Command Job Aid

Table A-10. Vectoring Commands — Generic 3 Version 4 (continued)

goto step1 ____ if

expected-wait

skill

_____

pri __

______

______

(1-32)

for5

 

(1-24 [G3vs/s])

(low, med,

(<, <=)

(1-9999)

 

 

 

(1-99 [G3i])

high, top)

(<, <=, <>, =)

(0-9999)

 

 

 

(1-255 [G3r])

 

 

 

 

 

 

 

 

 

 

expected-wait2call

_____

_____

 

 

 

for

 

(<, <=)3

(1-9999)

 

 

 

 

 

(>, >=, <>, =)

(0-9999)

 

 

 

ii-digits4

_____

table

_____

 

 

 

 

(in, not-in)

 

(1-5 [G3vs/s])

 

 

 

 

 

 

(1-10 [G3i])

 

 

 

 

 

 

(1-100 [G3r])

 

 

 

 

 

 

 

 

 

 

ii-digits4

_____

_____

 

 

 

 

 

(<, >, <=, >=)

(00-99)

 

 

 

 

 

(<>, =)

[00-99, +, +?, ?+, ??, ?x (where x = 0-9), x?, none]5

 

 

oldest-call-wait ______

pri __

_____

_____

 

 

in skill

(1-24 [G3vs/s])

(low, med,

(<, <=)

(2-998)6

 

 

 

1-99 [G3i])

high, top)

(>, >=, <>, =)

(0-998)6

 

 

 

(1-255 [G3r])

 

 

 

 

 

 

 

 

 

 

 

 

staffed-agents

_____

_____

_____

 

 

 

in skill

(1-24 [G3vs/s])

(<, <=)

(1-150 [G3vs/s], 1-200 [G3i],, 1-999 [G3r])

 

 

(1-99 [G3i])

(>, >=, <>, =)

(0-149 [G3vs/s],0-199 [G3i], 0-998 [G3r])

 

 

1-255 [G3r])

 

 

 

 

 

time-of-day is

_____

_____ to

_____

_____

 

 

 

(mon, tue,

(hh:mm in

(mon, tue,

(hh:mm in military

 

 

wed, thu, fri,

military time)

wed, thu, fri,

time)

 

 

 

sat, sun, all)

 

sat, sun, all)

 

 

unconditionally7

1.The “goto vector” command is identical to the “goto step” command, except the word step is replaced by the word vector. The valid values for vector are: 1-48 [G3vs/s], 1-256 [G3i], 1-512 {G3r].

2.The Vectoring (G3V4 Advanced Routing) and Vectoring (G3V4 Enhanced) options must be enabled.

3.The <=, >=, <>, and = comparators are new for G3V4. < = means less than or equal to, >= means greater than or equal to, <> means not equal to, and = means equal to.

4.The Vectoring (ANI/II-Digits Routing) and Vectoring (G3V4 Enhanced) options must be enabled.

5.A ? matches any digit 0-9 in that single digit position. A + matches any or no characters.

6.Even numbers only.

7.This command is also available with Call Prompting.

Issue 4 September 1994 A-13

Page 220
Image 220
AT&T 555-230-520 manual Table A-10. Vectoring Commands Generic 3 Version