Commands by Subsystem 3

Table 44 :CHANnel<n> Commands Summary (continued)

Command

Query

Options and Query Returns

 

 

 

 

:CHANnel<n>:PROBe:STY

:CHANnel<n>:PROBe:STY

<signal type> ::= {DIFFerential

Pe <signal type> (see

Pe? (see page 155)

SINGle}

 

 

 

 

page 155)

 

<n> ::=

1-2

or

1-4 in

NR1 format

 

 

 

 

 

 

:CHANnel<n>:PROTectio

:CHANnel<n>:PROTectio

{NORM

TRIP}

 

 

n (see page 156)

n? (see page 156)

<n> ::=

1-2

or

1-4 in

NR1 format

 

 

 

 

 

:CHANnel<n>:RANGe

:CHANnel<n>:RANGe?

<range>

::=

Vertical full-scale

<range>[suffix] (see

(see page 157)

range value

in

NR3 format

page 157)

 

[suffix] ::= {V mV}

 

 

 

<n> ::=

1-2

or

1-4 in

NR1 format

 

 

 

 

 

:CHANnel<n>:SCALe

:CHANnel<n>:SCALe?

<scale>

::=

Vertical units per

<scale>[suffix] (see

(see page 158)

division value

in NR3

format

page 158)

 

[suffix] ::= {V mV}

 

 

 

<n> ::=

1-2

or

1-4 in

NR1 format

 

 

 

 

 

:CHANnel<n>:UNITs

:CHANnel<n>:UNITs?

<units>

::=

{VOLT AMPere}

<units> (see

(see page 159)

<n> ::=

1-2

or

1-4 in

NR1 format

page 159)

 

 

 

 

 

 

 

 

 

 

 

 

 

:CHANnel<n>:VERNier

:CHANnel<n>:VERNier?

{0 1}

 

 

 

 

{{0 OFF} {1

(see page 160)

<n> ::=

1-2

or

1-4 in

NR1 format

ON}} (see page 160)

 

 

 

 

 

 

 

 

 

 

 

 

 

Introduction to :CHANnel<n> Commands

N O T E

<n> ::= {1 2 3 4} for the four channel oscilloscope models <n> ::= {1 2} for the two channel oscilloscope models

The CHANnel<n> subsystem commands control an analog channel (vertical or Y- axis of the oscilloscope). Channels are independently programmable for all offset, probe, coupling, bandwidth limit, inversion, vernier, and range (scale) functions. The channel number (1, 2, 3, or 4) specified in the command selects the analog channel that is affected by the command.

A label command provides identifying annotations of up to 6 characters.

You can toggle the channel displays on and off with the :CHANnel<n>:DISPlay command as well as with the root level commands :VIEW and :BLANk.

The obsolete CHANnel subsystem is supported.

Reporting the Setup

Use :CHANnel1?, :CHANnel2?, :CHANnel3? or :CHANnel4? to query setup information for the CHANnel<n> subsystem.

Agilent InfiniiVision 5000 Series Oscilloscopes Programmer's Reference

143

Page 143
Image 143
Agilent Technologies 5000 Series manual Obsolete CHANnel subsystem is supported Reporting the Setup