NEC NDA-24298 manual Skn

2

3

The default characters are shown in the "Default display".

SKN

0-15

1

Note 2

Note 1

ADSL : Assignment of Dterm Soft Key on LCD

3. Data Entry Instructions

SKP

Assign arbitrary number within 0 through 15.

0=soft key pattern shared in a system

1-15=soft key pattern alloted to each station.

SN

0 = Idle

1 = Originating (DT connection)

2 = Originating (RBT connection)

3 = Called station busy (BT connection) Note 1

4 = Communication in progress (Converse)

5 = Consultation Hold (Controlling Station)

6 = Trunk busy (BT connection)

7 = Not used

8 = Consultation Hold when Called Station is Busy (Controlling Station)

9 = 3-Party Conference call

10-14 = Not used

15 = others

SKN

Soft key number (SKN) appears on the MAT.

DISP

The soft key indication is displayed when DISP has assigned by the AFDD command.

SOFT KEY PATTERN

(SKP) 0-15

1

STATUS NUMBER

(SN) 0-15

2

FUNCTION KEY DATA

(FKY) 1-320

26

DISP

FKY(1-320)Note:

FKY	Service name	Default display
1	Call Forwarding-Busy Line	FDB
2	Call Forwarding-All Calls	FDA
3	Executive Right of Way	E_OVR
4	Call Waiting	CW
5	Call Back	CB
6	-	-
7	Save and Repeat	S&R
8	-	-
9	Boss-Secretary-Message	MW SET
	Waiting Lamp Control; Set
10	Call Hold	C_HOLD
11	Boss-Secretary-Message	MWOFF
	Waiting Lamp Control; Cancel
12	Call Pickup-Group	PICK
13	Three-way Calling	CONF
14	Voice Call	VOICE
15	Speed Calling-System	S-SPD
16	-	-
17	CAS SHF	CAS
18	-	-
19	UCD Busy Out	UCDBO
20	-	-
21	Flash Button	FLASH
22	Call Forwarding-Don't Answer	FDN
23-25	-	-
26	Speed Calling-Station	G_SPD
27-47	-	-
48	Privacy Release	P-RLS
49	-	-
50	Do Not Disturb	DND
51	Microphone	MIC
52-54	-	-
55	PAGE	BPAGE
56	OFF/ON Hook for Headset
57-59	-	-
60	Manual Signaling Key	SIG
61-82	-	-
83	Retain Conference	CKEEP
84	Serial Call	SCALL

FKY	Service name	Default display
85	Internal Zone Paging	IZP
86	-	-
87	Wake Up Set	WUS
88	Wake Up Reset	WUR
89	Do Not Disturb Set	DDS
90	Do Not Disturb Reset	DDR
91	Room Cut Off Set	RCS
92	Room Cut Off Reset	RCR
93	Message Waiting Set	MWS
94	Message Waiting Reset	MWR
95	Check In	C/I
96	Check Out	C/O
97	Status	STS
98	Audit	AUD
99	Enter	ENT
100	Clear Enter	E
101	END	END
102-112	-	-
113	Call ID change display	IDCHG
114	-	-
115	Call pickup expand	GPICK
116	-	-
117	Ringer mute	RMUTE
118-119	-	-
120	Next page of soft keys	>>>
	(Scroll key)
121	Previous page of soft keys	<<<
	(Back Scroll key)
122	-	-
123	Off Hook Ringing	OHR
124	MUTE	MUTE
125	Head Set Note 1	HSET
126	PS Key	PS
127	Boss Move	B_MV
128	Call Block	IDRST
129	Call Trace	RPT
130	-	-
131	Disconnect	DISC
132~320	-	-

Note 1: When assigning the Head Set Key, enter the related data to all the Status Numbers (SN).

Note 1: Available only for the Station to which Busy Service is applied.

Note 2: Available for the software Release 9 or later.

CHAPTER 4 NDA-24298

Page 468

Issue 1