Direct Inward Dialing (DID)
Aspire Software Manual Features ◆287
➻25-06-02 : VRS/DISA One-Digit Code Attendant Setup
Set up single digit dialing for Automated Attendant callers. For each VRS Message pro-
grammed to answer outside calls, specify
●The digit the Automated Attendant caller dials (1-12, where 10=0, 11=* and 12=#). (Keep
in mind that if you assign destinations to digits 3 and 4, outside callers will not be able to
dial system extensions.)
●The destination reached (four digits maximum) when the caller dials the single digit code.
➻25-07-01 : System Timers for VRS/DISA - VRS Dial Tone Time
After answering a VRS/DISA trunk, the system waits this interval for the caller to dial the first
digit of the DISA password. If the caller fails to dial within this interval, the system drops the
call (0-64800).
➻25-07-02 : System Timers for VRS/DISA - VRS/DISA No Answer Time
A VRS/DISA caller can ring an extension for this interval before the system sets the call as a
Ring No Answer. After this interval expires, the call follows the programmed Ring No Answer
routing (set in Program 25-03 and 25-04) (0-64800).
➻25-07-04 : System Timers for VRS/DISA - Calling Time to Automatic Answering Tele-
phone Set
Set the answering waiting time of the automatic answering extension when an incoming DID
trunk call is received (0-64800).
➻25-07-05 : System Timers for VRS/DISA - Duration Time for Guidance Message by
Automatic Answering Telephone Set
Set the announcement time of the automatic answering extension after which in incoming
DID trunk caller is disconnected (0-64800).
➻25-07-06 : System Timers for VRS/DISA - Duration Time for Guidance Message by ACI
Set the announcement time by the ACI after which an incoming DID trunk caller is discon-
nected (0-64800).
➻25-07-11 : System Timers for VRS/DISA - VRS/DISA Answer Delay Timer
Set up the interval time the system will wait after receiving an incoming VRS/DISA call until
the system will automatically answer the call (0-64800).
➻25-07-13 : System Timers for VRS/DISA - VRS/DISA Busy Tone Interval
If a DISA caller dials a busy extension (and Program 25-04-01 = 0), the system plays busy
tone for this interval before disconnecting (0-64800).
➻25-07-14 : System Timers for VRS/DISA - Delayed DID Answer Timer
Assign the delay time from switching from a normal incoming status to DID mode. If this
time is set to ‘0’, the call will switch to DID mode immediately (0-64800).
➻30-03-01 : DSS Key Assignment
For DSS Consoles, assign a key for DID Mode Switching (88 + Program 22-17 table num-
ber). This key can be used to manually change the time pattern for a DID number. The follow-
ing LED indications are used with the key:
Pattern 1 = LED off, Pattern 2 = LED on, Pattern 3 = slow flash, Pattern 4 = fast flash, Patterns
5-8 = off
➻34-01-01 : E&M Tie Line Basic Setup - DID/E&M Start Signaling
Set the start signaling mode for DID and tie trunks. DID and tie trunks can use either immedi-
ate start or wink start signaling (0=2nd dial tone, 1=Wink, 2=Immediate, 3=Delay).
➻34-01-02 : E&M Tie Line Basic Setup - DID/E&M Incoming Signaling Type
Enter 0 if DID trunk is Dial Pulse (DP). Enter 1 if DID trunk is DTMF.
➻80-03-01 : DTMF Tone Receiver Setup
80-04-01 : Call Progress Tone Detector Setup
If required, modify the criteria for dial tone detection and call progress tone detection to set
the DTMF criteria for DTMF DID calls.