F523

F523

Pattern Group 1 Selection 1

Program Pattern Run Speeds

Groups of configured Preset Speeds may be selected and run from this screen. The execution of grouped Preset Speeds in this manner is called a Pattern Run.

One to eight user-selected Preset Speeds may be run sequentially for a user-set number of repetitions. The group of user-selected Preset Speeds is called a Pattern Group. The Pattern Run function executes the user-set Pattern Group.

Pattern Group 1 is comprised of up to 8 Selections with each Selection being 1 of 15 possible Preset Speed settings. Skip may be selected to ignore a Selection.

This parameter allows the user to choose one configured Preset Speed that is to be used as Selection 1 (of 8) for Pattern Group 1. See F018 for information on configuring the individual Preset Speeds. Parameters F524 F530 may be setup for subsequent Selections 2 8.

One Preset Speed number (1 – 15) or Skip is selected for Selection 1 (F523). The number of times to repeat Pattern Group 1 is selected at F522. Set this value to 255 to run forever.

Setup Pattern Group 2 at F531 F539 if more Preset Speed entries are required.

Pattern Run Setup (for Pattern Group 1)

1.From Program Pattern Run Speeds, select the Preset Speeds that are to be used as the Pattern Group 1 set of Selections. Select a speed from the 1 – 15 configured presets; 1 speed number per Selection. Set any unused Selections to Skip.

2.From Program Pattern Run Pattern Run Pattern Operation Selection, enable the Pattern Run mode of operation by selecting Seconds or Minutes as the unit of measure for the Operation Time setting.

3.From Program Pattern Run Operation Time, set the run-time for each Preset Speed selected in step 1.

4.Configure two unused discrete input terminals for Pattern Operation Group 1 and Pattern Operation Trigger Signal.

Note: Activation of the Pattern Operation Group 1 discrete input terminal is required to enable Pattern Group 1 for use. Activation of the Pattern Operation Trigger Signal discrete input terminal starts the Pattern Group 1 pattern run.

5.From Program Pattern Run Pattern Run Pattern 1 Repeat, set to the number of times that Pattern Group 1 is to be run. Set to 255 to run forever.

6.From Program Pattern Run Pattern Run Pattern Operation Mode, set the end-of-pattern command to Reset or Continue.

7.From the Remote mode (LocalRemote light is off), initiate a Run command (i.e., F and/or R terminal On).

8.Connect the Pattern Operation Group 1 input terminal to CC.

9.Connect the Pattern Operation Trigger Signal input terminal to CC and the Pattern Run will start and continue as programmed.

10.Open the Pattern Operation Trigger Signal connection to CC to stop the Pattern Run before its conclusion if required.

Direct Access Number — F523

Parameter Type — Selection List

Factory Default — Skip

Changeable During Run — No

Minimum — Skip

Maximum — 15

Units — Preset Speed Number

Pattern Group 1

 

 

 

Selection

 

 

 

 

 

 

 

 

 

 

 

F523

F524

F525

F526

F527

F528

F529

F530

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Skip

Skip

Skip

Skip

Skip

Skip

Skip

Skip

 

 

 

 

 

 

 

 

 

 

1

1

1

1

1

1

1

1

 

 

 

 

 

 

 

 

 

 

2

2

2

2

2

2

2

2

 

 

 

 

 

 

 

 

 

Number

3

3

3

3

3

3

3

3

 

 

 

 

 

 

 

 

4

4

4

4

4

4

4

4

 

 

 

 

 

 

 

 

5

5

5

5

5

5

5

5

 

 

 

 

 

 

 

 

6

6

6

6

6

6

6

6

Speed

 

 

 

 

 

 

 

 

7

7

7

7

7

7

7

7

 

 

 

 

 

 

 

 

8

8

8

8

8

8

8

8

 

 

 

 

 

 

 

 

Preset

9

9

9

9

9

9

9

9

 

 

 

 

 

 

 

 

10

10

10

10

10

10

10

10

 

 

 

 

 

 

 

 

11

11

11

11

11

11

11

11

 

 

 

 

 

 

 

 

 

 

12

12

12

12

12

12

12

12

 

 

 

 

 

 

 

 

 

 

13

13

13

13

13

13

13

13

 

 

 

 

 

 

 

 

 

 

14

14

14

14

14

14

14

14

 

 

 

 

 

 

 

 

 

 

15

15

15

15

15

15

15

15

 

 

 

 

 

 

 

 

 

172

H9 ASD Installation and Operation Manual

Page 180
Image 180
Toshiba H9 operation manual F523, Pattern Group 1 Selection, Program ⇒ Pattern Run ⇒ Speeds