|
|
|
|
| User Interface Commands for the UltraNet Edge 3000 | ||
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
| |||
| TANKIO | The TANKIO user interface provides information regarding the |
|
| |||
|
| circuit across the WAN. For further information on the TANKIO user |
|
| |||
|
| interface commands, refer to the TANKIO commands section in the |
|
| |||
|
| UltraNet Edge Storage Router Command Reference. The following |
|
| |||
|
| sections highlight the commands useful for troubleshooting. |
|
| |||
| tankio stats | This command displays the current status and statistics of the WAN. |
|
| |||
|
| Example of tankio stats command screen display: |
|
| |||
|
| # St Bus Vid InPackts InOctets RcvC RecvOOSq OutPckts |
|
| |||
|
| OutOctts XmtC ReXmitCt |
|
| |||
|
| 1 Up 090 090 000001be 00000000 0000 00000003 000001c9 |
|
| |||
|
| 00000000 | 0000 | 00000000 |
|
|
|
|
|
|
| 0000e6a8 |
|
| |
|
| 00010528 |
|
|
|
|
|
|
| The status of the circuit is found in the St field. Up indicates that the |
|
| |||
|
| circuit is established with the peer node. Down indicates that the |
|
| |||
|
| circuit is not established with the peer node. |
|
| |||
|
| 1. If the circuit status is down, first check the physical interface to |
|
| |||
|
| make sure the interface link is up. See either the “AMDENET |
|
| |||
|
| 10/100 WAN or Maintenance Interface” section or the “GNIC3 |
|
| |||
|
| Gigabit Ethernet WAN” section. |
|
| |||
|
| 2. If the interface link is up, check the IP addresses, the subnet mask, |
|
| |||
|
| the default gateway, and the static routes. These all need to be |
|
| |||
|
| correct for the circuit to come up. |
|
| |||
|
|
|
|
| |||
| ARP | The ARP user interface provides information about devices |
|
| |||
|
| physically attached to all of the Ethernet interfaces. For further |
|
| |||
|
| information on the ARP user interface commands, refer to the ARP |
|
| |||
|
| commands section in the UltraNet Edge Storage Router Command |
|
| |||
|
| Reference. The following sections highlight the commands useful for |
|
| |||
|
| troubleshooting. |
|
|
|
| |
| arp tbl | This command displays the IP address of the Ethernet maintenance |
|
| |||
|
| interface, the WAN Ethernet interface, and the devices that are |
|
| |||
|
| attached to them. |
|
| |||
|
| tm.0x10> arp |
|
| |||
|
| arp1.0x10> tbl |
|
| |||
|
| Example of the arp tbl command screen display: |
|
| |||
|
| instance 1 (ethernet1) (10/100 Ethernet maintenance interface) |
|
| |||
|
|
|
|
| Troubleshooting and Diagnostics |
| |
|
|
|
|
| |||
|
|
|
|
|
|
|
|
13
