ADCP-70-220 Issue 1 September 2000 Section 1 Introduction

To access any node in the network, the administrator selects the direct selection arrow tool located on the left tool bar, and then double clicks on the NE ICON to open a shelf level GUI session. To start a craft session with the node, the user selects the node with a single click, right click to open the pop-up menu, and select Craft Interface. The administrator is required to enter a valid user name and password assigned for the node to gain access to the craft menus. The shelf level GUI is shown in Figure 1-7 below.

CHASSIS STATUS

CHASSIS CONFIGURATION

 

Cellworx Vision:

Chassis View,

Network Element 2

 

 

 

 

X

File

Configuration

Fault

 

Security

 

 

 

 

 

 

 

 

 

 

S

N

 

 

 

T

T

T

T

T

 

E

E

 

 

 

2

2

S

C

M

 

 

 

3

M

1

3

3

 

1

1

 

 

 

4

4

C

 

I

 

 

 

 

U

M

 

 

 

M

M

 

 

 

8

8

 

 

C

 

 

 

T

X

u

C

C

 

u

u

 

 

 

8

8

 

 

 

 

 

 

M

 

l

R

R

 

l

l

 

 

 

R

R

 

 

 

 

 

 

U

E

t

S

S

 

t

t

 

 

 

 

 

 

 

 

 

X

X

i

 

 

 

i

i

 

 

 

i

i

 

 

 

 

 

 

 

P

 

 

 

 

 

 

 

 

 

n

n

 

 

 

 

 

 

 

 

1

 

 

 

1

1

 

 

 

g

g

 

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

Status:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power Status: normal

 

 

 

 

 

Alarm Status:

minor

 

 

 

 

Identifier:

 

2

 

 

 

 

 

Version:

 

1.2.0.35

 

 

 

 

Start Time:

 

19:30:47 8/31/1999

 

 

 

Current Time:

10:12:09 09/01/1999

 

Vendor:

 

ADC-TSG

 

 

 

 

Up Time:

 

1d 19:41:22:00

 

 

Configuration:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Name:

Cellworx2

 

 

 

 

Memory Utilization Threshold:

 

 

 

Location:

5th Street

 

 

 

 

 

Suppress Zero Stats

 

 

 

 

 

Apply

 

 

Topology View

 

 

Refresh

 

 

 

 

Close

 

EQUIPPED CARD REPRESENTATIONS WITH ALARM INDICATIONS.

CLICK ON BOXES AND DRAG UP OR DOWN TO WIDEN STATUS, CONFIGURATION OR CHASSIS VIEW.

USE SLIDERS TO VIEW HIDDEN STATUSES OR SELECTIONS.

APPLIES CHANGES

RETURNS TO GUI MAIN

REPAINTS WINDOW

CLOSES CHASSIS LEVEL

 

AND SENDS TO SHELF

VIEW WITHOUT CLOSING

TO REFLECT ANY

VIEW AND RETURNS TO

 

CONTROLLER.

CHASSIS LEVEL VIEW.

CHANGES.

GUI MAIN VIEW.

13454-C

 

 

 

 

Figure 1-7. Cellworx Shelf Level GUI Screen

The user can now provision parameters on individual cards in the shelf. To bring up a card level GUI display, double click on the card displayed in the shelf level view or put the mouse pointer over the card and hit a right click to open a menu window for the card and select Open. The Card level view will appear similar to the example shown in Figure 1-8 below. Some functions available in this view are described in the figure.

Page 1-7

© 2000, ADC Telecommunications, Inc.

Page 24
Image 24
ADC Release 3.1 user manual Cellworx Shelf Level GUI Screen