sip# proxy-type genericExample config-voice-serv-sip# redundancy advance-retries Redundancy advance-retries Example config-voice-serv-sip# redundancy primary-address Redundancy advance-timeoutExample config-voice-serv-sip# redundancy advance-timeout Redundancy filter-incoming Example config-voice-serv-sip# redundancy secondary-address Redundancy rollback-timerExample config-voice-serv-sip# redundancy rollback-timer Redundancy secondary-address Redundancy type Redundancy ttlNone Srv User Rtp-base-port Session-timer mode Session-timerSession-timer refresher Transport Session-timer timeoutSip-port Tcp Udp 25-20 Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Index Index Adit 3000 Rel .6 and MSR Card Rel 2.0 CLI Index Index Index Index Index FXS Index Index Index Encapsulation ppp Index Index FXS 63,4-64