Manuals / Carrier Access / Computer Equipment / Network Router

Carrier Access user manual Access Navigator Release August 18-141

Models: Access Navigator

1 704

Download 704 pages 57.28 Kb

Page 597

CLI Language Reference

CLI Command List

Message:

Settings for DS1 9:	CA DS1# 9
Circuit ID:	CA DS1# 9
Up/Down:	DOWN
Framing:	ESF
Line Coding:	B8ZS
Type:	DROP
Clock Source:	NORMAL
Line Build Out:	CSU ATTEN FOR -15dB
Loop Code Detection:	ON
Loop Back:	OFF
Line Termination ID:	0 (for switch DS1s only)
Remote Device MGMT:	CA IP 192.168.201.1
PPHONE Call Connection:	Enabled
FDL Type:	None
Send Code:	NONE		1 hour	1 day
Performance Thresholds:	15 min.		1 hour	1 day
unavailable seconds:	--------		-------	------
unavailable seconds:		0	0	0
severely errored seconds:		0	0	0
errored seconds:		0	0	0
sev. errored frame seconds:		0	0	0
degraded minutes:		0	0	0
linecode violations:		0	0	0

NOTE: The Performance Thresholds are threshold values, not error counts.

Description:

Item	Description

Circuit ID	Circuit identifier set by user for the DS1 number.

Up/Down	Link service status: UP, DOWN.

Framing	D4 (SF), ESF, SLC96 (S4).

Line Coding	AMI, B8ZS.

Type	DROP, GROOM, SWITCH. Switch type appears only with GR-
	303 option.

Clock Source	NORMAL, LOOP.

Line Build Out	DSX-1 equalization (ft.), CSU attenuation (dB).

Loop Code Detection	ON, OFF.

Loop Back	OFF, LINE, PAYLOAD.

Line Termination ID	Line termination identifier, 1 to 28, set by user (used by GR-303
	only.

Remote Device MGMT	NONE, CAFDL, CAIP <ipaddress>, DS1 <n>.

Access Navigator - Release 1.8

August 2003

18-141

Image 597

Carrier Access user manual Access Navigator Release August 18-141

Contents

Access Navigator Mailtech-support@carrieraccess.com Preface Preface ComplianceElectrostatic Discharge ESD Precautions Carrier Access Software License Agreement LicenseTitle and Risk Copyright WarrantyTerm DisclaimerJurisdiction and Venue Limitations of Warranty & Limitation of Remedies WarrantyFollow Electrostatic Discharge ESD Precautions on Warranty Product ReturnsTable of Contents Table of Contents Access Navigator / GR-303 + Data HostAccess Navigator / GR-303 Host with P-Phone Electrical Installation Physical Installation1xv 1xvi August Access Navigator Release Provision Access Navigator Provision DCS ServiceStart Management Session Provision Remote Access Bank Provision GR-303 ServiceProvision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via FDLDiagnostics & Troubleshooting Alarm Clearing1xxi Update Controller Card Software Maintenance ProceduresCLI Language Reference 1xxiv August Access Navigator Release 1xxv 1xxvi August Access Navigator Release EOC Interface Snmp Interface FDL InterfaceGlossary IndexChapter Introduction OverviewAccess Navigator Configurations Features and BenefitsSystem Architecture Access Navigator System ArchitectureCarrier Access Support Products Access BanksAdit Management Command Line InterfaceSnmp Valet and NetworkValet EMS Software Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Access Navigator / DCS Service ManagerSwitch Center Co-location Customer Premises Functions ServicesFacilities ManagementNetwork Quad T1 Framer Card Features Controller Card Features ConfigurationApplications SpecificationsInterfaces DCS OperationAlarms SignalingSystem Clocking Management InterfacesCompliance PowerEnvironmental PhysicalFCC Requirements Compliance RequirementsPart 15, Class a PartTelcordia Bellcore Requirements Service Order Codes SOCUL Requirements Facility Interface Codes FICOrdering Information CSA RequirementsPart Number Description Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data HostGR-303 Ethernet RS-232 Modem Voice GR-303 Services Lines Management Key System Access Navigator Data Host Architecture DCS ServicesIP DS0 Management Management ArchitectureFDL Management Access Navigator FDL Management ArchitectureGR-303 call support Applications Crossconnects GR-303 OperationDCS Signaling GR-303 SignalingCompliance Compliance Requirements Telcordia Bellcore Requirements Ordering Information Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-PhoneAccess Navigator / GR-303 with P-Phone Architecture Features and Benefits Voice Fax P-Phone Service Support Using Adit 600 Terminals Phone ServicesDCS Services Management Architecture FDL Management Configuration Applications Specifications GR-303 Signaling Standards Compliance Requirements Telcordia Bellcore Requirements Ordering Information Ordering Information Physical Installation Physical Installation Compliance and Safety RequirementsUnpacking and Inspection Tools and MaterialsInstallation Summary Precautions Tools and MaterialsHorizontal 19-Inch Rack Mount Attach Access Navigator to Equipment Rack Attach Mounting Brackets to Access NavigatorMounting Four per side Bracket Fasten brackets to Horizontal 23-Inch Rack Mount Assemble Mounting Brackets Installation in 23-inch Equipment Rack Inches minimum Vertical Rack Mount Using Crossbars Attach Access Navigator to Crossbars Install CrossbarsCrossbar Installation Inch Equipment Rack Vertical Wall Mount PrecautionsPrepare Plywood Ensure Adequate ClearanceAttach Access Navigator to Plywood Wall View Wire Tie Plywood Sheet Inches Minimum 12. Mounting Hole Pattern on Plywood 13. Wall Mount Bracket Installation Physical Installation Electrical Installation Electrical Installation Static-Sensitive Equipment Handling Procedures Tools and Materials Required Chassis Ground Connection Connect Ground Wire to Ground Lug Run Ground Wire to Access NavigatorAttach Ground Lug to Access Navigator DSX-1 Cable Connections Prepare DSX-1 Cables CAC Location of Rear Panel DS1 Connectors Connect DSX-1 Cables to Access NavigatorElectrical Installation Attaching Ferrite Bead RF Suppressors Attach Ferrite BeadsConnect DSX-1 Cables to Interface or Patch Panel Card Group DSX-1 Cable Pin Connections and Flying Wire ColorsElectrical Installation Information, Tools, and Materials RS-232 Management ConnectionRS-232 DTE-to-DCE Cable RS-232 DCE-to-DCE Modem Cable Connections Connect Shielded RS-232 Cable10. Attaching Ferrite Bead RF Suppressor Attach Ferrite Bead RF SuppressorPreconfigure Optional Modem Ethernet Management Connection Information and MaterialsMake Ethernet Cable Optional MDI Port Pins Signals Connect Ethernet Cable to Ethernet Hub Connect Ethernet Cable to Access NavigatorExternal Timing Source Bits Connection Connect Bits Cable Make Bits Cable OptionalAlarm Output Connections 15. Alarm Output Connector Wire Alarm Output ConnectorMaximum 18. Location of Rear Panel Alarm Output Connector Plug Output Alarm Connector into Access NavigatorAlarm Input Connections 19. Alarm Input Connector Wire Alarm Input ConnectorCable Shield 22. Location of Rear Panel Alarm Input Connector Plug Alarm Input Connector into Access NavigatorDC Power Connections Used Wire Power ConnectorsConnect Power Plugs to Access Navigator Verify WiringDress Cables and Wires Dress Cables and WiresVerification Summary Acceptance Test26. Location of Front Panel Power-On Status LEDs Apply Power and Verify OperationVerify DSX-1 Connections Verify Chassis Ground ConnectionVerify RS-232 Management Connection Verify Ethernet Management Connection Verify Ethernet Cable ConnectionSet clock1 bits set clock2 bits Verify Bits ConnectionController ’A’ Indicators Controller ’B’ Indicators Verify Alarm Output ConnectionsElectrical Installation 31. Location of Rear Panel Alarm Input Connector Verify Alarm Input ConnectionsExit Exit Management SessionInstall Redundant Controller Card Verify Software Compatibility 33. Location of Front Panel Cover Screws Remove Front Cover34. Location of Controller Cards Install Controller CardVerify Operation Switch controllerReplace Front Cover Install Additional Quad T1 Framer Cards 37. Location of Front Panel Cover Screws 38. Location of Quad T1 Framer Cards Install Quad T1 Framer CardEject Set ds1 n up Status equipmentSet ds1 n down 29-32 13-16 17-20 21-24 26-28Configure Management Interfaces Setup SummaryReplace Front Cover Start RS-232 Management Session Set Time Set DateSet IP Address and Subnet Mask Set System ID or Clli codeSet Gateway Address Exit Management Session Start Management Session Start Management Session Management RequirementsShow ds1 Command Line Interface ConventionsProcedure Summary RS-232 ManagementRS-232 Management Requirements Connect RS-232 Cable to Access Navigator Set Up Terminal ProgramObtain Information Start RS-232 Management Session Exit RS-232 Management Session Perform Management OperationsTelnet Management Requirements Telnet ManagementStart Telnet Management Session Start Telnet Program and Connect to Access NavigatorExit Telnet Management Session When Finished NetworkValet EMS and Valet Management Start Management Session Provision Access Navigator CLI Commands Descriptions Provision Access NavigatorBasic Provisioning Overview Basic Provisioning Quick GuideObtain Provisioning Information Verify System Equipment Configuration Show id Set System ID or Clli CodeSet Time Set DateShow date Show timeSet Ethernet Properties Set ethernet ip address none Set User and Password Security Set user Alice password DNVRCO1A201 Set Snmp PropertiesExample Set snmp nms 1 Provision DCS Service DCS Provisioning Overview Provision DCS ServiceProvisioning TR-08 Service with DCS Provisioning Isdn BRI ServiceProvisioning Voice Services for TR-08 Shelves B, C, and D Provisioning Conventional TR-08 Voice ServicesSpecial TR-08 Settings Provisioning Enhanced Voice and Data ServicesDCS Provisioning Quick Guide Card not installed Show ds1 all Verify Service StatusStatus ds1 n Set ds1 n down Set ds0 nch type voicedata Set Unused Circuits Out of ServiceSet System Clock Source CAC Provision Groom DS1 Circuits to NetworkExample Set ds1 10 loopdetect on Provision Drop DS1 Circuits to Subscribers Test Groom DS1 CircuitsSet ds1 20 framing esf Provision and Connect Isdn BRI 3DS0 Channels Provision and Connect Isdn PRI ChannelsProvision and Connect DS0s DS0 #10 Turn Up Service Test DS1 and DS0 CircuitsSet ds1 n up set ds0 nch up Test DS1 and DS0 Circuits Provision GR-303 Service GR-303 Provisioning Overview Provision GR-303 ServiceAccess Navigator GR-303 Services Provisioning P-Phone Service Provisioning TR-08 Service to Access Banks Provisioning TR-08 Service with GR-303 TranslationSignaling Translation TR-08 ConfigurationSpecial Pots Cards CRV NumberingSet ds0 41-24 crv 311-334 slc96 Set ds0 49-16 crvFraming and FDL Settings Access Bank I/TR-08 Switch SettingsSwitch Shelf Access Bank I/TR-08 Loopback Code Response GR-303 Provisioning Quick Guide Set DS0s in service Connect Isdn D channel to SwitchSet DS1s in service Isdn BRI 41 TDM channelsAccess Navigator Release August 10-11 10-12 Set ds1 n down set ds0 nch down Show switch Set System Switch TypeProvision Switch DS1s to Interface Group 10-16 Access Navigator Release August 10-17 Assign Primary and Secondary EOC Set tmc primary nchnone Assign Primary and Secondary TMCTest DS1 Circuits Provision Drop DS1 Circuits to Subscriber Set ds1 n framing d4esfslc96 Example Set ds1 Fdl none Fdl t1403 10-24 Provision Isdn BRI 41 TDM Service to Subscribers CRV Show isdn database Send switch provision request10-28 Access Navigator Release August 10-29 Provision DS0s to Subscribers Set ds0 nch type gr303 Assign Call Reference Values CRVs Example Set ds0 21-4 crv Test Circuits Provision Remote Access Bank Provision Remote Access Bank Remote Access Bank II Provisioning OverviewRequirements Pre-Provisioning and TestingAnalog Interfaces Crossconnect FeaturesCrossconnections Abii Valid Crossconnect AssignmentsFX Analog Interfaces FX Interfaces Support Analog Voice and Data ServicesFractional Interfaces Valid Interface AssignmentsInterface Type DS1 Type DS0 Type Voice Data GR-303 Remote Interfaces Remote Access Bank II Provisioning Quick Guide Remote Access Bank II Maintenance Quick Guide DS1 Card Installed Card not installed 11-12 Access Navigator Release August 11-13 Temporarily Disable Configuration Downloading Provision Drop DS1 to Remote Access Bank Set ds1 n remote device management cafdl Provision DS0s Set ds0 nch type voicedatagr303 Provision DS0 Crossconnects Example connect 2519-24 Create Fractional Interfaces if required Configure Remote RS-232 Interface if used Set baud rate with the following command Configure Remote T1 Drop Interface if used Set remote n t1drop lbo setting Set remote n t1drop linecode amib8zsSet remote n t1drop prm ansiatt Configure Remote V.35 Interface if used Set remote n v35 clkinv rxtxrxtxnone Connect Fractional Interface to Remote Interface Download Configuration to Remote Access BankVerify Downloaded Settings optional Call Status FX and Spots To Loop or Test Remote CircuitsProvision Remote Adit 600 via FDL Provision Remote Adit 600 via FDL Remote Adit 600 FDL Provisioning OverviewOn-Net Customer Location Premises FDL Management ConfigurationRemote Adit 600 FDL Provisioning Quick Guide Set Provision Remote Adit 600 via FDLVerify Equipment Configuration Access Navigator Release August 12-7 Status remote nall CA FDLInterface Provision Drop DS1s to Remote Adit Set ds1 n linecode amib8zs 12-12 Provision Drop DS0s Set ds0 nch up Example set ds0 101-24 up Set ds0 nch signal lsgsemProvision DS0 Crossconnects if required Crossconnect Examples Logon remote n Provision Remote Adit12-18 Provision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via IP DS0 Remote IP DS0 Provisioning OverviewCarrier Access IP DS0 Management Configuration IP DS0 Management ConfigurationRemote IP DS0 Provisioning Quick Guide Access Navigator CLI Commands DescriptionsRouter Setup Adit CLI Commands DescriptionsRouter Provisioning Quick Guide Verify status of management channelSet Device Name to Adit1 Select the PVC Management as DisabledRemote Adit IP DS0 Provisioning Quick Guide 13-8 Access Navigator Release August 13-9 13-10 Out of Service Provision Groom DS1s to Adit Router Set ds1 32 framing esf 13-14 Access Navigator Release August 13-15 Set ds1 n remote device management caip ipaddr pphone Set ds1 n framing d4esfSet DS1 identification Provision Groom DS0s to Adit Router Provision Drop DS0s to Remote Adit 13-20 Access Navigator Release August 13-21 13-22 Access Navigator Release August 13-23 13-24 Alarm Clearing Identify Alarm Clearing Procedure Alarm ClearingFacility Alarm System go to Clear Alarms FDL on CLI Critical Alarm Message and Trouble Clearing Procedure Clear Alarms FDLEvent Message Description Trouble Clearing Procedure Set alarms critical offSet ds1 n updown CLI Major Alarm Message and Trouble Clearing ProcedureCard Software on CLI Minor Alarm Message and Trouble Clearing ProcedureShow eoc Status eocShow tmc Status tmcEOC Critical Alarm Message and Trouble Clearing Procedure Clear Alarms EOCEOC Major Alarm Message and Trouble Clearing Procedure EOC Minor Alarm Message and Trouble Clearing Procedure Active 14-12 Switch EOC Warning Alarm Message and Trouble Clearing ProcedureClear Alarms Snmp Trap Message and Trouble Clearing ProcedureTrap Message Description Trouble Clearing Procedure Alarm Indicators Clear Alarms Status IndicatorsPower Status LEDs Power Status LEDsLED State Description Troubleshooting System, use the switch controller Status equipment command forActive/Standby Controller Status LEDs 10. Active/Standby Controller Status LEDsMajor Alarm Status LEDs Critical Alarm Status LEDs11. Critical Alarm Status LEDs 12. Major Alarm Status LEDsAlarm Cutoff ACO Status LED Minor Alarm Status LEDs13. Minor Alarm Status LEDs 14. Alarm Cutoff ACO Status LEDsSet ds1 up command DS1 Status LEDs15. DS1 Status LEDs 16. Ethernet Link Status LED Ethernet Link Status LED14-22 Diagnostics & Troubleshooting Alarms and Logs Diagnostics & TroubleshootingOperations Interface Alarm Testing Alarm ReportingAlarm and Status Indicators Syntax set alarms criticalmajorminor onoffFacility Alarm System Alarm Cutoff ACOAlarm Signaling Red, Yellow RAI, Blue AIS DS1 Failures Event LogSyntax log majorminoralertinfo Configuration Change Log TMC Log Bert LogSyntax clear bert log Syntax log tmc permanentIndicator Locations Alarm and Status IndicatorsRear Panel Ethernet Indicator Indicator Descriptions Indicator DescriptionsState Description GreenStatus and Performance Status ClockSyntax status clock Status DS0 Syntax status ds0 nchExample status ds0 Syntax status ds1 n Status DS1Field Description Example status ds1Syntax status ds1 all Status DS1 AllAccess Navigator Release August 15-15 Status DS1 Performance Syntax status ds1 n performanceExample status ds1 9 performance Status DS1 Performance History Syntax status ds1 n performance historyExample status ds1 9 performance history Syntax clear ds1 n performance Clear DS1 PerformanceSyntax status equipment Status EquipmentSyntax status ip Status IPSyntax status remote nall Status RemoteField Example status remote allStatus CRV GR-303 Status and PerformanceSyntax status crv range Example status crvStatus Isdn CRV Syntax status isdn crv rangeExample status isdn crv 15-24 Status TMC Status EOCSyntax status eoc Syntax status tmcOriginating Calls Blocked Calls Secondary Status TMC History Syntax status tmc allintervalExample status tmc all Clear Peak Call Count Clear Blocked Call CountClear Permanent Call Count Set CRV IdleDS1 Loopdetect Near-End LoopbacksDS1 FDL Protocol Syntax set ds1 n loopdetect onoffDS1 Payload Loopback DS1 Line LoopbackSyntax set ds1 n line loopdownloopup Syntax set ds1 n payload loopdownloopupFar-End Loopbacks DS1 CSU LoopupSyntax send ds1 n csu loopuploopdown Syntax send ds1 n line loopuploopdown DS1 Line LoopupSyntax send ds1 n network loopuploopdown DS1 Network LoopupSyntax send ds1 n niu loopuploopdown DS1 NIU LoopupSyntax send ds1 n payload loopuploopdown DS1 Payload LoopupRead Remote Loopback Access Bank II LoopbacksSend Remote Loopdown Syntax read remote n loopbackSend Remote RS232 TSI Equipment Loopup Send Remote RS232 Line LoopupSyntax send remote n rs232 line loopup Syntax send remote 9 rs232 tsi equipment loopupSend Remote Sdsl Payload Loopup Send Remote RS232 TSI Network LoopupSyntax send remote 9 rs232 tsi network loopup Syntax send remote n sdsl payload loopupSend Remote T1 TSI Loopup Send Remote T1 Payload LoopupSyntax send remote n t1 payload loopup Syntax send remote n t1 tsi loopupSend Remote T1 Drop Payload Loopup Send Remote T1 Drop Line LoopupSyntax send remote n t1drop line loopup Syntax send remote n t1drop payload loopupSend Remote V35 Line Loopup Syntax send remote n t1drop tsi loopupSyntax send remote n v35 line loopup Send Remote V35 TSI Network Loopup Send Remote V35 TSI Equipment LoopupSyntax send remote n v35 tsi equipment loopup Syntax send remote n v35 tsi network loopupSend DS1 Pattern Off Bit Patterns and Error TestsSend DS1 Line Pattern Syntax send ds1 n offSyntax send ds1 n line p2e11p2e15p2e23qrss Send DS1 Payload PatternAccess Navigator Payload Code Send DS1 Line Pattern with BER Test Example set ds1 9 line p2e15 test Syntax send ds1 n line p2e11p2e15p2e23qrss testFBE 26. Send DS1 Payload Pattern with BER Test Send DS1 Payload Pattern with BER TestExample send ds1 9 payload p2e15 test Test Example15-52 Other Maintenance Commands Load tftp config ipaddr file Show usersWhoami Show isdn database show crv database Technical SupportLet run for 2 or 3 minutes Trace tmc onTrace tmc off Trace eoc Trace eoc OffMaintenance Procedures Maintenance Procedures Repair and Return ProcedureOverview Replace Controller CardTools and Materials Required Verify Equipment Status Determine Which Replacement Procedure to UseProcedure Summary PrecautionsReplace Protected Controller Card Verify Compatibility Remove Front Cover Location of Controller Cards Replace Standby ControllerInstalling and Removing Controller Card Verify Operation and Compatibility Replace Other Controller Card Replace Unprotected Controller Card Controller B Active DS1 Card Installed Access Navigator Release August 16-15 Insert New Controller Access Navigator Release August 16-17 Remove Old Controller Replace Quad T1 Framer Card OverviewQF Card Slot DS1 Circuit Numbers Tools and Materials Required Temporarily Move Clock Sources if required Verify Equipment StatusSet clock1 ds1 n Set clock2 ds1 nLocation of Front Panel Cover Screws 10. Location of Quad T1 Framer Cards Replace Quad T1 Card11. Installing Quad T1 Framer Card Verify Operation 12. Location of Front DS-1 Status Indicators Show clock Restore Clock Sources if requiredInstall Simm on Controller Card Precautions Tools and Materials Required 16-30 Standby Controller ACTIVE/STANDBY indicator is off 14. Location of Front Panel Cover Screws 15. Location of Controller Cards Install SimmSimm Access Navigator Release August 16-35 16-36 Update Controller Card Software Update Controller Card Software Download ProceduresUpdate Software via Tftp Two Controllers Tftp RequirementsEvent Log 17-4 Information and Materials Required Install Optional Tftp Server SoftwareRequirement One Controller is in Standby Status equipment allVerify IP Connectivity Upload ConfigurationDownload Software Show ds0 Set ds0 321 up set ds0 321 downSet ds0 321 down set ds0 321 up Example load tftp config 192.168.118.65 AN26 Download ConfigurationXmodem Requirements Update Software via Xmodem Two Controllers17-12 Access Navigator Release August 17-13 System Access Navigator Release August 17-15 17-16 Update Software via Xmodem One Controller 17-18 SW Build Number 17701 Boot Code Revision 01.09 Minutes Access Navigator Release August 17-21 17-22 CLI Language Reference CLI Language Reference CLI Access Via RS-232 and TelnetCLI Requirements Port settingsCLI over RS-232 Terminal emulationCLI over Telnet Access Navigator IP addressRS-232 interface for modem connection Ethernet interfaceUsing CLI Command Scripts Character and Line DelaysConfirmations and Errors Commands, Confirmations, and Error Messages Command CategoriesCLI Conventions and Shortcuts SystemID set ds1 24 framing esfText Conventions SystemID set ds1 42 framing esfSet ds1 1-4 up Command Syntax Descriptions Command Shortcuts Tabbing Entering DS1 and DS0 Numbers and RangesKeyboard Shortcuts Displaying Basic Commands Online HelpHelp System Overview Context Sensitive Help 18-12 Syntax print help Printing the Help FileAdministration Users and PasswordsAccess Levels User Level AccessWho Am Managing UsersShow Users Syntax show usersSet User Access Level Add UserSyntax add user name Example add user alice Delete User Password Set User PasswordAccess Definition Delete UserLogin with No User Name Required Logging In and OutStartup Message Login with User Name Required Login with No Password RequiredLogin with Password Required Logout Exit Autoexit CLI Session TimeoutSyntax set autoexit minutes Example set autoexitACO CLI Command ListCLI Language Reference Add Interface ACOType Description Remote Port Maximum Number of DS0sAlarms Syntax alarms majorminoralertSyntax add user name Syntax alarms ds1 nall majorminoralert Syntax alarms ds1 nallSyntax alarms equipment Syntax alarms equipment majorminoralertClear Bert Log Clear Config LogClear Blocked Call Count Clear DS1 PerformanceClear Peak Call Count Clear LogClear Permanent Call Count Clear Remote LogExample connect 2519-24 Connect18-30 Drop Groom Switch Connect Remote InterfaceDrop Syntax connect remote name fxrs232sdslt1dropv35 Delete InterfaceSyntax delete interface name Example delete interface AcmeV35Syntax delete user name DisconnectSyntax disconnect nch Example disconnectExit Disconnect RemoteExit Remote Session Ctrl+C Syntax disconnect remote nameXmodem LoadActive Load Tftp Config Log Example load tftp config 192.168.118.65 AN26Example log equipment minor Example log MessageLog Bert Example log config ds0 Log ConfigDescription Example log configExample log tmc Message Log TMCLogon Remote Syntax logon remote nExample logon remote Syntax read remote n alarms Read Remote AlarmsExample read remote 9 alarms Ping18-46 Access Navigator Release August 18-47 Read Remote Connections Syntax read remote n connectionsExample read remote 9 connections Access Navigator Release August 18-49 Read Remote Log Syntax read remote n logExample read remote 9 log Read Remote RS232 Read Remote LoopbackExample read remote 9 loopback Syntax read remote n rs232Syntax read remote n t1t1drop performance Read Remote PerformanceAccess Navigator Release August 18-53 Syntax read remote n t1 Read Remote T1Level 3 monitor Read Remote T1dropRead remote Read remote T1dropRead Remote Syntax read remote nExample read remote 9 Reset DS1 Framer Reset AllSyntax reset all Syntax reset ds1 nReset Standby Reset RemoteSyntax reset remote n Example reset remoteDefault Settings Restore DefaultsSyntax restore defaults Parameter Default CommentsNormal CLI Language Reference Line loopback deactivate Send DS1 CSU LoopupSend DS1 Line Loopup Example send ds1 9 csu loopupExample send ds1 9 csu loopdown 00001110 11111111 Send DS1 Line pattern Example send ds1 9 line loopupExample send ds1 9 line loopdown Send DS1 Line Pattern Example set ds1 9 line p2e15 Send DS1 Line pattern TestSend DS1 Line Pattern with BER Test Access Navigator Release August 18-69 Send DS1 Network Loopup Send DS1 Network LoopupSend DS1 NIU Loopup Example send ds1 9 network loopupExample send ds1 9 network loopdown Example send ds1 9 niu loopup Syntax send ds1 n niu loopup loopdownExample send ds1 9 niu loopdown Send DS1 Payload LoopupExample send ds1 9 payload loopdown Example send ds1 9 payload loopupSend DS1 Payload pattern 10. Send DS1 Payload Pattern Example send ds1 9 payload p2e15 Send DS1 Payload pattern Test11. Send DS1 Payload Pattern with BER Test P2e11 Example set ds1 9 payload p2e15 testExample send ds1 9 payload f1in8 test Send Remote Loopdown Send DS1 OffExample send ds1 9 off Example send remote 9 loopdownExample send remote 9 rs232 line loopup Send Remote RS232 Line LoopupSend Remote RS232 TSI Loopup Syntax send remote n rs232 tsi equipmentnetwork loopup Send Remote Sdsl Payload LoopupExample send remote 9 sdsl payload loopup Send Remote T1 Payload LoopupExample send remote 9 t1 payload loopup Send Remote T1 TSI LoopupExample send remote 9 t1 tsi loopup Remote loopdown commandExample send remote 9 t1drop line loopup Send Remote T1Drop Line LoopupSend Remote T1Drop Payload Loopup Example send remote 9 t1drop payload loopup Send Remote T1Drop TSI LoopupExample send remote 9 t1drop tsi loopup Send Remote V35 Line LoopupExample send remote 9 v35 line loopup 21. Remote V.35 Line LoopupSend Remote V35 TSI Loopup Send Switch Provision Request Syntax send switch provision requestSyntax send remote n v35 tsi equipmentnetwork loopup Set Alarms Example set alarms major onSet Autoexit Syntax set clock1clock2 setting Setting DescriptionSet Clock Set CRV Idle Set DateSet DS0 CRV Syntax set ds0 nch crv range slc96 513 crv Ds0 49-16 Crv 111-118Ds0 41-24 Crv 311-323 26. DS0s Assigned to CRVs in Odd-Even Order Syntax set ds0 nch isdn none Set DS0 Isdn BRI CRVSyntax set ds0 nch pphone Syntax set ds0 nch pphone none Set DS0 P-PhoneSet DS0 Service Syntax set ds0 nch updownExample set ds0 131-16 up Syntax set ds0 nch signal didemgsgshrgls Set DS0 SignalSet DS0 Type 27. Signaling Used in Common ApplicationsSet DS1 Clock Set DS1 FDLSyntax set ds0 nch type datavoicegr303 Permissible Selections Application Configuration RequirementsApplication FramingExample set ds1 12 fdl none Example set ds1 12 fdl t1403 Set DS1 FramingSyntax set ds1 n framing d4esfslc96 Example set ds1 9 framing esfSet DS1 ID Set DS1 LBOSet DS1 Line Loopup Example set ds1 9 line loopdown Set DS1 LinecodeSyntax set ds1 n linecode amib8zs Example set ds1 9 linecode b8zsExample set ds1 9 loopdetect off Set DS1 LoopdetectSet DS1 Payload Loopup Syntax set ds1 n payload loopuploopdownExample set ds1 9 payload loopdown Example set ds1 Set DS1 Remote Device MgmtMgmt ds1 Mgmt caipSet DS1 TermID Set DS1 ServiceSyntax set ds1 n updown Example set ds1 9 upSet DS1 Threshold Syntax set ds1 n termid idExample set ds1 5 termid Syntax set ds1 n type dropgroomswitch Set DS1 TypeSet EOC Set Ethernet IP Address Syntax set eoc primarysecondary nchnoneSyntax set ethernet ip address address mask Set ID Set IP Gateway AddressExample set id Acme Corp. AN#2 Example set id DNVRCO1A201 Set Remote Config Syntax set ip gateway addressExample set ip gateway Example set ip gateway none Set Remote RS232 Baud Set Remote IDSet Remote RS232 Stop Set Remote RS232 DataSet Remote T1Drop Framing Syntax set remote n t1drop framing d4esfExample set remote 9 t1drop framing d4 Set Remote T1Drop Linecode Set Remote T1Drop LBOSet Remote V35 ClockInv Set Remote T1Drop PRMSet Remote V35 Data Set Remote V35 CTSSet Remote V35 DSU Set Remote V35 RxClockSet Remote V35 Speed Syntax set remote n v35 speed Set ScreenExample set remote 9 v35 speed nx64 Syntax set screen heightoffSet Snmp GetCom Set Snmp ContactSet Snmp Name Set Snmp LocationSet Snmp SetCom Set Snmp NMS AddressSet Snmp TrapCom Set Switch TypeSet TMC Set TimeSyntax set time hhmmss Example set timeSet User Level Syntax set user name level accessSyntax set user name password Show Clock Show AutoexitShow Connect Syntax show autoexitExample show connect Syntax show connect nShow CRV Syntax show crv rangeExample show crv 30. Factory Default Call Reference Values Show DS0 Show DateSyntax show date Syntax show ds0 nchShow DS1 Syntax show ds1 nExample show ds1 Access Navigator Release August 18-141 Remote Device Mgmt on Performance Description ThresholdsSyntax show ds1 all Show DS1 All18-144 Show EOC Show EthernetSyntax show ethernet Show Interface Show IDExample show interface AcmeT1 Example show interface all Syntax show interface nameallShow Isdn CRV Show IPExample show isdn crv Syntax show isdn crv rangeShow Remote Syntax show remote nallExample show remote Example show remote all Show Remote Connections Syntax show remote n connectionsExample show remote 9 connections 18-152 Syntax show snmp Show SnmpSwitch Setting Description Show SwitchShow Time Show TMCAccess Navigator Release August 18-155 Status Clock Status CRV Status DS0 Status DS1 18-160 Status DS1 All Status DS1 Performance Access Navigator Release August 18-163 18-164 Status DS1 Performance History UAS Status EOC Syntax status equipment all Example status equipment Status EquipmentExample status equipment all Status IP Status Isdn CRV Status Remote Status TMC Pots Syntax status tmc allintervalrange Status TMC HistorySwitch Controller Upload Tftp ConfigSyntax switch controller WhoAmI Example upload tftp config 192.168.118.65 CAN2618-178 Appendix Remote Digital Customer Premises Terminal RDT EOC InterfaceAccess Navigator Release August Managed Object Class Support Alarm Count List Objects on page A-5Table A-2 Alarm Count List Objects Alarm Count List ObjectsAttribute Support Command Support Create Get Set Delete Analog Line Termination ObjectsDS1 Framed Path Termination Objects DS0 Channel Termination ObjectsTable A-3 DS0 Channel Termination Objects Table A-4 DS1 Framed Path Termination ObjectsEBS Line Termination Objects DS1 Line Termination ObjectsTable A-5 DS1 Line Termination Objects Table A-6 DS1 Line Termination ObjectsIsdn Framed Path Termination Objects Isdn Line Termination ObjectsTable A-7 Isdn Line Termination Objects Table A-8 Isdn Framed Path Termination ObjectsIsdn Framed Path Termination Objects Crossconnection Quarter DS0 Channel TerminationTable A-9 Isdn Framed Path Termination Objects Table A-10 CrossconnectionIdlc Call Processing Profile Objects Equipment ObjectsTable A-11 Equipment Objects Table A-12 Idlc Call Processing Profile ObjectsTable A-13 Idlc Data Link Profile Objects Idlc Data Link Profile ObjectsTable A-14 Idlc Data Link Termination Objects Idlc Data Link Termination ObjectsMemory Objects Idlc Terminal ObjectsTable A-15 Idlc Terminal Objects Table A-16 Memory ObjectsProtection Group Objects Network Element ObjectsTable A-17 Network Element Objects Table A-18 Protection Group ObjectsTable A-19 Protection Group Unit Objects Protection Group Unit ObjectsActions Table A-20 Action SupportManaged Object Class Action Support Notifications Table A-21 Event Report NotificationManaged Object Class Event Report Notification FDL Interface Figure B-1. FDL Interface FDL InterfaceAccess Bank II Remote Provisioning Requirements Access Navigator Remote Provisioning RequirementsRemote Provisioning Requirements Adit 600 TDM Remote Provisioning RequirementsAccess Bank II Capabilities Access Bank II CapabilitiesInterface Capabilities and Settings Remote Provisioning CapabilitiesRTS FDL Interface Snmp Interface Operations Location Center Snmp InterfaceFigure C-2. Carrier Access Enterprise MIB top level Carrier Access Enterprise MIBMIB Structure Snmp BasicsMIB Tables Table C-1.Standard Snmp Object TypesObject Type Description Managing Networks Table C-2 Standard Snmp MessagesMessage Type Description Snmp Protocols Snmp Requirements Table C-3 Snmp Configuration ItemsTable C-4 Standard Snmp Trap Reports Snmp Trap ReportsTable C-5 Enterprise Snmp Trap Reports Trap Description Test MethodSnmp Interface Glossary LTE GlossaryLult Definitions Page Identifier Access Navigator Release August GlossaryGlossary-7 Electronic Business Set Or Service Access Navigator Release August GlossaryGlossary-9 Multiplex POP RAI Stratum Wide Area Network Wideband GlossaryGlossaryGlossaryGlossary-14 August Index EOC IndexAccess Navigator Release August Index CPE DLC LED FXO TMC LAN T1 TSI MIB Index PRI Sdsl DS1 CRV Isdn BRI CRV Phone Service Signal Type DSU SPR Tftp TSI Index Index