Central Office Calls, Answering
Aspire Software Manual Features ◆213
➻15-07-01 : Programming Function Keys
To have outside calls ring specific keys, assign trunks to line keys (code *01 + trunk). You can
also program function keys as trunk group or loop keys (*02 or *05). For additional loop key
data, enter 0 (incoming only), 1 (outgoing only) or 2 (both ways).Use a Call Redirect key (49)
to allow a user to transfer a call to another extension or voice mail without answering the call.
Also, if needed, define keys for Private Call Refuse (86) or Caller ID Refuse (87) keys. When
either of these keys is enabled by the user, “Private” or “Caller ID Number Refusal” will be
activated for the trunks set to “1” in Program 14-01-27.
➪Aspire S: Trunks 1-8
➪Aspire: Trunks 1-100
➻15-13-01 : Loop Keys - Outgoing
Assign trunk groups for outgoing loop keys (0=ARS, Aspire S Trunk Groups 1-8, or Aspire Trunk
Groups 1-100).
➻15-13-02 : Loop Keys - Incoming
Assign trunk groups for incoming loop keys (0=all Trunk Groups, Aspire S Trunk Groups 1-8, or
Aspire Trunk Groups 1-100).
➻20-02-09 : System Options for Multi-Line Telephones - Disconnect Supervision
Enable (1) disconnect supervision for the system.
➻20-06-01 : Class of Service for Extensions
For Universal Answer, assign a Class of Service (1-15) to an extension that enables Program
20-10-07.
➻20-07-24 : Class of Service Options - Set/Cancel Private Call Refuse
In an extension’s Class of Service, enable (1) or disable (0) the extension’s ability to use the
Private Call Refuse service code or function key.
➻20-07-25 : Class of Service Options - Set/Cancel Caller ID Refuse
In an extension’s Class of Service, enable (1) or disable (0) the extension’s ability to use the
Caller ID Refuse service code or function key.
➻20-10-07 : Class of Service Options (Answer Service) - Automatic Answer of Universal Calls
In an extension’s Class of Service, enable (1) or disable (0) the extension’s ability to use Auto-
Answer to pick up Universal Answer calls. This allows a user to simply pick up the handset
instead of dialing a service code.
➻20-13-13 : Class of Service Options (Supplementary Service) - Continued Dialing
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to use Con-
tinued Dialing which allows DTMF signal sending while talking on extension.
➻20-13-23 : Class of Service Options (Supplementary Service) - Display the Reason for
Transfer
In an extension’s Class of Service, enable (1) or disable (0) an extension’s ability to display
the Reason for Transfer message.
➻21-01-15 : System Options for Outgoing Calls - Outgoing Disable on Incoming Line
Enable (1) or disable (0) the Outgoing Disable on Incoming Line feature.
➻21-01-16 : System Options for Outgoing Calls - Supervise Dial Detection Timer
With the Outgoing Disable on Incoming Line feature, if dial tone is not detected after the
extension answers an incoming line, the system determines the call is unable to complete and
releases the DTMF receiver (0-64800 Seconds).
➻21-01-17 : System Options for Outgoing Calls - Restriction Digit in Outgoing Disable on
Incoming Line
With the Outgoing Disable on Incoming Line feature, determine the number of digits (0-9) to
be dialed before the call should be disconnected.
➻22-01-01 : System Options for Incoming Calls, Incoming Call Priority
Use this option to determine if intercom calls or trunk calls have answer priority when both
are ringing simultaneously (0=intercom call priority, 1=trunk call priority). Refer to Program
15-02-22 for lamping conditions.