Etn, None | Toshiba H9 manual

LED Display	LCD Display		Possible Causes


ETN		•	Autotune readings that are significantly inconsistent with the configuration
	Autotune Error		information.
		• A non-3-phase motor is being used.
		• Incorrect settings at F400 or F413.
		• Using a motor that has a significantly smaller rating than the ASD.
		• ASD output cabling is too small, too long, or is being housed in a cable tray
			with other cables that are producing an interfering EMF.
		• Motor is running during the Autotune function.

ETN1		•	F402 adjustment required (Motor temperature is too high).
		• F410 adjustment required (Motor Constant 1 improperly set).

ETN2		•	F412 adjustment required (Motor Constant 3 improperly set).

ETN3		•	Autotune setting F400 is set to Auto Calculation and there is a problem with
			the Motor Constant readings.

ETYP		•	Firmware information (typeform) loaded into the Gate Driver board is
	Typeform Error		inconsistent with the device in which the firmware is being used.
		• The Gate Driver board has been replaced.
		• The Gate Driver board is defective.

None	No Errors	•	No active faults.

OC1		•	Improper V/f setting.
	Overcurrent During	• Restart from a momentary power outage.
	Acceleration	• Restart from a momentary power outage.
	Acceleration
		• The ASD is starting into a rotating motor.
		• ASD/Motor not properly matched.
		•	Phase-to-phase short (U, V, or W).
		• Accel time too short.
		• Voltage Boost setting is too high.
		•	Motor/machine jammed.
		• Mechanical brake engaged while the ASD is running.
		• ASD current exceeds 340% of the rated FLA on ASDs that are 100 HP or
			less during acceleration. On ASDs that are greater than 100 HP, this fault
			occurs when the ASD current exceeds 320% of the rated FLA during
			acceleration.

OC1P		•	Cooling fan inoperative.
	Overheat During	• Ventilation openings are obstructed.
	Acceleration	• Ventilation openings are obstructed.
	Acceleration
		• Internal thermistor is disconnected.
		• Acceleration time is too short.
		•	Improper V/f setting.
		• ASD or the motor is improperly matched to the application.

252	H9 ASD Installation and Operation Manual

Image 260

Toshiba H9 operation manual Etn, None

Contents

Installation and Operation Manual Page H9 Adjustable Speed Drive Introduction Important Notice About This Manual Manual’s Purpose and Scope Contacting Toshiba’s Customer Support Center Toshiba International Corporation Table of Contents 246 256263 265 Signal Words General Safety InformationSafety Alert Symbol Qualified Personnel Special SymbolsEquipment Warning Labels Disposal Equipment InspectionHandling and Storage Mounting Requirements Installation PrecautionsLocation and Ambient Requirements Grounding Capacitor Switch Conductor Routing and Grounding Power Connections Protection System Integration Precautions Personnel Protection System Setup Requirements Operational and Maintenance Precautions Motor Characteristics Motor/Load Combinations Power Factor CorrectionLight Load Conditions Load-produced Negative Torque Motor Braking H9 ASD Characteristics Using Vector ControlOver-current Protection ASD Capacity Installation and Connections Installation Notes Typical circuit breaker configuration Mounting the H9 ASD Connecting the H9 ASD Power Connections Power Connection Requirements System Grounding Grounding CapacitorPage Lead Length Specifications ModelNema MG-1-1998 Section IV Part Frequency Compliant Motors Circuit Config ControlTerm. Name Input/Output O1A/B OUT1 Terminal Descriptions Page TB1 TB2 TB3 Circuit Configurations Discrete Input Typical Connection Diagram H9 ASD typical connection diagram Startup and Test EOI Operation EOI Remote Mounting EOI Features H9 ASD Electronic Operator Interface features LED Display LED/LCD Display Information LCD Display Active Frequency LED/LCD Display Installation Note Remote Keypad Required Hardware Keypad Installation PrecautionsKeypad Remote Mounting Keypad Mounting Dimensions Keypad Remote Mounting w/o the ASD-MTG-KIT Keypad Remote Mounting using the ASD-MTG-KIT Keypad Bezel Plate Mounting Dimensions Command Mode and Frequency Mode Control Command Control F003 Command and Frequency Control Selections Frequency Control F004 Override Operation Command Control Selections Frequency Control Selections Binary/BCD Input Option Root Menus System Configuration and Menu OptionsFrequency Command Mode EOI Command Mode Monitor Mode FrequencyPage Main Monitor Selections Settings Frequency SettingsStandard Mode Accel/Decel #1 Input Terminal Delays Analog OutputTerminals Input Special Line Power Switching Input Terminals Reach Settings Output TerminalsDisplay Parameters Prohibition Alarm Prohibition Type ResetReal-time Clock Setup Trip History read-only Contrast Changed From DefaultTrip History Low Current Settings Main MonitorSelections View Trace Data Phase Loss Trip SettingsOvertorque Parameters Disable Jog SettingsPreset Speeds Analog Filter Speed Reference Setpoints Crane/Hoist Settings Acc/Dec #1 #4Acc/Dec Special Carrier Frequency Five Point Setting Frequency ControlSpecial Parameters Jump Frequencies Operation Panel TraverseMotor Set #2 Motor Set #3 Torque Control Vector Motor ModelManual Torque Limit Torque Limit Settings Feedback SettingsTorque Speed Limiting PG Settings Override ControlMy Function Selection My Function Unit F906 My Function Monitor My Function DataMy Function Analog Adjustments Communication Preset Speed Ethernet SettingsOperation Mode Group F571 Operation Time Pattern Run Enter Password Change PasswordSpeeds Lockouts Initial Setup Run Next Time? ⇒ Go to Program ModeSystem Operation Startup Wizard Parameters Manually Configure the ASD Startup Wizard Parameter Requirements Motor RPM Operation Local Display Unit Default Setting Changes Changed From Default screen Save User Settings Direct Access Parameters/Numbers F000 F001Automatic Acceleration/Deceleration Automatic Torque Boost Command Mode F004 FM Output Terminal Adjustment FM Terminal Setup ParametersF005 F006 FM Output Terminal Function Direct Access Number F007 Direct Access Number F008F007 F008 Forward/Reverse Run Selection F009 Acceleration TimeAcceleration Deceleration Time F012 F015 Upper Limit FrequencyLower Limit Frequency Pattern Motor Overload Protection Configuration Direct Access Number F016F016 F017 Manual Torque Boost Preset Speed Preset Speed Truth TablePreset Output F018 F019 F020 F024 Direct Access Number F040 F040Automatic Function Selection Program ⇒ Utilities ⇒ Display Parameters Low-Speed Signal Output Frequency F100 F105Speed Reach Frequency Speed Reach Detection Band Direct Access Number F106 Direct Access Number F107F106 F107 Input Terminal Priority F109 F114 Direct Access Number F119 Direct Access Number F120F119 F121 Input Terminal 9 LI1 Function F122 F124 Input Terminal 12 LI4 FunctionInput Terminal 13 LI5 Function Input Terminal 14 LI6 Function F125 F131 Input Terminal 15 LI7 FunctionInput Terminal 16 LI8 Function Output Terminal 1 OUT1 Function F132 F134 Output Terminal 3 FL FunctionOutput Terminal 4 OUT3 Function Output Terminal 5 OUT4 Function Output Terminal 6 R1 Function Direct Access Number F135F135 F137 F138 F142 Output Terminal 9 R2 FunctionInput Terminal 1 F Response Time Input Terminal 2 R Response Time F143 F165 F166 F169 Input Terminal 19 B14 FunctionInput Terminal 20 B15 Function Output Terminal 10 R3 Function Motor Overload Protection Level F170 F173Base Frequency Voltage Direct Access Number F174 Direct Access Number F175Direct Access Number F176 F174 F177 Direct Access Number F178 Direct Access Number F179Direct Access Number F180 F178 F181 Five-Point Setting Frequency Program ⇒ Special ⇒ V/f Five-Point SettingDirect Access Number F190 F190 Five-Point Setting Voltage Direct Access Number F191Direct Access Number F192 F191 F192 F193 F197 Direct Access Number F198 Direct Access Number F199Direct Access Number F200 F198 F200 Input Point 1 Setting Input Speed Control SetupF201 Speed Control Input Point 2 Setting F202 F204Input Point 1 Frequency Input Point 2 Frequency Input Torque Control Setup F205Input Point 1 Rate Torque Control Input Point 2 Rate Frequency Mode Priority Switching FrequencyF206 F208 Direct Access Number F209 F209Analog Input Filter Program ⇒ Frequency ⇒ Analog Filter RR Input Point 1 Setting RR Input Speed Control SetupF210 RR Input Point 1 Frequency RR Input Point 2 Setting Direct Access Number F212Direct Access Number F213 F212 F213 RR Input Torque Control Setup F214 F215RR Input Point 1 Rate RR Input Point 2 Rate RX Input Point 1 Setting RX Input Speed Control SetupF216 F217 RX Input Point 1 Frequency RX Input Point 2 Setting Direct Access Number F218Direct Access Number F219 F218 F219 RX Input Torque Control Setup F220 F221RX Input Point 1 Rate RX Input Point 2 Rate F222 RX2 AI1 Input Point 1 SettingRX2 AI1 Input Speed Control Setup RX2 AI1 Input Point 2 Setting F223 F225RX2 AI1 Input Point 1 Frequency RX2 AI1 Input Point 2 Frequency RX2 AI1 Input Point 1 Rate RX2 AI1 Input Torque Control SetupF226 RX2 AI1 Input Point 2 Rate Direct Access Number F227F227 F228 BIN Input Point 1 SettingBIN Input Speed Control Setup BIN Input Point 2 Setting F229 F231BIN Input Point 1 Frequency BIN Input Point 2 Frequency PG Input Point 1 Setting PG Input Speed Control SetupF234 F235 PG Input Point 1 Frequency PG Input Point 2 Setting F236 F241PG Input Point 2 Frequency Start Frequency F242 F251 F252 F256 Jog Setup and Execution Set the Command Mode Selection F003 to EOI KeypadDirect Access Number F260 F260 Panel Operation Jog Mode Direct Access Number F261Direct Access Number F262 F261 F262 Setup Requirements Direct Access Number F264Up/Down Frequency up Mode Up/Down Frequency down Mode F264 F265 F269 Program ⇒ Special ⇒ Jump Frequencies Direct Access Number F270F270 F271 F287 Jump Frequency 1 BandwidthJump Frequency 2 Bandwidth Jump Frequency 3 Bandwidth F288 F293 Auto Restart Selection F294PWM Carrier Frequency Regenerative Power Ridethrough Mode Ridethrough Setup RequirementsF302 Program ⇒ Protection ⇒ Undervoltage/Ridethrough Retry Selection Direct Access Number F303F303 F304 F305 Overvoltage Limit Operation F307 F310 Supply Voltage CorrectionDynamic Braking Resistance Continuous Dynamic Braking Capacity Forward Run/Reverse Run Disable Random ModeCarrier Frequency Control Mode F311 F317 F318 F322 F323 F329 Drooping Insensitive TorqueDrooping Output Filter Light-Load High-Speed Operation F330 F334 F335 F341 F342 F346 F347 F349 Creeping TimeBraking Time Learning Function Accel/Decel Suspend F350 F353 Acceleration Suspend FrequencyAcceleration Suspend Time Deceleration Suspend Frequency Commercial Power/ASD Output Switching Program ⇒ Terminal ⇒ Line Power SwitchingSwitching Setup Requirements F354 F355 F359 F360 F364 F365 F370 F371 F376 Autotuning F377 F401PG Disconnection Detection Simple Positioning Completion Range F402 F409 Motor Rated CapacityMotor Rated Current Motor Rated RPM F410 F415 Torque Command Selection F416 F423Stall Prevention Factor Tension Torque Bias Input F424 F426 Load Sharing Gain InputForward Speed Limit Input Forward Speed Limit Level F427 F431 Reverse Speed Limit InputReverse Speed Limit Input Level Speed Limit torque=0 Center Value Reference Power Running Torque Limit Power Running Torque Limit 1 LevelF432 F441 Speed Limit torque=0 Band F442 F446 F447 F452 F453 F463 Speed PID Switching Frequency F464 F471Second Speed Loop Stabilization Coefficient Input Bias F472 F475 RR Input BiasRR Input Gain RX Input Bias F476 F479 RX2 AI1 Input BiasRX2 AI1 Input Gain AI2 Option V/I Input Bias Direct Access Number F500 Direct Access Number F501F498 F501 Permanent Magnet PM Motor Constant Program ⇒ Special ⇒ Accel/Decel #1 #4 Settings Direct Access Number F502F502 Acc/Dec Pattern Direct Access Number F503 F503 Acc/Dec Pattern 1 Accel/Decel Switching FrequencyF504 F505 Pattern Acceleration Lower Limit Adjustment Pattern Acceleration Upper Limit AdjustmentPattern Deceleration Lower Limit Adjustment Pattern Deceleration Upper Limit Adjustment Acceleration/Deceleration Pattern Acceleration/Deceleration Switching FrequencyF511 F514 Pattern Operation Selection Pattern Operation ModeF515 F521 Pattern 1 Repeat Direct Access Number F522F522 Program ⇒ Pattern Run ⇒ Speeds F523Pattern Group 1 Selection Direct Access Number F524 Direct Access Number F525Direct Access Number F526 Direct Access Number F527 F528 F531 Pattern 2 Repeat F532 F535 Pattern Group 2 Selection Direct Access Number F536 Direct Access Number F537Direct Access Number F538 Direct Access Number F539 F540 F545 F546 F551 Preset Speed Operation Mode F552 F560Speed 13 Operation Time Speed 14 Operation Time Preset Speed 1 Operation Mode Preset Speed 2 Operation ModePreset Speed 3 Operation Mode F561 F563 F564 F573 Preset Speed 14 Operation Mode Preset Speed 15 Operation ModeRetain Trip Record at Power Down F574 F602 Emergency Off Mode Settings ASD Output Phase Failure DetectionF603 F605 Emergency Off DC Injection Application Time F606 F610 F611 F615 Low Current Detection ThresholdLow Current Trip Threshold Time Short Circuit Detection At Start F616 F621 F622 F627 Regenerative Power Ridethrough Control Level F628 F630Undervoltage Trip Detection Time Brake Answer Wait Time Direct Access Number F631 Factory Default Thermal Detection + OverloadF631 ASD Overload 460-Volt Carrier Frequency/Thermal Derating Specifications Analog Input Broken Wire Detection Level Annual Average Ambient TemperatureF633 F637 Rush Relay Current Activation Time F638 F641 PTC2 Thermal SelectionBraking Resistance Overload Time 10x rated torque Step-Out Current Detection Level Direct Access Number F660 Direct Access Number F661F660 F661 Adding Input Selection AM Output Terminal Adjustment AM Terminal Setup ParametersF669 F671 Selection of OUT Terminal MON1 Terminal Adjustment F672 F674MON1 Terminal Meter Selection MON2 Terminal Meter Selection F675 F682 F683 F689 F690 F700 Display Gradient Characteristic F701 F705Display Units for Voltage and Current Display Unit Multiplication Factor Operation Command Clear Selection When ST Off F706Display Bias Change Step Selection F721 F729 F730 F737 F740 F742 Trace SelectionTrace Cycle Trace Data F743 F801 Baud Rate RS485 2-wireParity RS485 2- and 4-wire Communications Time Out Time RS485 2- and 4-wire Communications Time-Out Action RS485 2- and 4-wireF802 F804 ASD Number Send Wait Time RS485 2-wire ASD-to-ASD Communications RS485 2-wireRS485 2-Wire Protocol Selection F805 F807 Point 1 Setting Gain and Bias SettingsF810 F812 Frequency Point Selection Point 2 Setting Baud Rate RS485 4-wireRS485 Send Wait Time RS485 4-wire F813 F825 ASD-to-ASD Communications RS485 4-wire RS485 4-Wire Protocol Selection TSB/ModBusCommunications Option DeviceNet/Profibus Setting F826 F830 F831 F836 F841 F844 Preset Speed Operation Selection F845 F853Disconnection Detection Extended Time ASD Operation at Disconnect Communications Option Speed Switch Monitor DeviceNet F854 F871CC-Link Block Write Data Direct Access Number F875 Direct Access Number F876Direct Access Number F877 F875 F877 Network Option Reset Settings Input Function CommandF878 F901 Free Notes F902 F905 Output Function Assigned F906 F910 F911 F915 F916 F919 My Function Percent Data F920 F925 My Function Frequency Data F926 F930 My Function Time Data F931 F935 My Function Count Data F936 F940 F941 F945 F946 F950 Direct Access Number F951 Direct Access Number F952Direct Access Number F953 Direct Access Number F954 Direct Access Number F955 Direct Access Number F956Direct Access Number F957 Direct Access Number F958 Analog Function Assigned Object F959 F962Analog Input Function Target Monitor Output Function Monitor Output Function CommandF964 F966 Direct Access Number F967 Direct Access Number F968Direct Access Number F969 F967 F969 Direct Access Number F970 Direct Access Number F971Direct Access Number F972 F970 F971 F973 F976 Virtual Input Terminal 1 SelectionVirtual Input Terminal 2 Selection Virtual Input Terminal 3 Selection Setup example F977My Function Combined Terminal Function 234 F980 F984 Terminal Selection Descriptions Sel. No External Over-heat Causes an Over-Heat Trip OH PID Differentiation/Integration Clear Clears the PID value No NC Selections My Function Input Target selections Selection Communications Terminal Assignment Number Setting Input Param Function Trace Back Data Selections Comm Monitor Number Input Setting/Communication Number Function Resolution My Function Operator selections F928 F932 for My Function Data Alarms, Trips, and Troubleshooting Alarms and Trips Alarms User Notification CodesAtn DbOn Type Reset required select Clear run timer Dynamic Braking Resistor PtSt With the Low-current Trip Trips/Faults LED Display LCD Display Possible Causes 50/E-51 EF1/EF2 ETN None OCA3 or OCL OCA1 or OCLOCA2 or OCL OP1 Viewing Trip Information Clearing a Trip Enclosure Dimensions and Conduit Plate Information Enclosure Dimensions 410K 412K 415K420K 425K See Tables 16 and 17 for actual dimensions 259 260 261 See for the associated device. Dimensions are in in/cm Current/Voltage Specifications Ph VariableMotor HP VT130H9U Continuous Seconds ± 2 Hz Frequency 4055 4080 41604220 4270 Cable/Terminal/Torque Specifications Wire/Cable Size Lug Size Range Terminal Board TorqueMCP Rating AWG or kcmil Number Amps VT130H9U Model 4270 4330 4400 In-Lbs./Nm4055 Short Circuit Protection Recommendations Dynamic Braking Resistor Wire/Cable Specifications 269 H9 ASD Optional Devices Part Identifier Device Name Device Function Index 272 273 274 275 276 277 278 279 280 Toshiba