Manuals / Carrier Access / Computer Equipment / Network Router

Carrier Access Access Navigator Install Additional Quad T1 Framer Cards, Installation Summary

Models: Access Navigator

1 704

Download 704 pages 57.28 Kb

Page 159

Electrical Installation

Install Additional Quad T1 Framer Cards

Install Additional Quad T1 Framer Cards

This procedure provides steps for installing additional Quad T1 Framer (QF) cards to increase DS1 service capacity. Steps are also included to very operation after installation. The Access Navigator can hold up to eight QF cards, providing a total of 32 DS1 circuits. QF cards are hot swappable and can be installed at any time, without interrupting service on other cards.

Installation Summary

Precautions ... 6-55

Tools and Materials ... 6-55

Remove Front Cover ... 6-56

Install Quad T1 Framer Card ... 6-57

Verify Operation ... 6-59

Replace Front Cover ... 6-61

Precautions

DANGER! BURN HAZARD. CHASSIS, COVER SCREWS, AND CARDS MAY BE HOT TO THE TOUCH.

WARNING! THE ACCESS NAVIGATOR CONTAINS CIRCUIT CARDS AND COMPO- NENTS THAT ARE SUBJECT TO DAMAGE BY ELECTROSTATIC DISCHARGE (ESD). ALWAYS FOLLOW THE STATIC-SENSITIVEEQUIPMENT HANDLING PROCEDURES ON page 6-3WHEN OPENING EQUIPMENT COVERS AND HANDLING PLUG-IN CIRCUIT CARDS.

Tools and Materials

Obtain the following tools and materials.

•Office records for installation site

•Grounding wrist strap

Access Navigator - Release 1.8

August 2003

6-55

Image 159

Carrier Access Access Navigator user manual Install Additional Quad T1 Framer Cards, Installation Summary

Contents

Access Navigator Mailtech-support@carrieraccess.com Preface Preface ComplianceElectrostatic Discharge ESD Precautions Carrier Access Software License Agreement LicenseTitle and Risk Disclaimer WarrantyCopyright TermJurisdiction and Venue Limitations of Warranty & Limitation of Remedies WarrantyFollow Electrostatic Discharge ESD Precautions on Warranty Product ReturnsTable of Contents Table of Contents Access Navigator / GR-303 + Data HostAccess Navigator / GR-303 Host with P-Phone Electrical Installation Physical Installation1xv 1xvi August Access Navigator Release Provision Access Navigator Provision DCS ServiceStart Management Session Provision Remote Access Bank Provision GR-303 ServiceProvision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via FDLDiagnostics & Troubleshooting Alarm Clearing1xxi Update Controller Card Software Maintenance ProceduresCLI Language Reference 1xxiv August Access Navigator Release 1xxv 1xxvi August Access Navigator Release EOC Interface Index FDL InterfaceSnmp Interface GlossaryChapter Introduction OverviewAccess Navigator Configurations Features and BenefitsSystem Architecture Access Navigator System ArchitectureCarrier Access Support Products Access BanksAdit Management Command Line InterfaceSnmp Valet and NetworkValet EMS Software Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Access Navigator / DCS Service ManagerSwitch Center Co-location Customer Premises Management ServicesFunctions FacilitiesNetwork Quad T1 Framer Card Features Controller Card Features ConfigurationDCS Operation SpecificationsApplications InterfacesManagement Interfaces SignalingAlarms System ClockingPhysical PowerCompliance EnvironmentalPart Compliance RequirementsFCC Requirements Part 15, Class aFacility Interface Codes FIC Service Order Codes SOCTelcordia Bellcore Requirements UL RequirementsOrdering Information CSA RequirementsPart Number Description Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data HostGR-303 Ethernet RS-232 Modem Voice GR-303 Services Lines Management Key System Access Navigator Data Host Architecture DCS ServicesIP DS0 Management Management ArchitectureFDL Management Access Navigator FDL Management ArchitectureGR-303 call support Applications Crossconnects GR-303 OperationDCS Signaling GR-303 SignalingCompliance Compliance Requirements Telcordia Bellcore Requirements Ordering Information Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-PhoneAccess Navigator / GR-303 with P-Phone Architecture Features and Benefits Voice Fax P-Phone Service Support Using Adit 600 Terminals Phone ServicesDCS Services Management Architecture FDL Management Configuration Applications Specifications GR-303 Signaling Standards Compliance Requirements Telcordia Bellcore Requirements Ordering Information Ordering Information Physical Installation Physical Installation Compliance and Safety RequirementsUnpacking and Inspection Tools and MaterialsInstallation Summary Precautions Tools and MaterialsHorizontal 19-Inch Rack Mount Attach Access Navigator to Equipment Rack Attach Mounting Brackets to Access NavigatorMounting Four per side Bracket Fasten brackets to Horizontal 23-Inch Rack Mount Assemble Mounting Brackets Installation in 23-inch Equipment Rack Inches minimum Vertical Rack Mount Using Crossbars Attach Access Navigator to Crossbars Install CrossbarsCrossbar Installation Inch Equipment Rack Vertical Wall Mount PrecautionsPrepare Plywood Ensure Adequate ClearanceAttach Access Navigator to Plywood Wall View Wire Tie Plywood Sheet Inches Minimum 12. Mounting Hole Pattern on Plywood 13. Wall Mount Bracket Installation Physical Installation Electrical Installation Electrical Installation Static-Sensitive Equipment Handling Procedures Tools and Materials Required Chassis Ground Connection Connect Ground Wire to Ground Lug Run Ground Wire to Access NavigatorAttach Ground Lug to Access Navigator DSX-1 Cable Connections Prepare DSX-1 Cables CAC Location of Rear Panel DS1 Connectors Connect DSX-1 Cables to Access NavigatorElectrical Installation Attaching Ferrite Bead RF Suppressors Attach Ferrite BeadsConnect DSX-1 Cables to Interface or Patch Panel Card Group DSX-1 Cable Pin Connections and Flying Wire ColorsElectrical Installation Information, Tools, and Materials RS-232 Management ConnectionRS-232 DTE-to-DCE Cable RS-232 DCE-to-DCE Modem Cable Connections Connect Shielded RS-232 Cable10. Attaching Ferrite Bead RF Suppressor Attach Ferrite Bead RF SuppressorPreconfigure Optional Modem Ethernet Management Connection Information and MaterialsMake Ethernet Cable Optional MDI Port Pins Signals Connect Ethernet Cable to Ethernet Hub Connect Ethernet Cable to Access NavigatorExternal Timing Source Bits Connection Connect Bits Cable Make Bits Cable OptionalAlarm Output Connections 15. Alarm Output Connector Wire Alarm Output ConnectorMaximum 18. Location of Rear Panel Alarm Output Connector Plug Output Alarm Connector into Access NavigatorAlarm Input Connections 19. Alarm Input Connector Wire Alarm Input ConnectorCable Shield 22. Location of Rear Panel Alarm Input Connector Plug Alarm Input Connector into Access NavigatorDC Power Connections Used Wire Power ConnectorsConnect Power Plugs to Access Navigator Verify WiringDress Cables and Wires Dress Cables and WiresVerification Summary Acceptance Test26. Location of Front Panel Power-On Status LEDs Apply Power and Verify OperationVerify DSX-1 Connections Verify Chassis Ground ConnectionVerify RS-232 Management Connection Verify Ethernet Management Connection Verify Ethernet Cable ConnectionSet clock1 bits set clock2 bits Verify Bits ConnectionController ’A’ Indicators Controller ’B’ Indicators Verify Alarm Output ConnectionsElectrical Installation 31. Location of Rear Panel Alarm Input Connector Verify Alarm Input ConnectionsExit Exit Management SessionInstall Redundant Controller Card Verify Software Compatibility 33. Location of Front Panel Cover Screws Remove Front Cover34. Location of Controller Cards Install Controller CardVerify Operation Switch controllerReplace Front Cover Install Additional Quad T1 Framer Cards 37. Location of Front Panel Cover Screws 38. Location of Quad T1 Framer Cards Install Quad T1 Framer CardEject Set ds1 n up Status equipmentSet ds1 n down 29-32 13-16 17-20 21-24 26-28Configure Management Interfaces Setup SummaryReplace Front Cover Start RS-232 Management Session Set Time Set DateSet IP Address and Subnet Mask Set System ID or Clli codeSet Gateway Address Exit Management Session Start Management Session Start Management Session Management RequirementsShow ds1 Command Line Interface ConventionsProcedure Summary RS-232 ManagementRS-232 Management Requirements Connect RS-232 Cable to Access Navigator Set Up Terminal ProgramObtain Information Start RS-232 Management Session Exit RS-232 Management Session Perform Management OperationsTelnet Management Requirements Telnet ManagementStart Telnet Management Session Start Telnet Program and Connect to Access NavigatorExit Telnet Management Session When Finished NetworkValet EMS and Valet Management Start Management Session Provision Access Navigator Basic Provisioning Quick Guide Provision Access NavigatorCLI Commands Descriptions Basic Provisioning OverviewObtain Provisioning Information Verify System Equipment Configuration Show id Set System ID or Clli CodeShow time Set DateSet Time Show dateSet Ethernet Properties Set ethernet ip address none Set User and Password Security Set user Alice password DNVRCO1A201 Set Snmp PropertiesExample Set snmp nms 1 Provision DCS Service DCS Provisioning Overview Provision DCS ServiceProvisioning TR-08 Service with DCS Provisioning Isdn BRI ServiceProvisioning Voice Services for TR-08 Shelves B, C, and D Provisioning Conventional TR-08 Voice ServicesSpecial TR-08 Settings Provisioning Enhanced Voice and Data ServicesDCS Provisioning Quick Guide Card not installed Show ds1 all Verify Service StatusStatus ds1 n Set ds1 n down Set ds0 nch type voicedata Set Unused Circuits Out of ServiceSet System Clock Source CAC Provision Groom DS1 Circuits to NetworkExample Set ds1 10 loopdetect on Provision Drop DS1 Circuits to Subscribers Test Groom DS1 CircuitsSet ds1 20 framing esf Provision and Connect Isdn BRI 3DS0 Channels Provision and Connect Isdn PRI ChannelsProvision and Connect DS0s DS0 #10 Turn Up Service Test DS1 and DS0 CircuitsSet ds1 n up set ds0 nch up Test DS1 and DS0 Circuits Provision GR-303 Service GR-303 Provisioning Overview Provision GR-303 ServiceAccess Navigator GR-303 Services Provisioning P-Phone Service Provisioning TR-08 Service to Access Banks Provisioning TR-08 Service with GR-303 TranslationCRV Numbering TR-08 ConfigurationSignaling Translation Special Pots CardsSet ds0 41-24 crv 311-334 slc96 Set ds0 49-16 crvFraming and FDL Settings Access Bank I/TR-08 Switch SettingsSwitch Shelf Access Bank I/TR-08 Loopback Code Response GR-303 Provisioning Quick Guide Isdn BRI 41 TDM channels Connect Isdn D channel to SwitchSet DS0s in service Set DS1s in serviceAccess Navigator Release August 10-11 10-12 Set ds1 n down set ds0 nch down Show switch Set System Switch TypeProvision Switch DS1s to Interface Group 10-16 Access Navigator Release August 10-17 Assign Primary and Secondary EOC Set tmc primary nchnone Assign Primary and Secondary TMCTest DS1 Circuits Provision Drop DS1 Circuits to Subscriber Set ds1 n framing d4esfslc96 Example Set ds1 Fdl none Fdl t1403 10-24 Provision Isdn BRI 41 TDM Service to Subscribers CRV Show isdn database Send switch provision request10-28 Access Navigator Release August 10-29 Provision DS0s to Subscribers Set ds0 nch type gr303 Assign Call Reference Values CRVs Example Set ds0 21-4 crv Test Circuits Provision Remote Access Bank Provision Remote Access Bank Remote Access Bank II Provisioning OverviewRequirements Pre-Provisioning and TestingAnalog Interfaces Crossconnect FeaturesCrossconnections Abii Valid Crossconnect AssignmentsFX Analog Interfaces FX Interfaces Support Analog Voice and Data ServicesFractional Interfaces Valid Interface AssignmentsInterface Type DS1 Type DS0 Type Voice Data GR-303 Remote Interfaces Remote Access Bank II Provisioning Quick Guide Remote Access Bank II Maintenance Quick Guide DS1 Card Installed Card not installed 11-12 Access Navigator Release August 11-13 Temporarily Disable Configuration Downloading Provision Drop DS1 to Remote Access Bank Set ds1 n remote device management cafdl Provision DS0s Set ds0 nch type voicedatagr303 Provision DS0 Crossconnects Example connect 2519-24 Create Fractional Interfaces if required Configure Remote RS-232 Interface if used Set baud rate with the following command Configure Remote T1 Drop Interface if used Set remote n t1drop lbo setting Set remote n t1drop linecode amib8zsSet remote n t1drop prm ansiatt Configure Remote V.35 Interface if used Set remote n v35 clkinv rxtxrxtxnone Connect Fractional Interface to Remote Interface Download Configuration to Remote Access BankVerify Downloaded Settings optional Call Status FX and Spots To Loop or Test Remote CircuitsProvision Remote Adit 600 via FDL Provision Remote Adit 600 via FDL Remote Adit 600 FDL Provisioning OverviewOn-Net Customer Location Premises FDL Management ConfigurationRemote Adit 600 FDL Provisioning Quick Guide Set Provision Remote Adit 600 via FDLVerify Equipment Configuration Access Navigator Release August 12-7 Status remote nall CA FDLInterface Provision Drop DS1s to Remote Adit Set ds1 n linecode amib8zs 12-12 Provision Drop DS0s Set ds0 nch up Example set ds0 101-24 up Set ds0 nch signal lsgsemProvision DS0 Crossconnects if required Crossconnect Examples Logon remote n Provision Remote Adit12-18 Provision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via IP DS0 Remote IP DS0 Provisioning OverviewCarrier Access IP DS0 Management Configuration IP DS0 Management ConfigurationRemote IP DS0 Provisioning Quick Guide Access Navigator CLI Commands DescriptionsVerify status of management channel Adit CLI Commands DescriptionsRouter Setup Router Provisioning Quick GuideSet Device Name to Adit1 Select the PVC Management as DisabledRemote Adit IP DS0 Provisioning Quick Guide 13-8 Access Navigator Release August 13-9 13-10 Out of Service Provision Groom DS1s to Adit Router Set ds1 32 framing esf 13-14 Access Navigator Release August 13-15 Set ds1 n remote device management caip ipaddr pphone Set ds1 n framing d4esfSet DS1 identification Provision Groom DS0s to Adit Router Provision Drop DS0s to Remote Adit 13-20 Access Navigator Release August 13-21 13-22 Access Navigator Release August 13-23 13-24 Alarm Clearing Identify Alarm Clearing Procedure Alarm ClearingFacility Alarm System go to Clear Alarms FDL on Set alarms critical off Clear Alarms FDLCLI Critical Alarm Message and Trouble Clearing Procedure Event Message Description Trouble Clearing ProcedureSet ds1 n updown CLI Major Alarm Message and Trouble Clearing ProcedureCard Software on CLI Minor Alarm Message and Trouble Clearing ProcedureShow eoc Status eocShow tmc Status tmcEOC Critical Alarm Message and Trouble Clearing Procedure Clear Alarms EOCEOC Major Alarm Message and Trouble Clearing Procedure EOC Minor Alarm Message and Trouble Clearing Procedure Active 14-12 Switch EOC Warning Alarm Message and Trouble Clearing ProcedureClear Alarms Snmp Trap Message and Trouble Clearing ProcedureTrap Message Description Trouble Clearing Procedure Alarm Indicators Clear Alarms Status IndicatorsPower Status LEDs Power Status LEDsLED State Description Troubleshooting 10. Active/Standby Controller Status LEDs Status equipment command forSystem, use the switch controller Active/Standby Controller Status LEDs12. Major Alarm Status LEDs Critical Alarm Status LEDsMajor Alarm Status LEDs 11. Critical Alarm Status LEDs14. Alarm Cutoff ACO Status LEDs Minor Alarm Status LEDsAlarm Cutoff ACO Status LED 13. Minor Alarm Status LEDsSet ds1 up command DS1 Status LEDs15. DS1 Status LEDs 16. Ethernet Link Status LED Ethernet Link Status LED14-22 Diagnostics & Troubleshooting Alarms and Logs Diagnostics & TroubleshootingOperations Interface Syntax set alarms criticalmajorminor onoff Alarm ReportingAlarm Testing Alarm and Status IndicatorsFacility Alarm System Alarm Cutoff ACOAlarm Signaling Red, Yellow RAI, Blue AIS DS1 Failures Event LogSyntax log majorminoralertinfo Configuration Change Log Syntax log tmc permanent Bert LogTMC Log Syntax clear bert logIndicator Locations Alarm and Status IndicatorsRear Panel Ethernet Indicator Green Indicator DescriptionsIndicator Descriptions State DescriptionStatus and Performance Status ClockSyntax status clock Status DS0 Syntax status ds0 nchExample status ds0 Example status ds1 Status DS1Syntax status ds1 n Field DescriptionSyntax status ds1 all Status DS1 AllAccess Navigator Release August 15-15 Status DS1 Performance Syntax status ds1 n performanceExample status ds1 9 performance Status DS1 Performance History Syntax status ds1 n performance historyExample status ds1 9 performance history Syntax clear ds1 n performance Clear DS1 PerformanceSyntax status equipment Status EquipmentSyntax status ip Status IPExample status remote all Status RemoteSyntax status remote nall FieldExample status crv GR-303 Status and PerformanceStatus CRV Syntax status crv rangeStatus Isdn CRV Syntax status isdn crv rangeExample status isdn crv 15-24 Syntax status tmc Status EOCStatus TMC Syntax status eocOriginating Calls Blocked Calls Secondary Status TMC History Syntax status tmc allintervalExample status tmc all Set CRV Idle Clear Blocked Call CountClear Peak Call Count Clear Permanent Call CountSyntax set ds1 n loopdetect onoff Near-End LoopbacksDS1 Loopdetect DS1 FDL ProtocolSyntax set ds1 n payload loopdownloopup DS1 Line LoopbackDS1 Payload Loopback Syntax set ds1 n line loopdownloopupFar-End Loopbacks DS1 CSU LoopupSyntax send ds1 n csu loopuploopdown Syntax send ds1 n line loopuploopdown DS1 Line LoopupSyntax send ds1 n network loopuploopdown DS1 Network LoopupSyntax send ds1 n niu loopuploopdown DS1 NIU LoopupSyntax send ds1 n payload loopuploopdown DS1 Payload LoopupSyntax read remote n loopback Access Bank II LoopbacksRead Remote Loopback Send Remote LoopdownSyntax send remote 9 rs232 tsi equipment loopup Send Remote RS232 Line LoopupSend Remote RS232 TSI Equipment Loopup Syntax send remote n rs232 line loopupSyntax send remote n sdsl payload loopup Send Remote RS232 TSI Network LoopupSend Remote Sdsl Payload Loopup Syntax send remote 9 rs232 tsi network loopupSyntax send remote n t1 tsi loopup Send Remote T1 Payload LoopupSend Remote T1 TSI Loopup Syntax send remote n t1 payload loopupSyntax send remote n t1drop payload loopup Send Remote T1 Drop Line LoopupSend Remote T1 Drop Payload Loopup Syntax send remote n t1drop line loopupSend Remote V35 Line Loopup Syntax send remote n t1drop tsi loopupSyntax send remote n v35 line loopup Syntax send remote n v35 tsi network loopup Send Remote V35 TSI Equipment LoopupSend Remote V35 TSI Network Loopup Syntax send remote n v35 tsi equipment loopupSyntax send ds1 n off Bit Patterns and Error TestsSend DS1 Pattern Off Send DS1 Line PatternSyntax send ds1 n line p2e11p2e15p2e23qrss Send DS1 Payload PatternAccess Navigator Payload Code Send DS1 Line Pattern with BER Test Example set ds1 9 line p2e15 test Syntax send ds1 n line p2e11p2e15p2e23qrss testFBE 26. Send DS1 Payload Pattern with BER Test Send DS1 Payload Pattern with BER TestExample send ds1 9 payload p2e15 test Test Example15-52 Other Maintenance Commands Load tftp config ipaddr file Show usersWhoami Show isdn database show crv database Technical SupportTrace eoc Off Trace tmc onLet run for 2 or 3 minutes Trace tmc off Trace eocMaintenance Procedures Maintenance Procedures Repair and Return ProcedureOverview Replace Controller CardTools and Materials Required Verify Equipment Status Determine Which Replacement Procedure to UseProcedure Summary PrecautionsReplace Protected Controller Card Verify Compatibility Remove Front Cover Location of Controller Cards Replace Standby ControllerInstalling and Removing Controller Card Verify Operation and Compatibility Replace Other Controller Card Replace Unprotected Controller Card Controller B Active DS1 Card Installed Access Navigator Release August 16-15 Insert New Controller Access Navigator Release August 16-17 Remove Old Controller Replace Quad T1 Framer Card OverviewQF Card Slot DS1 Circuit Numbers Tools and Materials Required Set clock2 ds1 n Verify Equipment StatusTemporarily Move Clock Sources if required Set clock1 ds1 nLocation of Front Panel Cover Screws 10. Location of Quad T1 Framer Cards Replace Quad T1 Card11. Installing Quad T1 Framer Card Verify Operation 12. Location of Front DS-1 Status Indicators Show clock Restore Clock Sources if requiredInstall Simm on Controller Card Precautions Tools and Materials Required 16-30 Standby Controller ACTIVE/STANDBY indicator is off 14. Location of Front Panel Cover Screws 15. Location of Controller Cards Install SimmSimm Access Navigator Release August 16-35 16-36 Update Controller Card Software Update Controller Card Software Download ProceduresUpdate Software via Tftp Two Controllers Tftp RequirementsEvent Log 17-4 Information and Materials Required Install Optional Tftp Server SoftwareRequirement One Controller is in Standby Status equipment allVerify IP Connectivity Upload ConfigurationDownload Software Show ds0 Set ds0 321 up set ds0 321 downSet ds0 321 down set ds0 321 up Example load tftp config 192.168.118.65 AN26 Download ConfigurationXmodem Requirements Update Software via Xmodem Two Controllers17-12 Access Navigator Release August 17-13 System Access Navigator Release August 17-15 17-16 Update Software via Xmodem One Controller 17-18 SW Build Number 17701 Boot Code Revision 01.09 Minutes Access Navigator Release August 17-21 17-22 CLI Language Reference CLI Language Reference CLI Access Via RS-232 and TelnetTerminal emulation Port settingsCLI Requirements CLI over RS-232Ethernet interface Access Navigator IP addressCLI over Telnet RS-232 interface for modem connectionUsing CLI Command Scripts Character and Line DelaysConfirmations and Errors SystemID set ds1 24 framing esf Command CategoriesCommands, Confirmations, and Error Messages CLI Conventions and ShortcutsText Conventions SystemID set ds1 42 framing esfSet ds1 1-4 up Command Syntax Descriptions Command Shortcuts Tabbing Entering DS1 and DS0 Numbers and RangesKeyboard Shortcuts Displaying Basic Commands Online HelpHelp System Overview Context Sensitive Help 18-12 Syntax print help Printing the Help FileUser Level Access Users and PasswordsAdministration Access LevelsSyntax show users Managing UsersWho Am Show UsersSet User Access Level Add UserSyntax add user name Example add user alice Delete User Set User PasswordDelete User Password Access DefinitionLogin with No User Name Required Logging In and OutStartup Message Login with User Name Required Login with No Password RequiredLogin with Password Required Example set autoexit Autoexit CLI Session TimeoutLogout Exit Syntax set autoexit minutesACO CLI Command ListCLI Language Reference Add Interface ACOType Description Remote Port Maximum Number of DS0sAlarms Syntax alarms majorminoralertSyntax add user name Syntax alarms equipment majorminoralert Syntax alarms ds1 nallSyntax alarms ds1 nall majorminoralert Syntax alarms equipmentClear DS1 Performance Clear Config LogClear Bert Log Clear Blocked Call CountClear Remote Log Clear LogClear Peak Call Count Clear Permanent Call CountExample connect 2519-24 Connect18-30 Drop Groom Switch Connect Remote InterfaceDrop Example delete interface AcmeV35 Delete InterfaceSyntax connect remote name fxrs232sdslt1dropv35 Syntax delete interface nameExample disconnect DisconnectSyntax delete user name Syntax disconnect nchSyntax disconnect remote name Disconnect RemoteExit Exit Remote Session Ctrl+CXmodem LoadActive Load Tftp Config Log Example load tftp config 192.168.118.65 AN26Example log equipment minor Example log MessageLog Bert Example log config ds0 Log ConfigDescription Example log configExample log tmc Message Log TMCLogon Remote Syntax logon remote nExample logon remote Ping Read Remote AlarmsSyntax read remote n alarms Example read remote 9 alarms18-46 Access Navigator Release August 18-47 Read Remote Connections Syntax read remote n connectionsExample read remote 9 connections Access Navigator Release August 18-49 Read Remote Log Syntax read remote n logExample read remote 9 log Syntax read remote n rs232 Read Remote LoopbackRead Remote RS232 Example read remote 9 loopbackSyntax read remote n t1t1drop performance Read Remote PerformanceAccess Navigator Release August 18-53 Syntax read remote n t1 Read Remote T1Read remote T1drop Read Remote T1dropLevel 3 monitor Read remoteRead Remote Syntax read remote nExample read remote 9 Syntax reset ds1 n Reset AllReset DS1 Framer Syntax reset allExample reset remote Reset RemoteReset Standby Syntax reset remote nParameter Default Comments Restore DefaultsDefault Settings Syntax restore defaultsNormal CLI Language Reference Line loopback deactivate Send DS1 CSU LoopupSend DS1 Line Loopup Example send ds1 9 csu loopupExample send ds1 9 csu loopdown 00001110 11111111 Send DS1 Line pattern Example send ds1 9 line loopupExample send ds1 9 line loopdown Send DS1 Line Pattern Example set ds1 9 line p2e15 Send DS1 Line pattern TestSend DS1 Line Pattern with BER Test Access Navigator Release August 18-69 Send DS1 Network Loopup Send DS1 Network LoopupSend DS1 NIU Loopup Example send ds1 9 network loopupExample send ds1 9 network loopdown Example send ds1 9 niu loopup Syntax send ds1 n niu loopup loopdownExample send ds1 9 niu loopdown Send DS1 Payload LoopupExample send ds1 9 payload loopdown Example send ds1 9 payload loopupSend DS1 Payload pattern 10. Send DS1 Payload Pattern Example send ds1 9 payload p2e15 Send DS1 Payload pattern Test11. Send DS1 Payload Pattern with BER Test P2e11 Example set ds1 9 payload p2e15 testExample send ds1 9 payload f1in8 test Example send remote 9 loopdown Send DS1 OffSend Remote Loopdown Example send ds1 9 offExample send remote 9 rs232 line loopup Send Remote RS232 Line LoopupSend Remote RS232 TSI Loopup Syntax send remote n rs232 tsi equipmentnetwork loopup Send Remote Sdsl Payload LoopupExample send remote 9 sdsl payload loopup Send Remote T1 Payload LoopupExample send remote 9 t1 payload loopup Send Remote T1 TSI LoopupExample send remote 9 t1 tsi loopup Remote loopdown commandExample send remote 9 t1drop line loopup Send Remote T1Drop Line LoopupSend Remote T1Drop Payload Loopup Example send remote 9 t1drop payload loopup Send Remote T1Drop TSI LoopupExample send remote 9 t1drop tsi loopup Send Remote V35 Line LoopupExample send remote 9 v35 line loopup 21. Remote V.35 Line LoopupSend Remote V35 TSI Loopup Send Switch Provision Request Syntax send switch provision requestSyntax send remote n v35 tsi equipmentnetwork loopup Set Alarms Example set alarms major onSet Autoexit Syntax set clock1clock2 setting Setting DescriptionSet Clock Set CRV Idle Set DateSet DS0 CRV Syntax set ds0 nch crv range slc96 513 crv Ds0 49-16 Crv 111-118Ds0 41-24 Crv 311-323 26. DS0s Assigned to CRVs in Odd-Even Order Syntax set ds0 nch isdn none Set DS0 Isdn BRI CRVSyntax set ds0 nch pphone Syntax set ds0 nch pphone none Set DS0 P-PhoneSet DS0 Service Syntax set ds0 nch updownExample set ds0 131-16 up Syntax set ds0 nch signal didemgsgshrgls Set DS0 SignalSet DS0 Type 27. Signaling Used in Common ApplicationsSet DS1 Clock Set DS1 FDLSyntax set ds0 nch type datavoicegr303 Framing Application Configuration RequirementsPermissible Selections ApplicationExample set ds1 9 framing esf Set DS1 FramingExample set ds1 12 fdl none Example set ds1 12 fdl t1403 Syntax set ds1 n framing d4esfslc96Set DS1 ID Set DS1 LBOSet DS1 Line Loopup Example set ds1 9 linecode b8zs Set DS1 LinecodeExample set ds1 9 line loopdown Syntax set ds1 n linecode amib8zsExample set ds1 9 loopdetect off Set DS1 LoopdetectSet DS1 Payload Loopup Syntax set ds1 n payload loopuploopdownExample set ds1 9 payload loopdown Mgmt caip Set DS1 Remote Device MgmtExample set ds1 Mgmt ds1Example set ds1 9 up Set DS1 ServiceSet DS1 TermID Syntax set ds1 n updownSet DS1 Threshold Syntax set ds1 n termid idExample set ds1 5 termid Syntax set ds1 n type dropgroomswitch Set DS1 TypeSet EOC Set Ethernet IP Address Syntax set eoc primarysecondary nchnoneSyntax set ethernet ip address address mask Set ID Set IP Gateway AddressExample set id Acme Corp. AN#2 Example set id DNVRCO1A201 Set Remote Config Syntax set ip gateway addressExample set ip gateway Example set ip gateway none Set Remote RS232 Baud Set Remote IDSet Remote RS232 Stop Set Remote RS232 DataSet Remote T1Drop Framing Syntax set remote n t1drop framing d4esfExample set remote 9 t1drop framing d4 Set Remote T1Drop Linecode Set Remote T1Drop LBOSet Remote V35 ClockInv Set Remote T1Drop PRMSet Remote V35 Data Set Remote V35 CTSSet Remote V35 DSU Set Remote V35 RxClockSet Remote V35 Speed Syntax set screen heightoff Set ScreenSyntax set remote n v35 speed Example set remote 9 v35 speed nx64Set Snmp GetCom Set Snmp ContactSet Snmp Name Set Snmp LocationSet Snmp SetCom Set Snmp NMS AddressSet Snmp TrapCom Set Switch TypeExample set time Set TimeSet TMC Syntax set time hhmmssSet User Level Syntax set user name level accessSyntax set user name password Syntax show autoexit Show AutoexitShow Clock Show ConnectExample show connect Syntax show connect nShow CRV Syntax show crv rangeExample show crv 30. Factory Default Call Reference Values Syntax show ds0 nch Show DateShow DS0 Syntax show dateShow DS1 Syntax show ds1 nExample show ds1 Access Navigator Release August 18-141 Remote Device Mgmt on Performance Description ThresholdsSyntax show ds1 all Show DS1 All18-144 Show EOC Show EthernetSyntax show ethernet Show Interface Show IDExample show interface AcmeT1 Example show interface all Syntax show interface nameallShow Isdn CRV Show IPExample show isdn crv Syntax show isdn crv rangeShow Remote Syntax show remote nallExample show remote Example show remote all Show Remote Connections Syntax show remote n connectionsExample show remote 9 connections 18-152 Syntax show snmp Show SnmpShow TMC Show SwitchSwitch Setting Description Show TimeAccess Navigator Release August 18-155 Status Clock Status CRV Status DS0 Status DS1 18-160 Status DS1 All Status DS1 Performance Access Navigator Release August 18-163 18-164 Status DS1 Performance History UAS Status EOC Syntax status equipment all Example status equipment Status EquipmentExample status equipment all Status IP Status Isdn CRV Status Remote Status TMC Pots Syntax status tmc allintervalrange Status TMC HistorySwitch Controller Upload Tftp ConfigSyntax switch controller WhoAmI Example upload tftp config 192.168.118.65 CAN2618-178 Appendix Remote Digital Customer Premises Terminal RDT EOC InterfaceAccess Navigator Release August Managed Object Class Support Alarm Count List Objects on page A-5Analog Line Termination Objects Alarm Count List ObjectsTable A-2 Alarm Count List Objects Attribute Support Command Support Create Get Set DeleteTable A-4 DS1 Framed Path Termination Objects DS0 Channel Termination ObjectsDS1 Framed Path Termination Objects Table A-3 DS0 Channel Termination ObjectsTable A-6 DS1 Line Termination Objects DS1 Line Termination ObjectsEBS Line Termination Objects Table A-5 DS1 Line Termination ObjectsTable A-8 Isdn Framed Path Termination Objects Isdn Line Termination ObjectsIsdn Framed Path Termination Objects Table A-7 Isdn Line Termination ObjectsIsdn Framed Path Termination Objects Table A-10 Crossconnection Quarter DS0 Channel TerminationCrossconnection Table A-9 Isdn Framed Path Termination ObjectsTable A-12 Idlc Call Processing Profile Objects Equipment ObjectsIdlc Call Processing Profile Objects Table A-11 Equipment ObjectsTable A-13 Idlc Data Link Profile Objects Idlc Data Link Profile ObjectsTable A-14 Idlc Data Link Termination Objects Idlc Data Link Termination ObjectsTable A-16 Memory Objects Idlc Terminal ObjectsMemory Objects Table A-15 Idlc Terminal ObjectsTable A-18 Protection Group Objects Network Element ObjectsProtection Group Objects Table A-17 Network Element ObjectsTable A-19 Protection Group Unit Objects Protection Group Unit ObjectsActions Table A-20 Action SupportManaged Object Class Action Support Notifications Table A-21 Event Report NotificationManaged Object Class Event Report Notification FDL Interface Figure B-1. FDL Interface FDL InterfaceAdit 600 TDM Remote Provisioning Requirements Access Navigator Remote Provisioning RequirementsAccess Bank II Remote Provisioning Requirements Remote Provisioning RequirementsRemote Provisioning Capabilities Access Bank II CapabilitiesAccess Bank II Capabilities Interface Capabilities and SettingsRTS FDL Interface Snmp Interface Operations Location Center Snmp InterfaceFigure C-2. Carrier Access Enterprise MIB top level Carrier Access Enterprise MIBMIB Structure Snmp BasicsMIB Tables Table C-1.Standard Snmp Object TypesObject Type Description Managing Networks Table C-2 Standard Snmp MessagesMessage Type Description Snmp Protocols Snmp Requirements Table C-3 Snmp Configuration ItemsTrap Description Test Method Snmp Trap ReportsTable C-4 Standard Snmp Trap Reports Table C-5 Enterprise Snmp Trap ReportsSnmp Interface Glossary LTE GlossaryLult Definitions Page Identifier Access Navigator Release August GlossaryGlossary-7 Electronic Business Set Or Service Access Navigator Release August GlossaryGlossary-9 Multiplex POP RAI Stratum Wide Area Network Wideband GlossaryGlossaryGlossaryGlossary-14 August Index EOC IndexAccess Navigator Release August Index CPE DLC LED FXO TMC LAN T1 TSI MIB Index PRI Sdsl DS1 CRV Isdn BRI CRV Phone Service Signal Type DSU SPR Tftp TSI Index Index