RX2 (AI1) Input Bias, 163

RX2 (AI1) Input Gain, 163

RX2 (AI1) Input Point 1 Frequency, 117 RX2 (AI1) Input Point 1 Rate, 118 RX2 (AI1) Input Point 1 Setting, 116 RX2 (AI1) Input Point 2 Frequency, 117 RX2 (AI1) Input Point 2 Rate, 119 RX2 (AI1) Input Point 2 Setting, 117

S

S/L2, 16

S1, 21, 22

S2, 21, 22

S3, 21, 22

S4, 21, 22

Save User Settings, 75

Second Speed Loop Proportional Gain, 160

Second Speed Loop Stabilization Coefficient, 161

Send Wait Time (2-wire), 206

Setpoints, 59

Short Circuit Detection At Start, 185

Short Circuit Protection, 267

Simple Positioning Completion Range, 151

Sink, 24

Sink/Source Setting Error, 250, 251

Slip Frequency Gain, 151

Source, 24

SOUT, 254

S-Pattern 1, 165

S-Pattern 2, 165

S-Pattern Acceleration Lower Limit Adjustment, 168

S-Pattern Acceleration Upper Limit Adjustment, 168

S-Pattern Deceleration Lower Limit Adjustment, 168

S-Pattern Deceleration Upper Limit Adjustment, 168

Special, 56

Special Parameters, 57

Special Protection Parameters, 53

Speed 1 Operation Time, 177

Speed 10 Operation Time, 178

Speed 11 Operation Time, 178

Speed 12 Operation Time, 178

Speed 13 Operation Time, 179

Speed 14 Operation Time, 179

Speed 15 Operation Time, 179

Speed 2 Operation Time, 177

Speed 3 Operation Time, 177

Speed 4 Operation Time, 177

Speed 5 Operation Time, 177

Speed 6 Operation Time, 177

Speed 7 Operation Time, 178

Speed 8 Operation Time, 178

Speed 9 Operation Time, 178

Speed at 0% Drooping Gain, 139

Speed at F320 Drooping Gain, 139

Speed Limit (torque=0) Band, 157

Speed Limit (torque=0) Center Value, 156

Speed Limit (torque=0) Center Value Reference, 156

Speed Loop Proportional Gain, 160

Speed Loop Stabilization Coefficient, 160

Speed PID Switching Frequency, 161

Speed Reach Detection Band, 86

Speed Reach Frequency, 86

Speed Reference Setpoints, 55, 56

ST, 21, 22

Stall, 53

Stall Prevention During Regeneration, 160

Stall Prevention Factor 1, 154

Stall Prevention Level, 182

Standard Mode Selection, 46

Start Frequency, 123

Startup and Test, 27

Startup Wizard Parameter Requirements, 71

Stepout Current Detection Level, 192

Stepout Current Detection Time, 192

StopReset Key, 30

SU+, 21, 23

Supply Voltage Correction, 137

SW301, 23

Switching Load Torque During Power Running, 142

Switching Load Torque During

Regenerative Braking, 142

Synchronized Acceleration Time, 139

Synchronized Deceleration Time, 138

System Configuration and Menu Options, 41

System Grounding, 18

System Integration Precautions, 7

System Operation, 70

T

T/L3, 16

Tension Torque Bias Input, 154 Terminal, 47

Terminal Board, 21, 24 Terminal Descriptions, 22 Thermal derating, 190

Time Limit For Lower-Limit Frequency Operation, 125 Torque, 44, 59

Torque Bias Input Selection, 143

Torque Command Selection, 154 Torque Control, 59, 60 Torque Current, 44

Torque Limit Settings, 60 Torque Reference, 44 Torque Speed Limiting, 60

H9 ASD Installation and Operation Manual

279

Page 287
Image 287
Toshiba H9 operation manual 279