Configuring language support using the Srem | Nortel Networks 4050

Chapter 9 Customizing the portal and user logon 421

Configuring language support using the SREM

To manage language definition files in the system, perform the following steps:

1Select the System > Language tab.

The Languages sub-tabs appear (see Figure 107).

Figure 107 Pre-defined Languages

2Choose from one of the following tasks:

•“Viewing predefined languages” on page 421

•“Viewing and removing custom languages” on page 421

•“Importing and exporting language definitions” on page 422

Nortel Secure Network Access Switch 4050 User Guide

Image 421

Nortel Networks 4050 manual Configuring language support using the Srem, Select the System Language tab

Contents

Nortel Secure Network Access Switch 4050 User Guide 320818-A Copyright Nortel Networks Limited 2005. All rights reserved Licensing Nortel Secure Network Access Switch 4050 User Guide General Contents Contents Managing the network access devices Configuring the domain Configuring groups and profiles Configuring authentication 233 TunnelGuard SRS Builder Managing system users and groups Customizing the portal and user logon Setting the portal display language using the CLI Configuring system settings Adding a host interface Managing certificates Configuring Snmp Maintaining and managing the system Upgrading or reinstalling the software Appendix a CLI reference Troubleshooting 837 Appendix C Supported MIBs Appendix H Software licensing information Index Contents 320818-A Preface Before you begin Connect the switch to the networkPreface Bold text Text conventions Publications Related informationPlain Courier text Example Set Trap Monitor Filters Online How to get help Preface This chapter includes the following topics Nortel SNA solution Supported users Elements of the Nsna solutionOverview Role of the Nortel Snas Nortel SNA VLANs and filters Nortel Snas 4050 functions Groups and profiles Authentication methods TunnelGuard host integrity check About SSH Communication channelsCommunication channels in the Nortel SNA network RSA DSA Nortel Snas 4050 clusters One-armed and two-armed configurations Two-armed configuration One-armed configuration Illustrates a two-armed configuration Nortel SNA configuration and management tools Configure the network Dhcp server Nortel Snas 4050 configuration roadmap Overview Overview Overview Overview Overview 320818-A Chapter Initial setup Initial setup Management IP address About the IP addressesPortal Virtual IP address Log on using the following username and password Initial setupLogin admin Password admin Real IP address Select the option for a new installation Setup Menu displaysEnter port number for the management interface Enter Vlan tag id or zero for no Vlan Enter network mask 255.255.255.0 mask Enter default gateway IP address or blank to skip Setup a two armed configuration yes/no no Enter port number for the traffic interface Specify the MIP for this device or clusterEnter IP address for this machine on traffic interface Enter a timezone or select select timezone Specify the NTP server, if applicable Configure the time settingsSpecify the DNS server, if applicable Enter NTP server address or blank to skip IPaddr Specify the pVIP of the Nortel Snas 4050 device Change the admin user password, if desiredSpecify a name for the Nortel Snas 4050 domain Create http to https redirect server no Settings created by the quick setup wizard Extended profile details Adding a Nortel Snas 4050 device to a cluster Before you begin Select the option to join an existing cluster Joining a cluster Enter network mask 255.255.255.0 mask Specify the MIP of the existing cluster Enter the existing admin user password password Next steps Setup successful Login Applying and saving the configuration Applying and saving the configuration using the Srem Applying and saving the configuration using the CLICfg/dump Cfg/ptcfg Apply and Commit buttons Initial setup 320818-A Chapter Managing the network access devices Managing the network access devices Roadmap of domain commands Managing network access devices using the CLI Reset Using the quick switch setup wizard Adding a network access device using the CLISpecify the IP address of the network access device Cfg/domain 1/quick Nsna communication port5000 Go to on To continue, go to on Red vlan id of Switch Vlan ID Switch menu displays Manually adding a switchCfg/domain #/switch switch ID Cfg/domain #/switch #/dis Cfg/domain #/switch #/delete Deleting a network access device using the CLI Configuring the network access devices using the CLI Cfg/domain #/switch switch ID followed by Switch menu includes the following optionsIp IPaddr Cfg/domain #/switch #/vlan Mapping the VLANs using the CLIFollowed by Dis Delete Cfg/domain #/switch #/vlan followed by Domain vlan or Switch vlan menu displaysCfg/domain #/switch #/vlan/list Add name Vlan ID Managing SSH keys using the CLI For an Ethernet Routing Switch 5510, 5520, or Generating SSH keys for the domain using the CLINsnas SSH key menu displays Cfg/domain #/sshkey Nsnas SSH key menu includes the following options Cfg/domain #/switch #/sshkey/exportCfg/domain #/sshkey followed by Main# /cfg/domain 1/sshkey Shows sample output for the /cfg/domain #/sshkey command Cfg/domain #/switch #/sshkey followed by Cfg/domain #/switch #/sshkeyCfg/domain#1/sshkey/export command to Monitoring switch health using the CLI Reimporting the network access device SSH key using the CLICfg/domain #/switch #/hlthchk Enter Apply to apply the change immediately Cfg/domain #/switch #/dis Cfg/domain #/switch #/hlthchk followed byHealthCheck menu includes the following options Deadcnt count Adding a network access device using the Srem Managing network access devices using the SremTo add a network access device, use the following steps Cfg/domain #/switch #/ena Add a Switch fields Add a Switch Configuring the network access devices using the Srem Deleting a network access device using the Srem Switch Configuration screen 320818-A Switch Configuration screen appears see Figure Switch Configuration fields You can perform the Vlan mapping in two ways Mapping the VLANs using the Srem Domain VLANs screen Mapping VLANs by domain To add VLANs to a domain, complete the following steps Adding VLANs to a domainClick Add Add a new Vlan dialog box appears see Figure Add a new Vlan fields Removing VLANs from a domain Switch VLANs screen Mapping VLANs by switch To add VLANs to a switch, complete the following steps Adding VLANs to a switch Removing VLANs from a switch Managing SSH keys using the Srem Managing the network access devices Managing the network access devices Key Generation screen appears see Figure Generating SSH keys for the domain using the Srem Switch SSH Key fields Exporting SSH keys for the domain using the Srem Export Key screen appears see Figure Export Key fields Click Apply on the toolbar to begin the export process Switch SSH Key screen appears see Figure Managing SSH keys for Nortel SNA communication using Reimporting the network access device SSH key using the Srem Switch SSH Key screen appears see on Monitoring switch health using the SremClick Delete Switch SSH Key Click Import SSH from Switch Health Check screen 320818-A Health Check screen appears see Figure Viewing a connected client list using the Srem Connected Clients fields Managing the network access devices Switch Configuration screen Chapter Configuring the domain Configuring the domain Configuring the domain using the CLICfg/domain Captive portal Portal look and feel Linksets Logging traffic with syslog messages Details onoff Manually creating a domain using the CLI Creating a domain using the CLIYou can create a domain in two ways Cfg/domain domain ID 320818-A Main# /cfg/domain Using the Nortel Snas 4050 domain quick setup wizardCfg/quick Main# cfg/quick Specify the certificate to be used by the portal server Configuring the domain Specify whether the SSL server uses chain certificates Do you want to configure a switch? yes/no noDo you require chain certificates yes/no no Do you want an http to https redirect server yes/no no Do you want to create a tunnelguard test user? yes/no yes Configuring the domain To delete a domain, use the following command Deleting a domain using the CLICfg/domain #/del To configure the domain, use the following command Configuring domain parameters using the CLICfg/domain domain ID followed by Pvips IPaddr Httpredir TG menu displays TG menu includes the following options Configuring the TunnelGuard check using the CLICfg/domain #/aaa/tg Cfg/domain #/aaa/tg followed by Cfg/domain #/aaa/tg/status-quo Cfg/domain #/aaa/tg/quick Using the quick TunnelGuard setup wizard in the CLI TunnelGuard quick setup wizard creates a default SRS rule Configuring the SSL server using the CLIServer 1001 menu displays Main# /cfg/domain #/aaa/tg/quick Server 1001 menu includes the following options Tracing SSL traffic using the CLICfg/domain #/server followed by Interface ID Ssldump Output mode Cfg/domain #/server/trace followed by Cfg/domain #/adv/interface commandTcpdump Ping host SSL Settings menu displays Configuring SSL settings using the CLIDnslookup host Traceroute host Cfg/domain #/server/ssl followed by SSL Settings menu includes the following optionsCert certificate Index Index list Cachain certificateYes Cfg/domain #/server/ssl/protocol Ena Dis Configuring traffic log settings using the CLI Traffic Log Settings menu includes the following options Traffic Log Settings menu displaysCfg/domain #/server/adv/traflog Cfg/domain #/server/adv/traflog followed by Cfg/domain #/httpredir Configuring Http redirect using the CLICfg/domain #/httpredir followed by Redir onoff Cfg/sys/host #/interface command see Configuring advanced settings using the CLICfg/domain #/adv Cfg/domain #/adv followed by Configuring Radius accounting using the CLI Radius Accounting Servers menu displays Managing Radius accounting servers using the CLICfg/domain #/aaa/radacct Cfg/domain #/aaa/radacct followed by Cfg/domain #/aaa/radacct/servers followed by NSNAS-Portal-ID VPN Attribute menu displaysCfg/domain #/aaa/radacct/vpnattribu VPN Attribute menu includes the following options Configuring the domain using the SremCfg/domain #/aaa/radacct/vpnattribu followed by Vendorid Creating a domain using the Srem Secure Access Domain Table screen 320818-A Manually creating a domain using the Srem Add a Secure Access Domain fields Add a Secure Access Domain Using the Srem Domain Quick Wizard Configuring the domain Click Domain Quick Wizard Domain Quick Wizard General Settings fieldsClick Next Domain Quick Wizard Certificate fields Domain Quick Wizard Certificate Organization name and do not use any of the following Domain Quick Wizard Certificate Chain fields Domain Quick Wizard Certificate Chain Domain Quick Wizard Server fields Domain Quick Wizard Server dialog box appears see Figure Domain Quick Wizard Switch fields Domain Quick Wizard Switch dialog box appears see Figure Domain Quick Wizard Tunnel Guard fields Domain Quick Wizard Tunnel Guard dialog box appears see To delete a domain, perform the following steps Deleting a domain using the Srem To configure a domain, perform the following steps Configuring domain parameters using the Srem Domain Configuration fields Domain domain Configuration screen Additional domain configuration in the SremAdditional domain configuration tabs Component Description Additional domain tree components Configuring the TunnelGuard check using the Srem TunnelGuard Configuration screen appears see Figure TunnelGuard Configuration fields Groups using the Srem on TunnelGuard Quick Setup screen appears see Figure Using the TunnelGuard Quick Setup in the Srem TunnelGuard Quick Setup fields Server Configuration screen 320818-A Configuring the SSL server using the Srem Server Configuration fields Server SSL Settings screen 320818-A Configuring SSL settings using the Srem ALL@STRENGTH Server SSL Settings fields Configuring the domain Server SSL Settings fields Configuring traffic log settings using the Srem Traffic Log Syslog Settings screen appears see Figure Traffic Log Syslog Settings fields Tracing SSL traffic using the Srem Configuring Http redirect using the Srem Http Redirect screen 320818-A Http Redirect fields Configuring Radius accounting using the Srem Configuring Nortel Snas 4050-specific attributes using Radius accounting Configuration screen appears see Figure Adding a Radius accounting server using the Srem Managing Radius accounting servers using the SremRadius accounting Configuration fields Radius Accounting Servers screen Radius Accounting Servers screen appears see Figure Radius Accounting Server fields Moving a Radius accounting server using the Srem Deleting a Radius accounting server using the Srem Configuring the domain 320818-A Chapter Configuring groups and profiles Overview Configuring groups and profilesGroups This section includes the following topics Default group TunnelGuard SRS rule Linksets Extended profiles Create the SRS rules see TunnelGuard SRS Builder on Configuring groups and extended profiles using the CLI Roadmap of group and profile commands To create and configure a group, use the following command Configuring groups using the CLICfg/domain 1/aaa/group group ID Restrict Cfg/domain 1/aaa/group # followed byExtend profile ID Comment comment Tgsrs SRS rule nameMain# /cfg/domain 1/AAA/group Cfg/domain 1/aaa/filter filter ID Configuring client filters using the CLI Cfg/domain 1/aaa/filter filter ID followed by Client Filter menu includes the following optionsTg truefalseignore Main# /cfg/domain 1/AAA/filter Configuring extended profiles using the CLICfg/domain 1/aaa/group group IDgroup name/extend Cfg/domain 1/aaa/group #/extend # followed by Extended Profile menu includes the following optionsFilter name Vlan name Linkset Del Cfg/domain 1/aaa/group #/extend #Main# cfg/domain 1/aaa/group 2/extend Extended Profile 1# ../extend 2/filter tgfailed/vlan Yellow Cfg/domain 1/aaa/group #/linkset Mapping linksets to a group or profile using the CLICfg/domain 1/aaa/group #/extend #/linkset Cfg/domain 1/aaa/group #/extend #/linkset followed by Linksets# add example2 Main# cfg/domain 1/aaa/group 1/linksetLinksets# insert 2 example3 Creating a default group using the CLI Configuring groups and extended profiles using the SremConfiguring groups using the Srem This section contains the following topics Click a Guide to Create a Group on the toolbar Using the guide for creating groups Groups screen 320818-A Adding a group Add a Group fields Click Add Add a Group dialog box appears see Figure Group Configuration screen appears see Figure To configure a group, perform the following stepsModifying a group Group Configuration fields Configuring client filters using the Srem Client Filters screen appears see Figure Adding a client filter Add a Client Filter fields Sheet 1 Click Add Add a Client Filter dialog box appears see Figure Check using the Srem on Client filter Configuration screen appears see Figure To configure a client filter, perform the following stepsModifying a client filter Client Filters configuration fields Configuring extended profiles using the Srem Extended Profiles screen appears see Figure Adding an extended profile Add an Extended Profile fields Add an Extended Profile screen Modifying an extended profile Extended profiles Configuration screen appears see Figure Extended Profile Configuration fields Mapping linksets to a group or profile using the Srem Linksets screen for a group Mapping linksets to a group To add a linkset to a group, perform the following steps Adding linksets to a groupAdd a Linkset fields Reordering linksets in a group Removing linksets from a group Linksets screen for an extended profile Mapping linksets to a profile Adding linksets to an extended profile Reordering linksets in an extended profile Removing linksets from an extended profile AAA Configuration screen 320818-A Creating a default group using the Srem AAA Configuration fields Configuring groups and profiles 320818-A Chapter Configuring authentication Configuring authentication Before you begin Configuring authentication using the CLI Cfg/domain 1/aaa Roadmap of authentication commands Command Cfg/domain 1/aaa/auth auth ID Configuring authentication methods using the CLI Radiusldaplocal Cfg/domain 1/aaa/auth auth ID followed byDisplay Local accesses the Local database menu Cfg/domain 1/aaa/auth #/adv Configuring Radius authentication using the CLICfg/domain 1/aaa/auth #/adv followed by Groupauth auth IDs You can perform the following configuration tasks Adding the Radius authentication method using the CLI Configuring authentication Main# /cfg/domain 1/aaa/auth Modifying Radius configuration settings using the CLICfg/domain 1/aaa/auth #/radius Type Cfg/domain 1/aaa/auth #/radius followed by Timeout interval Managing Radius authentication servers using the CLIRadius servers menu displays Sessiontim Cfg/domain 1/aaa/auth #/radius/servers followed by Radius servers menu includes the following options Configuring session timeout using the CLI Configuring Ldap authentication using the CLICfg/domain 1/aaa/auth #/radius/sessiontim Adding the Ldap authentication method using the CLI Configuring authentication Cfg/domain 1/aaa/auth #/ldap Modifying Ldap configuration settings using the CLI Cfg/domain 1/aaa/auth #/ldap followed by Ldap menu displays Ldap menu includes the following optionsDo not use the isdbinddn and isdbindpas Isdbindpas password SAMAccountName=bill . The user’s loginUserattr names Ou=Users, dc=example, dc=com . Enauserpre truefalse Enaldaps truefalseActivedire Cfg/domain 1/aaa/auth #/ldap/servers Managing Ldap authentication servers using the CLI Removes the specified Ldap server from the current Cfg/domain 1/aaa/auth #/ldap/ldapmacro Managing Ldap macros using the CLICfg/domain 1/aaa/auth #/ldap/ldapmacro followed by Ldap attribute Add variable namePrefix suffix Variable name Set the Active Directory settings using Managing Active Directory passwords using the CLIActive Directory Settings menu displays Cfg/domain 1/aaa/auth #/ldap/activedire command Configuring local database authentication using the CLI Configuring authentication Authentication menu commands local database You can add users to the database in two ways Managing the local database using the CLILocal database menu displays Cfg/domain 1/aaa/auth #/local Local database menu includes the following options Cur group commandCfg/domain 1/aaa/auth #/local followed by TAB or use the /cfg/domain 1/aaa Server filename key Import protocol Export protocol Specifying authentication fallback order using the CLI Main# /cfg/domain 1/aaa/authorder Cfg/domain 1/aaa/authorder auth ID,auth ID Configuring authentication using the Srem Authentication Server Table appears see Figure Configuring authentication methods using the Srem Configuring Radius authentication using the Srem Adding the Radius method and server Add an Authentication Server Radius 320818-A Add an Authentication Server Radius fields Modifying Radius configuration Configuration 320818-A Modifying Radius method settings Configuration fields Radius Configuration screen appears see Figure Modifying Radius configuration settings Radius Configuration fields Configuring authentication Radius Configuration fields Managing additional Radius servers Add a Radius Server fields Adding a Radius server Reordering additional Radius servers Configuring authentication Add a Radius Server fieldsRemoving a Radius server Next steps Configuring Ldap authentication using the Srem Adding the Ldap method and server Add an Authentication Server Ldap fields Modifying Ldap configuration Modifying Ldap method settings Configuration fields Ldap Configuration screen appears see Figure Modifying Ldap configuration settings Ldap Configuration fields Cn=Users, dc=example, dc=com Ou=Users, dc=example, dc=com. The user Active Directory, on Configuring authentication Ldap Configuration fields Managing additional Ldap servers Click Apply Adding an Ldap serverAdd an Ldap Server fields Removing an Ldap server Reordering additional Ldap servers Managing Ldap macros Ldap Macros Add an Ldap Macro fields Adding Ldap macros Removing Ldap macros Reordering Ldap macros Populate the database see Populating the database on Configuring local database authentication using the Srem Adding the Local method Database on Add an Authentication Server Local fields Adding users to the local database Populating the databaseYou can populate the Local database in two ways Local Users screen appears see Figure Add a Local User fields Click Add Add a Local User dialog box appears see Figure Configuring authentication Import Local User Database 320818-A Importing a database Import Local User Database fields Modifying Local database configuration Modifying Local method settings Local Users screen appears see on Modifying local users Local Users Configuration 320818-A Local Users Configuration fields Modifying local user passwords Local Users Local User Configuration 320818-A Select the Local User Configuration tab Local Users Local User Configuration fields Export Local User Database 320818-A Exporting the database Export Local User Database fields Specifying authentication fallback order using the Srem Authentication Server Order Saving authentication settings Chapter TunnelGuard SRS Builder TunnelGuard user interface Configuring SRS rulesTunnelGuard SRS Builder \tunnelguard\tg.txt File menu Menu commandsSoftware Definition menu Describes important items from the File menu Software Definition Entry menu items Sheet 1 Software Definition Entry menu Tool menu TunnelGuard Rule menuDescribes important items from the TunnelGuard Rule menu Describes important items from the Tool menu SRS Definition toolbar item descriptions SRS definition toolbar SRS Components table Software Definition Available SRS listSRS Components table items WINNT%\xxx.dll Customizing a component TunnelGuard Rule Definition screen Memory snapshotSRS Rule toolbar Memory snapshot item descriptions SRS Rule Expression Constructor SRS Rule listAvailable Expression list Rule Expression Constructor Creating a software definition Managing TunnelGuard rules and expressions Selecting modules or files from running processes Adding entries to a software definition Create New Memory Module SRS window For more information, see Making API calls on Select the TunnelGuard Rule Definition tab Selecting file on disk Create New on Disk SRS Entry window Creating logical expressions TunnelGuard Rule Definition tab Click the TunnelGuard Rule Definition tab Click the Form TunnelGuard Rule Expression button New SRS Rule window Available Expressions screen TunnelGuard Rule Name screen Registry-only SRS entry Registry-based rules Supported integer operands Describes supported operands for integer values String regular expression Description Constructs for string based regular expressions Sheet 1 Creating a registry entry Enter the Key Value Data Expression Registry-based File/ModuleTunnelGuard SRS Builder Registry Entry Manually creating an OnDisk file entry Manually creating SRS entries Create new OnDisk SRS Entry Create New Memory Module SRS Entry page opens see on Manually creating a Memory Module entry Create new Memory Module SRS entry File age check Adding a TunnelGuard rule comment Adding commentsTunnelGuard SRS Builder Date/Time Range Adding a software definition comment Deleting SRS rules and their components Deleting a software definition entry Deleting a software definitionDeleting a TunnelGuard rule Deleting an expression Making API calls TunnelGuard support for API calls TunnelGuard SRS Builder 320818-A Chapter Managing system users and groups Managing system users and groups User rights and group membershipGroup membership and user rights Roadmap of system user management commands Managing system users and groups using the CLICfg/sys/user User menu displays User menu includes the following options Managing user accounts and passwords using the CLICfg/sys/user followed by Add username Del username Edit username Managing user settings using the CLICaphrase Password user Managing user groups using the CLIPassword confirm User password Cfg/sys/user/edit username Adding a new user CLI configuration examplesThis section includes the following detailed examples Cfg/sys/user/edit username/groups Main# /cfg/sys/user Access the User Menu User# edit certadmin Apply the changes Verify and apply the changes Changing a user’s group assignment User# edit admin Changing your own password Changing passwords Changing another user’s password Type the password command to initialize the password change Deleting a user Managing user accounts using the Srem Managing system users and groups using the SremTo manage users, choose from one of the following tasks User Table Click Add Add a User dialog box appears see Figure Adding new user accounts To remove an existing user, perform the following steps Removing existing user accountsAdd a User fields Password Setting 320818-A Setting password expiry using the Srem Password Settings fields Change Your Password 320818-A Changing your password using the Srem Click Change Password Changing another user’s password using the SremOnly the admin user can change the passwords of other users Change Your Password fields Change User Password 320818-A Change User Password fields Setting the certificate export passphrase using the Srem Set Certificate Export PassPhrase 320818-A Set Certificate Export PassPhrase screen appears see Figure Click Set Pass Phrase Managing user groups using the SremSet Certificate Export PassPhrase fields Choose from the following tasks to manage users groups Adding a user groupTo add a new user group, perform the following steps Click Add Add a User Group dialog box appears see Figure Removing a user groupAdd a User Group fields Managing system users and groups Chapter Customizing the portal and user logon Customizing the portal and user logon Captive portal and Exclude List Exclude List String Usage Expressions Allowed regular expressions and escape sequences Portal look and feel Portal display Colors Default appearance Color Hexadecimal code Common colors, with hexadecimal codes Sheet 1 Language localization Content-Type text/plain charset=iso-8859-1/n Autorun linksets Linksets and links Macros Planning the linksets Examples of redirection URLs and links Automatic redirection to internal sitesExamples of redirection URLs and link text Sheet 1 Automatic JRE upload Managing the end user experience Roadmap of portal and logon configuration commands Customizing the portal and logon using the CLIWindows domain logon script Number Color2 code Configuring the Exclude List using the CLI Configuring the captive portal using the CLIDNS Exclude menu displays Cfg/domain 1/dnscapt DNS Exclude menu includes the following options Changing the portal language using the CLICfg/domain 1/dnscapt/exclude followed by Language Support menu displays Configuring language support using the CLICfg/lang Language Support menu includes the following options Cfg/lang/import commandCfg/lang followed by Server filename Cfg/domain 1/portal/lang Setting the portal display language using the CLICfg/domain 1/portal/lang followed by Cfg/domain 1/portal/lang/list Restore Configuring the portal display using the CLICfg/domain 1/portal Cfg/domain 1/portal followed by Redirect URL Logintext text Linkurl onoff Linktext textLinkcols columns Linkwidth width Portal Colors menu displays Changing the portal colors using the CLICfg/domain 1/portal/colors Portal Custom Content menu displays Configuring custom content using the CLICfg/domain 1/portal/content Portal Colors menu includes the following options Cfg/domain 1/portal/content followed by Portal Custom Content menu includes the following optionsTftpftpscpsftp. The default is tftp Available Cfg/domain 1/linkset linkset ID Configuring linksets using the CLI Cfg/domain 1/linkset linkset ID followed by Linkset menu includes the following optionsText text Autorun truefalse Cfg/domain 1/linkset linkset ID/link index Configuring links using the CLI Cfg/domain 1/linkset linkset ID/link index followed by Link menu includes the following optionsMove new index Configuring FTP link settings using the CLI Configuring external link settings using the CLICfg/domain 1/linkset linkset ID/link index/ external/quick Cfg/domain 1/linkset linkset ID/link index/ ftp/quick Configuring the captive portal using the Srem Customizing the portal and logon using the SremEnabling DNS capture DNS Capture fields DNS Capture screen includes the following components Click Add Entry appears in the DNS Exclude List Configuring the DNS Exclude List using the SremAdd DNS Domain fields Changing the portal language using the Srem Select the System Language tab Configuring language support using the SremLanguages sub-tabs appear see Figure Choose from one of the following tasks Viewing predefined languages To view custom languages, use the following procedureViewing and removing custom languages Click the Import/Export Definition tab Importing and exporting language definitionsImport/Export Definition screen appears see Figure Import/Export Definition fields Setting the portal display language using the Srem Language fields Configuring the portal display using the Srem Portal Configuration tab appears see Figure Configuring content Portal Configuration fields Sites, see on Import Banner screen 320818-A Importing banners Import Banner fields Color Settings screen 320818-A Changing the portal colors using the Srem Color Settings fields Configuring custom content using the Srem Basics screen appears see Figure Viewing basic information about custom content Basics fields To import custom content, perform the following steps Importing custom contentImport Content screen appears see Figure Import Content fields To export custom content, perform the following steps Exporting custom contentExport Content screen appears see Figure Export Content fields Configuring linksets using the Srem To create a linkset, perform the following steps Creating a linksetPortal Links screen appears see Figure Add a Linkset Click Add Add a Linkset dialog box appears see Figure Modifying a linkset Linkset Configuration screen appears see FigureTo modify a linkset, perform the following steps See Linksets and links on Linkset Configuration fields Configuring links using the Srem To create an external link, perform the following steps Creating an external link using the SremLinks screen appears see Figure Add a Portal Link fields Click Add Add a Portal Link dialog box appears see Figure Creating an FTP link using the Srem Add a Portal Link FTP To create an FTP link, perform the following steps Add a Portal Link FTP fields External link Configuration screen appears see Figure Modifying external link settings using the SremTo modify a link, perform the following steps Reordering links using the Srem on External link Configuration fields FTP link Configuration screen appears see Figure Modifying FTP link settings using the Srem FTP link Configuration fields Reordering links using the Srem Re Order Links fields Re Order Links screen appears see Figure Customizing the portal and user logon 320818-A Chapter Configuring system settings Configuring system settings Cfg/sys Configuring the cluster using the CLI Roadmap of system commands Parameter Health interval Show Cfg/sys followed by Configuring system settings using the CLIRsa server ID Cfg/domain #/server/trace/ssldump Configuring the Nortel Snas 4050 host using the CLICfg/domain #/server/trace/tcpdump Cfg/sys/host host ID Cfg/sys/host host ID followed by Cluster Host menu includes the following options/cfg/sys/host #/interface # Interface number Ports = 1,23 PortsHwplatform Halt Cfg/sys/cur command RebootCfg/sys/host #/delete Viewing host information Configuring host interfaces using the CLICfg/sys/host host ID/interface interface ID Cfg/sys/host #/interface interface ID Vlanid tag Cfg/sys/host #/interface interface ID followed byMode Failovertrunking Primary port Configuring static routes using the CLICfg/sys/routes Cfg/sys/host host ID/routes Cfg/sys/host #/interface #/routes followed by Configuring host ports using the CLIAdd IPaddr mask Gateway Host Port menu includes the following options Managing interface ports using the CLICfg/sys/host #/port port followed by Cfg/sys/host #/interface interface ID/ports Cfg/sys/host #/ports command see Configuring the Access List using the CLICfg/sys/accesslist Interface Ports menu includes the following options Cfg/sys/accesslist followed by Configuring date and time settings using the CLIDate and Time menu displays Add IPaddr mask Date and Time menu includes the following options Managing NTP serversNTP Servers menu displays Cfg/sys/time followed by NTP Servers menu includes the following options Configuring DNS servers and settings using the CLICfg/sys/time/ntp followed by Cfg/sys/dns Count count Retransmit intervalTtl ttl Health interval Cfg/sys/dns/servers Managing DNS serversCfg/sys/dns/servers followed by RSA Servers menu displays Switch Software Release Configuring RSA servers using the CLIMove index number new index number Cfg/sys/rsa RSA Servers menu includes the following options Configuring syslog servers using the CLISyslog Servers menu displays Cfg/sys/rsa followed by Cfg/sys/syslog followed by Syslog Servers menu includes the following optionsFacility Syslog.conf under Unix Administrative Applications menu displays Configuring administrative settings using the CLICfg/sys/adm Cfg/sys/adm followed by Audit SrsadminAuth Telnet onoff Configuring Nortel Snas 4050 host SSH keys using the CLI Enabling TunnelGuard SRS administration using the CLICfg/sys/adm/srsadmin Cfg/sys/adm/srsadmin followed by Cfg/sys/adm/sshkeys followed by Cfg/sys/adm/sshkeysDraft-ietf-secsh-publickeyfile Knownhosts SSH Known Host Keys menu displays Managing known hosts SSH keys using the CLISSH Known Host Keys menu includes the following options Cfg/sys/adm/sshkeys/knownhosts About Radius auditing Configuring Radius auditing using the CLIAbout the vendor-specific attributes Map this string to the Vendor-Type value Configuring Radius auditingNSNAS-SSL-Audit-Trail Cfg/sys/adm/audit Radius Audit Servers menu displays Managing Radius audit servers using the CLIRadius Audit Servers menu includes the following options Cfg/sys/adm/audit/servers Adds a Radius audit server to the configuration. You Cfg/sys/adm/auth Configuring authentication of system users using the CLI Fallback onoff Radius Authentication Servers menu displaysCfg/sys/adm/auth/servers Cfg/sys/adm/auth/servers followed by Configuring the cluster using the Srem Select the System Configuration tab Configuring system settings using the SremSystem Configuration screen appears see Figure System Configuration fields Configuring a Nortel Snas 4050 host using the Srem Hosts Host Viewing and configuring TCP/IP properties Host fields Viewing and installing host licenses Viewing global licenses for all hosts Global Licenses fields Describes the Global Licenses fields Viewing per domain licenses for all hosts Per Domain Licenses fields Describes the Per Domain Licenses fields Viewing installed licenses for a particular host Installing a license for a particular host Install New License To continue, choose one of the following procedures Configuring host interfaces using the Srem To create a host interface, perform the following steps Adding a host interfaceSelect the System Hosts host Interfaces tab Add an Interface fields Click Apply New interface appears in the Interfaces table Configuring system settings Add an Interface fields Configuring an existing host interface Interface fields Link is transferred back to the primary port Removing a host interface Configuring static routes using the SremTo delete a host interface, perform the following steps IP Routes Viewing static routes for a cluster Routes Viewing static routes for a host Managing static routes Viewing static routes for an interface Add Route fields Adding a static route Removing a static route Ports Configuring host ports using the Srem Port Port fields Managing interface ports using the Srem Removing interface ports Adding interface portsAdd a Port fields Configuring the access list using the Srem Access List Table appears see Figure Adding an access list entrySelect the System Access List tab Access List Table appears see on Click Add Add Access Host dialog box appears see Figure Removing an Access List entryAdd Access Host fields Date & Time Managing date and time settings using the Srem Select the System Date & Time tab Configuring the date and time settingsDate & Time fields Select the System Date and Time tab Adding an NTP serverAdd NTP Server fields Removing an NTP server Select the System DNS Client Settings tab Configuring DNS settings using the SremDNS Client Settings screen appears see Figure DNS Client Settings fields Managing syslog servers Configuring servers using the Srem From this screen, complete the following tasks as necessary Adding a new syslog serverClick Add Add Syslog Server dialog box appears see Figure Add Syslog Server fields Removing an existing syslog server Reordering a new syslog server Adding a DNS server on Removing an existing DNS server on Select the System Servers DNS Servers tab Adding a DNS serverAdd DNS Server fields Removing an existing DNS server RSA Server Table Managing RSA servers Adding an RSA server To configure RSA servers, perform the following stepsSelect the System Servers RSA Server Table tab Add RSA Server fields Removing the RSA node secret Removing an existing RSA server RSA Server fields Describes the RSA Server fields Click Remove Secret Node Importing sdconf.recSelect an RSA server from the RSA Server Table Import sdconf.rec screen appears see Figure Select the Import sdconf.rec tab Import sdconf.rec fields Configuring administrative settings using the Srem Configuring SRS control settings using the Srem Select from one of the following tasks Configuring Nortel Snas 4050 host SSH keys usingAdd SSH Key fields Show SSH Keys Showing SSH keys Configuring system settings Managing Nortel Snas 4050 and known host SSH keys SSH Keys Hosts field Click Generate SSH Keys Add SSH Key Adding an SSH key for a known host using the Srem Managing Radius audit settings using the Srem About the vendor-specific attributes Configuring Radius auditing Radius audit Configuration Configuring Radius audit settings using the Srem Add Audit Configuration fields Describes the Add Audit Configuration fields Select from the following tasks to manage the audit servers Managing Radius audit servers using the Srem Click Add Add Audit Server dialog box appears see Figure Adding a new Audit ServerAdd Audit Server fields Removing an existing Radius audit server Managing Radius authentication of system users using Configuring Radius authentication of system users using Radius Authentication Configuration fields Radius Server Table appears see Figure Managing Radius authentication servers using the Srem Add Radius Server fields Adding a Radius authentication server Removing an existing Radius server Configuring system settings 320818-A Chapter Managing certificates Managing certificates Supported key and certificate formats Sheet 1 Key and certificate formats 320818-A Creating certificates Installing certificates and keys Updating certificates Saving or exporting certificates and keys Managing private keys and certificates using the CLI Roadmap of certificate management commands Cfg/cert cert id Managing and viewing certificates and keys using the CLICfg/cert cert ID followed by /cfg/cert #/show command Cert #/export command Generating and submitting a CSR using the CLIPhrase CSR information Cfg/cert #/request Emailemail-address IPip-address Generating a CSR Email Address tester@dummyssltesting.com Save the CSR to a file Adding a certificate to the Nortel Snas 4050 using the CLI Add the certificate Enter the following command Entire contents of the key, includingLines Cfg/cert #/cert Certificate added Certificate 2# apply Adding a certificate by pasting Add the private key Enter the following command Adding a private key to the Nortel Snas 4050 using the CLICfg/cert #/key Adding a private key by pasting Certificate and key import information Cfg/cert #/import Anonymous Admin@hostname.isd Cfg/cert #/display Displaying or saving a certificate and key using the CLI Copy the private key, certificate, or both, as required Displaying a private key and certificate Certificate and key export information Cfg/cert #/export About the formats, see Key and certificate formats on Cfg/cert #/test Generating a test certificate using the CLI Managing private keys and certificates using the Srem Certificates screen Viewing certificates using the Srem To create a certificate, perform the following steps Creating a certificate using the SremSelect the Certificates Certificates tab Add a Certificate Component fields Managing certificates To generate a CSR, perform the following steps Generating and submitting a CSR using the Srem CA Request fields Importing a certificate or key using the Srem Import Certificate screen 320818-A Import Certificate fields Displaying or saving a certificate and key using the Srem Display Certificate screen 320818-A Display Certificates fields Export Certificate screen 320818-A Export Certificate fields Viewing configuration details Viewing certificate information using the Srem Describes the certificate Configuration fields Configuration screen appears see FigureCertificate Configuration fields Viewing general information Managing certificates Certificate Configuration fields Describes the Info fields Info screen appears see FigureInfo fields Managing certificates Info fields Viewing certificate subject settings Describes the Subject fields Subject screen appears see FigureSubject fields Managing certificates Subject fields Chapter Configuring Snmp Configuring Snmp Configuring Snmp using the CLICfg/sys/adm/snmp Roadmap of Snmp commands Snmp menu displays Snmp menu includes the following options Configuring Snmp settings using the CLI SNMPv2-MIBmenu displays Configuring the Snmp v2 MIB using the CLICfg/sys/adm/snmp/snmpv2-mib SNMPv2-MIBmenu includes the following options Configuring the Snmp community using the CLICfg/sys/adm/snmp/snmpv2-mib followed by Cfg/sys/adm/snmp/community Cfg/sys/adm/snmp/users user ID Configuring SNMPv3 users using the CLI Des Aes Md5 Sha Cfg/sys/adm/snmp/users user ID followed by Snmp User menu includes the following options Notification Target menu displays Configuring Snmp notification targets using the CLICfg/sys/adm/snmp/target target ID Notification Target menu includes the following options Configuring Snmp events using the CLIEvent menu displays Version v1v2cv3 Cfg/sys/adm/snmp/event followed by Event menu includes the following optionsOptions -b name OID op value OID value Options -t nameEvent OID Options -x nameComment name Notification This section contains information about the following topics Configuring Snmp settings using the Srem To configure SNMP, perform the following steps Configuring Snmp using the Srem Sonmp Snmp Configuration fields Configuring Snmp targets using the Srem To add an Snmp target, perform the following steps Adding Snmp targetsSnmp Target Table appears see Figure Add Snmp Target 320818-A Click Add Add Snmp Target dialog box appears see Figure Snmp Target fields Managing Snmp targets Target Settings screen appears see FigureTo manage Snmp targets, perform the following steps Removing Snmp targets Configuring SNMPv3 users using the Srem To add an SNMPv3 user, perform the following steps Adding SNMPv3 usersSNMPv3 User Table appears see Figure Add SNMPv3 User 320818-A Click Add Add SNMPv3 User dialog box appears see Figure Add SNMPv3 User fields Managing SNMPv3 users User Settings screen appears see Figure User Settings fields Sheet 1 Removing SNMPv3 users Configuring Snmp User Settings fields Sheet 2 Managing monitor events Configuring Snmp events using the SremTo manage monitor events, select from the following tasks To add monitor events, perform the following steps Adding monitor events Add a Monitor fields Viewing configuration details of monitor events Boolean monitors Removing monitor eventsTo delete a monitor event, perform the following steps Boolean monitor fields Sheet 1 Add a Monitor Boolean Threshold monitors Configuring Snmp Boolean monitor fields Sheet 2 Threshold monitor fields Existence monitor fields Sheet 1 Existence monitors Existence monitor fields Sheet 2 Managing notification events To add notification events, perform the following steps Adding notification eventsNotification Table screen appears see Figure Add a Notification Event fields Add a Notification Event To delete a notification event, perform the following steps Removing notification events 659 Viewing system information and performance statistics Roadmap of information and statistics commandsInfo Stats Information menu displays Viewing system information using the CLI Info followed by Information menu includes the following optionsDomain ID Info/mac command SwitchidKick domain ID Username Switch ID Info/ip commandMac MACaddr Username-prefix Ethernet Local To view active alarms, use the following command Viewing alarm events using the CLIInfo/events Info/events followed by Viewing AAA statistics using the CLI Viewing log files using the CLITo view and download log files, use the following command Logs menu displays Logs menu includes the following options Stats/aaa followed by Stats/aaaTotal Isdhost host ID Main# stats/aaa/dump Viewing local information using the Srem Viewing all statistics using the CLIStats/dump Describes the Information fields Information screen appears see FigureInformation fields Viewing cluster information using the Srem Viewing the controller list using the Srem Controller List fields Describes the Controller List fields Viewing Sonmp topology information using the Srem Sonmp State fields Describes the Sonmp State fields Viewing switch distribution using the Srem Describes the Switch Distribution fields Viewing port information using the SremSwitch Distribution fields Port Information fields Sheet 1 Describes the Port Information fields Viewing license information using the Srem Viewing global license information Nortel Snas 4050, SSL is the only type of license Viewing license information for a domain Viewing session details using the Srem Sessions screen Viewing active sessions using the Srem Sessions parameters Describes the Sessions parameters Session Properties screen Viewing details for a particular session Describes the Session Properties parameters Ending active user sessions KickOut User fields Click KickOut Describes the Number of Sessions fields Viewing the number of active sessions using the SremNumber of Sessions fields Viewing alarms using the Srem Active Alarms screen 320818-A Viewing active alarms using the Srem Active Alarms fields Describes the Active Alarms fields Download Alarms screen 320818-A Downloading alarms using the Srem Describes the Download Alarms fields Managing log files using the SremDownload Alarms fields Logs screen Viewing the log list using the Srem Describes the Download fields Downloading log files using the SremDownload fields Sheet 1 Viewing AAA statistics using the Srem Hosts table Viewing AAA statistics for a host License tab opens see on For a description of the fields, seeTable Viewing License statisticsLicense statistics Sheet 1 Radius statistics 320818-A Viewing Radius statistics Radius statistics Local DB statistics Sheet 1 Viewing Local database statistics Viewing Ldap statistics Ldap statistics Statistics table Viewing AAA statistics for the domain Select one of the following tasks Viewing License statistics For the Nortel Snas 4050, SSL is the only type of license Viewing Radius Statistics Sheet 1 For a description of the fields, see Table 320818-A Viewing Local database statistics Logging Accepted Rejected Viewing Ldap Statistics Sheet 1 Viewing Ethernet statistics using the Srem Ethernet Interface table For a description of the fields seeTable Viewing Rx statisticsViewing Rx statistics Sheet 1 Rx Frames Displays number of errors due to malformed packets Viewing Tx Statistics Sheet 1 Viewing Tx statistics Information, see Configuring host ports using the Srem Page Chapter Maintaining and managing the system Maintaining and managing the system Managing and maintaining the system using the CLIMaint Boot Roadmap of maintenance and boot commands Maintenance menu displays Performing maintenance using the CLI Dumplogs protocol server filename all-isds? Maintenance menu includes the following options All-isds? Maint followed by Domain ID output Starttrace tagsMode Stoptrace Cfg/dump passphrase Backing up or restoring the configuration using the CLI Cfg Configuration menu backup and restore commandsPtcfg protocol Server filename passphrase Gtcfg protocol Cfg followed byPassphrase Dump passphrase Boot menu displays Boot menu includes the following options Managing Nortel Snas 4050 devices using the CLIBoot followed by Software Cfg/sys/host #/delete command see Cfg/sys/host #/reboot command insteadCfg/sys/host #/delete command Boot/software Activate command Boot/software followed bySoftware Management menu includes the following options Activate version Performing maintenance using the Srem Managing and maintaining the system using the SremUpgradecomplete.pkg Ftp 10.0.0.1 pub/SSL-5.1.1 Dumps Dumping logs and status information using the Srem Click Dump Starting and stopping a trace using the SremDump fields To start or stop a trace, perform the following steps Start/Stop Trace fields Click Check Configuration Checking configuration using the Srem Backup & Restore 320818-A Backing up or restoring the configuration using the Srem If you later restore the configuration, the Certificate Backup & Restore fields Image List Managing software versions using the Srem Following tasks are available from this screen Describes the Image List fieldsImage List fields Viewing details of the active software image Select the System Boot Image List tab Activating a software image Removing an inactive software image Downloading images using the Srem Maintaining and managing the system Download Image fields Rebooting or deleting a Nortel Snas 4050 device using Reboot/Delete ISD Options Downloading files using the Srem Describes the File Download fields File Download screen appears see FigureFile Download fields Maintaining and managing the system File Download fields Running Nortel Snas 4050 diagnostics using the Srem Diagnostics fields Describes the Diagnostics fields Maintaining and managing the system 320818-A Upgrading the Nortel Snas Chapter Upgrading or reinstalling the software Upgrading or reinstalling the software Performing minor and major release upgrades Enter the host name or IP address of the server Downloading the software image using the CLI Admin@hostname/IP.isd Activating the software upgrade package Nsnas Log in again and verify the new software version At the Software Management# prompt, enter Before you begin Reinstalling the software Upgrading or reinstalling the software Reinstalling the software from an external file server Restarting Restarting system Booting LoginAlteon WebSystems, Inc When the installation is complete, remove the CD and reboot Reinstalling the software from a CDRun install-nsnas isd4050 Upgrading or reinstalling the software 320818-A Chapter Command Line Interface Command Line Interface Connecting to the Nortel SnasEstablishing a console connection Console configuration parameters ProcedureRequirements Establishing a Telnet connection Enabling and restricting Telnet access Enabling and restricting SSH access Establishing a connection using SSHRunning Telnet Running an SSH client For more information, see How to get help on Accessing the Nortel Snas 4050 cluster User access levels Command line history and editing CLI Main Menu or SetupIdle timeout Command Line Interface Scenario On page 780 illustrates the network configuration Network devices Sheet 1 Configuration example Configuration example Network devices Sheet 2 Summarizes the VLANs for the Ethernet Routing SwitchVLANs for the Ethernet Routing Switch Steps Configure the network DNS server Create a new Dhcp scope see Figure Configure the network Dhcp server Naming the new Dhcp scope 320818-A Specify the IP address range for the Dhcp scope see Figure Choosing to configure additional options 320818-A Enter the IP address of the default gateway see Figure Specifying the DNS server Enter the IP address of the DNS server see Figure Shows the Dhcp scopes created for use in this example Configure the network core router Steps Configure the Ethernet Routing Switch 8300 using the CLI Configuring the VoIP VLANs Configuring the Nortel Snas 4050 pVIP subnetConfiguring the Red, Yellow, and Green VLANs Enabling SSH Configuring the Nsna ports Configuring the Nsna uplink filterEnabling Nsna globally Add the uplink port Setting the switch IP address Configure the Ethernet Routing Switch 5510-48Tconfig# ssh Configuring SSH5510-48Tconfig#nsna nsnas 10.40.40.0/24 5510-48Tconfig#nsna vlan 240 color voip Configuring the login domain controller filters Configure the Nortel Snas5510-48Tconfig-if#exit 5510-48Tconfig#nsna enable 10.40.40.1 Performing initial setup Enable SRS administration Completing initial setupEnter a password for the admin user Main# cfg/sys/adm/srsadmin/ena Main# cfg/domain 1/sshkey/generate Adding the network access devicesGroup 1# /cfg/domain 1/aaa/tg/quick TG#../group 1/tgsrs srs-rule-test Add the switch manually Adding the Ethernet Routing SwitchImport the public SSH key from the switch Main# cfg/domain 1/switch 1 Creating Switch Main# cfg/domain 1/switch 2/sshkey/import Use the quick switch wizardMain# cfg/domain 1/switch 1/vlan/add yellow Switch Vlan# ../../vlan/add yellow Main# cfg/domain 1/switch 1/ena Switch 1# ../switch 2/ena Enabling the network access devicesSwitch 2# apply Changes applied successfully Domain Vlan# apply Changes applied successfully Configuration example 320818-A Appendix a CLI reference Global commands Using the CLI Exit PasteQuit Netstat Command line history and editing You can use the following CLI command shortcuts Command stackingCommand line history and editing options Sheet 2 CLI shortcuts Tab completion Command abbreviationNTP Servers# ../../dns/servers Main# cfg/sys/time/ntp/list Main# c/sy/t/n/l Configuration# cur sys Using a submenu name as a command argument IP address and network mask formats Using slashes and spaces in commandsIP addresses Network masks Variables Variables CLI Main Menu CLI command reference Appendix a CLI reference Information menu Information menu commands Sheet 1Certs Sys Statistics menu Configuration menu commands Sheet 1 Configuration menuCfg/cert cert ID Name name Cert Auth ID Radiusldaplocal Cfg/domain Name nameAuth #/adv Secondauth auth ID Auth ID for Ldap Auth #/ldap Searchbase Cfg/domain #/aaa ServersAuth #/ldap/activedire Truefalse Expiredgro Group Cfg/domain #/aaa Add user name Auth #/local Password groupPasswd user name Auth #/radius Vendorid vendor ID Cfg/domain #/aaa Vendorid vendor ID Profile ID Access rule Number Linkset DelAuth #/radius Vendortype vendor Type Ena Dis Cfg/domain #/aaa Group #/linkset Del index number Group #/extend # Del index numberRadacct Vpnattribu Ena Dis Cfg/domain #/aaa List Recheck interval Cfg/domain #/aaa/tg QuickHeartbeat interval Cfg/domain #/adv Interface interface Cfg/domain #/linkset Name name RestoreLinkset ID Text text Linkset #/link index Text text Cfg/domain #/portal Color1 code Content Server filenameColors Color2 code Lang Charset Adv/traflog Udpport port Cfg/domain #/server Sysloghost IPaddrProtocol Ssl2ssl3ssl23tls1 Switch ID Type ERS8300ERS5500 Cfg/domain #/switch Name nameSwitch #/dis Switch #/ena Passphrase Cfg/domain #/vlan Add name Vlan IDCfg/gtcfg protocol Passphrase Cfg/lang Import protocol Add IPaddr mask Cfg/sys/accesslist ListCfg/sys/adm Snmp Sonmp onoff Shared secret Cfg/sys/adm/auth ListCfg/sys/adm/snmp Ena Versions v1v2cv3 Disabledenabled Cfg/sys/adm/snmp Ip IPaddr Snmpv2-mib SnmpEnableCfg/sys/adm/snmp Addmonitor Event Options -b name Users user ID Seclevel Cfg/sys/adm/snmp Name nameDis Cfg/sys/adm/sshkeys Generate Knownhosts Cfg/sys/dns/servers List Mode fullhalf Cfg/sys/host #/routesInterface #/ports Del port Add port Cfg/sys/host # List Host ID SysName name Cfg/sys/host Ip IPaddrSysLocatio Cfg/sys/rsa Rsaname name Password new Add IPaddr Cfg/sys/user Password oldPassword confirm Username Password user Boot menu commands Boot menuBoot Software Reboot Delete Boot/software Cur Maintenance menu commands Maintenance menuMaint Dumplogs protocol All-isds? Troubleshooting tips Chapter Troubleshooting Verify the current configuration Cannot connect to the Nortel Snas 4050 using Telnet orEnable Telnet or SSH access Check the Access List Check the IP address configuration # /cfg/cur sys Cannot contact the MIP Cannot add the Nortel Snas 4050 to a cluster Main# /cfg/sys/accesslist/add Add Interface 1 IP addresses and the MIP to the Access ListEnter network address IP address Enter netmask network mask Telnet or SSH connection to the MIP Nortel Snas 4050 stops respondingConsole connection Administrator user password User password is lostOperator user password Root user password Trace tools Boot user passwordUser fails to connect to the Nortel Snas 4050 domain Main# maint/starttrace Tag Description Sample output Sample output for the trace command Installed certificates System diagnosticsNetwork diagnostics Main# /cfg/sys/cur Cluster Host 1# curMain# /stats/dump Main# /info/ethernet Error log files Active alarms and the events log file Troubleshooting Syslog messages by message type Appendix B Syslog messages Lists the Emerg operating system messages Operating system OS messagesLists the operating system Critical messages System Control Process messages Operating system messages ErrorLists the operating system Emerg messages Alarm severity and syslog level correspondence About alarm messagesLists the System Control Process Info messages System control process messages Info Alarm System Control Process messages Alarm About event messages Audit/ena commandSystem Control Process messages Event With /cfg/sys/cur Traffic Processing messages Error Sheet 1 Lists the Traffic Processing Error messagesTraffic Processing Subsystem messages Lists the Traffic Processing Critical messages Css error reason Lists the Traffic Processing Warning messages Traffic Processing messages Error Sheet 3Traffic Processing messages Warning Domain #/server/portal Lists the Traffic Processing Info messages Start-up messagesTraffic Processing messages Info AAA messages Error Lists the AAA Error messagesAAA subsystem messages Lists the Start-up Info messages Log value Message Category Contains AAA messages Info Sheet 1 There are two categories of Nsnas subsystem messages Nsnas subsystem messagesAAA messages Info Sheet 2 Nsnas Error Lists the Nsnas Error messagesLists the Nsnas Info messages Nsnas Info Sheet 1 Lists the syslog messages in alphabetical order Syslog messages in alphabetical orderNsnas Info Sheet 2 Syslog messages in alphabetical order Sheet 1 Sys/adm/audit/ena command Syslog messages in alphabetical order Sheet 3 Error Nsnas Info AAA Syslog messages in alphabetical order Sheet 5 Error AAA Cfg/domain #/server/portal Authenticate is set to off Syslog messages in alphabetical order Sheet 7 Root filesystem repaired Syslog messages in alphabetical order Sheet 9 Unable to use the certificate for Following MIBs are supported by the Nortel Snas Supported MIBs SNMPv2-MIB ANAifType-MIBAppendix C Supported MIBs Supported MIBs Sheet 1 ALTEON-ISD-SSL-MIB Supported MIBs Sheet 2 Appendix C Supported MIBs Supported MIBs Sheet 3 CLI, using the /cfg/sys/adm/snmp/target command Supported traps Use the CLI command /cfg/sys/adm/snmp/snmpv2-mibDescribes the traps supported by the Nortel Snas Supported traps Appendix C Supported MIBs 320818-A Supported ciphers Appendix D Supported ciphers Appendix D Supported ciphers Register the Schema Management dll Windows Server Install All Administrative Tools Windows 2000 Server Click Start and select Run Nortel Secure Network Access Switch 4050 User Guide Create a shortcut to the console window Permit write operations to the schema Windows 2000 ServerSelect a Title for the Program page displays Nortel Secure Network Access Switch 4050 User Guide Add isdUserPrefs attribute to nortelSSLOffload class Create the new class Add the nortelSSLOffload Class to the User Class 320818-A Appendix F Configuring Dhcp to auto-configure IP Phones Appendix F Configuring Dhcp to auto-configure IP Phones Configuring IP Phone auto-configurationCreating the Dhcp options Dhcp Management Console Click Add Option Type dialog box opens see on Predefined Options and Values dialog box opens see Figure Option Type dialog box Option Type dialog box field values for Vlan Information Scope Options dialog box Scope Options dialog box displays see Figure Call Server Information string parameter values Vlan ID Information string parameter values Setting up the IP PhonePage Create the logon script see Creating a logon script on Configuring the logon script Creating a logon script Using Windows, open a plain text editor, such as NotepadCreating the script as a batch file Creating the script as a VBScript file Assigning the logon script Right-click the Default Domain Policy and select Edit Double-clickDefault Domain PolicyOn the Group Policy tab, click Open Appendix H Software licensing information Appendix H Software licensing information GNU General Public License Appendix H Software licensing information Appendix H Software licensing information Apache Software License, Version Bouncy Castle license Index Symbols Index Index DNS Index Local authentication database Add users Cannot contact Index See also SRS rule SSL Index Index