Vvid, Dot1p, Untagged, Trusted, Yes | Enterasys Networks 9034313-07

set ciscodp port

Parameters

status	Sets the CiscoDP port operational status.
disable	Does not transmit or process CiscoDP PDUs.

enable	Transmits and processes CiscoDP PDUs.

vvid	Sets the port voice VLAN for CiscoDP PDU transmission.

vlan‐id	Specifies the VLAN ID, range 1‐4093.

none	No voice VLAN will be used in CiscoDP PDUs. This is the default.

dot1p	Instructs attached phone to send 802.1p tagged frames.

untagged	Instructs attached phone to send untagged frames.

trusted	Sets the extended trust mode on the port.

yes	Instructs attached phone to allow the device connected to it to transmit
	traffic containing any CoS or Layer 2 802.1p marking. This is the default
	value.

no	Instructs attached phone to overwrite the 802.1p tag of traffic
	transmitted by the device connected to it to 0, by default, or to the value
	configured with the cos parameter.

cos value	Instructs attached phone to overwrite the 802.1p tag of traffic
	transmitted by the device connected to it with the specified value, when
	the trust mode of the port is set to untrusted. Value can range from 0 to
	7, with 0 indicating the lowest priority.

port‐string	Specifies the port(s) on which status will be set.

Defaults

•Status: enabled

•Voice VLAN: none

•Trust mode: trusted

•CoS value: 0

Mode

Switch mode, read‐write.

Usage

The following points describe how the Cisco DP extended trust settings work on the switch.

•A Cisco DP port trust status of trusted or untrusted is only meaningful when a Cisco IP phone is connected to a switch port and a PC or other device is connected to the back of the Cisco IP phone.

•A Cisco DP port state of trusted or untrusted only affects tagged traffic transmitted by the device connected to the Cisco IP phone. Untagged traffic transmitted by the device connected to the Cisco IP phone is unaffected by this setting.

•If the switch port is configured to a Cisco DP trust state of trusted (with the trusted yes parameter of this command), this setting is communicated to the Cisco IP phone instructing it to allow the device connected to it to transmit traffic containing any CoS or Layer 2 802.1p marking.

SecureStack C3 Configuration Guide 6-11

Page 143

Image 143

Enterasys Networks 9034313-07 manual Vvid, Dot1p, Untagged, Trusted, Yes

Contents

Enterasys SecureStack C3 Page Page Enterasys Networks, Inc. Firmware License Agreement Iii Page Contents Page Activating Licensed Features Discovery Protocol Configuration Configuring System Power and PoE Port Configuration Show port broadcast Set port broadcast Clear port broadcast Snmp Configuration Spanning Tree Configuration Configuring Spanning Tree Port Parameters Purpose Commands 802.1Q Vlan Configuration Port Priority Configuration Policy Classification Configuration Logging and Network Management Igmp Configuration 14-3 Rmon Configuration Dhcp Server Configuration Dhcp Snooping and Dynamic ARP Inspection Preparing for Router ModeIP Configuration IPv4 Routing Protocol Configuration 20-11 IPv6 Management IPv6 Configuration IPv6 Proxy Routing DHCPv6 Configuration OSPFv3 Configuration Authentication and Authorization Configuration 26-37 TACACS+ Configuration Tables SFlow ConfigurationAppendix a Policy and Authentication Capacities Index 10-4 22-26 Xxxii Important Notice Using This GuideAbout This Guide Structure of This Guide Structure of This Guide Related Documents SecureStack C3 Installation Guides Following icons are used in this guide Conventions Used in This GuideFollowing conventions are used in the text of this document Support@enterasys.com Getting Help Getting Help Xxxviii About This Guide SecureStack C3 CLI Overview Switch Management MethodsIntroduction Default Settings for Basic Switch Operation Factory Default Settings Feature Default Setting Sntp Default Settings for Router Operation Dvmrp Starting a CLI Session Using the Command Line InterfaceConnecting Using the Console Port Logging Connecting Using TelnetUsing a Default User Account Using an Administratively Configured User Account Getting Help with CLI Syntax Navigating the Command Line InterfaceCLI Command Defaults Descriptions CLI Command Modes Displaying Scrolling Screens Abbreviating and Completing Commands Basic Line Editing Commands Basic Line Editing Commands About SecureStack C3 Switch Operation in a Stack Configuring Switches in a Stack Installing a New Stackable System of Up to Eight Units Adding a New Unit to an Existing Stack Installing Previously-Configured Systems in a StackCreating a Virtual Switch Configuration SID Configuration Considerations About Using Clear Config in a StackIssues Related to Mixed Type Stacks Feature Support Purpose Stacking Configuration and Management CommandsShow switch Commands Examples Show switch switchtype None Show switch stack-ports Priority value Set switchSwitch command, read‐write Example This example shows how to renumber switch 5 to switch Set switch copy-fwSet switch description This example shows how to assign priority 3 to switch Set switch member Set switch movemanagement Use this command to remove a member entry from the stack Clear switch member Required CLI Setup Commands Basic ConfigurationQuick Start Setup Commands Optional CLI Setup Commands Setting User Accounts and Passwords Parameters Show system loginShow system login Output Details Super‐user read‐write read‐only Set system loginClear system login Use this command to remove a local login user account Switch command, read‐write Switch command, super‐user Set passwordThis example shows how to remove the netops user account Set system password aging Set system password length Show system lockout Set system password historyDisable Time time Set system lockoutShow system lockout Output Details Attempts attempts Setting Basic Switch Properties Show ip address Clear ip address Use this command to clear the system IP addressSet ip address Set ip protocol This example shows how to clear the system IP addressShow ip protocol Show system This example shows how to display system information Show system Output Details Show system hardware Slot Hardware Information Show system utilization This example sets the CPU utilization threshold to 75% Default threshold value is 80%Set system utilization Show system enhancedbuffermode Clear system utilization Set system enhancedbuffermode Set system temperatureEnable disable Enables or disables enhanced buffer mode This example shows how to enable enhanced buffer mode Trap enable disable Clear system temperatureSyslog enable Disable Set time Show time Show summertime This example shows how to set the system clock to 750 a.mUse this command to display daylight savings time settings If an offset is not specified, none will be applied Set summertimeSet summertime date If a zone name is not specified, none will be applied Set summertime recurring Set prompt Use this command to modify the command promptThis example shows how to set the command prompt to Switch Clear summertime Set banner motd Show banner motd Show version Clear banner motd Show version Output Details ‐5 provides an explanation of the command outputUse this command to configure a name for the system Set system name Set system contact Use this command to identify the location of the systemThis example shows how to set the system location string Set system location Set length This example shows how to set the system contact stringThis example shows how to set the terminal columns to Set width Set logout This example shows how to set the terminal length toThis example shows how to display the CLI logout setting Show logout Show console Use this command to display console settingsThis example shows how to display all console settings Use this command to set the console port baud rate Downloading via the Serial Port This example shows how to set the console port baud rate toDownloading a Firmware Image Downloading from a Tftp Server Type 2. The following baud rate selection screen displays Reverting to a Previous Image Reboot the system using the reset command page 3‐50 Reviewing and Selecting a Boot Firmware ImageShow boot system Compatibility platform specific Set boot system Show telnet Starting and Configuring TelnetThis example shows how to display Telnet status Use this command to enable or disable Telnet on the switch Outbound all Enable disableTelnet Inbound Configuration Persistence Mode Managing Switch Configuration and Files Set snmp persistmode Show snmp persistmode Manual Save configDir Auto Show file Use this command to display the contents of a file Show config Outfile ConfigureAll Systemimage CopyAppend Delete Show tftp settingsThis example shows how to download an image via Tftp This example sets the timeout period to 4 seconds Set tftp timeoutClear tftp timeout This example shows the output of this command This example sets the retry count to Set tftp retryClear tftp retry To clear the CLI screen or to close your CLI session This example shows how to clear the CLI screenClearing and Closing the CLI Cls clear screen This example shows how to exit a CLI session Resetting the SwitchReset Use either of these commands to leave a CLI session This example shows how to reset unit Clear configIf no unit ID is specified, the entire system will be reset This example shows how to reset the system Show webview Using and Configuring WebViewUse this command to display WebView status Show ssl Set webview Set ssl This example shows how to display SSL statusThis example shows how to enable SSL To gather common technical support information CommandGathering Technical Support Information Show support Set system hostprotect Configuring HostprotectHostprotect is enabled by default Show system hostprotect Clear system hostprotect This feature is disabled by defaultThis example disables hostprotect Default state is enabled Usage License Key Field Descriptions Activating Licensed FeaturesLicensing Procedure in a Stack Environment Adding a New Member to a Licensed Stack Clearing, Showing, and Applying Licenses Usage Set license Clear license Use this command to clear the license key settingsFeatureID feature The name of the feature being cleared Show license C3rw-clear license featureId advrouter Clear license Activating Licensed Features Use this command to display system power properties Configuring System Power and PoECommands Show inlinepower Show inlinepower Output Details Set inlinepower thresholdThis example shows how to display system power properties Sending of traps is disabled by default Set inlinepower trapSet inlinepower detectionmode Ieee Show port inlinepower High low Set port inlinepowerAdmin off auto Priority critical Set port inlinepower Configuring System Power and PoE Configuring CDP Discovery Protocol Configuration Show cdp Output Details Show cdp Set cdp state Auto disableEnable Set cdp interval Use this command to set a global CDP authentication codeSet cdp auth Clear cdp Set cdp hold-time Show neighbors Show ciscodp Configuring Cisco Discovery Protocol Show ciscodp Output Details ‐2 provides an explanation of the command output‐3 provides an explanation of the command output Show ciscodp port info Show ciscodp port info Output Details Set ciscodp timerThis example shows how to globally enable CiscoDP Set ciscodp status Set ciscodp port Set ciscodp holdtime Trusted VvidDot1p Untagged Clear ciscodp Overview Configuring Link Layer Discovery Protocol and LLDP-MEDTo review and configure Llpd and LLPD‐MED Configuration Tasks Show lldp Use this command to display Lldp configuration information Show lldp port trap Show lldp port status Show lldp port tx‐tlv port‐string Show lldp port tx-tlvShow lldp port location-info Show lldp port local-info 1000BASE-TFD Show lldp port local-info Output Details ECS Elin Show lldp port remote-info Voice Voice‐signalingGuest‐voice‐signaling Show lldp port network-policy Video‐conferencing Video‐signalingSet lldp tx-interval Softphone‐voice This example sets the transmit interval to 20 seconds Set lldp hold-multiplierSet lldp trap-interval Set lldp med-fast-repeat Set lldp port trap Tx‐enableRx‐enable Set lldp port status Elin Set lldp port med-trapSet lldp port location-info Set lldp port tx-tlv Link‐aggr GvrpMac‐phy Poe Vid vlan‐id dot1p State enable disableSet lldp port network-policy Tag tagged untagged Trap‐interval Clear lldpTx‐interval Hold‐multiplier Clear lldp port trap Clear lldp port status Cleared Clear lldp port med-trapClear lldp port location-info Dscp Clear lldp port network-policyTag Vid Clear lldp port tx-tlv Disables the LLDP‐MED Extended Power via MDI TLV from being Disables the LLDP‐MED Location Identification TLV from being Port type.unitorslot number.port number Port ConfigurationPort Configuration Summary Port String Syntax Used in the CLI Port Slot/Unit Parameters Used in the CLI Reviewing Port Status Show port status Show port Show port status Output Details Switch mib2Show port counters Show port counters Output Details This example clears the port counters for ge.3.1 Clear port countersShow port cablestatus Show port cablestatus Output Details Disabling / Enabling and Naming PortsThis example shows the cable status for 1 GE port ge.1.31 This example shows how to enable ge.1.3 Set port disableSet port enable This example shows how to disable ge.1.1 Set port alias Use this command to assign an alias name to a portShow port alias This example shows how to clear the alias for ge.3.3 This example shows how to assign the alias Admin to ge.3.3 Show port speed Setting Speed and Duplex Mode Mbps Set port speedShow port duplex 10 100 Full half This example shows how to set ge.1.17 to full duplexSet port duplex Show port jumbo Enabling / Disabling Jumbo Frame Support Clear port jumbo Enables or disables jumbo frame supportSet port jumbo Show port negotiation Setting Auto-Negotiation and Advertised Ability Show port advertise Enable disableSet port negotiation Set port advertise Clear port advertise Mdi Show port mdixSet port mdix Forced‐auto Optional Specify the port or ports to configure Configure ports to use MDI mode onlyConfigure ports to use Mdix mode only Set flowcontrol Setting Flow ControlShow flowcontrol This example shows how to enable flow control Show port trap Setting Port Link Traps and Link Flap Detection Show linkflap Following example disables sending trap on ge.3.1Set port trap Metrics GlobalstatePortstate Parameters Show linkflap metrics Output Details Show linkflap parameters Output Details Set linkflap portstate Disable enableDisables or enables the link flap detection function Set linkflap globalstate Set linkflap action Set linkflap interval Set linkflap threshold Use this command to set the link flap action trigger countClear linkflap action Clear linkflap down Set linkflap downtime Threshold interval Clear linkflapAll stats Parameter Show port broadcast Configuring Broadcast Suppression Clear port broadcast Set port broadcast Syntax Used in the CLI on page 7‐1 Remote Port Mirroring Mirroring FeaturesPort Mirroring Overview Configuring Smon MIB Port MirroringProcedures Show port mirroring To review and configure port mirroring on the device Set port mirroring Create disableCan be configured per stack, if applicable Set mirror vlan Use this command to clear a port mirroring relationshipClear port mirroring Clear mirror vlan Lacp Operation Link Aggregation Control Protocol Lacp Lacp Terms and Definitions ‐6 defines key terminology used in Lacp configurationLacp Terminology SecureStack C3 Usage Considerations Commands Show lacp ‐7 provides an explanation of the command output Show lacp Output Details Disable enable Disables or enables LacpThis example shows how to disable Lacp Set lacp Asyspri Set lacp aadminkeySet lacp asyspri Set lacp static Disable enable Disables or enables static link aggregationClear lacp Clear lacp static Clear lacp singleportlag This example enables the formation of single port LAGsSet lacp singleportlag Summary Counters Show port lacpStatus detail Set port lacp Aadminkey Padminport AadminstateLacptimeout Padminkey Clear port lacp C3su-clear port lacp port ge.3.16 Protected Port Operation Configuring Protected PortsSet port protected Read‐only Show port protectedClear port protected Show port protected name Set port protected name Clear port protected name Use this command to clear the name of a protected group Clear port protected name Port Configuration Snmp Configuration Summary Snmp Configuration About Snmp Security Models and Levels SNMPv1 and SNMPv2cSNMPv3 Snmp Security Levels Using Snmp Contexts to Access Specific MIBsConfiguration Considerations Reviewing Snmp Statistics Show snmp engineid Output Details This example shows how to display Snmp engine propertiesShow snmp engineid Show snmp counters Use this command to display Snmp traffic counter valuesThis example shows how to display Snmp counter values Show snmp counters Output Details Engine or otherwise unavailable Show snmp user Configuring Snmp Users, Groups, and Communities Set snmp user This example shows how to display an Snmp user list‐4 provides an explanation of the command output Use this command to create a new SNMPv3 user Nonvolatile AesSha Volatile Remote remote Clear snmp userShow snmp group V2c usm Volatile Set snmp groupUser user Security‐model V2c usm Clear snmp groupShow snmp community Context context Use this command to configure an Snmp community groupSet snmp community Securityname Clear snmp community Configuring Snmp Access RightsUse this command to delete an Snmp community name This example shows how to delete the community name vip Nonvolatile read‐ Only Show snmp accessNoauthentication Authentication Privacy Context context Show snmp access Output Details This example shows how to display Snmp access information‐6 provides an explanation of the command output Set snmp access Configuring Snmp MIB Views Clear snmp access Show snmp view Show snmp view Output Details Show snmp contextSet snmp view Clear snmp view Read‐only Configuring Snmp Target ParametersShow snmp targetparams Volatile nonvolatile Message‐ ‐8 provides an explanation of the command outputSet snmp targetparams Show snmp targetparams Output Details Protected from disclosure AuthenticationClear snmp targetparams Privacy Show snmp targetaddr Configuring Snmp Target AddressesUse this command to display Snmp target address information Udpport udpport Timeout timeoutSet snmp targetaddr Param param Tag 1 tag Use this command to delete an Snmp target address entryClear snmp targetaddr Taglist taglist About Snmp Notify Filters Configuring Snmp Notification Parameters Set newaddrtrap By default, this function is disabled globally and per portShow newaddrtrap Show snmp notify Trap inform ‐10 provides an explanation of the command outputSet snmp notify 10 show snmp notify Output Details Show snmp notifyfilter Use this command to clear an Snmp notify configurationClear snmp notify Subtree oid‐or‐ Set snmp notifyfilter Clear snmp notifyfilter Targetparam Show snmp notifyprofileSet snmp notifyprofile Clear snmp notifyprofile Creating a Basic Snmp Trap ConfigurationThis example shows how to delete Snmp notify profile area51 Example 11 Basic Snmp Trap Configuration Show snmp interface Configuring the Snmp Management InterfaceHow Snmp Will Use This Configuration Loopback loop‐ID Set snmp interface Clear snmp interface Clear snmp interface Snmp Configuration Spanning Tree Configuration Summary Spanning Tree Configuration Loop Protect Spanning Tree Features Configuring Spanning Tree Bridge Parameters For information about Active Show spantree statsSid sid Show spantree Output Details ‐1 shows a detailed explanation of command output Show spantree version Disable enable Globally disables or enables Spanning TreeSet spantree Set spantree version Show spantree bpdu-forwarding This example shows how to reset the Spanning Tree versionClear spantree version Set spantree bpdu-forwarding Disable enable Disables or enables Bpdu forwardingBy default Bpdu forwarding is disabled This example shows how to enable Bpdu forwarding 8021t Set spantree bridgeprioritymodeClear spantree bridgeprioritymode 8021d Create delete Show spantree mstilistSet spantree msti Fid fid Clear spantree mstiShow spantree mstmap Clear spantree mstmap This example shows how to map FID 3 to SIDUse this command to map a FID back to SID Set spantree mstmap Show spantree mstcfgid This example shows how to map FID 2 back to SIDShow spantree vlanlist Clear spantree mstcfgid Cfgname name Specifies an MST configuration nameSet spantree mstcfgid Clear spantree priority Use this command to set the device’s Spanning Tree prioritySet spantree priority Clear spantree hello This example shows how to reset the bridge priority on SIDSet spantree hello Set spantree maxage Use this command to set the bridge maximum aging time Clear spantree maxage Set spantree fwddelayUse this command to set the Spanning Tree forward delay Show spantree backuproot Clear spantree fwddelay Clear spantree backuproot Set spantree backuproot Set spantree tctrapsuppress Show spantree tctrapsuppress Set spantree protomigration Clear spantree tctrapsuppress Set spantree spanguard Enable disable Enables or disables the SpanGuard functionShow spantree spanguard Clear spantree spanguard This example shows how to enable the SpanGuard function Set spantree spanguardtimeout Show spantree spanguardtimeout Show spantree spanguardlock Clear spantree spanguardtimeout Clear / set spantree spanguardlock Show spantree spanguardtrapenableThis example shows how to unlock port ge.1.16 Is enabled Set spantree spanguardtrapenableClear spantree spanguardtrapenable Set spantree legacypathcost Show spantree legacypathcost This example clears the legacy path cost to 802.1t values Clear spantree legacypathcostShow spantree autoedge Set spantree autoedge Clear spantree autoedge To display and set Spanning Tree port parameters Configuring Spanning Tree Port ParametersSet spantree portadmin Disable enable This example shows how to disable Spanning Tree on ge.1.5 Clear spantree portadminShow spantree portadmin Set spantree portpri Use this command to set a port’s Spanning Tree priorityShow spantree portpri Clear spantree portpri Set spantree adminpathcost Show spantree adminpathcost Show spantree adminedge Clear spantree adminpathcost True false Set spantree adminedgeClear spantree adminedge This example shows how to set ge.1.11 as an edge port Show spantree operedge This example shows how to reset ge.1.11 as a non‐edge port Configuring Spanning Tree Loop Protect Parameters If no SID is specified, SID 0 is assumed This example shows how to enable Loop Protect on ge.2.3Set spantree lp Show spantree lp Show spantree lplock Clear spantree lp SID Locked Clear spantree lplock Show spantree lpcapablepartner Set spantree lpcapablepartner Set spantree lpthreshold Use this command to set the Loop Protect event thresholdClear spantree lpcapablepartner Clear spantree lpthreshold None. The default event threshold isShow spantree lpthreshold Show spantree lpwindow Set spantree lpwindow Clear spantree lpwindow Set spantree lptrapenableDisabled Clear spantree lptrapenable Show spantree lptrapenable Set spantree disputedbpduthreshold Clear spantree disputedbpduthreshold Show spantree disputedbpduthreshold Show spantree nonforwardingreason Vlan Configuration Summary 802.1Q Vlan Configuration Creating a Secure Management Vlan Command Set for Creating a Secure Management Vlan Portinfo Viewing VLANsShow vlan Static Vlan Vlan ID Name Show vlan Output Details Set vlan Create enable Creates, enables or disables VLANs. disableThis example shows how to create Vlan Creating and Naming Static VLANs Clear vlan This example shows how to set the name for Vlan 7 to greenSet vlan name Clear vlan name This example shows how to clear the name for Vlan Show port vlan Assigning Port Vlan IDs PVIDs and Ingress Filtering No‐modify‐egress Set port vlanClear port vlan Modify‐egress Show port ingress filter Show port discard Set port ingress filter Tagged untagged both none Set port discard Show port egress Configuring the Vlan Egress List Set vlan forbidden Untagged forbidden tagged Use this command to remove ports from a VLAN’s egress listSet vlan egress Clear vlan egress Forbidden Show vlan dynamicegress Set vlan dynamicegress Enable disable Enables or disables dynamic egressThis example shows how to enable dynamic egress on Vlan Set host vlan Setting the Host VlanShow host vlan Clear host vlan This example shows how to set Vlan 7 as the host Vlan How It Works Enabling/Disabling Gvrp Garp Vlan Registration ProtocolAbout Garp Vlan Registration Protocol Gvrp Example of Vlan Propagation via Gvrp Show gvrp Show garp timerUse this command to display Gvrp configuration information Set gvrp Show gvrp configuration Output DetailsDisables or enables Gvrp on the device Clear gvrp Set garp timerThis example shows how to enable Gvrp on ge.1.3 Leave Clear garp timerLeaveall timer‐ Join C3su-clear garp timer leave ge.1.1 Policy Classification Configuration Summary Policy Classification Configuration ‐verbose Configuring Policy ProfilesUse this command to display policy profile information Show policy profile Show policy profile Output Details Set policy profile Clear policy profile Use this command to delete a policy profile entryThis example shows how to delete policy profile Show policy rule Configuring Classification RulesAll admin‐ profile profile‐ index Udpdestport Not‐in‐service Not‐ready Storage‐type non‐Admin‐pid Tcpsourceport Show policy rule Output Details Show policy capability Vlan Vlantag data Admin‐profileSet policy rule Ipsourcesocket EtherIpproto Ipdestsocket Data value Mask bits Valid Values for Policy Classification Rules All‐pid‐entries Following parameters apply to deleting an admin ruleClear policy rule Range from 1 to 4094 or 0xFFF Clear policy all-rules Use this command to remove all policy classification rules To assign and unassign ports to policy profiles Use this command to assign ports to a policy profileAssigning Ports to Policy Profiles Set policy port Clear policy port Procedure 11-1 User-Defined CoS Configuration Configuring Policy Class of Service CoSAbout Policy-Based CoS Configurations Configuring Policy Class of Service CoS About CoS-Based Flood Control Procedure Set cos state Use this command to enable or disable Class of Service Clear cos state This example shows how to enable Class of ServiceShow cos state Irl‐reference Set cos settingsPriority priority Tos‐value tos‐value Tos‐value Clear cos settingsShow cos settings Priority Set cos port-config Should be displayed Show cos port-config Ports Clear cos port-configEntry Name Set cos port-resource irl Multicast Set cos port-resource flood-ctrlGroup#.port‐type Unicast Group#.port‐type Show cos port-resource Type Clear cos port-resource irlUnit Rate Multicast Clear cos port-resource flood-ctrlSet cos reference Unicast Rate‐limit irl‐index Specifies that an IRL reference is being configuredShow cos reference IRL reference number associated with this entry Clear cos reference Pps Show cos unitPort‐typ e index Kbps Show cos port-type Clear cos all-entries This example shows flood control information for port type Port Priority Configuration Summary Port Priority Configuration Show port priority Configuring Port Priority Clear port priority Set port priority Show port priority-queue Configuring Priority to Transmit Queue Mapping Set port priority-queue Clear port priority-queue Show port txq Configuring Quality of Service QoS Set port txq Clear port txq By default, transmit queues are defined as follows Clear port txq Port Priority Configuration About IP Multicast Group Management Igmp ConfigurationIgmp Overview About Multicasting Configuring Igmp at LayerTo configure Igmp snooping from the switch CLI Use this command to enable or disable Igmp on the system Set igmpsnooping adminmodeUse this command to display Igmp snooping information This example shows how to display Igmp snooping information Set igmpsnooping interfacemode This example shows how to enable Igmp on the systemEnable disable Enables or disables Igmp This example shows how to enable Igmp on port ge.1.10 Set igmpsnooping maxresponse If no ports are specified, all ports are added to the entry Set igmpsnooping mcrtrexpiretimeSet igmpsnooping add-static Modify If modify is not specified, a new entry is created Set igmpsnooping remove-staticShow igmpsnooping static Stats Optional Displays Mfdb statistics Show igmpsnooping mfdbGroup group This example displays the static Igmp ports for Vlan Clear igmpsnooping Use this command to clear all Igmp snooping entriesThis example shows how to clear all Igmp snooping entries Ip igmp Configuring Igmp on Routing InterfacesTo configure Igmp on routing interfaces Global configuration C3su‐routerConfig# Ip igmp version Ip igmp enableThis example shows how to enable Igmp on the router Interface configuration C3su‐routerConfig‐ifVlan 1# Show ip igmp interface Any router mode Ip igmp query-interval Show ip igmp groups Ip igmp startup-query-interval Ip igmp query-max-response-time Ip igmp last-member-query-interval Ip igmp startup-query-count Ip igmp robustness Ip igmp last-member-query-count Interface configuration C3 su‐routerConfig‐ifVlan 1# Ip igmp robustness Igmp Configuration Logging and Network Management Configuring System Logging Show logging server Set logging server Clear logging server Show logging default Use this command to set logging default values Set logging default Severity Clear logging defaultShow logging application Facility Show logging application Output Details Set logging application If level is not specified, none will be applied Level level Show logging local Clear logging application Clear logging local Set logging local Show logging interface This example shows how to clear local loggingShow logging buffer Set logging interface Clear logging interface History Monitoring Network Events and Status Set history Use this command to set the size of the history bufferDefault Show history This example, the host at IP address is not responding PingShow users Console DisconnectShow netstat Show netstat Output Details Following example shows the output of this commandFollowing table describes the output of this command Show arp Managing Switch Network Addresses and RoutesUse this command to display the switch’s ARP table Show arp Output Details This example shows how to display the ARP tableSet arp Traceroute Clear arp Self mgmt Show macEach response Type other learned Show mac Output Details Show mac agetime Clear mac agetime This example shows how to display the MAC timeout periodThis example shows how to set the MAC timeout period Set mac agetime Show mac algorithm Default MAC algorithm is mac‐crc16‐upperbitsSet mac algorithm Set mac multicast Clear mac algorithm Append clear Use this command to remove a multicast MAC addressClear mac address Set mac unreserved-flood Show mac unreserved-flood Show sntp Configuring Simple Network Time Protocol SntpThis example enables multicast flood protection Use this command to display Sntp client settings Show sntp Output Details This example shows how to display Sntp client settings Clear sntp client Set sntp client If precedence is not specified, 1 will be applied Set sntp serverClear sntp server Clear sntp poll-interval Set sntp poll-interval Clear sntp poll-retry This example shows how to clear the Sntp poll intervalSet sntp poll-retry This example shows how to clear the Sntp poll timeout Set sntp poll-timeoutClear sntp poll-timeout Use this command to clear the Sntp poll timeout Set timezone Set sntp interface Show sntp interface Clear sntp interface C3rw-show sntp interface Vlan 100 C3rw-clear sntp interface Show nodealias config Configuring Node Aliases Maxentries maxentries Show nodealias config Output DetailsSet nodealias Clear nodealias config Rmon Monitoring Group Functions Rmon ConfigurationRmon Monitoring Group Functions and Commands Design Considerations Group What It Does What It Monitors CLI Commands To display, configure, and clear Rmon statistics Statistics Group Commands Set rmon stats Use this command to configure an Rmon statistics entryShow rmon stats If owner is not specified, monitor will be applied To‐defaultsThis example shows how to delete Rmon statistics entry Clear rmon stats Show rmon history History Group Commands Interval interval Set rmon historyClear rmon history Buckets buckets This example shows how to delete Rmon history entry This example shows how to display Rmon alarm entry Alarm Group CommandsShow rmon alarm Type absolute Set rmon alarm propertiesShow rmon alarm Output Details Object object Set rmon alarm status Use this command to delete an Rmon alarm entry Clear rmon alarmEnable This example shows how to enable Rmon alarm entry Show rmon event Event Group CommandsUse this command to display Rmon event entry properties This example shows how to display Rmon event entry Trap both Set rmon event propertiesDescription Type none log Clear rmon event This example shows how to enable Rmon event entrySet rmon event status This example shows how to clear Rmon event Show rmon channel Filter Group Commands Failed Use this command to configure an Rmon channel entrySet rmon channel Accept matched Channel channel Clear rmon channelShow rmon filter Index index Set rmon filter Clear rmon filter Use this command to clear an Rmon filter entryThis example shows how to clear Rmon filter entry Nodata Packet Capture CommandsShow rmon capture Loadsize loadsize Set rmon captureAction lock Slice slice Clear rmon capture Use this command to clears an Rmon capture entryThis example shows how to clear Rmon capture entry Dhcp Server Dhcp Server ConfigurationDhcp Overview Dhcp Relay Agent Configuring a Dhcp Server Configuring General Dhcp Server Parameters Set dhcp Set dhcp bootpThis example enables Dhcp server functionality Show dhcp conflict This example enables address allocation for Bootp clientsThis example enables Dhcp conflict logging Set dhcp conflict logging Clears the conflict information for all IP addresses Logging Disables conflict loggingThis example disables Dhcp conflict logging Clear dhcp conflict Clear dhcp exclude 100, with the set dhcp exclude commandSet dhcp exclude This example sets the number of ping packets sent to Set dhcp pingClear dhcp ping Clear dhcp binding Show dhcp binding Clear dhcp server statistics Use this command to display Dhcp server statisticsUse this command to clear all Dhcp server counters Show dhcp server statistics This example clears all Dhcp server counters Manual Pool Configuration Considerations Configuring IP Address Pools This example creates an address pool named auto1 Set dhcp pool This example deletes the address pool named auto1 Use this command to delete a Dhcp server pool of addressesClear dhcp pool Set dhcp pool network Set dhcp pool hardware-address Clear dhcp pool network If no type is specified, Ethernet is assumed Clear dhcp pool hardware-addressSet dhcp pool host Set dhcp pool client-identifier Clear dhcp pool host Clear dhcp pool client-identifier Clear dhcp pool client-name Set dhcp pool client-name Clear dhcp pool bootfile Set dhcp pool bootfile Clear dhcp pool next-server Set dhcp pool next-server Infinite Set dhcp pool leaseClear dhcp pool lease Clear dhcp pool default-router Set dhcp pool default-router Clear dhcp pool dns-server Set dhcp pool dns-server Clear dhcp pool domain-name Set dhcp pool domain-name Clear dhcp pool netbios-name-server Set dhcp pool netbios-name-server ‐node Set dhcp pool netbios-node-typeClear dhcp pool netbios-node-type Ascii string Set dhcp pool option This example removes option 19 from address pool auto1 Show dhcp pool configurationClear dhcp pool option Show dhcp pool configuration Dhcp Message Processing Dhcp Snooping Dynamic ARP InspectionDhcp Snooping Overview Building and Maintaining the Database Rate Limiting Basic ConfigurationConfiguration Notes Procedure 17-1 Basic Configuration for Dhcp Snooping Set dhcpsnooping Dhcp Snooping CommandsDisabled globally Set dhcpsnooping vlan Set dhcpsnooping database write-delay Set dhcpsnooping trust By default, ports are untrusted Set dhcpsnooping verify This example configures port ge.1.1 as a trusted portSet dhcpsnooping binding Against the client hardware address Source MAC address verification is enabled by defaultSet dhcpsnooping log-invalid Burst interval secs Set dhcpsnooping limitNone Rate pps This example configures rate limit parameters on port ge.1.1 Show dhcpsnooping port Show dhcpsnooping database Entry, either dynamic or static Show dhcpsnooping bindingDynamic static Show dhcpsnooping statistics Clear dhcpsnooping database Clear dhcpsnooping bindingClear dhcpsnooping statistics Dynamic ARP Inspection Overview Write‐delayDefault value of 300 seconds Clear dhcpsnooping limit Optional ARP Packet Validation Functional DescriptionStatic Mappings Eligible Interfaces Logging Invalid PacketsPacket Forwarding Rate Limiting Step Task Commands Procedure 17-2 Basic Dynamic ARP Inspection Configuration Vlan Configuration Example ConfigurationRouter Configuration Dynamic ARP Inspection Configuration Dynamic ARP Inspection CommandsSet arpinspection vlan Dhcp Snooping Configuration Logging Set arpinspection trustLogging is disabled by default By default, all physical ports and LAGs are untrusted Dst‐mac Set arpinspection validateSrc‐mac Set arpinspection limit Mac host Set arpinspection filterShow arpinspection access-list Permit This example displays the ARP configuration of lag.0.1 Show arpinspection ports Show arpinspection statistics Show arpinspection vlan This example removes all 3 additional validation conditions Clear arpinspection validateWith an invalid address Clear arpinspection vlan Clear arpinspection filter This example removes the ARP ACL named staticARP from Vlan Clear arpinspection limit This example clears all DAI statistics from the switch Clear arpinspection statisticsPage Pre-Routing Configuration Tasks Preparing for Router Mode Router CLI Configuration Modes Enabling Router Configuration ModesEnabling the Switch for Routing Router CLI Configuration Modes Page Configuring Routing Interface Settings IP Configuration Vlan vlan ‐id Show interface Vlan vlan‐ id Use this command to configure interfaces for IP routingRouter global configuration mode C3su‐routerConfig# Interface Show ip interface This example shows how to enter configuration mode for Vlan Secondary Router interface configuration C3su‐routerConfig‐ifVlan 1#Ip address Show ip interface Output Details No shutdown Show running-config No ip routing This example shows how to enable Vlan 1 for IP routing Interface tunnel Configuring Tunnel InterfacesUse this command to configure a tunnel interface Tunnel source This example creates a configured tunnel interfaceRouter interface configuration C3su‐routerConfig‐ifTnnl 1# No form of this command removes the mode of the tunnel Tunnel modeThis command specifies the mode of the tunnel interface Ipv6ip Specifies that the tunnel mode is IPv6 over IPv4 Show interface tunnel This example sets the tunnel mode to IPv6 over IPv4 Show ip arp Reviewing and Configuring the ARP Table Show ip arp Output Details This example shows how to use the show ip arp commandArp Ip proxy-arp This example shows how to enable proxy ARP on Vlan Privileged Exec C3su‐router# Arp timeoutClear arp-cache 14,400 seconds Ip directed-broadcast Configuring Broadcast SettingsInterface configuration C3su‐Router1Config‐ifVlan 1# Are forwarded Ip forward-protocolUdp Specifies UDP as the IP forwarding protocol Ip helper-address Show ip route Reviewing IP Traffic and Configuring Routes OSPF, IA Preference in route selection Ip routePing Traceroute This command is also available in switch modeThere is also a traceroute command available in switch mode Ip icmp redirect enable Configuring Icmp Redirects Interface Show ip icmp redirect Activating Advanced Routing Features IPv4 Routing Protocol Configuration Router rip Configuring RIPRIP Configuration Task List and Commands RIP Configuration Task List and Commands Distance Ip rip enableThis example shows how to enable RIP R1compatible Ip rip send version Specifies RIP version Ip rip authentication-keySpecifies RIP version 1. This is the default setting Ip rip receive version Md5 Ip rip message-digest-key Split-horizon poison Use this command to disable automatic route summarizationRouter configuration C3su‐routerConfig‐router# No auto-summary Passive-interface Ospf Receive-interfaceRedistribute Connected Subnetted will be redistributed Command detailed in ip route on page 19‐21Protocol Subnets Advanced License Required Configuring OspfOspf Configuration Task List and Commands Ospf Configuration Task List and Commands Routes Router id 1583compatibility This example shows how to enable routing for Ospf processRouter ospf Ip ospf areaid Ip ospf enableThis example shows how to enable RFC 1583 compatibility Ip ospf priority Ip ospf cost Timers spf Ip ospf retransmit-interval Ip ospf transmit-delay 65535 Ip ospf hello-intervalIp ospf dead-interval Ip ospf authentication-key Distance ospf Ip ospf message digest key md5 Intra‐area routes Area rangeExternal inter‐ Area intra‐area Advertise If not specified, advertise mode will be setArea stub Advertise no‐ Area nssa Area default cost Information‐ Default‐This example shows how to configure area 10 as an Nssa area Area virtual-link Dead‐interval Authentication‐Transmit‐delay Key key Metric‐type type Show ip ospfRip Show ip ospf database This example shows how to display Ospf informationUse this command to display the Ospf link state database Show ip ospf database Output Details Show ip ospf interface Show ip ospf interface Output Details Show ip ospf neighbor Output Details Show ip ospf neighbor Show ip ospf virtual links Output Details Show ip ospf virtual-linksClear ip ospf process This example shows how to reset Ospf process Enabling Dvmrp on an Interface Configuring Dvmrp Ip dvmrp Ip dvmrp enableCommands to Enable Dvmrp on an Interface This example shows how to enable the Dvmrp process Show ip dvmrp Use this command to display Dvmrp routing informationIp dvmrp metric This example shows how to display Dvmrp status information Ip irdp enable Configuring Irdp Ip irdp minadvertinterval Ip irdp maxadvertinterval 9000 Ip irdp holdtimeIp irdp preference Show ip irdp Use this command to display Irdp informationIp irdp broadcast Configuration Tasks on page 18‐1 Router vrrp Configuring Vrrp Create This example shows how enable Vrrp configuration mode Address Advertise-interval Priority Preempt Described in Pre‐Routing Configuration Tasks on page 18‐1 Enable Show ip vrrp Ip vrrp authentication-keyUse this command to display Vrrp routing information This example shows how to display Vrrp information Design Considerations Configuring PIM-SM Ip pimsm staticrp Global router configuration C3su‐routerConfig#This example shows how to globally enable and disable PIM Ip pimsm Ip pimsm enable Show ip pimsm This example shows how to display PIM informationIp pimsm query-interval Show ip pimsm Output Details This example shows how to display PIM router informationShow ip pimsm componenttable Stats This example shows how to display PIM interface informationShow ip pimsm interface Show ip pimsm componenettable Output Details 10 show ip pimsm interface stats Output Details This example shows how to display PIM interface statisticsShow ip pimsm neighbor Show ip pimsm interface vlan Output Details Candidate ‐11 provides an explanation of the command outputShow ip pimsm rp 11 show ip pimsm neighbor Output Details 12 show ip pimsm rp Output Details ‐12 provides an explanation of the command outputShow ip pimsm rphash Display the PIM‐SM static Rendezvous Point information ‐13 provides an explanation of the command outputShow ip pimsm staticrp 13 show ip pimsm staticrp Output Details Use this command to display the IP multicast routing tableShow ip mroute 20-60 IPv4 Routing Protocol Configuration Show ipv6 status IPv6 Management Set ipv6 By default, IPv6 management is disabledThis example shows how to enable IPv6 management Eui64 No global unicast IPv6 address is defined by defaultSet ipv6 address Clear ipv6 address Use this command to clear IPv6 global addressesShow ipv6 address Set ipv6 gateway Show ipv6 neighbors Use this command to clear an IPv6 gateway addressClear ipv6 gateway Show ipv6 netstat This example shows example output of this commandUse this command to display IPv6 netstat information Size num This command is also available in router modePing ipv6 Traceroute ipv6 Traceroute ipv6 21-10 IPv6 Management IPv6 Routing License Required IPv6 ConfigurationOverview Following table lists the default IPv6 conditions Default Conditions Ipv6 hop-limit General Configuration CommandsIpv6 forwarding This example sets the hop limit to Default maximum number of IPv6 hops isThis command configures static IPv6 routes Ipv6 route Ipv6 route distance Default preference or administrative distance is Ipv6 unicast-routing This command sets the default distance value to Link‐local‐address Ping ipv6 interface Router privileged exec C3 su‐router# 20010db8123455551 No IPv6 addresses are defined for any interface Interface Configuration CommandsIpv6 address IPv6 is disabled Ipv6 enable Bytes Ipv6 mtu This example sets the MTU value to 1500 bytes This example clears all dynamically learned cache entries Neighbor Cache and Neighbor Discovery CommandsClear ipv6 neighbors Ipv6 nd ns-interval Duplicate address detection enabled, for 1 attemptIpv6 nd dad attempts This example sets the NS interval to 2 seconds By default, a value of 0 is advertised in RA messagesRouter interface configurationC3su‐routerConfig‐ifVlan 1# Ipv6 nd reachable-time This example sets the reachable time to 60 seconds Ipv6 nd other-config-flagFlag is set to false by default Router interface configuration C3su‐routerConfig‐if Vlan 1# Ipv6 nd ra-lifetime Ipv6 nd ra-interval Ipv6 nd prefix Suppression disabledThis example disables router advertisement transmission Ipv6 nd suppress-ra Off‐link No‐autoconfigRouter interface configurationC3su‐routerConfig‐if Vlan 1# Example Router privileged execution C3su‐router# Query CommandsShow ipv6 Show ipv6 interface This example displays information about IPv6 interface Vlan This example displays the neighbors in the cache This command displays IPv6 Neighbor Cache information Interface interface This command displays the IPv6 routing tableShow ipv6 route Show ipv6 neighbor Output Details Show ipv6 route Output Details This example displays all active IPv6 routes Show ipv6 route preferences Output Details Show ipv6 route preferences Non‐best routes This command displays the summary of the routing tableShow ipv6 route summary Show ipv6 summary Output Details Following example displays the output of this commandShow ipv6 traffic Show ipv6 traffic Output Details Options, etc Counter would include datagrams counted Send. Note that this counter includes all those counted by This example clears the statistics for Vlan Clear ipv6 statisticsRouter privileged executionC3su‐router# IPv6 Proxy Routing Limitations Preparing a Mixed Stack for IPv6 Proxy Routing Ipv6 proxy-routing IPv6 proxy routing is disabled by defaultRouter global configuration C2su‐routerConfig# This example enables IPv6 proxy routing Any routing mode DHCPv6 Configuration This command enables DHCPv6 on the router Global Configuration CommandsIpv6 dhcp enable Following table lists the default DHCPv6 conditions Ipv6 dhcp relay-agent-info-opt By default, DHCPv6 is disabledThis example enables DHCPv6 Ipv6 dhcp pool Ipv6 dhcp relay-agent-info-remote-id-subopt Ipv6 dhcp pool Domain-name Address Pool Configuration Commands Prefix-delegation Dns-server Secs infinite Valid‐lifetime secsPreferred‐lifetime C3su-routerConfig-dhcp6s-pool# exit C3su-routerConfig# Preference pref By default, DHCPv6 functionality is disabledIpv6 dhcp server Rapid‐commit Remote‐id duid‐ifid Ipv6 dhcp relayDestination dest‐addr Interface intf Examples Show ipv6 dhcp DHCPv6 Show Commands Statistics Show ipv6 dhcp interface This example displays the DHCPv6 statistics for Vlan Output of show ipv6 dhcp interface Command Show ipv6 dhcp statistics This example displays the output of this commandOutput of show ipv6 dhcp statistics Command This example clears DHCPv6 statistics for Vlan Clear ipv6 dhcp statistics Show ipv6 dhcp binding This command displays information about DHCPv6 bindingsShow ipv6 dhcp pool If no IPv6 address is specified, all bindings are displayed Show ipv6 dhcp binding DHCPv6 Configuration OSPFv3 Configuration Following table lists the default OSPFv3 conditions Ipv6 router id Global OSPFv3 Configuration CommandsUse this command to configure the OSPFv3 router ID Metric value Default-information originateIpv6 router ospf Always Router OSPFv3 configuration C3su-routerConfig-router# Default-metricRouter OSPFv3 configuration C3su‐routerConfig‐router# No default metric is configured Type1 Exit-overflow-intervalIntra Inter This example sets the exit overflow interval to 10 seconds This command configures the external Lsdb limit for OSPFv3Default value is ‐1 External-lsdb-limit Tag tag Maximum-pathsConnected static Metric = unspecified Metric type = Type Tag = These commands are used to configure area parameters Area Configuration CommandsArea default-cost This example shows how to configure area 20 as an Nssa This example sets the default route cost to 50 for area Comparable Area nssa default-info-originateDefault metric value is Area nssa no-redistribute Area nssa no-summary Area nssa translator-stab-intv This command configures the translator role of the routerBy default, the translator role is disabled Area nssa translator role Nssaexternallink Default interval is 40 secondsArea address ranges are not configured by default Summarylink This command creates a stub area for the specified area ID This example creates a stub area with the ID Example disables the import of summary LSAs into stub areaArea stub no-summary Area virtual-link dead-interval Default dead interval is 40 seconds Area virtual-link retransmit-interval Default hello interval is 10 secondsArea virtual-link hello-interval Default transmit delay is 1 second Area virtual-link transmit-delayDefault retransmit interval is 5 seconds OSPFv3 is disabled by default Ipv6 ospf enable Ipv6 ospf cost Ipv6 ospf areaid Ipv6 ospf dead-interval Default dead interval value is 40 seconds Ipv6 ospf mtu-ignore Ipv6 ospf hello-interval Ipv6 ospf network By default, MTU mismatch detection is enabledDefault network type is broadcast Ipv6 ospf retransmit-interval Default priority value isIpv6 ospf priority Default value is 1 second Ipv6 ospf transmit-delayDefault value is 4 seconds Ipv6 ospf transmit-delay Show ipv6 ospf OSPFv3 Show CommandsThis command displays OSPFv3 router information This example shows how to display OSPFv3 router information Show ipv6 ospf Output Details Show ipv6 ospf area Output Details Show ipv6 ospf area Show ipv6 ospf abr Output Details Show ipv6 ospf abr Show ipv6 ospf asbr Output Details Show ipv6 ospf asbr Show ipv6 ospf database Adv Router Link Id Age Sequence Csum Options Rtr Opt Show ipv6 ospf database Output Details Show ipv6 ospf database database-summary Output Details Loopback loopid This command displays information about OSPFv3 interfacesShow ipv6 ospf interface Show ipv6 ospf interface Command Output Details Show ipv6 ospf interface stats This example shows how to display statistics for Vlan Show ipv6 ospf interface stats Output Details Specify the tunnel interface to display This command displays information about OSPFv3 neighborsShow ipv6 ospf neighbor Specify the Vlan interface to display information about Show ipv6 ospf neighbor Output Details This example displays range information for area Show ipv6 ospf range10 show ipv6 ospf neighbor routerid Output Details 12 show ipv6 ospf stub table Output Details Show ipv6 ospf stub table11 show ipv6 ospf range Output Details This example displays the OSPFv3 stub table information 13 show ipv6 ospf virtual-link Output Details Show ipv6 ospf virtual-link Show ipv6 ospf virtual-link Show ipv6 ospf virtual-link OSPFv3 Configuration Overview of Authentication and Authorization Methods Authentication and Authorization Configuration Overview of Authentication and Authorization Methods Filter-ID Attribute Formats Use this command to set the authentication login method Setting the Authentication Login MethodShow authentication login Set authentication login Radius Clear authentication loginAny Local Retries Configuring RadiusTimeout Show radius Servers or a specific Radius server as defined by an index Optional Displays Radius server configuration informationSet radius Server Server index Timeout timeoutRealm management‐ access any network‐access Realm Clear radius Retries retries Show radius accountingSet radius accounting Retries This example shows how to set Radius accounting retries toTimeout Clear radius accounting Set radius interface Show radius interface Clear radius interface Example Auth‐stats Configuring 802.1X AuthenticationShow dot1x Auth‐diag This example shows how to display 802.1X status Show dot1x auth-config True false Set dot1xInit reauth Set dot1x auth-config Portcontrol Maxreq Clear dot1x auth-config Show eapol Show eapol Output Details Connecting state, via disconnected Forced‐auth Set eapolClear eapol Auth‐mode Optional Globally clears the Eapol authentication mode Show macauthentication Configuring MAC Authentication Nopassword Show macauthentication Output Details Show macauthentication session Output Details Show macauthentication sessionThis example shows how to display MAC session information Use this command to set a MAC authentication password Set macauthenticationSet macauthentication password Enables or disables MAC authentication Clear macauthentication passwordSet macauthentication port Use this command to clear the MAC authentication password Set macauthentication portquietperiod Set macauthentication portinitialize This example resets the default quiet period on port Clear macauthentication portquietperiodSet macauthentication macinitialize Enables or disables MAC reauthentication Set macauthentication reauthenticationSet macauthentication portreauthenticate Set macauthentication reauthperiod Set macauthentication macreauthenticate Clear macauthentication reauthperiod Clear macauthentication significant-bits Set macauthentication significant-bits C3su-clear macauthentication significant-bits About Multi-User Authentication Configuring Multiple Authentication MethodsAbout Multiple Authentication Types Show multiauth Strict Set multiauth modeClear multiauth mode Multi Clear multiauth precedence Default precedence order is dot1x, pwa, macSet multiauth precedence Set multiauth port Show multiauth port Clear multiauth port Show multiauth session Show multiauth station Agent dot1x mac Show multiauth idle-timeout Idle timeout value is provided by the authenticating server Set multiauth idle-timeoutAuthentication method for which to set the timeout value Which to set the timeout value Which to reset the timeout value to its default Clear multiauth idle-timeoutShow multiauth session-timeout Default Which to set the session timeout value Set multiauth session-timeout Configuring User + IP Phone Authentication Clear multiauth session-timeout Configuring Vlan Authorization RFC Tagged Set vlanauthorizationSet vlanauthorization egress By default, administrative egress is set to untagged Clear vlanauthorizationShow vlanauthorization Show vlanauthorization Output Details Configuring Policy Maptable Response Operational Description When Policy Maptable Response is Both Show policy maptable When Policy Maptable Response is PolicyWhen Policy Maptable Response is Tunnel Policy Set policy maptableResponse Both Clear policy maptable To review, disable, enable, and configure MAC locking Configuring MAC Locking Show maclock Connected to MAC locked ports Show maclock stationsShow maclock Output Details Firstarrival Show maclock stations Output Details Set maclock enableSet maclock enable port‐string Set maclock Set maclock disableThis example shows how to enable MAC locking on ge.2.3 This example shows how to disable MAC locking on ge.2.3 Specified MAC address and port Clear maclockCreate Clear maclock static Set maclock static Set maclock firstarrival Set maclock agefirstarrival Clear maclock firstarrival Set maclock move This example enables first arrival aging on port ge.1.1This example disables first arrival aging on port ge.1.1 Clear maclock agefirstarrival Set maclock trap About PWA Configuring Port Web Authentication PWA Show pwa Output Details Show pwa Set pwa Enable disable Enables or disables port web authenticationThis example shows how to enable port web authentication Set pwa banner This example shows how to display the PWA login bannerShow pwa banner Display hide This example shows how to hide the Enterasys Networks logoClear pwa banner Set pwa displaylogo Chap pap Set pwa ipaddressSet pwa protocol Clear pwa guestname Use this command to clear the PWA guest user nameThis example shows how to clear the PWA guest user name Set pwa guestname Authradius Set pwa guestpasswordSet pwa gueststatus Authnone Set pwa quietperiod This example shows how to initialize ports ge.1.5‐7Set pwa initialize Set pwa portcontrol Set pwa maxrequest Show pwa session Enables or disables PWA on specified portsThis example shows how to enable PWA on ports 1‐22 This example shows how to display PWA session information Set pwa enhancedmode Enable disable Enables or disables PWA enhancedmodeThis example shows how to enable PWA enhancedmode Set ssh Configuring Secure Shell SSHThis example shows how to display SSH status on the switch Show ssh status Set ssh hostkey This example shows how to disable SSHThis example shows how to regenerate SSH keys Show access‐lists number Configuring Access ListsShow access-lists Deny permit Access-list standard This example moves entry 16 to the beginning of ACL Access-list extendedInsert replace Insert replace Filters inbound frames Ip access-groupInterface configuration C3su‐routerConfig‐ifVlan vlanid# Example Page TACACS+ Configuration Show tacacs Output Details Show tacacsState Optional Displays only the TACACS+ client status Set tacacs Use this command to enable or disable the TACACS+ clientEnable disable Enables or disables the Tacacs client This example shows how to enable the TACACS+ client Set tacacs server Timeout seconds Specifies one TACACS+ server to be affected Clear tacacs server This example removes TACACS+ server Show tacacs session Set tacacs session Super‐user ServiceClear tacacs session Read‐write Set tacacs command Show tacacs command Connection Show tacacs singleconnectSet tacacs singleconnect Set tacacs interface Show tacacs interface Clear tacacs interface Clear tacacs interface TACACS+ Configuration 27-14 Advantages of using sFlow include SFlow ConfigurationUsing sFlow in Your Network SFlow Definitions DefinitionsSFlow Agent Functionality Sampling Mechanisms Usage Notes Packet Flow SamplingCounter Sampling 28-5 This example displays the sFlow Receivers Table Contents of the sFlow Receivers Table is displayedShow sflow receivers Show sflow receivers Output Descriptions Following table describes the output fields Set sflow receiver ip Set sflow receiver owner Maxdatagram bytes Default IP address isDefault maximum datagram size is 1400 bytes Set sflow receiver maxdatagram Maxdatagram Default port value isSet sflow receiver port Clear sflow receiver Port port Set sflow port pollerOwner Show sflow pollers This example removes the poller instance on port ge.1.1 Clear sflow port pollerSet sflow port sampler Interval Show sflow samplers Rate Clear sflow port samplerSet sflow interface Maxheadersize Show sflow interface Clear sflow interface Show sflow agent 28-18 Table A-1 Policy Capacities Policy and Authentication CapacitiesPolicy Capacities Table A-2 Authentication Capacities Authentication Capacities Numerics Index Ospf 20-30Network Management Tftp Index

Parameters

status

disable

enable

vvid

dot1p

untagged

trusted

yes

cos value

port‐string

Defaults

Usage