Carrier Access Access Navigator specification

Maintenance Procedures

Replace Unprotected Controller Card

Verify Compatibility

1.Display current Controller status and software version by entering the following command: status equipment

A message similar to the following will appear, showing the equipment card slots, service status, and Controller software version.

Equipment	Status	Version
---------	------	-------
Controller A	Card not installed	1.70
Controller B	Active	1.70
DS1 Card 1	Installed	1
DS1 Card 2	Installed	1
DS1 Card 3	Installed	1
DS1 Card 4	Installed	1
DS1 Card 5	Installed	1
DS1 Card 6	Installed	1
DS1 Card 7	Card not installed
DS1 Card 8	Card not installed

NOTE: In an unprotected system with only one Controller card, the Controller will have “Active” status and the other Controller card slot status will show “Card not installed”.

2.If new Controller card version is compatible with installed active Controller card, skip remaining steps.

3.If new Controller card version is NOT compatible with installed active Controller card, continue this procedure only if prepared for a service interruption and loss of provisioning. Verify provisioning both before and after performing this procedure. Make provisioning changes as required to re-establish service.

16-14

August 2003

Access Navigator - Release 1.8

Image 412

Carrier Access Access Navigator user manual Controller B Active DS1 Card Installed

Contents

Access Navigator Mailtech-support@carrieraccess.com Preface Compliance Preface Electrostatic Discharge ESD Precautions License Carrier Access Software License AgreementTitle and Risk Warranty CopyrightTerm Disclaimer Jurisdiction and Venue Warranty Limitations of Warranty & Limitation of Remedies Warranty Product Returns Follow Electrostatic Discharge ESD Precautions on Table of Contents Access Navigator / GR-303 + Data Host Table of Contents Access Navigator / GR-303 Host with P-Phone Physical Installation Electrical Installation 1xv 1xvi August Access Navigator Release Provision DCS Service Provision Access NavigatorStart Management Session Provision GR-303 Service Provision Remote Access Bank Provision Remote Adit 600 via FDL Provision Remote Adit 600 via IP DS0 Alarm Clearing Diagnostics & Troubleshooting 1xxi Maintenance Procedures Update Controller Card Software CLI Language Reference 1xxiv August Access Navigator Release 1xxv 1xxvi August Access Navigator Release EOC Interface FDL Interface Snmp InterfaceGlossary Index Chapter Overview Introduction Features and Benefits Access Navigator Configurations Access Navigator System Architecture System Architecture Access Banks Carrier Access Support ProductsAdit Command Line Interface Management Snmp Valet and NetworkValet EMS Software Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Switch Center Co-location Customer Premises Services FunctionsFacilities Management Network Configuration Quad T1 Framer Card Features Controller Card Features Specifications ApplicationsInterfaces DCS Operation Signaling AlarmsSystem Clocking Management Interfaces Power ComplianceEnvironmental Physical Compliance Requirements FCC RequirementsPart 15, Class a Part Service Order Codes SOC Telcordia Bellcore RequirementsUL Requirements Facility Interface Codes FIC CSA Requirements Ordering InformationPart Number Description Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host GR-303 Ethernet RS-232 Modem Voice GR-303 Services Lines Management Key System DCS Services Access Navigator Data Host Architecture Management Architecture IP DS0 Management Access Navigator FDL Management Architecture FDL Management GR-303 call support Applications GR-303 Operation Crossconnects GR-303 Signaling DCS Signaling Compliance Compliance Requirements Telcordia Bellcore Requirements Ordering Information Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 with P-Phone Architecture Features and Benefits Voice Fax Phone Services P-Phone Service Support Using Adit 600 Terminals DCS Services Management Architecture FDL Management Configuration Applications Specifications GR-303 Signaling Standards Compliance Requirements Telcordia Bellcore Requirements Ordering Information Ordering Information Physical Installation Compliance and Safety Requirements Physical Installation Tools and Materials Unpacking and Inspection Precautions Tools and Materials Installation SummaryHorizontal 19-Inch Rack Mount Attach Mounting Brackets to Access Navigator Attach Access Navigator to Equipment Rack Mounting Four per side Bracket Fasten brackets to Horizontal 23-Inch Rack Mount Assemble Mounting Brackets Installation in 23-inch Equipment Rack Inches minimum Vertical Rack Mount Using Crossbars Install Crossbars Attach Access Navigator to Crossbars Crossbar Installation Inch Equipment Rack Precautions Vertical Wall Mount Ensure Adequate Clearance Prepare Plywood Attach Access Navigator to Plywood Wall View Wire Tie Plywood Sheet Inches Minimum 12. Mounting Hole Pattern on Plywood 13. Wall Mount Bracket Installation Physical Installation Electrical Installation Electrical Installation Static-Sensitive Equipment Handling Procedures Tools and Materials Required Chassis Ground Connection Run Ground Wire to Access Navigator Connect Ground Wire to Ground Lug Attach Ground Lug to Access Navigator DSX-1 Cable Connections Prepare DSX-1 Cables CAC Connect DSX-1 Cables to Access Navigator Location of Rear Panel DS1 Connectors Electrical Installation Attach Ferrite Beads Attaching Ferrite Bead RF Suppressors Connect DSX-1 Cables to Interface or Patch Panel DSX-1 Cable Pin Connections and Flying Wire Colors Card Group Electrical Installation RS-232 Management Connection Information, Tools, and Materials RS-232 DTE-to-DCE Cable Connect Shielded RS-232 Cable RS-232 DCE-to-DCE Modem Cable Connections Attach Ferrite Bead RF Suppressor 10. Attaching Ferrite Bead RF Suppressor Preconfigure Optional Modem Information and Materials Ethernet Management ConnectionMake Ethernet Cable Optional MDI Port Pins Signals Connect Ethernet Cable to Access Navigator Connect Ethernet Cable to Ethernet Hub External Timing Source Bits Connection Make Bits Cable Optional Connect Bits Cable Alarm Output Connections Wire Alarm Output Connector 15. Alarm Output Connector Maximum Plug Output Alarm Connector into Access Navigator 18. Location of Rear Panel Alarm Output Connector Alarm Input Connections Wire Alarm Input Connector 19. Alarm Input Connector Cable Shield Plug Alarm Input Connector into Access Navigator 22. Location of Rear Panel Alarm Input Connector DC Power Connections Wire Power Connectors Used Verify Wiring Connect Power Plugs to Access Navigator Dress Cables and Wires Dress Cables and Wires Acceptance Test Verification Summary Apply Power and Verify Operation 26. Location of Front Panel Power-On Status LEDs Verify Chassis Ground Connection Verify DSX-1 Connections Verify RS-232 Management Connection Verify Ethernet Cable Connection Verify Ethernet Management Connection Verify Bits Connection Set clock1 bits set clock2 bits Verify Alarm Output Connections Controller ’A’ Indicators Controller ’B’ Indicators Electrical Installation Verify Alarm Input Connections 31. Location of Rear Panel Alarm Input Connector Exit Management Session Exit Install Redundant Controller Card Verify Software Compatibility Remove Front Cover 33. Location of Front Panel Cover Screws Install Controller Card 34. Location of Controller Cards Switch controller Verify Operation Replace Front Cover Install Additional Quad T1 Framer Cards 37. Location of Front Panel Cover Screws Install Quad T1 Framer Card 38. Location of Quad T1 Framer Cards Eject Status equipment Set ds1 n up 29-32 13-16 17-20 21-24 26-28 Set ds1 n down Setup Summary Configure Management InterfacesReplace Front Cover Start RS-232 Management Session Set Date Set Time Set System ID or Clli code Set IP Address and Subnet Mask Set Gateway Address Exit Management Session Start Management Session Management Requirements Start Management Session Command Line Interface Conventions Show ds1 RS-232 Management Procedure SummaryRS-232 Management Requirements Set Up Terminal Program Connect RS-232 Cable to Access NavigatorObtain Information Start RS-232 Management Session Perform Management Operations Exit RS-232 Management Session Telnet Management Telnet Management Requirements Start Telnet Program and Connect to Access Navigator Start Telnet Management Session Exit Telnet Management Session When Finished NetworkValet EMS and Valet Management Start Management Session Provision Access Navigator Provision Access Navigator CLI Commands DescriptionsBasic Provisioning Overview Basic Provisioning Quick Guide Obtain Provisioning Information Verify System Equipment Configuration Set System ID or Clli Code Show id Set Date Set TimeShow date Show time Set Ethernet Properties Set ethernet ip address none Set User and Password Security Set user Alice password Set Snmp Properties DNVRCO1A201 Example Set snmp nms 1 Provision DCS Service Provision DCS Service DCS Provisioning Overview Provisioning Isdn BRI Service Provisioning TR-08 Service with DCS Provisioning Conventional TR-08 Voice Services Provisioning Voice Services for TR-08 Shelves B, C, and D Provisioning Enhanced Voice and Data Services Special TR-08 Settings DCS Provisioning Quick Guide Card not installed Verify Service Status Show ds1 all Status ds1 n Set Unused Circuits Out of Service Set ds1 n down Set ds0 nch type voicedata Set System Clock Source Provision Groom DS1 Circuits to Network CAC Example Set ds1 10 loopdetect on Test Groom DS1 Circuits Provision Drop DS1 Circuits to Subscribers Set ds1 20 framing esf Provision and Connect Isdn PRI Channels Provision and Connect Isdn BRI 3DS0 Channels Provision and Connect DS0s DS0 #10 Test DS1 and DS0 Circuits Turn Up ServiceSet ds1 n up set ds0 nch up Test DS1 and DS0 Circuits Provision GR-303 Service Provision GR-303 Service GR-303 Provisioning Overview Access Navigator GR-303 Services Provisioning P-Phone Service Provisioning TR-08 Service with GR-303 Translation Provisioning TR-08 Service to Access Banks TR-08 Configuration Signaling TranslationSpecial Pots Cards CRV Numbering Set ds0 49-16 crv Set ds0 41-24 crv 311-334 slc96 Access Bank I/TR-08 Switch Settings Framing and FDL SettingsSwitch Shelf Access Bank I/TR-08 Loopback Code Response GR-303 Provisioning Quick Guide Connect Isdn D channel to Switch Set DS0s in serviceSet DS1s in service Isdn BRI 41 TDM channels Access Navigator Release August 10-11 10-12 Set ds1 n down set ds0 nch down Set System Switch Type Show switch Provision Switch DS1s to Interface Group 10-16 Access Navigator Release August 10-17 Assign Primary and Secondary EOC Assign Primary and Secondary TMC Set tmc primary nchnone Test DS1 Circuits Provision Drop DS1 Circuits to Subscriber Set ds1 n framing d4esfslc96 Example Set ds1 Fdl none Fdl t1403 10-24 Provision Isdn BRI 41 TDM Service to Subscribers CRV Send switch provision request Show isdn database 10-28 Access Navigator Release August 10-29 Provision DS0s to Subscribers Set ds0 nch type gr303 Assign Call Reference Values CRVs Example Set ds0 21-4 crv Test Circuits Provision Remote Access Bank Remote Access Bank II Provisioning Overview Provision Remote Access Bank Pre-Provisioning and Testing Requirements Crossconnect Features Analog Interfaces Valid Crossconnect Assignments Crossconnections Abii FX Interfaces Support Analog Voice and Data Services FX Analog Interfaces Valid Interface Assignments Fractional InterfacesInterface Type DS1 Type DS0 Type Voice Data GR-303 Remote Interfaces Remote Access Bank II Provisioning Quick Guide Remote Access Bank II Maintenance Quick Guide DS1 Card Installed Card not installed 11-12 Access Navigator Release August 11-13 Temporarily Disable Configuration Downloading Provision Drop DS1 to Remote Access Bank Set ds1 n remote device management cafdl Provision DS0s Set ds0 nch type voicedatagr303 Provision DS0 Crossconnects Example connect 2519-24 Create Fractional Interfaces if required Configure Remote RS-232 Interface if used Set baud rate with the following command Configure Remote T1 Drop Interface if used Set remote n t1drop linecode amib8zs Set remote n t1drop lbo settingSet remote n t1drop prm ansiatt Configure Remote V.35 Interface if used Set remote n v35 clkinv rxtxrxtxnone Download Configuration to Remote Access Bank Connect Fractional Interface to Remote Interface Verify Downloaded Settings optional Test Remote Circuits Call Status FX and Spots To Loop or Provision Remote Adit 600 via FDL Remote Adit 600 FDL Provisioning Overview Provision Remote Adit 600 via FDL FDL Management Configuration On-Net Customer Location Premises Remote Adit 600 FDL Provisioning Quick Guide Provision Remote Adit 600 via FDL Set Verify Equipment Configuration Access Navigator Release August 12-7 CA FDL Status remote nall Interface Provision Drop DS1s to Remote Adit Set ds1 n linecode amib8zs 12-12 Provision Drop DS0s Set ds0 nch signal lsgsem Set ds0 nch up Example set ds0 101-24 up Provision DS0 Crossconnects if required Crossconnect Examples Provision Remote Adit Logon remote n 12-18 Provision Remote Adit 600 via IP DS0 Remote IP DS0 Provisioning Overview Provision Remote Adit 600 via IP DS0 IP DS0 Management Configuration Carrier Access IP DS0 Management Configuration Access Navigator CLI Commands Descriptions Remote IP DS0 Provisioning Quick Guide Adit CLI Commands Descriptions Router SetupRouter Provisioning Quick Guide Verify status of management channel Select the PVC Management as Disabled Set Device Name to Adit1 Remote Adit IP DS0 Provisioning Quick Guide 13-8 Access Navigator Release August 13-9 13-10 Out of Service Provision Groom DS1s to Adit Router Set ds1 32 framing esf 13-14 Access Navigator Release August 13-15 Set ds1 n framing d4esf Set ds1 n remote device management caip ipaddr pphone Set DS1 identification Provision Groom DS0s to Adit Router Provision Drop DS0s to Remote Adit 13-20 Access Navigator Release August 13-21 13-22 Access Navigator Release August 13-23 13-24 Alarm Clearing Alarm Clearing Identify Alarm Clearing ProcedureFacility Alarm System go to Clear Alarms FDL on Clear Alarms FDL CLI Critical Alarm Message and Trouble Clearing ProcedureEvent Message Description Trouble Clearing Procedure Set alarms critical off CLI Major Alarm Message and Trouble Clearing Procedure Set ds1 n updown CLI Minor Alarm Message and Trouble Clearing Procedure Card Software on Status eoc Show eoc Status tmc Show tmc Clear Alarms EOC EOC Critical Alarm Message and Trouble Clearing Procedure EOC Major Alarm Message and Trouble Clearing Procedure EOC Minor Alarm Message and Trouble Clearing Procedure Active 14-12 EOC Warning Alarm Message and Trouble Clearing Procedure Switch Trap Message and Trouble Clearing Procedure Clear Alarms SnmpTrap Message Description Trouble Clearing Procedure Clear Alarms Status Indicators Alarm Indicators Power Status LEDs Power Status LEDsLED State Description Troubleshooting Status equipment command for System, use the switch controllerActive/Standby Controller Status LEDs 10. Active/Standby Controller Status LEDs Critical Alarm Status LEDs Major Alarm Status LEDs11. Critical Alarm Status LEDs 12. Major Alarm Status LEDs Minor Alarm Status LEDs Alarm Cutoff ACO Status LED13. Minor Alarm Status LEDs 14. Alarm Cutoff ACO Status LEDs DS1 Status LEDs Set ds1 up command15. DS1 Status LEDs Ethernet Link Status LED 16. Ethernet Link Status LED 14-22 Diagnostics & Troubleshooting Diagnostics & Troubleshooting Alarms and LogsOperations Interface Alarm Reporting Alarm TestingAlarm and Status Indicators Syntax set alarms criticalmajorminor onoff Alarm Cutoff ACO Facility Alarm SystemAlarm Signaling Red, Yellow RAI, Blue AIS Event Log DS1 FailuresSyntax log majorminoralertinfo Configuration Change Log Bert Log TMC LogSyntax clear bert log Syntax log tmc permanent Alarm and Status Indicators Indicator Locations Rear Panel Ethernet Indicator Indicator Descriptions Indicator DescriptionsState Description Green Status Clock Status and PerformanceSyntax status clock Syntax status ds0 nch Status DS0Example status ds0 Status DS1 Syntax status ds1 nField Description Example status ds1 Status DS1 All Syntax status ds1 all Access Navigator Release August 15-15 Syntax status ds1 n performance Status DS1 PerformanceExample status ds1 9 performance Syntax status ds1 n performance history Status DS1 Performance HistoryExample status ds1 9 performance history Clear DS1 Performance Syntax clear ds1 n performance Status Equipment Syntax status equipment Status IP Syntax status ip Status Remote Syntax status remote nallField Example status remote all GR-303 Status and Performance Status CRVSyntax status crv range Example status crv Syntax status isdn crv range Status Isdn CRVExample status isdn crv 15-24 Status EOC Status TMCSyntax status eoc Syntax status tmc Originating Calls Blocked Calls Secondary Syntax status tmc allinterval Status TMC HistoryExample status tmc all Clear Blocked Call Count Clear Peak Call CountClear Permanent Call Count Set CRV Idle Near-End Loopbacks DS1 LoopdetectDS1 FDL Protocol Syntax set ds1 n loopdetect onoff DS1 Line Loopback DS1 Payload LoopbackSyntax set ds1 n line loopdownloopup Syntax set ds1 n payload loopdownloopup DS1 CSU Loopup Far-End LoopbacksSyntax send ds1 n csu loopuploopdown DS1 Line Loopup Syntax send ds1 n line loopuploopdown DS1 Network Loopup Syntax send ds1 n network loopuploopdown DS1 NIU Loopup Syntax send ds1 n niu loopuploopdown DS1 Payload Loopup Syntax send ds1 n payload loopuploopdown Access Bank II Loopbacks Read Remote LoopbackSend Remote Loopdown Syntax read remote n loopback Send Remote RS232 Line Loopup Send Remote RS232 TSI Equipment LoopupSyntax send remote n rs232 line loopup Syntax send remote 9 rs232 tsi equipment loopup Send Remote RS232 TSI Network Loopup Send Remote Sdsl Payload LoopupSyntax send remote 9 rs232 tsi network loopup Syntax send remote n sdsl payload loopup Send Remote T1 Payload Loopup Send Remote T1 TSI LoopupSyntax send remote n t1 payload loopup Syntax send remote n t1 tsi loopup Send Remote T1 Drop Line Loopup Send Remote T1 Drop Payload LoopupSyntax send remote n t1drop line loopup Syntax send remote n t1drop payload loopup Syntax send remote n t1drop tsi loopup Send Remote V35 Line LoopupSyntax send remote n v35 line loopup Send Remote V35 TSI Equipment Loopup Send Remote V35 TSI Network LoopupSyntax send remote n v35 tsi equipment loopup Syntax send remote n v35 tsi network loopup Bit Patterns and Error Tests Send DS1 Pattern OffSend DS1 Line Pattern Syntax send ds1 n off Send DS1 Payload Pattern Syntax send ds1 n line p2e11p2e15p2e23qrss Access Navigator Payload Code Send DS1 Line Pattern with BER Test Syntax send ds1 n line p2e11p2e15p2e23qrss test Example set ds1 9 line p2e15 test FBE Send DS1 Payload Pattern with BER Test 26. Send DS1 Payload Pattern with BER Test Example send ds1 9 payload p2e15 test Example Test 15-52 Other Maintenance Commands Show users Load tftp config ipaddr fileWhoami Technical Support Show isdn database show crv database Trace tmc on Let run for 2 or 3 minutesTrace tmc off Trace eoc Trace eoc Off Maintenance Procedures Repair and Return Procedure Maintenance Procedures Replace Controller Card Overview Tools and Materials Required Determine Which Replacement Procedure to Use Verify Equipment Status Precautions Procedure SummaryReplace Protected Controller Card Verify Compatibility Remove Front Cover Replace Standby Controller Location of Controller Cards Installing and Removing Controller Card Verify Operation and Compatibility Replace Other Controller Card Replace Unprotected Controller Card Controller B Active DS1 Card Installed Access Navigator Release August 16-15 Insert New Controller Access Navigator Release August 16-17 Remove Old Controller Overview Replace Quad T1 Framer CardQF Card Slot DS1 Circuit Numbers Tools and Materials Required Verify Equipment Status Temporarily Move Clock Sources if requiredSet clock1 ds1 n Set clock2 ds1 n Location of Front Panel Cover Screws Replace Quad T1 Card 10. Location of Quad T1 Framer Cards 11. Installing Quad T1 Framer Card Verify Operation 12. Location of Front DS-1 Status Indicators Restore Clock Sources if required Show clock Install Simm on Controller Card Precautions Tools and Materials Required 16-30 Standby Controller ACTIVE/STANDBY indicator is off 14. Location of Front Panel Cover Screws Install Simm 15. Location of Controller Cards Simm Access Navigator Release August 16-35 16-36 Update Controller Card Software Download Procedures Update Controller Card Software Tftp Requirements Update Software via Tftp Two ControllersEvent Log 17-4 Install Optional Tftp Server Software Information and Materials Required Status equipment all Requirement One Controller is in Standby Upload Configuration Verify IP Connectivity Download Software Set ds0 321 up set ds0 321 down Show ds0Set ds0 321 down set ds0 321 up Download Configuration Example load tftp config 192.168.118.65 AN26 Update Software via Xmodem Two Controllers Xmodem Requirements 17-12 Access Navigator Release August 17-13 System Access Navigator Release August 17-15 17-16 Update Software via Xmodem One Controller 17-18 SW Build Number 17701 Boot Code Revision 01.09 Minutes Access Navigator Release August 17-21 17-22 CLI Language Reference CLI Access Via RS-232 and Telnet CLI Language Reference Port settings CLI RequirementsCLI over RS-232 Terminal emulation Access Navigator IP address CLI over TelnetRS-232 interface for modem connection Ethernet interface Character and Line Delays Using CLI Command ScriptsConfirmations and Errors Command Categories Commands, Confirmations, and Error MessagesCLI Conventions and Shortcuts SystemID set ds1 24 framing esf SystemID set ds1 42 framing esf Text ConventionsSet ds1 1-4 up Command Syntax Descriptions Entering DS1 and DS0 Numbers and Ranges Command Shortcuts TabbingKeyboard Shortcuts Online Help Displaying Basic CommandsHelp System Overview Context Sensitive Help 18-12 Printing the Help File Syntax print help Users and Passwords AdministrationAccess Levels User Level Access Managing Users Who AmShow Users Syntax show users Add User Set User Access LevelSyntax add user name Example add user alice Set User Password Delete User PasswordAccess Definition Delete User Logging In and Out Login with No User Name RequiredStartup Message Login with No Password Required Login with User Name RequiredLogin with Password Required Autoexit CLI Session Timeout Logout ExitSyntax set autoexit minutes Example set autoexit CLI Command List ACO CLI Language Reference ACO Add Interface Remote Port Maximum Number of DS0s Type Description Syntax alarms majorminoralert AlarmsSyntax add user name Syntax alarms ds1 nall Syntax alarms ds1 nall majorminoralertSyntax alarms equipment Syntax alarms equipment majorminoralert Clear Config Log Clear Bert LogClear Blocked Call Count Clear DS1 Performance Clear Log Clear Peak Call CountClear Permanent Call Count Clear Remote Log Connect Example connect 2519-24 18-30 Connect Remote Interface Drop Groom SwitchDrop Delete Interface Syntax connect remote name fxrs232sdslt1dropv35Syntax delete interface name Example delete interface AcmeV35 Disconnect Syntax delete user nameSyntax disconnect nch Example disconnect Disconnect Remote ExitExit Remote Session Ctrl+C Syntax disconnect remote name Load Xmodem Active Load Tftp Config Example load tftp config 192.168.118.65 AN26 Log Example log Message Example log equipment minor Log Bert Log Config Example log config ds0 Example log config Description Log TMC Example log tmc Message Syntax logon remote n Logon RemoteExample logon remote Read Remote Alarms Syntax read remote n alarmsExample read remote 9 alarms Ping 18-46 Access Navigator Release August 18-47 Syntax read remote n connections Read Remote ConnectionsExample read remote 9 connections Access Navigator Release August 18-49 Syntax read remote n log Read Remote LogExample read remote 9 log Read Remote Loopback Read Remote RS232Example read remote 9 loopback Syntax read remote n rs232 Read Remote Performance Syntax read remote n t1t1drop performance Access Navigator Release August 18-53 Read Remote T1 Syntax read remote n t1 Read Remote T1drop Level 3 monitorRead remote Read remote T1drop Syntax read remote n Read RemoteExample read remote 9 Reset All Reset DS1 FramerSyntax reset all Syntax reset ds1 n Reset Remote Reset StandbySyntax reset remote n Example reset remote Restore Defaults Default SettingsSyntax restore defaults Parameter Default Comments Normal CLI Language Reference Send DS1 CSU Loopup Line loopback deactivate Example send ds1 9 csu loopup Send DS1 Line LoopupExample send ds1 9 csu loopdown 00001110 11111111 Example send ds1 9 line loopup Send DS1 Line patternExample send ds1 9 line loopdown Send DS1 Line Pattern Send DS1 Line pattern Test Example set ds1 9 line p2e15 Send DS1 Line Pattern with BER Test Access Navigator Release August 18-69 Send DS1 Network Loopup Send DS1 Network Loopup Example send ds1 9 network loopup Send DS1 NIU LoopupExample send ds1 9 network loopdown Syntax send ds1 n niu loopup loopdown Example send ds1 9 niu loopup Send DS1 Payload Loopup Example send ds1 9 niu loopdown Example send ds1 9 payload loopup Example send ds1 9 payload loopdown Send DS1 Payload pattern 10. Send DS1 Payload Pattern Send DS1 Payload pattern Test Example send ds1 9 payload p2e15 11. Send DS1 Payload Pattern with BER Test Example set ds1 9 payload p2e15 test P2e11 Example send ds1 9 payload f1in8 test Send DS1 Off Send Remote LoopdownExample send ds1 9 off Example send remote 9 loopdown Send Remote RS232 Line Loopup Example send remote 9 rs232 line loopup Send Remote RS232 TSI Loopup Send Remote Sdsl Payload Loopup Syntax send remote n rs232 tsi equipmentnetwork loopup Send Remote T1 Payload Loopup Example send remote 9 sdsl payload loopup Send Remote T1 TSI Loopup Example send remote 9 t1 payload loopup Remote loopdown command Example send remote 9 t1 tsi loopup Send Remote T1Drop Line Loopup Example send remote 9 t1drop line loopup Send Remote T1Drop Payload Loopup Send Remote T1Drop TSI Loopup Example send remote 9 t1drop payload loopup Send Remote V35 Line Loopup Example send remote 9 t1drop tsi loopup 21. Remote V.35 Line Loopup Example send remote 9 v35 line loopup Send Remote V35 TSI Loopup Syntax send switch provision request Send Switch Provision RequestSyntax send remote n v35 tsi equipmentnetwork loopup Example set alarms major on Set AlarmsSet Autoexit Setting Description Syntax set clock1clock2 settingSet Clock Set Date Set CRV IdleSet DS0 CRV Syntax set ds0 nch crv range slc96 Ds0 49-16 Crv 111-118 513 crvDs0 41-24 Crv 311-323 26. DS0s Assigned to CRVs in Odd-Even Order Set DS0 Isdn BRI CRV Syntax set ds0 nch isdn none Set DS0 P-Phone Syntax set ds0 nch pphone Syntax set ds0 nch pphone none Syntax set ds0 nch updown Set DS0 ServiceExample set ds0 131-16 up Set DS0 Signal Syntax set ds0 nch signal didemgsgshrgls 27. Signaling Used in Common Applications Set DS0 Type Set DS1 FDL Set DS1 ClockSyntax set ds0 nch type datavoicegr303 Application Configuration Requirements Permissible SelectionsApplication Framing Set DS1 Framing Example set ds1 12 fdl none Example set ds1 12 fdl t1403Syntax set ds1 n framing d4esfslc96 Example set ds1 9 framing esf Set DS1 LBO Set DS1 IDSet DS1 Line Loopup Set DS1 Linecode Example set ds1 9 line loopdownSyntax set ds1 n linecode amib8zs Example set ds1 9 linecode b8zs Set DS1 Loopdetect Example set ds1 9 loopdetect off Syntax set ds1 n payload loopuploopdown Set DS1 Payload LoopupExample set ds1 9 payload loopdown Set DS1 Remote Device Mgmt Example set ds1Mgmt ds1 Mgmt caip Set DS1 Service Set DS1 TermIDSyntax set ds1 n updown Example set ds1 9 up Syntax set ds1 n termid id Set DS1 ThresholdExample set ds1 5 termid Set DS1 Type Syntax set ds1 n type dropgroomswitchSet EOC Syntax set eoc primarysecondary nchnone Set Ethernet IP AddressSyntax set ethernet ip address address mask Set IP Gateway Address Set IDExample set id Acme Corp. AN#2 Example set id DNVRCO1A201 Syntax set ip gateway address Set Remote ConfigExample set ip gateway Example set ip gateway none Set Remote ID Set Remote RS232 Baud Set Remote RS232 Data Set Remote RS232 Stop Syntax set remote n t1drop framing d4esf Set Remote T1Drop FramingExample set remote 9 t1drop framing d4 Set Remote T1Drop LBO Set Remote T1Drop Linecode Set Remote T1Drop PRM Set Remote V35 ClockInv Set Remote V35 CTS Set Remote V35 Data Set Remote V35 RxClock Set Remote V35 DSUSet Remote V35 Speed Set Screen Syntax set remote n v35 speedExample set remote 9 v35 speed nx64 Syntax set screen heightoff Set Snmp Contact Set Snmp GetCom Set Snmp Location Set Snmp Name Set Snmp NMS Address Set Snmp SetCom Set Switch Type Set Snmp TrapCom Set Time Set TMCSyntax set time hhmmss Example set time Syntax set user name level access Set User Level Syntax set user name password Show Autoexit Show ClockShow Connect Syntax show autoexit Syntax show connect n Example show connect Syntax show crv range Show CRVExample show crv 30. Factory Default Call Reference Values Show Date Show DS0Syntax show date Syntax show ds0 nch Syntax show ds1 n Show DS1Example show ds1 Access Navigator Release August 18-141 Performance Description Thresholds Remote Device Mgmt on Show DS1 All Syntax show ds1 all 18-144 Show Ethernet Show EOCSyntax show ethernet Show ID Show Interface Syntax show interface nameall Example show interface AcmeT1 Example show interface all Show IP Show Isdn CRV Syntax show isdn crv range Example show isdn crv Syntax show remote nall Show RemoteExample show remote Example show remote all Syntax show remote n connections Show Remote ConnectionsExample show remote 9 connections 18-152 Show Snmp Syntax show snmp Show Switch Switch Setting DescriptionShow Time Show TMC Access Navigator Release August 18-155 Status Clock Status CRV Status DS0 Status DS1 18-160 Status DS1 All Status DS1 Performance Access Navigator Release August 18-163 18-164 Status DS1 Performance History UAS Status EOC Status Equipment Syntax status equipment all Example status equipment Example status equipment all Status IP Status Isdn CRV Status Remote Status TMC Pots Status TMC History Syntax status tmc allintervalrange Upload Tftp Config Switch ControllerSyntax switch controller Example upload tftp config 192.168.118.65 CAN26 WhoAmI 18-178 Appendix EOC Interface Remote Digital Customer Premises Terminal RDT Access Navigator Release August Alarm Count List Objects on page A-5 Managed Object Class Support Alarm Count List Objects Table A-2 Alarm Count List ObjectsAttribute Support Command Support Create Get Set Delete Analog Line Termination Objects DS0 Channel Termination Objects DS1 Framed Path Termination ObjectsTable A-3 DS0 Channel Termination Objects Table A-4 DS1 Framed Path Termination Objects DS1 Line Termination Objects EBS Line Termination ObjectsTable A-5 DS1 Line Termination Objects Table A-6 DS1 Line Termination Objects Isdn Line Termination Objects Isdn Framed Path Termination ObjectsTable A-7 Isdn Line Termination Objects Table A-8 Isdn Framed Path Termination Objects Isdn Framed Path Termination Objects Quarter DS0 Channel Termination CrossconnectionTable A-9 Isdn Framed Path Termination Objects Table A-10 Crossconnection Equipment Objects Idlc Call Processing Profile ObjectsTable A-11 Equipment Objects Table A-12 Idlc Call Processing Profile Objects Idlc Data Link Profile Objects Table A-13 Idlc Data Link Profile Objects Idlc Data Link Termination Objects Table A-14 Idlc Data Link Termination Objects Idlc Terminal Objects Memory ObjectsTable A-15 Idlc Terminal Objects Table A-16 Memory Objects Network Element Objects Protection Group ObjectsTable A-17 Network Element Objects Table A-18 Protection Group Objects Protection Group Unit Objects Table A-19 Protection Group Unit Objects Table A-20 Action Support ActionsManaged Object Class Action Support Table A-21 Event Report Notification NotificationsManaged Object Class Event Report Notification FDL Interface FDL Interface Figure B-1. FDL Interface Access Navigator Remote Provisioning Requirements Access Bank II Remote Provisioning RequirementsRemote Provisioning Requirements Adit 600 TDM Remote Provisioning Requirements Access Bank II Capabilities Access Bank II CapabilitiesInterface Capabilities and Settings Remote Provisioning Capabilities RTS FDL Interface Snmp Interface Snmp Interface Operations Location Center Carrier Access Enterprise MIB Figure C-2. Carrier Access Enterprise MIB top level Snmp Basics MIB Structure Table C-1.Standard Snmp Object Types MIB TablesObject Type Description Table C-2 Standard Snmp Messages Managing NetworksMessage Type Description Snmp Protocols Table C-3 Snmp Configuration Items Snmp Requirements Snmp Trap Reports Table C-4 Standard Snmp Trap ReportsTable C-5 Enterprise Snmp Trap Reports Trap Description Test Method Snmp Interface Glossary Glossary LTE Lult Definitions Page Identifier Access Navigator Release August GlossaryGlossary-7 Electronic Business Set Or Service Access Navigator Release August GlossaryGlossary-9 Multiplex POP RAI Stratum Wide Area Network Wideband GlossaryGlossaryGlossaryGlossary-14 August Index Index EOC Access Navigator Release August Index CPE DLC LED FXO TMC LAN T1 TSI MIB Index PRI Sdsl DS1 CRV Isdn BRI CRV Phone Service Signal Type DSU SPR Tftp TSI Index Index