Procedure Summary | Carrier Access Access Navigator instruction

Maintenance Procedures

Replace Unprotected Controller Card

Replace Unprotected Controller Card

Procedure Summary

Precautions ... 16-13

Verify Compatibility ... 16-14

Remove Front Cover ... 16-15

Insert New Controller ... 16-16

Verify Operation and Compatibility ... 16-17

Remove Old Controller ... 16-18

Replace Front Cover ... 16-18

Precautions

CAUTION! THIS PROCEDURE APPLIES ONLY TO ACCESS NAVIGATORS WITH ONE UNPROTECTED CONTROLLER CARD. DO NOT USE THIS PROCEDURE FOR PROTECTED SYSTEMS WITH TWO (REDUNDANT) CONTROLLER CARDS.

TO AVOID SERVICE DISRUPTIONS, DO NOT REMOVE THE ACTIVE CONTROLLER CARD. IF POSSIBLE, INSERT A NEW CONTROLLER CARD AND PUT OLD CONTROLLER CARD IN STANDBY MODE BEFORE REMOVING.

NOTE: This procedure provides steps for replacing a Controller card by installing a new Controller card and then removing the old Controller card. Because the Access Navigator has two card slots for holding Controller cards, a Controller card be replaced without disrupting service. First, the new Controller card is inserted into the empty card slot. The new Controller is given two minutes to reboot and copy system settings from the old card. Then a CLI command is used to switch the old Controller to standby so it can be removed.

Access Navigator - Release 1.8

August 2003

16-13

Image 411

Carrier Access Access Navigator user manual Replace Unprotected Controller Card, Procedure Summary

Contents

Access Navigator Mailtech-support@carrieraccess.com Preface Preface Compliance Electrostatic Discharge ESD Precautions Carrier Access Software License Agreement LicenseTitle and Risk Disclaimer WarrantyCopyright Term Jurisdiction and Venue Limitations of Warranty & Limitation of Remedies Warranty Follow Electrostatic Discharge ESD Precautions on Warranty Product Returns Table of Contents Table of Contents Access Navigator / GR-303 + Data Host Access Navigator / GR-303 Host with P-Phone Electrical Installation Physical Installation 1xv 1xvi August Access Navigator Release Provision Access Navigator Provision DCS ServiceStart Management Session Provision Remote Access Bank Provision GR-303 Service Provision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via FDL Diagnostics & Troubleshooting Alarm Clearing 1xxi Update Controller Card Software Maintenance Procedures CLI Language Reference 1xxiv August Access Navigator Release 1xxv 1xxvi August Access Navigator Release EOC Interface Index FDL InterfaceSnmp Interface Glossary Chapter Introduction Overview Access Navigator Configurations Features and Benefits System Architecture Access Navigator System Architecture Carrier Access Support Products Access BanksAdit Management Command Line Interface Snmp Valet and NetworkValet EMS Software Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Switch Center Co-location Customer Premises Management ServicesFunctions Facilities Network Quad T1 Framer Card Features Controller Card Features Configuration DCS Operation SpecificationsApplications Interfaces Management Interfaces SignalingAlarms System Clocking Physical PowerCompliance Environmental Part Compliance RequirementsFCC Requirements Part 15, Class a Facility Interface Codes FIC Service Order Codes SOCTelcordia Bellcore Requirements UL Requirements Ordering Information CSA RequirementsPart Number Description Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host GR-303 Ethernet RS-232 Modem Voice GR-303 Services Lines Management Key System Access Navigator Data Host Architecture DCS Services IP DS0 Management Management Architecture FDL Management Access Navigator FDL Management Architecture GR-303 call support Applications Crossconnects GR-303 Operation DCS Signaling GR-303 Signaling Compliance Compliance Requirements Telcordia Bellcore Requirements Ordering Information Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 with P-Phone Architecture Features and Benefits Voice Fax P-Phone Service Support Using Adit 600 Terminals Phone Services DCS Services Management Architecture FDL Management Configuration Applications Specifications GR-303 Signaling Standards Compliance Requirements Telcordia Bellcore Requirements Ordering Information Ordering Information Physical Installation Physical Installation Compliance and Safety Requirements Unpacking and Inspection Tools and Materials Installation Summary Precautions Tools and MaterialsHorizontal 19-Inch Rack Mount Attach Access Navigator to Equipment Rack Attach Mounting Brackets to Access Navigator Mounting Four per side Bracket Fasten brackets to Horizontal 23-Inch Rack Mount Assemble Mounting Brackets Installation in 23-inch Equipment Rack Inches minimum Vertical Rack Mount Using Crossbars Attach Access Navigator to Crossbars Install Crossbars Crossbar Installation Inch Equipment Rack Vertical Wall Mount Precautions Prepare Plywood Ensure Adequate Clearance Attach Access Navigator to Plywood Wall View Wire Tie Plywood Sheet Inches Minimum 12. Mounting Hole Pattern on Plywood 13. Wall Mount Bracket Installation Physical Installation Electrical Installation Electrical Installation Static-Sensitive Equipment Handling Procedures Tools and Materials Required Chassis Ground Connection Connect Ground Wire to Ground Lug Run Ground Wire to Access Navigator Attach Ground Lug to Access Navigator DSX-1 Cable Connections Prepare DSX-1 Cables CAC Location of Rear Panel DS1 Connectors Connect DSX-1 Cables to Access Navigator Electrical Installation Attaching Ferrite Bead RF Suppressors Attach Ferrite Beads Connect DSX-1 Cables to Interface or Patch Panel Card Group DSX-1 Cable Pin Connections and Flying Wire Colors Electrical Installation Information, Tools, and Materials RS-232 Management Connection RS-232 DTE-to-DCE Cable RS-232 DCE-to-DCE Modem Cable Connections Connect Shielded RS-232 Cable 10. Attaching Ferrite Bead RF Suppressor Attach Ferrite Bead RF Suppressor Preconfigure Optional Modem Ethernet Management Connection Information and MaterialsMake Ethernet Cable Optional MDI Port Pins Signals Connect Ethernet Cable to Ethernet Hub Connect Ethernet Cable to Access Navigator External Timing Source Bits Connection Connect Bits Cable Make Bits Cable Optional Alarm Output Connections 15. Alarm Output Connector Wire Alarm Output Connector Maximum 18. Location of Rear Panel Alarm Output Connector Plug Output Alarm Connector into Access Navigator Alarm Input Connections 19. Alarm Input Connector Wire Alarm Input Connector Cable Shield 22. Location of Rear Panel Alarm Input Connector Plug Alarm Input Connector into Access Navigator DC Power Connections Used Wire Power Connectors Connect Power Plugs to Access Navigator Verify Wiring Dress Cables and Wires Dress Cables and Wires Verification Summary Acceptance Test 26. Location of Front Panel Power-On Status LEDs Apply Power and Verify Operation Verify DSX-1 Connections Verify Chassis Ground Connection Verify RS-232 Management Connection Verify Ethernet Management Connection Verify Ethernet Cable Connection Set clock1 bits set clock2 bits Verify Bits Connection Controller ’A’ Indicators Controller ’B’ Indicators Verify Alarm Output Connections Electrical Installation 31. Location of Rear Panel Alarm Input Connector Verify Alarm Input Connections Exit Exit Management Session Install Redundant Controller Card Verify Software Compatibility 33. Location of Front Panel Cover Screws Remove Front Cover 34. Location of Controller Cards Install Controller Card Verify Operation Switch controller Replace Front Cover Install Additional Quad T1 Framer Cards 37. Location of Front Panel Cover Screws 38. Location of Quad T1 Framer Cards Install Quad T1 Framer Card Eject Set ds1 n up Status equipment Set ds1 n down 29-32 13-16 17-20 21-24 26-28 Configure Management Interfaces Setup SummaryReplace Front Cover Start RS-232 Management Session Set Time Set Date Set IP Address and Subnet Mask Set System ID or Clli code Set Gateway Address Exit Management Session Start Management Session Start Management Session Management Requirements Show ds1 Command Line Interface Conventions Procedure Summary RS-232 ManagementRS-232 Management Requirements Connect RS-232 Cable to Access Navigator Set Up Terminal ProgramObtain Information Start RS-232 Management Session Exit RS-232 Management Session Perform Management Operations Telnet Management Requirements Telnet Management Start Telnet Management Session Start Telnet Program and Connect to Access Navigator Exit Telnet Management Session When Finished NetworkValet EMS and Valet Management Start Management Session Provision Access Navigator Basic Provisioning Quick Guide Provision Access NavigatorCLI Commands Descriptions Basic Provisioning Overview Obtain Provisioning Information Verify System Equipment Configuration Show id Set System ID or Clli Code Show time Set DateSet Time Show date Set Ethernet Properties Set ethernet ip address none Set User and Password Security Set user Alice password DNVRCO1A201 Set Snmp Properties Example Set snmp nms 1 Provision DCS Service DCS Provisioning Overview Provision DCS Service Provisioning TR-08 Service with DCS Provisioning Isdn BRI Service Provisioning Voice Services for TR-08 Shelves B, C, and D Provisioning Conventional TR-08 Voice Services Special TR-08 Settings Provisioning Enhanced Voice and Data Services DCS Provisioning Quick Guide Card not installed Show ds1 all Verify Service Status Status ds1 n Set ds1 n down Set ds0 nch type voicedata Set Unused Circuits Out of Service Set System Clock Source CAC Provision Groom DS1 Circuits to Network Example Set ds1 10 loopdetect on Provision Drop DS1 Circuits to Subscribers Test Groom DS1 Circuits Set ds1 20 framing esf Provision and Connect Isdn BRI 3DS0 Channels Provision and Connect Isdn PRI Channels Provision and Connect DS0s DS0 #10 Turn Up Service Test DS1 and DS0 CircuitsSet ds1 n up set ds0 nch up Test DS1 and DS0 Circuits Provision GR-303 Service GR-303 Provisioning Overview Provision GR-303 Service Access Navigator GR-303 Services Provisioning P-Phone Service Provisioning TR-08 Service to Access Banks Provisioning TR-08 Service with GR-303 Translation CRV Numbering TR-08 ConfigurationSignaling Translation Special Pots Cards Set ds0 41-24 crv 311-334 slc96 Set ds0 49-16 crv Framing and FDL Settings Access Bank I/TR-08 Switch SettingsSwitch Shelf Access Bank I/TR-08 Loopback Code Response GR-303 Provisioning Quick Guide Isdn BRI 41 TDM channels Connect Isdn D channel to SwitchSet DS0s in service Set DS1s in service Access Navigator Release August 10-11 10-12 Set ds1 n down set ds0 nch down Show switch Set System Switch Type Provision Switch DS1s to Interface Group 10-16 Access Navigator Release August 10-17 Assign Primary and Secondary EOC Set tmc primary nchnone Assign Primary and Secondary TMC Test DS1 Circuits Provision Drop DS1 Circuits to Subscriber Set ds1 n framing d4esfslc96 Example Set ds1 Fdl none Fdl t1403 10-24 Provision Isdn BRI 41 TDM Service to Subscribers CRV Show isdn database Send switch provision request 10-28 Access Navigator Release August 10-29 Provision DS0s to Subscribers Set ds0 nch type gr303 Assign Call Reference Values CRVs Example Set ds0 21-4 crv Test Circuits Provision Remote Access Bank Provision Remote Access Bank Remote Access Bank II Provisioning Overview Requirements Pre-Provisioning and Testing Analog Interfaces Crossconnect Features Crossconnections Abii Valid Crossconnect Assignments FX Analog Interfaces FX Interfaces Support Analog Voice and Data Services Fractional Interfaces Valid Interface AssignmentsInterface Type DS1 Type DS0 Type Voice Data GR-303 Remote Interfaces Remote Access Bank II Provisioning Quick Guide Remote Access Bank II Maintenance Quick Guide DS1 Card Installed Card not installed 11-12 Access Navigator Release August 11-13 Temporarily Disable Configuration Downloading Provision Drop DS1 to Remote Access Bank Set ds1 n remote device management cafdl Provision DS0s Set ds0 nch type voicedatagr303 Provision DS0 Crossconnects Example connect 2519-24 Create Fractional Interfaces if required Configure Remote RS-232 Interface if used Set baud rate with the following command Configure Remote T1 Drop Interface if used Set remote n t1drop lbo setting Set remote n t1drop linecode amib8zsSet remote n t1drop prm ansiatt Configure Remote V.35 Interface if used Set remote n v35 clkinv rxtxrxtxnone Connect Fractional Interface to Remote Interface Download Configuration to Remote Access Bank Verify Downloaded Settings optional Call Status FX and Spots To Loop or Test Remote Circuits Provision Remote Adit 600 via FDL Provision Remote Adit 600 via FDL Remote Adit 600 FDL Provisioning Overview On-Net Customer Location Premises FDL Management Configuration Remote Adit 600 FDL Provisioning Quick Guide Set Provision Remote Adit 600 via FDL Verify Equipment Configuration Access Navigator Release August 12-7 Status remote nall CA FDL Interface Provision Drop DS1s to Remote Adit Set ds1 n linecode amib8zs 12-12 Provision Drop DS0s Set ds0 nch up Example set ds0 101-24 up Set ds0 nch signal lsgsem Provision DS0 Crossconnects if required Crossconnect Examples Logon remote n Provision Remote Adit 12-18 Provision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via IP DS0 Remote IP DS0 Provisioning Overview Carrier Access IP DS0 Management Configuration IP DS0 Management Configuration Remote IP DS0 Provisioning Quick Guide Access Navigator CLI Commands Descriptions Verify status of management channel Adit CLI Commands DescriptionsRouter Setup Router Provisioning Quick Guide Set Device Name to Adit1 Select the PVC Management as Disabled Remote Adit IP DS0 Provisioning Quick Guide 13-8 Access Navigator Release August 13-9 13-10 Out of Service Provision Groom DS1s to Adit Router Set ds1 32 framing esf 13-14 Access Navigator Release August 13-15 Set ds1 n remote device management caip ipaddr pphone Set ds1 n framing d4esf Set DS1 identification Provision Groom DS0s to Adit Router Provision Drop DS0s to Remote Adit 13-20 Access Navigator Release August 13-21 13-22 Access Navigator Release August 13-23 13-24 Alarm Clearing Identify Alarm Clearing Procedure Alarm ClearingFacility Alarm System go to Clear Alarms FDL on Set alarms critical off Clear Alarms FDLCLI Critical Alarm Message and Trouble Clearing Procedure Event Message Description Trouble Clearing Procedure Set ds1 n updown CLI Major Alarm Message and Trouble Clearing Procedure Card Software on CLI Minor Alarm Message and Trouble Clearing Procedure Show eoc Status eoc Show tmc Status tmc EOC Critical Alarm Message and Trouble Clearing Procedure Clear Alarms EOC EOC Major Alarm Message and Trouble Clearing Procedure EOC Minor Alarm Message and Trouble Clearing Procedure Active 14-12 Switch EOC Warning Alarm Message and Trouble Clearing Procedure Clear Alarms Snmp Trap Message and Trouble Clearing ProcedureTrap Message Description Trouble Clearing Procedure Alarm Indicators Clear Alarms Status Indicators Power Status LEDs Power Status LEDsLED State Description Troubleshooting 10. Active/Standby Controller Status LEDs Status equipment command forSystem, use the switch controller Active/Standby Controller Status LEDs 12. Major Alarm Status LEDs Critical Alarm Status LEDsMajor Alarm Status LEDs 11. Critical Alarm Status LEDs 14. Alarm Cutoff ACO Status LEDs Minor Alarm Status LEDsAlarm Cutoff ACO Status LED 13. Minor Alarm Status LEDs Set ds1 up command DS1 Status LEDs15. DS1 Status LEDs 16. Ethernet Link Status LED Ethernet Link Status LED 14-22 Diagnostics & Troubleshooting Alarms and Logs Diagnostics & TroubleshootingOperations Interface Syntax set alarms criticalmajorminor onoff Alarm ReportingAlarm Testing Alarm and Status Indicators Facility Alarm System Alarm Cutoff ACOAlarm Signaling Red, Yellow RAI, Blue AIS DS1 Failures Event LogSyntax log majorminoralertinfo Configuration Change Log Syntax log tmc permanent Bert LogTMC Log Syntax clear bert log Indicator Locations Alarm and Status Indicators Rear Panel Ethernet Indicator Green Indicator DescriptionsIndicator Descriptions State Description Status and Performance Status ClockSyntax status clock Status DS0 Syntax status ds0 nchExample status ds0 Example status ds1 Status DS1Syntax status ds1 n Field Description Syntax status ds1 all Status DS1 All Access Navigator Release August 15-15 Status DS1 Performance Syntax status ds1 n performanceExample status ds1 9 performance Status DS1 Performance History Syntax status ds1 n performance historyExample status ds1 9 performance history Syntax clear ds1 n performance Clear DS1 Performance Syntax status equipment Status Equipment Syntax status ip Status IP Example status remote all Status RemoteSyntax status remote nall Field Example status crv GR-303 Status and PerformanceStatus CRV Syntax status crv range Status Isdn CRV Syntax status isdn crv rangeExample status isdn crv 15-24 Syntax status tmc Status EOCStatus TMC Syntax status eoc Originating Calls Blocked Calls Secondary Status TMC History Syntax status tmc allintervalExample status tmc all Set CRV Idle Clear Blocked Call CountClear Peak Call Count Clear Permanent Call Count Syntax set ds1 n loopdetect onoff Near-End LoopbacksDS1 Loopdetect DS1 FDL Protocol Syntax set ds1 n payload loopdownloopup DS1 Line LoopbackDS1 Payload Loopback Syntax set ds1 n line loopdownloopup Far-End Loopbacks DS1 CSU LoopupSyntax send ds1 n csu loopuploopdown Syntax send ds1 n line loopuploopdown DS1 Line Loopup Syntax send ds1 n network loopuploopdown DS1 Network Loopup Syntax send ds1 n niu loopuploopdown DS1 NIU Loopup Syntax send ds1 n payload loopuploopdown DS1 Payload Loopup Syntax read remote n loopback Access Bank II LoopbacksRead Remote Loopback Send Remote Loopdown Syntax send remote 9 rs232 tsi equipment loopup Send Remote RS232 Line LoopupSend Remote RS232 TSI Equipment Loopup Syntax send remote n rs232 line loopup Syntax send remote n sdsl payload loopup Send Remote RS232 TSI Network LoopupSend Remote Sdsl Payload Loopup Syntax send remote 9 rs232 tsi network loopup Syntax send remote n t1 tsi loopup Send Remote T1 Payload LoopupSend Remote T1 TSI Loopup Syntax send remote n t1 payload loopup Syntax send remote n t1drop payload loopup Send Remote T1 Drop Line LoopupSend Remote T1 Drop Payload Loopup Syntax send remote n t1drop line loopup Send Remote V35 Line Loopup Syntax send remote n t1drop tsi loopupSyntax send remote n v35 line loopup Syntax send remote n v35 tsi network loopup Send Remote V35 TSI Equipment LoopupSend Remote V35 TSI Network Loopup Syntax send remote n v35 tsi equipment loopup Syntax send ds1 n off Bit Patterns and Error TestsSend DS1 Pattern Off Send DS1 Line Pattern Syntax send ds1 n line p2e11p2e15p2e23qrss Send DS1 Payload Pattern Access Navigator Payload Code Send DS1 Line Pattern with BER Test Example set ds1 9 line p2e15 test Syntax send ds1 n line p2e11p2e15p2e23qrss test FBE 26. Send DS1 Payload Pattern with BER Test Send DS1 Payload Pattern with BER Test Example send ds1 9 payload p2e15 test Test Example 15-52 Other Maintenance Commands Load tftp config ipaddr file Show usersWhoami Show isdn database show crv database Technical Support Trace eoc Off Trace tmc onLet run for 2 or 3 minutes Trace tmc off Trace eoc Maintenance Procedures Maintenance Procedures Repair and Return Procedure Overview Replace Controller Card Tools and Materials Required Verify Equipment Status Determine Which Replacement Procedure to Use Procedure Summary PrecautionsReplace Protected Controller Card Verify Compatibility Remove Front Cover Location of Controller Cards Replace Standby Controller Installing and Removing Controller Card Verify Operation and Compatibility Replace Other Controller Card Replace Unprotected Controller Card Controller B Active DS1 Card Installed Access Navigator Release August 16-15 Insert New Controller Access Navigator Release August 16-17 Remove Old Controller Replace Quad T1 Framer Card OverviewQF Card Slot DS1 Circuit Numbers Tools and Materials Required Set clock2 ds1 n Verify Equipment StatusTemporarily Move Clock Sources if required Set clock1 ds1 n Location of Front Panel Cover Screws 10. Location of Quad T1 Framer Cards Replace Quad T1 Card 11. Installing Quad T1 Framer Card Verify Operation 12. Location of Front DS-1 Status Indicators Show clock Restore Clock Sources if required Install Simm on Controller Card Precautions Tools and Materials Required 16-30 Standby Controller ACTIVE/STANDBY indicator is off 14. Location of Front Panel Cover Screws 15. Location of Controller Cards Install Simm Simm Access Navigator Release August 16-35 16-36 Update Controller Card Software Update Controller Card Software Download Procedures Update Software via Tftp Two Controllers Tftp RequirementsEvent Log 17-4 Information and Materials Required Install Optional Tftp Server Software Requirement One Controller is in Standby Status equipment all Verify IP Connectivity Upload Configuration Download Software Show ds0 Set ds0 321 up set ds0 321 downSet ds0 321 down set ds0 321 up Example load tftp config 192.168.118.65 AN26 Download Configuration Xmodem Requirements Update Software via Xmodem Two Controllers 17-12 Access Navigator Release August 17-13 System Access Navigator Release August 17-15 17-16 Update Software via Xmodem One Controller 17-18 SW Build Number 17701 Boot Code Revision 01.09 Minutes Access Navigator Release August 17-21 17-22 CLI Language Reference CLI Language Reference CLI Access Via RS-232 and Telnet Terminal emulation Port settingsCLI Requirements CLI over RS-232 Ethernet interface Access Navigator IP addressCLI over Telnet RS-232 interface for modem connection Using CLI Command Scripts Character and Line DelaysConfirmations and Errors SystemID set ds1 24 framing esf Command CategoriesCommands, Confirmations, and Error Messages CLI Conventions and Shortcuts Text Conventions SystemID set ds1 42 framing esfSet ds1 1-4 up Command Syntax Descriptions Command Shortcuts Tabbing Entering DS1 and DS0 Numbers and RangesKeyboard Shortcuts Displaying Basic Commands Online HelpHelp System Overview Context Sensitive Help 18-12 Syntax print help Printing the Help File User Level Access Users and PasswordsAdministration Access Levels Syntax show users Managing UsersWho Am Show Users Set User Access Level Add UserSyntax add user name Example add user alice Delete User Set User PasswordDelete User Password Access Definition Login with No User Name Required Logging In and OutStartup Message Login with User Name Required Login with No Password RequiredLogin with Password Required Example set autoexit Autoexit CLI Session TimeoutLogout Exit Syntax set autoexit minutes ACO CLI Command List CLI Language Reference Add Interface ACO Type Description Remote Port Maximum Number of DS0s Alarms Syntax alarms majorminoralertSyntax add user name Syntax alarms equipment majorminoralert Syntax alarms ds1 nallSyntax alarms ds1 nall majorminoralert Syntax alarms equipment Clear DS1 Performance Clear Config LogClear Bert Log Clear Blocked Call Count Clear Remote Log Clear LogClear Peak Call Count Clear Permanent Call Count Example connect 2519-24 Connect 18-30 Drop Groom Switch Connect Remote InterfaceDrop Example delete interface AcmeV35 Delete InterfaceSyntax connect remote name fxrs232sdslt1dropv35 Syntax delete interface name Example disconnect DisconnectSyntax delete user name Syntax disconnect nch Syntax disconnect remote name Disconnect RemoteExit Exit Remote Session Ctrl+C Xmodem Load Active Load Tftp Config Log Example load tftp config 192.168.118.65 AN26 Example log equipment minor Example log Message Log Bert Example log config ds0 Log Config Description Example log config Example log tmc Message Log TMC Logon Remote Syntax logon remote nExample logon remote Ping Read Remote AlarmsSyntax read remote n alarms Example read remote 9 alarms 18-46 Access Navigator Release August 18-47 Read Remote Connections Syntax read remote n connectionsExample read remote 9 connections Access Navigator Release August 18-49 Read Remote Log Syntax read remote n logExample read remote 9 log Syntax read remote n rs232 Read Remote LoopbackRead Remote RS232 Example read remote 9 loopback Syntax read remote n t1t1drop performance Read Remote Performance Access Navigator Release August 18-53 Syntax read remote n t1 Read Remote T1 Read remote T1drop Read Remote T1dropLevel 3 monitor Read remote Read Remote Syntax read remote nExample read remote 9 Syntax reset ds1 n Reset AllReset DS1 Framer Syntax reset all Example reset remote Reset RemoteReset Standby Syntax reset remote n Parameter Default Comments Restore DefaultsDefault Settings Syntax restore defaults Normal CLI Language Reference Line loopback deactivate Send DS1 CSU Loopup Send DS1 Line Loopup Example send ds1 9 csu loopupExample send ds1 9 csu loopdown 00001110 11111111 Send DS1 Line pattern Example send ds1 9 line loopupExample send ds1 9 line loopdown Send DS1 Line Pattern Example set ds1 9 line p2e15 Send DS1 Line pattern Test Send DS1 Line Pattern with BER Test Access Navigator Release August 18-69 Send DS1 Network Loopup Send DS1 Network Loopup Send DS1 NIU Loopup Example send ds1 9 network loopupExample send ds1 9 network loopdown Example send ds1 9 niu loopup Syntax send ds1 n niu loopup loopdown Example send ds1 9 niu loopdown Send DS1 Payload Loopup Example send ds1 9 payload loopdown Example send ds1 9 payload loopup Send DS1 Payload pattern 10. Send DS1 Payload Pattern Example send ds1 9 payload p2e15 Send DS1 Payload pattern Test 11. Send DS1 Payload Pattern with BER Test P2e11 Example set ds1 9 payload p2e15 test Example send ds1 9 payload f1in8 test Example send remote 9 loopdown Send DS1 OffSend Remote Loopdown Example send ds1 9 off Example send remote 9 rs232 line loopup Send Remote RS232 Line Loopup Send Remote RS232 TSI Loopup Syntax send remote n rs232 tsi equipmentnetwork loopup Send Remote Sdsl Payload Loopup Example send remote 9 sdsl payload loopup Send Remote T1 Payload Loopup Example send remote 9 t1 payload loopup Send Remote T1 TSI Loopup Example send remote 9 t1 tsi loopup Remote loopdown command Example send remote 9 t1drop line loopup Send Remote T1Drop Line Loopup Send Remote T1Drop Payload Loopup Example send remote 9 t1drop payload loopup Send Remote T1Drop TSI Loopup Example send remote 9 t1drop tsi loopup Send Remote V35 Line Loopup Example send remote 9 v35 line loopup 21. Remote V.35 Line Loopup Send Remote V35 TSI Loopup Send Switch Provision Request Syntax send switch provision requestSyntax send remote n v35 tsi equipmentnetwork loopup Set Alarms Example set alarms major onSet Autoexit Syntax set clock1clock2 setting Setting DescriptionSet Clock Set CRV Idle Set DateSet DS0 CRV Syntax set ds0 nch crv range slc96 513 crv Ds0 49-16 Crv 111-118Ds0 41-24 Crv 311-323 26. DS0s Assigned to CRVs in Odd-Even Order Syntax set ds0 nch isdn none Set DS0 Isdn BRI CRV Syntax set ds0 nch pphone Syntax set ds0 nch pphone none Set DS0 P-Phone Set DS0 Service Syntax set ds0 nch updownExample set ds0 131-16 up Syntax set ds0 nch signal didemgsgshrgls Set DS0 Signal Set DS0 Type 27. Signaling Used in Common Applications Set DS1 Clock Set DS1 FDLSyntax set ds0 nch type datavoicegr303 Framing Application Configuration RequirementsPermissible Selections Application Example set ds1 9 framing esf Set DS1 FramingExample set ds1 12 fdl none Example set ds1 12 fdl t1403 Syntax set ds1 n framing d4esfslc96 Set DS1 ID Set DS1 LBOSet DS1 Line Loopup Example set ds1 9 linecode b8zs Set DS1 LinecodeExample set ds1 9 line loopdown Syntax set ds1 n linecode amib8zs Example set ds1 9 loopdetect off Set DS1 Loopdetect Set DS1 Payload Loopup Syntax set ds1 n payload loopuploopdownExample set ds1 9 payload loopdown Mgmt caip Set DS1 Remote Device MgmtExample set ds1 Mgmt ds1 Example set ds1 9 up Set DS1 ServiceSet DS1 TermID Syntax set ds1 n updown Set DS1 Threshold Syntax set ds1 n termid idExample set ds1 5 termid Syntax set ds1 n type dropgroomswitch Set DS1 TypeSet EOC Set Ethernet IP Address Syntax set eoc primarysecondary nchnoneSyntax set ethernet ip address address mask Set ID Set IP Gateway AddressExample set id Acme Corp. AN#2 Example set id DNVRCO1A201 Set Remote Config Syntax set ip gateway addressExample set ip gateway Example set ip gateway none Set Remote RS232 Baud Set Remote ID Set Remote RS232 Stop Set Remote RS232 Data Set Remote T1Drop Framing Syntax set remote n t1drop framing d4esfExample set remote 9 t1drop framing d4 Set Remote T1Drop Linecode Set Remote T1Drop LBO Set Remote V35 ClockInv Set Remote T1Drop PRM Set Remote V35 Data Set Remote V35 CTS Set Remote V35 DSU Set Remote V35 RxClockSet Remote V35 Speed Syntax set screen heightoff Set ScreenSyntax set remote n v35 speed Example set remote 9 v35 speed nx64 Set Snmp GetCom Set Snmp Contact Set Snmp Name Set Snmp Location Set Snmp SetCom Set Snmp NMS Address Set Snmp TrapCom Set Switch Type Example set time Set TimeSet TMC Syntax set time hhmmss Set User Level Syntax set user name level access Syntax set user name password Syntax show autoexit Show AutoexitShow Clock Show Connect Example show connect Syntax show connect n Show CRV Syntax show crv rangeExample show crv 30. Factory Default Call Reference Values Syntax show ds0 nch Show DateShow DS0 Syntax show date Show DS1 Syntax show ds1 nExample show ds1 Access Navigator Release August 18-141 Remote Device Mgmt on Performance Description Thresholds Syntax show ds1 all Show DS1 All 18-144 Show EOC Show EthernetSyntax show ethernet Show Interface Show ID Example show interface AcmeT1 Example show interface all Syntax show interface nameall Show Isdn CRV Show IP Example show isdn crv Syntax show isdn crv range Show Remote Syntax show remote nallExample show remote Example show remote all Show Remote Connections Syntax show remote n connectionsExample show remote 9 connections 18-152 Syntax show snmp Show Snmp Show TMC Show SwitchSwitch Setting Description Show Time Access Navigator Release August 18-155 Status Clock Status CRV Status DS0 Status DS1 18-160 Status DS1 All Status DS1 Performance Access Navigator Release August 18-163 18-164 Status DS1 Performance History UAS Status EOC Syntax status equipment all Example status equipment Status Equipment Example status equipment all Status IP Status Isdn CRV Status Remote Status TMC Pots Syntax status tmc allintervalrange Status TMC History Switch Controller Upload Tftp ConfigSyntax switch controller WhoAmI Example upload tftp config 192.168.118.65 CAN26 18-178 Appendix Remote Digital Customer Premises Terminal RDT EOC Interface Access Navigator Release August Managed Object Class Support Alarm Count List Objects on page A-5 Analog Line Termination Objects Alarm Count List ObjectsTable A-2 Alarm Count List Objects Attribute Support Command Support Create Get Set Delete Table A-4 DS1 Framed Path Termination Objects DS0 Channel Termination ObjectsDS1 Framed Path Termination Objects Table A-3 DS0 Channel Termination Objects Table A-6 DS1 Line Termination Objects DS1 Line Termination ObjectsEBS Line Termination Objects Table A-5 DS1 Line Termination Objects Table A-8 Isdn Framed Path Termination Objects Isdn Line Termination ObjectsIsdn Framed Path Termination Objects Table A-7 Isdn Line Termination Objects Isdn Framed Path Termination Objects Table A-10 Crossconnection Quarter DS0 Channel TerminationCrossconnection Table A-9 Isdn Framed Path Termination Objects Table A-12 Idlc Call Processing Profile Objects Equipment ObjectsIdlc Call Processing Profile Objects Table A-11 Equipment Objects Table A-13 Idlc Data Link Profile Objects Idlc Data Link Profile Objects Table A-14 Idlc Data Link Termination Objects Idlc Data Link Termination Objects Table A-16 Memory Objects Idlc Terminal ObjectsMemory Objects Table A-15 Idlc Terminal Objects Table A-18 Protection Group Objects Network Element ObjectsProtection Group Objects Table A-17 Network Element Objects Table A-19 Protection Group Unit Objects Protection Group Unit Objects Actions Table A-20 Action SupportManaged Object Class Action Support Notifications Table A-21 Event Report NotificationManaged Object Class Event Report Notification FDL Interface Figure B-1. FDL Interface FDL Interface Adit 600 TDM Remote Provisioning Requirements Access Navigator Remote Provisioning RequirementsAccess Bank II Remote Provisioning Requirements Remote Provisioning Requirements Remote Provisioning Capabilities Access Bank II CapabilitiesAccess Bank II Capabilities Interface Capabilities and Settings RTS FDL Interface Snmp Interface Operations Location Center Snmp Interface Figure C-2. Carrier Access Enterprise MIB top level Carrier Access Enterprise MIB MIB Structure Snmp Basics MIB Tables Table C-1.Standard Snmp Object TypesObject Type Description Managing Networks Table C-2 Standard Snmp MessagesMessage Type Description Snmp Protocols Snmp Requirements Table C-3 Snmp Configuration Items Trap Description Test Method Snmp Trap ReportsTable C-4 Standard Snmp Trap Reports Table C-5 Enterprise Snmp Trap Reports Snmp Interface Glossary LTE Glossary Lult Definitions Page Identifier Access Navigator Release August GlossaryGlossary-7 Electronic Business Set Or Service Access Navigator Release August GlossaryGlossary-9 Multiplex POP RAI Stratum Wide Area Network Wideband GlossaryGlossaryGlossaryGlossary-14 August Index EOC Index Access Navigator Release August Index CPE DLC LED FXO TMC LAN T1 TSI MIB Index PRI Sdsl DS1 CRV Isdn BRI CRV Phone Service Signal Type DSU SPR Tftp TSI Index Index