Motorola DSP56301 Receiver Wakeup Enable, Wakeup Mode Select, Send Break, SCI Shift Direction

SCI Programming Model

Table 8-2.SCI Control Register (SCR) Bit Definitions (Continued)

Bit	Bit Name	Reset	Description
Number		Value
6	RWU	0	Receiver Wakeup Enable
			When RWU is set and the SCI is in Asynchronous mode, the wakeup function is
			enabled; i. e., the SCI is asleep and can be awakened by the event defined by the
			WAKE bit. In Sleep state, all interrupts and all receive flags except IDLE are disabled.
			When the receiver wakes up, RWU is cleared by the wakeup hardware. You can also
			clear the RWU bit to wake up the receiver. You can use RWU to ignore messages that
			are for other devices on a multidrop serial network. Wakeup on idle line (i. e., WAKE is
			cleared) or wakeup on address bit (i. e., WAKE is set) must be chosen. When WAKE is
			cleared and RWU is set, the receiver does not respond to data on the data line until an
			idle line is detected. When WAKE is set and RWU is set, the receiver does not respond
			to data on the data line until a data frame with Bit 9 set is detected.
			When the receiver wakes up, the RWU bit is cleared, and the first frame of data is
			received. If interrupts are enabled, the CPU is interrupted and the interrupt routine
			reads the message header to determine whether the message is intended for this DSP.
			If the message is for this DSP, the message is received, and RWU is set to wait for the
			next message. If the message is not for this DSP, the DSP immediately sets RWU.
			Setting RWU causes the DSP to ignore the remainder of the message and wait for the
			next message. Either a hardware RESET signal or a software RESET instruction
			clears RWU. RWU is ignored in Synchronous mode.
5	WAKE	0	Wakeup Mode Select
			When WAKE is cleared, the wakeup on Idle Line mode is selected. In the wakeup on
			idle line mode, the SCI receiver is re-enabled by an idle string of at least 10 or 11
			(depending on WDS mode) consecutive ones. The transmitter’s software must provide
			this idle string between consecutive messages. The idle string cannot occur within a
			valid message because each word frame there contains a start bit that is 0.
			When WAKE is set, the wakeup on address bit mode is selected. In the wakeup on
			address bit mode, the SCI receiver is re-enabled when the last (eighth or ninth) data bit
			received in a character (frame) is 1. The ninth data bit is the address bit (R8) in the
			11-bit multidrop mode; the eighth data bit is the address bit in the 10-bit asynchronous
			and 11-bit asynchronous with parity modes. Thus, the received character is an address
			that has to be processed by all sleeping processors—that is, each processor has to
			compare the received character with its own address and decide whether to receive or
			ignore all following characters.
4	SBK	0	Send Break
			A break is an all-zero word frame—a start bit 0, characters of all zeros (including any
			parity), and a stop bit 0 (that is, ten or eleven zeros, depending on the mode selected).
			If SBK is set and then cleared, the transmitter finishes transmitting the current frame,
			sends 10 or 11 0s, and reverts to idle or sending data. If SBK remains set, the
			transmitter continually sends whole frames of 0s (10 or 11 bits with no stop bit). At the
			end of the break code, the transmitter sends at least one high (set) bit before
			transmitting any data to guarantee recognition of a valid start bit. Break can signal an
			unusual condition, message, and so on, by forcing a frame error; the frame error is
			caused by a missing stop bit.
3	SSFTD	0	SCI Shift Direction
			Determines the order in which the SCI data shift registers shift data in or out: MSB first
			when set, LSB first when cleared. The parity and data type bits do not change their
			position in the frame, and they remain adjacent to the stop bit.

Serial Communication Interface (SCI) 8-15