NetWare Installation Checklists

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Task

 

With Access Logix

Without Access Logix

Reference Document

 

 

 

 

 

 

 

 

 

 

9

Storage System

On the server, restart the

N/A

CX-Series Server

 

 

 

Register HBAs

 

Navisphere Host Agent or run the

 

 

Software for NetWare

 

 

 

 

Navisphere Server Utility.

 

 

Installation Guide

 

 

 

 

 

 

 

 

 

 

 

Checkpoint - Use Navisphere

 

 

Navisphere Manager

 

 

 

 

 

Manager’s Connectivity Status

 

 

administrator’s guide

 

 

 

 

 

dialog box to verify that each HBA

 

 

and online help

 

 

 

 

 

is registered with the storage

 

 

 

 

 

 

 

 

system.

 

 

 

 

 

 

 

 

 

 

 

 

 

10

Storage System

For a CX200, CX300, CX400, CX500,

For a CX200, CX300, CX400, CX500,

Navisphere Manager

 

 

 

Set Properties

CX600, CX700, or FC4700-Series

CX600, CX700, or FC4700-Series

administrator’s guide

 

 

 

storage system

storage system

and online help or

 

 

 

for PowerPath

 

 

 

 

 

 

 

Navisphere CLI

 

 

 

 

Use Navisphere Manager’s

Use the following Navisphere CLI

 

 

 

 

 

Failover Setup Wizard (selected

command to determine the

reference

 

 

 

 

 

 

 

 

 

 

 

from the Tools menu on the

default storage-system type:

 

 

 

 

 

 

toolbar) to set the following

navicli -h hostname systemtype

 

 

 

 

 

 

storage-system properties for the

 

 

 

 

 

 

where hostname is the IP

 

 

 

 

 

 

server’s HBA ports (initiators):

 

 

 

 

 

 

Initiator Type to CLARiiON Open

address or network name of an

 

 

 

 

 

 

SP in the storage system.

 

 

 

 

 

 

Failover mode to 1

 

 

 

 

 

 

If the default storage-system

 

 

 

 

 

 

Array commpath to Enabled

 

 

 

 

 

 

system type is not 3 (CLARiiON

 

 

 

 

 

 

Unit Serial Number to LUN

Open), use the following

 

 

 

 

 

 

Navisphere CLI command to set

 

 

 

 

 

 

 

 

 

 

 

 

 

 

it to 3:

 

 

 

 

 

 

 

navicli -h hostname systemtype

 

 

 

 

 

 

 

-config 3

 

 

 

 

 

 

 

CAUTION The above command

 

 

 

 

 

 

 

reboots both SPs at the same

 

 

 

 

 

 

 

time.

 

 

 

 

 

 

 

Use the following Navisphere CLI

 

 

 

 

 

 

 

commands to set the default

 

 

 

 

 

 

 

failover mode and array

 

 

 

 

 

 

 

commpath properties to the

 

 

 

 

 

 

 

values for PowerPath:

 

 

 

 

 

 

 

navicli -h hostname

 

 

 

 

 

 

 

failovermode 1

 

 

 

 

 

 

 

navicli -h hostname

 

 

 

 

 

 

 

arraycommpath 1

 

 

 

 

 

 

 

where hostname is the IP

 

 

 

 

 

 

 

address or network name of an

 

 

 

 

 

 

 

SP in the storage system.

 

 

 

 

 

 

 

 

 

 

 

PowerPath Checklist — New NetWare Server and Existing Storage System

4-15

Page 173
Image 173
EMC 69001166 manual Unit Serial Number to LUN