Manuals / Enterasys Networks / Computer Equipment / Switch

Enterasys Networks 9034313-07 manual Show logging buffer, Show logging interface

Models: 9034313-07

1 872

Download 872 pages 24.54 Kb

Page 425

Image 425

show logging buffer

Example

This example shows how to clear local logging:

C3(su)->clear logging local

show logging buffer

Use this command to display the last 256 messages logged. By default, critical failures and user login and logout timestamps are displayed.

Syntax

show logging buffer

Parameters

None.

Defaults

None.

Mode

Switch command, read‐only.

Example

This example shows a portion of the information displayed with the show logging buffer command:

C3(su)->show logging buffer

<165>Sep 4 07:43:09 10.42.71.13 CLI[5]User:rw logged in from 10.2.1.122 (telnet) <165>Sep 4 07:43:24 10.42.71.13 CLI[5]User: debug failed login from 10.4.1.100 (telnet)

show logging interface

Use this command to display the interface used for the source IP address of the system logging.

Syntax

show logging interface

Parameters

None.

Defaults

None.

Mode

Switch mode, read‐only.

SecureStack C3 Configuration Guide 14-11

Page 425

Image 425

Enterasys Networks 9034313-07 Show logging buffer, Show logging interface, This example shows how to clear local logging

Contents

Enterasys SecureStack C3 Page Page Enterasys Networks, Inc. Firmware License Agreement Iii Page Contents Page Activating Licensed Features Discovery Protocol Configuration Configuring System Power and PoEPort Configuration Show port broadcast Set port broadcast Clear port broadcast Snmp Configuration Spanning Tree Configuration Configuring Spanning Tree Port Parameters Purpose Commands 802.1Q Vlan Configuration Port Priority Configuration Policy Classification ConfigurationLogging and Network Management Igmp Configuration14-3 Rmon Configuration Dhcp Server Configuration Dhcp Snooping and Dynamic ARP Inspection Preparing for Router ModeIP Configuration IPv4 Routing Protocol Configuration 20-11 IPv6 Management IPv6 ConfigurationIPv6 Proxy Routing DHCPv6 ConfigurationOSPFv3 Configuration Authentication and Authorization Configuration 26-37 TACACS+ Configuration Appendix a Policy and Authentication Capacities SFlow ConfigurationIndex Tables10-4 22-26 Xxxii About This Guide Using This GuideStructure of This Guide Important NoticeStructure of This Guide Related Documents SecureStack C3 Installation GuidesFollowing icons are used in this guide Conventions Used in This GuideFollowing conventions are used in the text of this document Support@enterasys.com Getting HelpGetting Help Xxxviii About This Guide SecureStack C3 CLI Overview Switch Management MethodsIntroduction Default Settings for Basic Switch Operation Factory Default SettingsFeature Default Setting Sntp Default Settings for Router OperationDvmrp Starting a CLI Session Using the Command Line InterfaceConnecting Using the Console Port Using a Default User Account Connecting Using TelnetUsing an Administratively Configured User Account LoggingCLI Command Defaults Descriptions Navigating the Command Line InterfaceCLI Command Modes Getting Help with CLI SyntaxDisplaying Scrolling Screens Abbreviating and Completing CommandsBasic Line Editing Commands Basic Line Editing CommandsAbout SecureStack C3 Switch Operation in a Stack Configuring Switches in a StackInstalling a New Stackable System of Up to Eight Units Adding a New Unit to an Existing Stack Installing Previously-Configured Systems in a StackCreating a Virtual Switch Configuration SID Issues Related to Mixed Type Stacks Considerations About Using Clear Config in a StackFeature Support ConfigurationShow switch Stacking Configuration and Management CommandsCommands PurposeExamples Show switch switchtypeNone Show switch stack-portsSwitch command, read‐write Set switchExample Priority valueSet switch description Set switch copy-fwThis example shows how to assign priority 3 to switch This example shows how to renumber switch 5 to switchSet switch member Set switch movemanagementUse this command to remove a member entry from the stack Clear switch memberRequired CLI Setup Commands Basic ConfigurationQuick Start Setup Commands Optional CLI Setup Commands Setting User Accounts and PasswordsParameters Show system loginShow system login Output Details Clear system login Set system loginUse this command to remove a local login user account Super‐user read‐write read‐onlySwitch command, read‐write Switch command, super‐user Set passwordThis example shows how to remove the netops user account Set system password aging Set system password lengthShow system lockout Set system password historyDisable Show system lockout Output Details Set system lockoutAttempts attempts Time timeSetting Basic Switch Properties Show ip address Clear ip address Use this command to clear the system IP addressSet ip address Set ip protocol This example shows how to clear the system IP addressShow ip protocol Show system This example shows how to display system informationShow system Output Details Show system hardwareSlot Hardware Information Show system utilizationThis example sets the CPU utilization threshold to 75% Default threshold value is 80%Set system utilization Show system enhancedbuffermode Clear system utilizationEnable disable Enables or disables enhanced buffer mode Set system temperatureThis example shows how to enable enhanced buffer mode Set system enhancedbuffermodeSyslog enable Clear system temperatureDisable Trap enable disableSet time Show timeShow summertime This example shows how to set the system clock to 750 a.mUse this command to display daylight savings time settings Set summertime date Set summertimeIf a zone name is not specified, none will be applied If an offset is not specified, none will be appliedSet summertime recurring This example shows how to set the command prompt to Switch Use this command to modify the command promptClear summertime Set promptSet banner motd Show banner motdShow version Clear banner motdUse this command to configure a name for the system ‐5 provides an explanation of the command outputSet system name Show version Output DetailsThis example shows how to set the system location string Use this command to identify the location of the systemSet system location Set system contactThis example shows how to set the terminal columns to This example shows how to set the system contact stringSet width Set lengthThis example shows how to display the CLI logout setting This example shows how to set the terminal length toShow logout Set logoutThis example shows how to display all console settings Use this command to display console settingsUse this command to set the console port baud rate Show consoleDownloading a Firmware Image This example shows how to set the console port baud rate toDownloading from a Tftp Server Downloading via the Serial PortType 2. The following baud rate selection screen displays Reverting to a Previous Image Reboot the system using the reset command page 3‐50 Reviewing and Selecting a Boot Firmware ImageShow boot system Compatibility platform specific Set boot systemThis example shows how to display Telnet status Starting and Configuring TelnetUse this command to enable or disable Telnet on the switch Show telnetTelnet Enable disableInbound Outbound allConfiguration Persistence Mode Managing Switch Configuration and FilesSet snmp persistmode Show snmp persistmodeDir Save configAuto ManualShow file Use this command to display the contents of a fileShow config Outfile ConfigureAll Systemimage CopyAppend Delete Show tftp settingsThis example shows how to download an image via Tftp Clear tftp timeout Set tftp timeoutThis example shows the output of this command This example sets the timeout period to 4 secondsThis example sets the retry count to Set tftp retryClear tftp retry Clearing and Closing the CLI This example shows how to clear the CLI screenCls clear screen To clear the CLI screen or to close your CLI sessionReset Resetting the SwitchUse either of these commands to leave a CLI session This example shows how to exit a CLI sessionIf no unit ID is specified, the entire system will be reset Clear configThis example shows how to reset the system This example shows how to reset unitShow webview Using and Configuring WebViewUse this command to display WebView status Show ssl Set webviewSet ssl This example shows how to display SSL statusThis example shows how to enable SSL Gathering Technical Support Information CommandShow support To gather common technical support informationHostprotect is enabled by default Configuring HostprotectShow system hostprotect Set system hostprotectThis example disables hostprotect This feature is disabled by defaultDefault state is enabled Clear system hostprotectUsage License Key Field Descriptions Activating Licensed FeaturesLicensing Procedure in a Stack Environment Adding a New Member to a Licensed Stack Clearing, Showing, and Applying LicensesUsage Set licenseFeatureID feature The name of the feature being cleared Use this command to clear the license key settingsShow license Clear licenseC3rw-clear license featureId advrouter Clear license Activating Licensed Features Commands Configuring System Power and PoEShow inlinepower Use this command to display system power propertiesShow inlinepower Output Details Set inlinepower thresholdThis example shows how to display system power properties Sending of traps is disabled by default Set inlinepower trapSet inlinepower detectionmode Ieee Show port inlinepowerAdmin off auto Set port inlinepowerPriority critical High lowSet port inlinepower Configuring System Power and PoE Configuring CDP Discovery Protocol ConfigurationShow cdp Output Details Show cdpSet cdp state Auto disableEnable Set cdp interval Use this command to set a global CDP authentication codeSet cdp auth Clear cdp Set cdp hold-timeShow neighbors Show ciscodp Configuring Cisco Discovery Protocol‐3 provides an explanation of the command output ‐2 provides an explanation of the command outputShow ciscodp port info Show ciscodp Output DetailsThis example shows how to globally enable CiscoDP Set ciscodp timerSet ciscodp status Show ciscodp port info Output DetailsSet ciscodp port Set ciscodp holdtimeDot1p VvidUntagged TrustedClear ciscodp Overview Configuring Link Layer Discovery Protocol and LLDP-MEDTo review and configure Llpd and LLPD‐MED Configuration Tasks Show lldp Use this command to display Lldp configuration informationShow lldp port trap Show lldp port statusShow lldp port tx‐tlv port‐string Show lldp port tx-tlvShow lldp port location-info Show lldp port local-info 1000BASE-TFD Show lldp port local-info Output DetailsECS Elin Show lldp port remote-info Guest‐voice‐signaling Voice‐signalingShow lldp port network-policy VoiceSet lldp tx-interval Video‐signalingSoftphone‐voice Video‐conferencingThis example sets the transmit interval to 20 seconds Set lldp hold-multiplierSet lldp trap-interval Set lldp med-fast-repeat Rx‐enable Tx‐enableSet lldp port status Set lldp port trapElin Set lldp port med-trapSet lldp port location-info Set lldp port tx-tlv Mac‐phy GvrpPoe Link‐aggrSet lldp port network-policy State enable disableTag tagged untagged Vid vlan‐id dot1pTx‐interval Clear lldpHold‐multiplier Trap‐intervalClear lldp port trap Clear lldp port statusCleared Clear lldp port med-trapClear lldp port location-info Tag Clear lldp port network-policyVid DscpClear lldp port tx-tlv Disables the LLDP‐MED Extended Power via MDI TLV from being Disables the LLDP‐MED Location Identification TLV from beingPort Configuration Summary Port ConfigurationPort String Syntax Used in the CLI Port type.unitorslot number.port numberPort Slot/Unit Parameters Used in the CLI Reviewing Port StatusShow port status Show portShow port status Output Details Switch mib2Show port counters Show port counters Output Details This example clears the port counters for ge.3.1 Clear port countersShow port cablestatus Show port cablestatus Output Details Disabling / Enabling and Naming PortsThis example shows the cable status for 1 GE port ge.1.31 Set port enable Set port disableThis example shows how to disable ge.1.1 This example shows how to enable ge.1.3Set port alias Use this command to assign an alias name to a portShow port alias This example shows how to clear the alias for ge.3.3 This example shows how to assign the alias Admin to ge.3.3Show port speed Setting Speed and Duplex ModeShow port duplex Set port speed10 100 MbpsFull half This example shows how to set ge.1.17 to full duplexSet port duplex Show port jumbo Enabling / Disabling Jumbo Frame SupportClear port jumbo Enables or disables jumbo frame supportSet port jumbo Show port negotiation Setting Auto-Negotiation and Advertised AbilityShow port advertise Enable disableSet port negotiation Set port advertise Clear port advertise Set port mdix Show port mdixForced‐auto MdiOptional Specify the port or ports to configure Configure ports to use MDI mode onlyConfigure ports to use Mdix mode only Set flowcontrol Setting Flow ControlShow flowcontrol This example shows how to enable flow control Show port trap Setting Port Link Traps and Link Flap DetectionShow linkflap Following example disables sending trap on ge.3.1Set port trap Portstate GlobalstateParameters MetricsShow linkflap metrics Output Details Show linkflap parameters Output DetailsDisables or enables the link flap detection function Disable enableSet linkflap globalstate Set linkflap portstateSet linkflap action Set linkflap intervalSet linkflap threshold Use this command to set the link flap action trigger countClear linkflap action Clear linkflap down Set linkflap downtimeAll stats Clear linkflapParameter Threshold intervalShow port broadcast Configuring Broadcast SuppressionClear port broadcast Set port broadcastSyntax Used in the CLI on page 7‐1 Remote Port Mirroring Mirroring FeaturesPort Mirroring Overview Configuring Smon MIB Port MirroringProcedures Show port mirroring To review and configure port mirroring on the deviceSet port mirroring Create disableCan be configured per stack, if applicable Set mirror vlan Use this command to clear a port mirroring relationshipClear port mirroring Clear mirror vlan Lacp Operation Link Aggregation Control Protocol LacpLacp Terminology ‐6 defines key terminology used in Lacp configurationSecureStack C3 Usage Considerations Lacp Terms and DefinitionsCommands Show lacp ‐7 provides an explanation of the command outputThis example shows how to disable Lacp Disable enable Disables or enables LacpSet lacp Show lacp Output DetailsAsyspri Set lacp aadminkeySet lacp asyspri Set lacp static Disable enable Disables or enables static link aggregationClear lacp Clear lacp static Clear lacp singleportlag This example enables the formation of single port LAGsSet lacp singleportlag Summary Counters Show port lacpStatus detail Set port lacp AadminkeyLacptimeout AadminstatePadminkey PadminportClear port lacp C3su-clear port lacp port ge.3.16 Protected Port Operation Configuring Protected PortsSet port protected Read‐only Show port protectedClear port protected Show port protected name Set port protected nameClear port protected name Use this command to clear the name of a protected groupClear port protected name Port Configuration Snmp Configuration Summary Snmp ConfigurationAbout Snmp Security Models and Levels SNMPv1 and SNMPv2cSNMPv3 Configuration Considerations Using Snmp Contexts to Access Specific MIBsReviewing Snmp Statistics Snmp Security LevelsShow snmp engineid Output Details This example shows how to display Snmp engine propertiesShow snmp engineid Show snmp counters Use this command to display Snmp traffic counter valuesThis example shows how to display Snmp counter values Show snmp counters Output Details Engine or otherwise unavailable Show snmp user Configuring Snmp Users, Groups, and Communities‐4 provides an explanation of the command output This example shows how to display an Snmp user listUse this command to create a new SNMPv3 user Set snmp userSha AesVolatile NonvolatileRemote remote Clear snmp userShow snmp group User user Set snmp groupSecurity‐model V2c usm VolatileV2c usm Clear snmp groupShow snmp community Set snmp community Use this command to configure an Snmp community groupSecurityname Context contextUse this command to delete an Snmp community name Configuring Snmp Access RightsThis example shows how to delete the community name vip Clear snmp communityNoauthentication Show snmp accessAuthentication Privacy Context context Nonvolatile read‐ OnlyShow snmp access Output Details This example shows how to display Snmp access information‐6 provides an explanation of the command output Set snmp access Configuring Snmp MIB Views Clear snmp accessShow snmp view Show snmp view Output Details Show snmp contextSet snmp view Clear snmp view Show snmp targetparams Configuring Snmp Target ParametersVolatile nonvolatile Read‐onlySet snmp targetparams ‐8 provides an explanation of the command outputShow snmp targetparams Output Details Message‐Clear snmp targetparams AuthenticationPrivacy Protected from disclosureShow snmp targetaddr Configuring Snmp Target AddressesUse this command to display Snmp target address information Set snmp targetaddr Timeout timeoutParam param Udpport udpportClear snmp targetaddr Use this command to delete an Snmp target address entryTaglist taglist Tag 1 tagAbout Snmp Notify Filters Configuring Snmp Notification ParametersSet newaddrtrap By default, this function is disabled globally and per portShow newaddrtrap Show snmp notify Set snmp notify ‐10 provides an explanation of the command output10 show snmp notify Output Details Trap informShow snmp notifyfilter Use this command to clear an Snmp notify configurationClear snmp notify Subtree oid‐or‐ Set snmp notifyfilterClear snmp notifyfilter Targetparam Show snmp notifyprofileSet snmp notifyprofile Clear snmp notifyprofile Creating a Basic Snmp Trap ConfigurationThis example shows how to delete Snmp notify profile area51 Example 11 Basic Snmp Trap ConfigurationShow snmp interface Configuring the Snmp Management InterfaceHow Snmp Will Use This Configuration Loopback loop‐ID Set snmp interfaceClear snmp interface Clear snmp interface Snmp Configuration Spanning Tree Configuration Summary Spanning Tree ConfigurationLoop Protect Spanning Tree FeaturesConfiguring Spanning Tree Bridge Parameters For information about Active Show spantree statsSid sid Show spantree Output Details ‐1 shows a detailed explanation of command outputShow spantree version Disable enable Globally disables or enables Spanning TreeSet spantree Set spantree version Show spantree bpdu-forwarding This example shows how to reset the Spanning Tree versionClear spantree version By default Bpdu forwarding is disabled Disable enable Disables or enables Bpdu forwardingThis example shows how to enable Bpdu forwarding Set spantree bpdu-forwardingClear spantree bridgeprioritymode Set spantree bridgeprioritymode8021d 8021tCreate delete Show spantree mstilistSet spantree msti Fid fid Clear spantree mstiShow spantree mstmap Use this command to map a FID back to SID This example shows how to map FID 3 to SIDSet spantree mstmap Clear spantree mstmapShow spantree mstcfgid This example shows how to map FID 2 back to SIDShow spantree vlanlist Clear spantree mstcfgid Cfgname name Specifies an MST configuration nameSet spantree mstcfgid Clear spantree priority Use this command to set the device’s Spanning Tree prioritySet spantree priority Clear spantree hello This example shows how to reset the bridge priority on SIDSet spantree hello Set spantree maxage Use this command to set the bridge maximum aging timeClear spantree maxage Set spantree fwddelayUse this command to set the Spanning Tree forward delay Show spantree backuproot Clear spantree fwddelayClear spantree backuproot Set spantree backuprootSet spantree tctrapsuppress Show spantree tctrapsuppressSet spantree protomigration Clear spantree tctrapsuppressSet spantree spanguard Enable disable Enables or disables the SpanGuard functionShow spantree spanguard Clear spantree spanguard This example shows how to enable the SpanGuard functionSet spantree spanguardtimeout Show spantree spanguardtimeoutShow spantree spanguardlock Clear spantree spanguardtimeoutClear / set spantree spanguardlock Show spantree spanguardtrapenableThis example shows how to unlock port ge.1.16 Is enabled Set spantree spanguardtrapenableClear spantree spanguardtrapenable Set spantree legacypathcost Show spantree legacypathcostShow spantree autoedge Clear spantree legacypathcostSet spantree autoedge This example clears the legacy path cost to 802.1t valuesClear spantree autoedge Set spantree portadmin Configuring Spanning Tree Port ParametersDisable enable To display and set Spanning Tree port parametersThis example shows how to disable Spanning Tree on ge.1.5 Clear spantree portadminShow spantree portadmin Set spantree portpri Use this command to set a port’s Spanning Tree priorityShow spantree portpri Clear spantree portpri Set spantree adminpathcost Show spantree adminpathcostShow spantree adminedge Clear spantree adminpathcostClear spantree adminedge Set spantree adminedgeThis example shows how to set ge.1.11 as an edge port True falseShow spantree operedge This example shows how to reset ge.1.11 as a non‐edge portConfiguring Spanning Tree Loop Protect Parameters Set spantree lp This example shows how to enable Loop Protect on ge.2.3Show spantree lp If no SID is specified, SID 0 is assumedShow spantree lplock Clear spantree lpSID Locked Clear spantree lplockShow spantree lpcapablepartner Set spantree lpcapablepartnerSet spantree lpthreshold Use this command to set the Loop Protect event thresholdClear spantree lpcapablepartner Clear spantree lpthreshold None. The default event threshold isShow spantree lpthreshold Show spantree lpwindow Set spantree lpwindowClear spantree lpwindow Set spantree lptrapenableDisabled Clear spantree lptrapenable Show spantree lptrapenableSet spantree disputedbpduthreshold Clear spantree disputedbpduthreshold Show spantree disputedbpduthresholdShow spantree nonforwardingreason Vlan Configuration Summary 802.1Q Vlan ConfigurationCreating a Secure Management Vlan Command Set for Creating a Secure Management VlanShow vlan Viewing VLANsStatic PortinfoVlan Vlan ID Name Show vlan Output DetailsThis example shows how to create Vlan Create enable Creates, enables or disables VLANs. disableCreating and Naming Static VLANs Set vlanClear vlan This example shows how to set the name for Vlan 7 to greenSet vlan name Clear vlan name This example shows how to clear the name for VlanShow port vlan Assigning Port Vlan IDs PVIDs and Ingress FilteringClear port vlan Set port vlanModify‐egress No‐modify‐egressShow port ingress filter Show port discard Set port ingress filterTagged untagged both none Set port discardShow port egress Configuring the Vlan Egress ListSet vlan forbidden Set vlan egress Use this command to remove ports from a VLAN’s egress listClear vlan egress Untagged forbidden taggedForbidden Show vlan dynamicegressSet vlan dynamicegress Enable disable Enables or disables dynamic egressThis example shows how to enable dynamic egress on Vlan Set host vlan Setting the Host VlanShow host vlan Clear host vlan This example shows how to set Vlan 7 as the host VlanHow It Works Enabling/Disabling Gvrp Garp Vlan Registration ProtocolAbout Garp Vlan Registration Protocol Gvrp Example of Vlan Propagation via Gvrp Show gvrp Show garp timerUse this command to display Gvrp configuration information Set gvrp Show gvrp configuration Output DetailsDisables or enables Gvrp on the device Clear gvrp Set garp timerThis example shows how to enable Gvrp on ge.1.3 Leaveall timer‐ Clear garp timerJoin LeaveC3su-clear garp timer leave ge.1.1 Policy Classification Configuration Summary Policy Classification ConfigurationUse this command to display policy profile information Configuring Policy ProfilesShow policy profile ‐verboseShow policy profile Output Details Set policy profile Clear policy profile Use this command to delete a policy profile entryThis example shows how to delete policy profile Show policy rule Configuring Classification RulesAll admin‐ profile profile‐ index Admin‐pid Not‐in‐service Not‐ready Storage‐type non‐Tcpsourceport UdpdestportShow policy rule Output Details Show policy capabilityVlan Vlantag data Admin‐profileSet policy rule Ipproto EtherIpdestsocket IpsourcesocketData value Mask bits Valid Values for Policy Classification RulesClear policy rule Following parameters apply to deleting an admin ruleRange from 1 to 4094 or 0xFFF All‐pid‐entriesClear policy all-rules Use this command to remove all policy classification rulesAssigning Ports to Policy Profiles Use this command to assign ports to a policy profileSet policy port To assign and unassign ports to policy profilesClear policy port Procedure 11-1 User-Defined CoS Configuration Configuring Policy Class of Service CoSAbout Policy-Based CoS Configurations Configuring Policy Class of Service CoS About CoS-Based Flood Control ProcedureSet cos state Use this command to enable or disable Class of ServiceClear cos state This example shows how to enable Class of ServiceShow cos state Priority priority Set cos settingsTos‐value tos‐value Irl‐referenceShow cos settings Clear cos settingsPriority Tos‐valueSet cos port-config Should be displayed Show cos port-configEntry Clear cos port-configName PortsSet cos port-resource irl Group#.port‐type Set cos port-resource flood-ctrlUnicast MulticastGroup#.port‐type Show cos port-resourceUnit Clear cos port-resource irlRate TypeSet cos reference Clear cos port-resource flood-ctrlUnicast MulticastShow cos reference Specifies that an IRL reference is being configuredIRL reference number associated with this entry Rate‐limit irl‐indexClear cos reference Port‐typ e index Show cos unitKbps PpsShow cos port-type Clear cos all-entriesThis example shows flood control information for port type Port Priority Configuration Summary Port Priority ConfigurationShow port priority Configuring Port PriorityClear port priority Set port priorityShow port priority-queue Configuring Priority to Transmit Queue MappingSet port priority-queue Clear port priority-queue Show port txq Configuring Quality of Service QoSSet port txq Clear port txq By default, transmit queues are defined as followsClear port txq Port Priority Configuration About IP Multicast Group Management Igmp ConfigurationIgmp Overview About Multicasting Configuring Igmp at LayerTo configure Igmp snooping from the switch CLI Use this command to display Igmp snooping information Set igmpsnooping adminmodeThis example shows how to display Igmp snooping information Use this command to enable or disable Igmp on the systemEnable disable Enables or disables Igmp This example shows how to enable Igmp on the systemThis example shows how to enable Igmp on port ge.1.10 Set igmpsnooping interfacemodeSet igmpsnooping maxresponse Set igmpsnooping add-static Set igmpsnooping mcrtrexpiretimeModify If no ports are specified, all ports are added to the entryIf modify is not specified, a new entry is created Set igmpsnooping remove-staticShow igmpsnooping static Group group Show igmpsnooping mfdbThis example displays the static Igmp ports for Vlan Stats Optional Displays Mfdb statisticsClear igmpsnooping Use this command to clear all Igmp snooping entriesThis example shows how to clear all Igmp snooping entries To configure Igmp on routing interfaces Configuring Igmp on Routing InterfacesGlobal configuration C3su‐routerConfig# Ip igmpThis example shows how to enable Igmp on the router Ip igmp enableInterface configuration C3su‐routerConfig‐ifVlan 1# Ip igmp versionShow ip igmp interface Any router modeIp igmp query-interval Show ip igmp groupsIp igmp startup-query-interval Ip igmp query-max-response-timeIp igmp last-member-query-interval Ip igmp startup-query-countIp igmp robustness Ip igmp last-member-query-countInterface configuration C3 su‐routerConfig‐ifVlan 1# Ip igmp robustness Igmp Configuration Logging and Network Management Configuring System LoggingShow logging server Set logging server Clear logging server Show logging defaultUse this command to set logging default values Set logging defaultShow logging application Clear logging defaultFacility SeverityShow logging application Output Details Set logging applicationIf level is not specified, none will be applied Level levelShow logging local Clear logging applicationClear logging local Set logging localShow logging interface This example shows how to clear local loggingShow logging buffer Set logging interface Clear logging interface History Monitoring Network Events and StatusDefault Use this command to set the size of the history bufferShow history Set historyThis example, the host at IP address is not responding PingShow users Console DisconnectShow netstat Show netstat Output Details Following example shows the output of this commandFollowing table describes the output of this command Show arp Managing Switch Network Addresses and RoutesUse this command to display the switch’s ARP table Show arp Output Details This example shows how to display the ARP tableSet arp Traceroute Clear arpEach response Show macType other learned Self mgmtShow mac Output Details Show mac agetimeThis example shows how to set the MAC timeout period This example shows how to display the MAC timeout periodSet mac agetime Clear mac agetimeShow mac algorithm Default MAC algorithm is mac‐crc16‐upperbitsSet mac algorithm Set mac multicast Clear mac algorithmAppend clear Use this command to remove a multicast MAC addressClear mac address Set mac unreserved-flood Show mac unreserved-floodThis example enables multicast flood protection Configuring Simple Network Time Protocol SntpUse this command to display Sntp client settings Show sntpShow sntp Output Details This example shows how to display Sntp client settingsClear sntp client Set sntp clientIf precedence is not specified, 1 will be applied Set sntp serverClear sntp server Clear sntp poll-interval Set sntp poll-intervalClear sntp poll-retry This example shows how to clear the Sntp poll intervalSet sntp poll-retry Clear sntp poll-timeout Set sntp poll-timeoutUse this command to clear the Sntp poll timeout This example shows how to clear the Sntp poll timeoutSet timezone Set sntp interface Show sntp interfaceClear sntp interface C3rw-show sntp interface Vlan 100 C3rw-clear sntp interface Show nodealias config Configuring Node AliasesMaxentries maxentries Show nodealias config Output DetailsSet nodealias Clear nodealias config Rmon Monitoring Group Functions Rmon ConfigurationRmon Monitoring Group Functions and Commands Design Considerations Group What It Does What It Monitors CLI CommandsTo display, configure, and clear Rmon statistics Statistics Group CommandsSet rmon stats Use this command to configure an Rmon statistics entryShow rmon stats This example shows how to delete Rmon statistics entry To‐defaultsClear rmon stats If owner is not specified, monitor will be appliedShow rmon history History Group CommandsClear rmon history Set rmon historyBuckets buckets Interval intervalThis example shows how to delete Rmon history entry This example shows how to display Rmon alarm entry Alarm Group CommandsShow rmon alarm Show rmon alarm Output Details Set rmon alarm propertiesObject object Type absoluteSet rmon alarm status Enable Clear rmon alarmThis example shows how to enable Rmon alarm entry Use this command to delete an Rmon alarm entryUse this command to display Rmon event entry properties Event Group CommandsThis example shows how to display Rmon event entry Show rmon eventDescription Set rmon event propertiesType none log Trap bothClear rmon event This example shows how to enable Rmon event entrySet rmon event status This example shows how to clear Rmon event Show rmon channel Filter Group CommandsSet rmon channel Use this command to configure an Rmon channel entryAccept matched FailedShow rmon filter Clear rmon channelIndex index Channel channelSet rmon filter Clear rmon filter Use this command to clear an Rmon filter entryThis example shows how to clear Rmon filter entry Nodata Packet Capture CommandsShow rmon capture Action lock Set rmon captureSlice slice Loadsize loadsizeClear rmon capture Use this command to clears an Rmon capture entryThis example shows how to clear Rmon capture entry Dhcp Overview Dhcp Server ConfigurationDhcp Relay Agent Dhcp ServerConfiguring a Dhcp Server Configuring General Dhcp Server Parameters Set dhcp Set dhcp bootpThis example enables Dhcp server functionality This example enables Dhcp conflict logging This example enables address allocation for Bootp clientsSet dhcp conflict logging Show dhcp conflictThis example disables Dhcp conflict logging Logging Disables conflict loggingClear dhcp conflict Clears the conflict information for all IP addressesClear dhcp exclude 100, with the set dhcp exclude commandSet dhcp exclude This example sets the number of ping packets sent to Set dhcp pingClear dhcp ping Clear dhcp binding Show dhcp bindingUse this command to clear all Dhcp server counters Use this command to display Dhcp server statisticsShow dhcp server statistics Clear dhcp server statisticsThis example clears all Dhcp server counters Manual Pool Configuration Considerations Configuring IP Address PoolsThis example creates an address pool named auto1 Set dhcp poolClear dhcp pool Use this command to delete a Dhcp server pool of addressesSet dhcp pool network This example deletes the address pool named auto1Set dhcp pool hardware-address Clear dhcp pool networkIf no type is specified, Ethernet is assumed Clear dhcp pool hardware-addressSet dhcp pool host Set dhcp pool client-identifier Clear dhcp pool hostClear dhcp pool client-identifier Clear dhcp pool client-name Set dhcp pool client-nameClear dhcp pool bootfile Set dhcp pool bootfileClear dhcp pool next-server Set dhcp pool next-serverInfinite Set dhcp pool leaseClear dhcp pool lease Clear dhcp pool default-router Set dhcp pool default-routerClear dhcp pool dns-server Set dhcp pool dns-serverClear dhcp pool domain-name Set dhcp pool domain-nameClear dhcp pool netbios-name-server Set dhcp pool netbios-name-server‐node Set dhcp pool netbios-node-typeClear dhcp pool netbios-node-type Ascii string Set dhcp pool optionThis example removes option 19 from address pool auto1 Show dhcp pool configurationClear dhcp pool option Show dhcp pool configuration Dhcp Message Processing Dhcp Snooping Dynamic ARP InspectionDhcp Snooping Overview Building and Maintaining the Database Configuration Notes Basic ConfigurationProcedure 17-1 Basic Configuration for Dhcp Snooping Rate LimitingSet dhcpsnooping Dhcp Snooping CommandsDisabled globally Set dhcpsnooping vlan Set dhcpsnooping database write-delaySet dhcpsnooping trust By default, ports are untrustedSet dhcpsnooping verify This example configures port ge.1.1 as a trusted portSet dhcpsnooping binding Against the client hardware address Source MAC address verification is enabled by defaultSet dhcpsnooping log-invalid None Set dhcpsnooping limitRate pps Burst interval secsThis example configures rate limit parameters on port ge.1.1 Show dhcpsnooping port Show dhcpsnooping databaseEntry, either dynamic or static Show dhcpsnooping bindingDynamic static Show dhcpsnooping statistics Clear dhcpsnooping database Clear dhcpsnooping bindingClear dhcpsnooping statistics Default value of 300 seconds Write‐delayClear dhcpsnooping limit Dynamic ARP Inspection OverviewOptional ARP Packet Validation Functional DescriptionStatic Mappings Packet Forwarding Logging Invalid PacketsRate Limiting Eligible InterfacesStep Task Commands Procedure 17-2 Basic Dynamic ARP Inspection ConfigurationVlan Configuration Example ConfigurationRouter Configuration Set arpinspection vlan Dynamic ARP Inspection CommandsDhcp Snooping Configuration Dynamic ARP Inspection ConfigurationLogging is disabled by default Set arpinspection trustBy default, all physical ports and LAGs are untrusted LoggingDst‐mac Set arpinspection validateSrc‐mac Set arpinspection limit Show arpinspection access-list Set arpinspection filterPermit Mac hostThis example displays the ARP configuration of lag.0.1 Show arpinspection portsShow arpinspection statistics Show arpinspection vlanThis example removes all 3 additional validation conditions Clear arpinspection validateWith an invalid address Clear arpinspection vlan Clear arpinspection filter This example removes the ARP ACL named staticARP from Vlan Clear arpinspection limitThis example clears all DAI statistics from the switch Clear arpinspection statisticsPage Pre-Routing Configuration Tasks Preparing for Router ModeRouter CLI Configuration Modes Enabling Router Configuration ModesEnabling the Switch for Routing Router CLI Configuration Modes Page Configuring Routing Interface Settings IP ConfigurationVlan vlan ‐id Show interfaceRouter global configuration mode C3su‐routerConfig# Use this command to configure interfaces for IP routingInterface Vlan vlan‐ idShow ip interface This example shows how to enter configuration mode for VlanIp address Router interface configuration C3su‐routerConfig‐ifVlan 1#Show ip interface Output Details SecondaryNo shutdown Show running-configNo ip routing This example shows how to enable Vlan 1 for IP routingInterface tunnel Configuring Tunnel InterfacesUse this command to configure a tunnel interface Tunnel source This example creates a configured tunnel interfaceRouter interface configuration C3su‐routerConfig‐ifTnnl 1# This command specifies the mode of the tunnel interface Tunnel modeIpv6ip Specifies that the tunnel mode is IPv6 over IPv4 No form of this command removes the mode of the tunnelShow interface tunnel This example sets the tunnel mode to IPv6 over IPv4Show ip arp Reviewing and Configuring the ARP TableShow ip arp Output Details This example shows how to use the show ip arp commandArp Ip proxy-arp This example shows how to enable proxy ARP on VlanClear arp-cache Arp timeout14,400 seconds Privileged Exec C3su‐router#Ip directed-broadcast Configuring Broadcast SettingsInterface configuration C3su‐Router1Config‐ifVlan 1# Udp Ip forward-protocolSpecifies UDP as the IP forwarding protocol Are forwardedIp helper-address Show ip route Reviewing IP Traffic and Configuring RoutesOSPF, IA Preference in route selection Ip routePing Traceroute This command is also available in switch modeThere is also a traceroute command available in switch mode Ip icmp redirect enable Configuring Icmp RedirectsInterface Show ip icmp redirectActivating Advanced Routing Features IPv4 Routing Protocol ConfigurationRIP Configuration Task List and Commands Configuring RIPRIP Configuration Task List and Commands Router ripDistance Ip rip enableThis example shows how to enable RIP R1compatible Ip rip send versionSpecifies RIP version 1. This is the default setting Ip rip authentication-keyIp rip receive version Specifies RIP versionMd5 Ip rip message-digest-keyRouter configuration C3su‐routerConfig‐router# Use this command to disable automatic route summarizationNo auto-summary Split-horizon poisonPassive-interface Redistribute Receive-interfaceConnected OspfProtocol Command detailed in ip route on page 19‐21Subnets Subnetted will be redistributedOspf Configuration Task List and Commands Configuring OspfOspf Configuration Task List and Commands Advanced License RequiredRoutes Router id1583compatibility This example shows how to enable routing for Ospf processRouter ospf Ip ospf areaid Ip ospf enableThis example shows how to enable RFC 1583 compatibility Ip ospf priority Ip ospf costTimers spf Ip ospf retransmit-interval Ip ospf transmit-delay65535 Ip ospf hello-intervalIp ospf dead-interval Ip ospf authentication-key Distance ospf Ip ospf message digest key md5External inter‐ Area rangeArea intra‐area Intra‐area routesArea stub If not specified, advertise mode will be setAdvertise no‐ AdvertiseArea nssa Area default costThis example shows how to configure area 10 as an Nssa area Default‐Area virtual-link Information‐Transmit‐delay Authentication‐Key key Dead‐intervalMetric‐type type Show ip ospfRip Show ip ospf database This example shows how to display Ospf informationUse this command to display the Ospf link state database Show ip ospf database Output Details Show ip ospf interfaceShow ip ospf interface Output Details Show ip ospf neighbor Output Details Show ip ospf neighborShow ip ospf virtual links Output Details Show ip ospf virtual-linksClear ip ospf process This example shows how to reset Ospf process Enabling Dvmrp on an Interface Configuring DvmrpCommands to Enable Dvmrp on an Interface Ip dvmrp enableThis example shows how to enable the Dvmrp process Ip dvmrpShow ip dvmrp Use this command to display Dvmrp routing informationIp dvmrp metric This example shows how to display Dvmrp status information Ip irdp enable Configuring IrdpIp irdp minadvertinterval Ip irdp maxadvertinterval9000 Ip irdp holdtimeIp irdp preference Show ip irdp Use this command to display Irdp informationIp irdp broadcast Configuration Tasks on page 18‐1 Router vrrp Configuring VrrpCreate This example shows how enable Vrrp configuration modeAddress Advertise-interval PriorityPreempt Described in Pre‐Routing Configuration Tasks on page 18‐1Enable Use this command to display Vrrp routing information Ip vrrp authentication-keyThis example shows how to display Vrrp information Show ip vrrpDesign Considerations Configuring PIM-SMThis example shows how to globally enable and disable PIM Global router configuration C3su‐routerConfig#Ip pimsm Ip pimsm staticrpIp pimsm enable Show ip pimsm This example shows how to display PIM informationIp pimsm query-interval Show ip pimsm Output Details This example shows how to display PIM router informationShow ip pimsm componenttable Show ip pimsm interface This example shows how to display PIM interface informationShow ip pimsm componenettable Output Details StatsShow ip pimsm neighbor This example shows how to display PIM interface statisticsShow ip pimsm interface vlan Output Details 10 show ip pimsm interface stats Output DetailsShow ip pimsm rp ‐11 provides an explanation of the command output11 show ip pimsm neighbor Output Details Candidate12 show ip pimsm rp Output Details ‐12 provides an explanation of the command outputShow ip pimsm rphash Display the PIM‐SM static Rendezvous Point information ‐13 provides an explanation of the command outputShow ip pimsm staticrp 13 show ip pimsm staticrp Output Details Use this command to display the IP multicast routing tableShow ip mroute 20-60 IPv4 Routing Protocol Configuration Show ipv6 status IPv6 ManagementSet ipv6 By default, IPv6 management is disabledThis example shows how to enable IPv6 management Eui64 No global unicast IPv6 address is defined by defaultSet ipv6 address Clear ipv6 address Use this command to clear IPv6 global addressesShow ipv6 address Set ipv6 gateway Show ipv6 neighbors Use this command to clear an IPv6 gateway addressClear ipv6 gateway Show ipv6 netstat This example shows example output of this commandUse this command to display IPv6 netstat information Size num This command is also available in router modePing ipv6 Traceroute ipv6 Traceroute ipv6 21-10 IPv6 Management IPv6 Routing License Required IPv6 ConfigurationOverview Following table lists the default IPv6 conditions Default ConditionsIpv6 hop-limit General Configuration CommandsIpv6 forwarding This command configures static IPv6 routes Default maximum number of IPv6 hops isIpv6 route This example sets the hop limit toIpv6 route distance Default preference or administrative distance isIpv6 unicast-routing This command sets the default distance value toLink‐local‐address Ping ipv6 interfaceRouter privileged exec C3 su‐router# 20010db8123455551 No IPv6 addresses are defined for any interface Interface Configuration CommandsIpv6 address IPv6 is disabled Ipv6 enableBytes Ipv6 mtuThis example sets the MTU value to 1500 bytes This example clears all dynamically learned cache entries Neighbor Cache and Neighbor Discovery CommandsClear ipv6 neighbors Ipv6 nd ns-interval Duplicate address detection enabled, for 1 attemptIpv6 nd dad attempts Router interface configurationC3su‐routerConfig‐ifVlan 1# By default, a value of 0 is advertised in RA messagesIpv6 nd reachable-time This example sets the NS interval to 2 secondsFlag is set to false by default Ipv6 nd other-config-flagRouter interface configuration C3su‐routerConfig‐if Vlan 1# This example sets the reachable time to 60 secondsIpv6 nd ra-lifetime Ipv6 nd ra-intervalThis example disables router advertisement transmission Suppression disabledIpv6 nd suppress-ra Ipv6 nd prefixOff‐link No‐autoconfigRouter interface configurationC3su‐routerConfig‐if Vlan 1# Example Show ipv6 Query CommandsShow ipv6 interface Router privileged execution C3su‐router#This example displays information about IPv6 interface Vlan This example displays the neighbors in the cache This command displays IPv6 Neighbor Cache informationShow ipv6 route This command displays the IPv6 routing tableShow ipv6 neighbor Output Details Interface interfaceShow ipv6 route Output Details This example displays all active IPv6 routesShow ipv6 route preferences Output Details Show ipv6 route preferencesNon‐best routes This command displays the summary of the routing tableShow ipv6 route summary Show ipv6 summary Output Details Following example displays the output of this commandShow ipv6 traffic Show ipv6 traffic Output Details Options, etc Counter would include datagrams counted Send. Note that this counter includes all those counted by This example clears the statistics for Vlan Clear ipv6 statisticsRouter privileged executionC3su‐router# IPv6 Proxy Routing Limitations Preparing a Mixed Stack for IPv6 Proxy RoutingRouter global configuration C2su‐routerConfig# IPv6 proxy routing is disabled by defaultThis example enables IPv6 proxy routing Ipv6 proxy-routingAny routing mode DHCPv6 Configuration Ipv6 dhcp enable Global Configuration CommandsFollowing table lists the default DHCPv6 conditions This command enables DHCPv6 on the routerIpv6 dhcp relay-agent-info-opt By default, DHCPv6 is disabledThis example enables DHCPv6 Ipv6 dhcp pool Ipv6 dhcp relay-agent-info-remote-id-suboptIpv6 dhcp pool Domain-name Address Pool Configuration CommandsPrefix-delegation Dns-serverSecs infinite Valid‐lifetime secsPreferred‐lifetime C3su-routerConfig-dhcp6s-pool# exit C3su-routerConfig# Ipv6 dhcp server By default, DHCPv6 functionality is disabledRapid‐commit Preference prefDestination dest‐addr Ipv6 dhcp relayInterface intf Remote‐id duid‐ifidExamples Show ipv6 dhcp DHCPv6 Show CommandsStatistics Show ipv6 dhcp interfaceThis example displays the DHCPv6 statistics for Vlan Output of show ipv6 dhcp interface CommandShow ipv6 dhcp statistics This example displays the output of this commandOutput of show ipv6 dhcp statistics Command This example clears DHCPv6 statistics for Vlan Clear ipv6 dhcp statisticsShow ipv6 dhcp binding This command displays information about DHCPv6 bindingsShow ipv6 dhcp pool If no IPv6 address is specified, all bindings are displayed Show ipv6 dhcp binding DHCPv6 Configuration OSPFv3 Configuration Following table lists the default OSPFv3 conditions Ipv6 router id Global OSPFv3 Configuration CommandsUse this command to configure the OSPFv3 router ID Ipv6 router ospf Default-information originateAlways Metric valueRouter OSPFv3 configuration C3su‐routerConfig‐router# Default-metricNo default metric is configured Router OSPFv3 configuration C3su-routerConfig-router#Intra Exit-overflow-intervalInter Type1Default value is ‐1 This command configures the external Lsdb limit for OSPFv3External-lsdb-limit This example sets the exit overflow interval to 10 secondsTag tag Maximum-pathsConnected static Metric = unspecified Metric type = Type Tag = These commands are used to configure area parameters Area Configuration CommandsArea default-cost This example shows how to configure area 20 as an Nssa This example sets the default route cost to 50 for areaDefault metric value is Area nssa default-info-originateArea nssa no-redistribute ComparableArea nssa no-summary By default, the translator role is disabled This command configures the translator role of the routerArea nssa translator role Area nssa translator-stab-intvArea address ranges are not configured by default Default interval is 40 secondsSummarylink NssaexternallinkThis command creates a stub area for the specified area ID This example creates a stub area with the ID Example disables the import of summary LSAs into stub areaArea stub no-summary Area virtual-link dead-interval Default dead interval is 40 secondsArea virtual-link retransmit-interval Default hello interval is 10 secondsArea virtual-link hello-interval Default transmit delay is 1 second Area virtual-link transmit-delayDefault retransmit interval is 5 seconds OSPFv3 is disabled by default Ipv6 ospf enableIpv6 ospf cost Ipv6 ospf areaidIpv6 ospf dead-interval Default dead interval value is 40 secondsIpv6 ospf mtu-ignore Ipv6 ospf hello-intervalIpv6 ospf network By default, MTU mismatch detection is enabledDefault network type is broadcast Ipv6 ospf retransmit-interval Default priority value isIpv6 ospf priority Default value is 1 second Ipv6 ospf transmit-delayDefault value is 4 seconds Ipv6 ospf transmit-delay This command displays OSPFv3 router information OSPFv3 Show CommandsThis example shows how to display OSPFv3 router information Show ipv6 ospfShow ipv6 ospf Output Details Show ipv6 ospf area Output Details Show ipv6 ospf areaShow ipv6 ospf abr Output Details Show ipv6 ospf abrShow ipv6 ospf asbr Output Details Show ipv6 ospf asbrShow ipv6 ospf database Adv Router Link Id Age Sequence Csum Options Rtr Opt Show ipv6 ospf database Output Details Show ipv6 ospf database database-summary Output Details Loopback loopid This command displays information about OSPFv3 interfacesShow ipv6 ospf interface Show ipv6 ospf interface Command Output Details Show ipv6 ospf interface stats This example shows how to display statistics for VlanShow ipv6 ospf interface stats Output Details Show ipv6 ospf neighbor This command displays information about OSPFv3 neighborsSpecify the Vlan interface to display information about Specify the tunnel interface to displayShow ipv6 ospf neighbor Output Details This example displays range information for area Show ipv6 ospf range10 show ipv6 ospf neighbor routerid Output Details 11 show ipv6 ospf range Output Details Show ipv6 ospf stub tableThis example displays the OSPFv3 stub table information 12 show ipv6 ospf stub table Output Details13 show ipv6 ospf virtual-link Output Details Show ipv6 ospf virtual-linkShow ipv6 ospf virtual-link Show ipv6 ospf virtual-link OSPFv3 Configuration Overview of Authentication and Authorization Methods Authentication and Authorization ConfigurationOverview of Authentication and Authorization Methods Filter-ID Attribute Formats Show authentication login Setting the Authentication Login MethodSet authentication login Use this command to set the authentication login methodAny Clear authentication loginLocal RadiusTimeout Configuring RadiusShow radius RetriesSet radius Optional Displays Radius server configuration informationServer Servers or a specific Radius server as defined by an indexServer index Timeout timeoutRealm management‐ access any network‐access Realm Clear radiusRetries retries Show radius accountingSet radius accounting Timeout This example shows how to set Radius accounting retries toClear radius accounting RetriesSet radius interface Show radius interfaceClear radius interface Example Show dot1x Configuring 802.1X AuthenticationAuth‐diag Auth‐statsThis example shows how to display 802.1X status Show dot1x auth-config True false Set dot1xInit reauth Set dot1x auth-config Portcontrol Maxreq Clear dot1x auth-configShow eapol Show eapol Output Details Connecting state, via disconnectedClear eapol Set eapolAuth‐mode Forced‐authOptional Globally clears the Eapol authentication mode Show macauthentication Configuring MAC AuthenticationNopassword Show macauthentication Output DetailsShow macauthentication session Output Details Show macauthentication sessionThis example shows how to display MAC session information Use this command to set a MAC authentication password Set macauthenticationSet macauthentication password Set macauthentication port Clear macauthentication passwordUse this command to clear the MAC authentication password Enables or disables MAC authenticationSet macauthentication portquietperiod Set macauthentication portinitializeThis example resets the default quiet period on port Clear macauthentication portquietperiodSet macauthentication macinitialize Enables or disables MAC reauthentication Set macauthentication reauthenticationSet macauthentication portreauthenticate Set macauthentication reauthperiod Set macauthentication macreauthenticateClear macauthentication reauthperiod Clear macauthentication significant-bits Set macauthentication significant-bitsC3su-clear macauthentication significant-bits About Multi-User Authentication Configuring Multiple Authentication MethodsAbout Multiple Authentication Types Show multiauth Clear multiauth mode Set multiauth modeMulti StrictClear multiauth precedence Default precedence order is dot1x, pwa, macSet multiauth precedence Set multiauth port Show multiauth portClear multiauth port Show multiauth session Show multiauth stationAgent dot1x mac Show multiauth idle-timeoutAuthentication method for which to set the timeout value Set multiauth idle-timeoutWhich to set the timeout value Idle timeout value is provided by the authenticating serverShow multiauth session-timeout Clear multiauth idle-timeoutDefault Which to reset the timeout value to its defaultWhich to set the session timeout value Set multiauth session-timeoutConfiguring User + IP Phone Authentication Clear multiauth session-timeoutConfiguring Vlan Authorization RFC Tagged Set vlanauthorizationSet vlanauthorization egress By default, administrative egress is set to untagged Clear vlanauthorizationShow vlanauthorization Show vlanauthorization Output Details Configuring Policy Maptable ResponseOperational Description When Policy Maptable Response is BothShow policy maptable When Policy Maptable Response is PolicyWhen Policy Maptable Response is Tunnel Response Set policy maptableBoth PolicyClear policy maptable To review, disable, enable, and configure MAC locking Configuring MAC LockingShow maclock Show maclock Output Details Show maclock stationsFirstarrival Connected to MAC locked portsShow maclock stations Output Details Set maclock enableSet maclock enable port‐string This example shows how to enable MAC locking on ge.2.3 Set maclock disableThis example shows how to disable MAC locking on ge.2.3 Set maclockSpecified MAC address and port Clear maclockCreate Clear maclock static Set maclock staticSet maclock firstarrival Set maclock agefirstarrival Clear maclock firstarrivalThis example disables first arrival aging on port ge.1.1 This example enables first arrival aging on port ge.1.1Clear maclock agefirstarrival Set maclock moveSet maclock trap About PWA Configuring Port Web Authentication PWAShow pwa Output Details Show pwaSet pwa Enable disable Enables or disables port web authenticationThis example shows how to enable port web authentication Set pwa banner This example shows how to display the PWA login bannerShow pwa banner Clear pwa banner This example shows how to hide the Enterasys Networks logoSet pwa displaylogo Display hideChap pap Set pwa ipaddressSet pwa protocol This example shows how to clear the PWA guest user name Use this command to clear the PWA guest user nameSet pwa guestname Clear pwa guestnameSet pwa gueststatus Set pwa guestpasswordAuthnone AuthradiusSet pwa quietperiod This example shows how to initialize ports ge.1.5‐7Set pwa initialize Set pwa portcontrol Set pwa maxrequestThis example shows how to enable PWA on ports 1‐22 Enables or disables PWA on specified portsThis example shows how to display PWA session information Show pwa sessionSet pwa enhancedmode Enable disable Enables or disables PWA enhancedmodeThis example shows how to enable PWA enhancedmode This example shows how to display SSH status on the switch Configuring Secure Shell SSHShow ssh status Set sshSet ssh hostkey This example shows how to disable SSHThis example shows how to regenerate SSH keys Show access‐lists number Configuring Access ListsShow access-lists Deny permit Access-list standardThis example moves entry 16 to the beginning of ACL Access-list extendedInsert replace Insert replace Filters inbound frames Ip access-groupInterface configuration C3su‐routerConfig‐ifVlan vlanid# Example Page TACACS+ Configuration Show tacacs Output Details Show tacacsState Optional Displays only the TACACS+ client status Enable disable Enables or disables the Tacacs client Use this command to enable or disable the TACACS+ clientThis example shows how to enable the TACACS+ client Set tacacsSet tacacs server Timeout secondsSpecifies one TACACS+ server to be affected Clear tacacs serverThis example removes TACACS+ server Show tacacs sessionSet tacacs session Clear tacacs session ServiceRead‐write Super‐userSet tacacs command Show tacacs commandConnection Show tacacs singleconnectSet tacacs singleconnect Set tacacs interface Show tacacs interfaceClear tacacs interface Clear tacacs interface TACACS+ Configuration 27-14 Advantages of using sFlow include SFlow ConfigurationUsing sFlow in Your Network SFlow Agent Functionality DefinitionsSampling Mechanisms SFlow DefinitionsUsage Notes Packet Flow SamplingCounter Sampling 28-5 This example displays the sFlow Receivers Table Contents of the sFlow Receivers Table is displayedShow sflow receivers Show sflow receivers Output Descriptions Following table describes the output fieldsSet sflow receiver ip Set sflow receiver ownerDefault maximum datagram size is 1400 bytes Default IP address isSet sflow receiver maxdatagram Maxdatagram bytesSet sflow receiver port Default port value isClear sflow receiver MaxdatagramPort port Set sflow port pollerOwner Show sflow pollers Set sflow port sampler Clear sflow port pollerInterval This example removes the poller instance on port ge.1.1Show sflow samplers Set sflow interface Clear sflow port samplerMaxheadersize RateShow sflow interface Clear sflow interface Show sflow agent 28-18 Table A-1 Policy Capacities Policy and Authentication CapacitiesPolicy Capacities Table A-2 Authentication Capacities Authentication CapacitiesNumerics IndexOspf 20-30Network Management Tftp Index