Manuals / Carrier Access / Computer Equipment / Network Router

Carrier Access Access Navigator user manual Mailtech-support@carrieraccess.com

Models: Access Navigator

1 704

Download 704 pages 57.28 Kb

Page 2

Copyright© 2003 Carrier Access Corporation. All rights reserved.

The information presented in this manual is subject to change without notice and does not represent a commitment on the part of Carrier Access Corporation. The hardware and software described herein are furnished under license(s) or non-disclosure agreement(s). The hardware, software, and manual may be used or copied only in accordance with the terms of such agreement(s), including, but not limited to, the software license contained herein. It is against the law to reproduce, transmit, transcribe, store in a retrieval system, or translate into any medium - electronic, mechanical, magnetic, optical, chemical, manual, or otherwise - any part of this manual or software supplied with the Access Navigator for any purpose other than the purchaser's personal use without the express written permission of Carrier Access Corporation.

Access Navigator, Access Bank, Adit, and the Carrier Access logo are registered trademarks of Carrier Access Corporation. Valet and NetworkValet are trademarks of Carrier Access Corporation. All other brand or product names are trademarks or registration trademarks of their respective companies or organizations.

Contact Information:

Carrier Access Corporation 5395 Pearl Parkway Boulder, CO 80301-2490 Corporate Phone: (800) 495-5455 Fax: (303) 443-5908 www.carrieraccess.com

Customer Support Direct: (800) 786-9929

E-mail:tech-support@carrieraccess.com

Image 2

Carrier Access Access Navigator user manual Mailtech-support@carrieraccess.com

Contents

Access Navigator Mailtech-support@carrieraccess.com Preface Compliance PrefaceElectrostatic Discharge ESD Precautions Title and Risk Carrier Access Software License AgreementLicense Term WarrantyCopyright DisclaimerJurisdiction and Venue Warranty Limitations of Warranty & Limitation of RemediesWarranty Product Returns Follow Electrostatic Discharge ESD Precautions onTable of Contents Access Navigator / GR-303 + Data Host Table of ContentsAccess Navigator / GR-303 Host with P-Phone Physical Installation Electrical Installation1xv 1xvi August Access Navigator Release Start Management Session Provision Access NavigatorProvision DCS Service Provision GR-303 Service Provision Remote Access BankProvision Remote Adit 600 via FDL Provision Remote Adit 600 via IP DS0Alarm Clearing Diagnostics & Troubleshooting1xxi Maintenance Procedures Update Controller Card SoftwareCLI Language Reference 1xxiv August Access Navigator Release 1xxv 1xxvi August Access Navigator Release EOC Interface Glossary FDL InterfaceSnmp Interface IndexChapter Overview IntroductionFeatures and Benefits Access Navigator ConfigurationsAccess Navigator System Architecture System ArchitectureAdit Carrier Access Support ProductsAccess Banks Command Line Interface ManagementSnmp Valet and NetworkValet EMS Software Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Access Navigator / DCS Service ManagerSwitch Center Co-location Customer Premises Facilities ServicesFunctions ManagementNetwork Configuration Quad T1 Framer Card Features Controller Card FeaturesInterfaces SpecificationsApplications DCS OperationSystem Clocking SignalingAlarms Management InterfacesEnvironmental PowerCompliance PhysicalPart 15, Class a Compliance RequirementsFCC Requirements PartUL Requirements Service Order Codes SOCTelcordia Bellcore Requirements Facility Interface Codes FICPart Number Description Ordering InformationCSA Requirements Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data HostGR-303 Ethernet RS-232 Modem Voice GR-303 Services Lines Management Key System DCS Services Access Navigator Data Host ArchitectureManagement Architecture IP DS0 ManagementAccess Navigator FDL Management Architecture FDL ManagementGR-303 call support Applications GR-303 Operation CrossconnectsGR-303 Signaling DCS SignalingCompliance Compliance Requirements Telcordia Bellcore Requirements Ordering Information Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-PhoneAccess Navigator / GR-303 with P-Phone Architecture Features and Benefits Voice Fax Phone Services P-Phone Service Support Using Adit 600 TerminalsDCS Services Management Architecture FDL Management Configuration Applications Specifications GR-303 Signaling Standards Compliance Requirements Telcordia Bellcore Requirements Ordering Information Ordering Information Physical Installation Compliance and Safety Requirements Physical InstallationTools and Materials Unpacking and InspectionHorizontal 19-Inch Rack Mount Installation SummaryPrecautions Tools and Materials Attach Mounting Brackets to Access Navigator Attach Access Navigator to Equipment RackMounting Four per side Bracket Fasten brackets to Horizontal 23-Inch Rack Mount Assemble Mounting Brackets Installation in 23-inch Equipment Rack Inches minimum Vertical Rack Mount Using Crossbars Install Crossbars Attach Access Navigator to CrossbarsCrossbar Installation Inch Equipment Rack Precautions Vertical Wall MountEnsure Adequate Clearance Prepare PlywoodAttach Access Navigator to Plywood Wall View Wire Tie Plywood Sheet Inches Minimum 12. Mounting Hole Pattern on Plywood 13. Wall Mount Bracket Installation Physical Installation Electrical Installation Electrical Installation Static-Sensitive Equipment Handling Procedures Tools and Materials Required Chassis Ground Connection Run Ground Wire to Access Navigator Connect Ground Wire to Ground LugAttach Ground Lug to Access Navigator DSX-1 Cable Connections Prepare DSX-1 Cables CAC Connect DSX-1 Cables to Access Navigator Location of Rear Panel DS1 ConnectorsElectrical Installation Attach Ferrite Beads Attaching Ferrite Bead RF SuppressorsConnect DSX-1 Cables to Interface or Patch Panel DSX-1 Cable Pin Connections and Flying Wire Colors Card GroupElectrical Installation RS-232 Management Connection Information, Tools, and MaterialsRS-232 DTE-to-DCE Cable Connect Shielded RS-232 Cable RS-232 DCE-to-DCE Modem Cable ConnectionsAttach Ferrite Bead RF Suppressor 10. Attaching Ferrite Bead RF SuppressorPreconfigure Optional Modem Make Ethernet Cable Optional Ethernet Management ConnectionInformation and Materials MDI Port Pins Signals Connect Ethernet Cable to Access Navigator Connect Ethernet Cable to Ethernet HubExternal Timing Source Bits Connection Make Bits Cable Optional Connect Bits CableAlarm Output Connections Wire Alarm Output Connector 15. Alarm Output ConnectorMaximum Plug Output Alarm Connector into Access Navigator 18. Location of Rear Panel Alarm Output ConnectorAlarm Input Connections Wire Alarm Input Connector 19. Alarm Input ConnectorCable Shield Plug Alarm Input Connector into Access Navigator 22. Location of Rear Panel Alarm Input ConnectorDC Power Connections Wire Power Connectors UsedVerify Wiring Connect Power Plugs to Access NavigatorDress Cables and Wires Dress Cables and WiresAcceptance Test Verification SummaryApply Power and Verify Operation 26. Location of Front Panel Power-On Status LEDsVerify Chassis Ground Connection Verify DSX-1 ConnectionsVerify RS-232 Management Connection Verify Ethernet Cable Connection Verify Ethernet Management ConnectionVerify Bits Connection Set clock1 bits set clock2 bitsVerify Alarm Output Connections Controller ’A’ Indicators Controller ’B’ IndicatorsElectrical Installation Verify Alarm Input Connections 31. Location of Rear Panel Alarm Input ConnectorExit Management Session ExitInstall Redundant Controller Card Verify Software Compatibility Remove Front Cover 33. Location of Front Panel Cover ScrewsInstall Controller Card 34. Location of Controller CardsSwitch controller Verify OperationReplace Front Cover Install Additional Quad T1 Framer Cards 37. Location of Front Panel Cover Screws Install Quad T1 Framer Card 38. Location of Quad T1 Framer CardsEject Status equipment Set ds1 n up29-32 13-16 17-20 21-24 26-28 Set ds1 n downReplace Front Cover Configure Management InterfacesSetup Summary Start RS-232 Management Session Set Date Set TimeSet System ID or Clli code Set IP Address and Subnet MaskSet Gateway Address Exit Management Session Start Management Session Management Requirements Start Management SessionCommand Line Interface Conventions Show ds1RS-232 Management Requirements Procedure SummaryRS-232 Management Obtain Information Connect RS-232 Cable to Access NavigatorSet Up Terminal Program Start RS-232 Management Session Perform Management Operations Exit RS-232 Management SessionTelnet Management Telnet Management RequirementsStart Telnet Program and Connect to Access Navigator Start Telnet Management SessionExit Telnet Management Session When Finished NetworkValet EMS and Valet Management Start Management Session Provision Access Navigator Basic Provisioning Overview Provision Access NavigatorCLI Commands Descriptions Basic Provisioning Quick GuideObtain Provisioning Information Verify System Equipment Configuration Set System ID or Clli Code Show idShow date Set DateSet Time Show timeSet Ethernet Properties Set ethernet ip address none Set User and Password Security Set user Alice password Set Snmp Properties DNVRCO1A201Example Set snmp nms 1 Provision DCS Service Provision DCS Service DCS Provisioning OverviewProvisioning Isdn BRI Service Provisioning TR-08 Service with DCSProvisioning Conventional TR-08 Voice Services Provisioning Voice Services for TR-08 Shelves B, C, and DProvisioning Enhanced Voice and Data Services Special TR-08 SettingsDCS Provisioning Quick Guide Card not installed Verify Service Status Show ds1 allStatus ds1 n Set Unused Circuits Out of Service Set ds1 n down Set ds0 nch type voicedataSet System Clock Source Provision Groom DS1 Circuits to Network CACExample Set ds1 10 loopdetect on Test Groom DS1 Circuits Provision Drop DS1 Circuits to SubscribersSet ds1 20 framing esf Provision and Connect Isdn PRI Channels Provision and Connect Isdn BRI 3DS0 ChannelsProvision and Connect DS0s DS0 #10 Set ds1 n up set ds0 nch up Turn Up ServiceTest DS1 and DS0 Circuits Test DS1 and DS0 Circuits Provision GR-303 Service Provision GR-303 Service GR-303 Provisioning OverviewAccess Navigator GR-303 Services Provisioning P-Phone Service Provisioning TR-08 Service with GR-303 Translation Provisioning TR-08 Service to Access BanksSpecial Pots Cards TR-08 ConfigurationSignaling Translation CRV NumberingSet ds0 49-16 crv Set ds0 41-24 crv 311-334 slc96Switch Shelf Access Bank I/TR-08 Loopback Code Response Framing and FDL SettingsAccess Bank I/TR-08 Switch Settings GR-303 Provisioning Quick Guide Set DS1s in service Connect Isdn D channel to SwitchSet DS0s in service Isdn BRI 41 TDM channelsAccess Navigator Release August 10-11 10-12 Set ds1 n down set ds0 nch down Set System Switch Type Show switchProvision Switch DS1s to Interface Group 10-16 Access Navigator Release August 10-17 Assign Primary and Secondary EOC Assign Primary and Secondary TMC Set tmc primary nchnoneTest DS1 Circuits Provision Drop DS1 Circuits to Subscriber Set ds1 n framing d4esfslc96 Example Set ds1 Fdl none Fdl t1403 10-24 Provision Isdn BRI 41 TDM Service to Subscribers CRV Send switch provision request Show isdn database10-28 Access Navigator Release August 10-29 Provision DS0s to Subscribers Set ds0 nch type gr303 Assign Call Reference Values CRVs Example Set ds0 21-4 crv Test Circuits Provision Remote Access Bank Remote Access Bank II Provisioning Overview Provision Remote Access BankPre-Provisioning and Testing RequirementsCrossconnect Features Analog InterfacesValid Crossconnect Assignments Crossconnections AbiiFX Interfaces Support Analog Voice and Data Services FX Analog InterfacesInterface Type DS1 Type DS0 Type Voice Data GR-303 Fractional InterfacesValid Interface Assignments Remote Interfaces Remote Access Bank II Provisioning Quick Guide Remote Access Bank II Maintenance Quick Guide DS1 Card Installed Card not installed 11-12 Access Navigator Release August 11-13 Temporarily Disable Configuration Downloading Provision Drop DS1 to Remote Access Bank Set ds1 n remote device management cafdl Provision DS0s Set ds0 nch type voicedatagr303 Provision DS0 Crossconnects Example connect 2519-24 Create Fractional Interfaces if required Configure Remote RS-232 Interface if used Set baud rate with the following command Configure Remote T1 Drop Interface if used Set remote n t1drop prm ansiatt Set remote n t1drop lbo settingSet remote n t1drop linecode amib8zs Configure Remote V.35 Interface if used Set remote n v35 clkinv rxtxrxtxnone Download Configuration to Remote Access Bank Connect Fractional Interface to Remote InterfaceVerify Downloaded Settings optional Test Remote Circuits Call Status FX and Spots To Loop orProvision Remote Adit 600 via FDL Remote Adit 600 FDL Provisioning Overview Provision Remote Adit 600 via FDLFDL Management Configuration On-Net Customer Location PremisesRemote Adit 600 FDL Provisioning Quick Guide Provision Remote Adit 600 via FDL SetVerify Equipment Configuration Access Navigator Release August 12-7 CA FDL Status remote nallInterface Provision Drop DS1s to Remote Adit Set ds1 n linecode amib8zs 12-12 Provision Drop DS0s Set ds0 nch signal lsgsem Set ds0 nch up Example set ds0 101-24 upProvision DS0 Crossconnects if required Crossconnect Examples Provision Remote Adit Logon remote n12-18 Provision Remote Adit 600 via IP DS0 Remote IP DS0 Provisioning Overview Provision Remote Adit 600 via IP DS0IP DS0 Management Configuration Carrier Access IP DS0 Management ConfigurationAccess Navigator CLI Commands Descriptions Remote IP DS0 Provisioning Quick GuideRouter Provisioning Quick Guide Adit CLI Commands DescriptionsRouter Setup Verify status of management channelSelect the PVC Management as Disabled Set Device Name to Adit1Remote Adit IP DS0 Provisioning Quick Guide 13-8 Access Navigator Release August 13-9 13-10 Out of Service Provision Groom DS1s to Adit Router Set ds1 32 framing esf 13-14 Access Navigator Release August 13-15 Set ds1 n framing d4esf Set ds1 n remote device management caip ipaddr pphoneSet DS1 identification Provision Groom DS0s to Adit Router Provision Drop DS0s to Remote Adit 13-20 Access Navigator Release August 13-21 13-22 Access Navigator Release August 13-23 13-24 Alarm Clearing Facility Alarm System go to Clear Alarms FDL on Identify Alarm Clearing ProcedureAlarm Clearing Event Message Description Trouble Clearing Procedure Clear Alarms FDLCLI Critical Alarm Message and Trouble Clearing Procedure Set alarms critical offCLI Major Alarm Message and Trouble Clearing Procedure Set ds1 n updownCLI Minor Alarm Message and Trouble Clearing Procedure Card Software onStatus eoc Show eocStatus tmc Show tmcClear Alarms EOC EOC Critical Alarm Message and Trouble Clearing ProcedureEOC Major Alarm Message and Trouble Clearing Procedure EOC Minor Alarm Message and Trouble Clearing Procedure Active 14-12 EOC Warning Alarm Message and Trouble Clearing Procedure SwitchTrap Message Description Trouble Clearing Procedure Clear Alarms SnmpTrap Message and Trouble Clearing Procedure Clear Alarms Status Indicators Alarm IndicatorsLED State Description Troubleshooting Power Status LEDsPower Status LEDs Active/Standby Controller Status LEDs Status equipment command forSystem, use the switch controller 10. Active/Standby Controller Status LEDs11. Critical Alarm Status LEDs Critical Alarm Status LEDsMajor Alarm Status LEDs 12. Major Alarm Status LEDs13. Minor Alarm Status LEDs Minor Alarm Status LEDsAlarm Cutoff ACO Status LED 14. Alarm Cutoff ACO Status LEDs15. DS1 Status LEDs Set ds1 up commandDS1 Status LEDs Ethernet Link Status LED 16. Ethernet Link Status LED14-22 Diagnostics & Troubleshooting Operations Interface Alarms and LogsDiagnostics & Troubleshooting Alarm and Status Indicators Alarm ReportingAlarm Testing Syntax set alarms criticalmajorminor onoffAlarm Signaling Red, Yellow RAI, Blue AIS Facility Alarm SystemAlarm Cutoff ACO Syntax log majorminoralertinfo DS1 FailuresEvent Log Configuration Change Log Syntax clear bert log Bert LogTMC Log Syntax log tmc permanentAlarm and Status Indicators Indicator LocationsRear Panel Ethernet Indicator State Description Indicator DescriptionsIndicator Descriptions GreenSyntax status clock Status and PerformanceStatus Clock Example status ds0 Status DS0Syntax status ds0 nch Field Description Status DS1Syntax status ds1 n Example status ds1Status DS1 All Syntax status ds1 allAccess Navigator Release August 15-15 Example status ds1 9 performance Status DS1 PerformanceSyntax status ds1 n performance Example status ds1 9 performance history Status DS1 Performance HistorySyntax status ds1 n performance history Clear DS1 Performance Syntax clear ds1 n performanceStatus Equipment Syntax status equipmentStatus IP Syntax status ipField Status RemoteSyntax status remote nall Example status remote allSyntax status crv range GR-303 Status and PerformanceStatus CRV Example status crvExample status isdn crv Status Isdn CRVSyntax status isdn crv range 15-24 Syntax status eoc Status EOCStatus TMC Syntax status tmcOriginating Calls Blocked Calls Secondary Example status tmc all Status TMC HistorySyntax status tmc allinterval Clear Permanent Call Count Clear Blocked Call CountClear Peak Call Count Set CRV IdleDS1 FDL Protocol Near-End LoopbacksDS1 Loopdetect Syntax set ds1 n loopdetect onoffSyntax set ds1 n line loopdownloopup DS1 Line LoopbackDS1 Payload Loopback Syntax set ds1 n payload loopdownloopupSyntax send ds1 n csu loopuploopdown Far-End LoopbacksDS1 CSU Loopup DS1 Line Loopup Syntax send ds1 n line loopuploopdownDS1 Network Loopup Syntax send ds1 n network loopuploopdownDS1 NIU Loopup Syntax send ds1 n niu loopuploopdownDS1 Payload Loopup Syntax send ds1 n payload loopuploopdownSend Remote Loopdown Access Bank II LoopbacksRead Remote Loopback Syntax read remote n loopbackSyntax send remote n rs232 line loopup Send Remote RS232 Line LoopupSend Remote RS232 TSI Equipment Loopup Syntax send remote 9 rs232 tsi equipment loopupSyntax send remote 9 rs232 tsi network loopup Send Remote RS232 TSI Network LoopupSend Remote Sdsl Payload Loopup Syntax send remote n sdsl payload loopupSyntax send remote n t1 payload loopup Send Remote T1 Payload LoopupSend Remote T1 TSI Loopup Syntax send remote n t1 tsi loopupSyntax send remote n t1drop line loopup Send Remote T1 Drop Line LoopupSend Remote T1 Drop Payload Loopup Syntax send remote n t1drop payload loopupSyntax send remote n v35 line loopup Send Remote V35 Line LoopupSyntax send remote n t1drop tsi loopup Syntax send remote n v35 tsi equipment loopup Send Remote V35 TSI Equipment LoopupSend Remote V35 TSI Network Loopup Syntax send remote n v35 tsi network loopupSend DS1 Line Pattern Bit Patterns and Error TestsSend DS1 Pattern Off Syntax send ds1 n offSend DS1 Payload Pattern Syntax send ds1 n line p2e11p2e15p2e23qrssAccess Navigator Payload Code Send DS1 Line Pattern with BER Test Syntax send ds1 n line p2e11p2e15p2e23qrss test Example set ds1 9 line p2e15 testFBE Send DS1 Payload Pattern with BER Test 26. Send DS1 Payload Pattern with BER TestExample send ds1 9 payload p2e15 test Example Test15-52 Other Maintenance Commands Whoami Load tftp config ipaddr fileShow users Technical Support Show isdn database show crv databaseTrace tmc off Trace eoc Trace tmc onLet run for 2 or 3 minutes Trace eoc OffMaintenance Procedures Repair and Return Procedure Maintenance ProceduresReplace Controller Card OverviewTools and Materials Required Determine Which Replacement Procedure to Use Verify Equipment StatusReplace Protected Controller Card Procedure SummaryPrecautions Verify Compatibility Remove Front Cover Replace Standby Controller Location of Controller CardsInstalling and Removing Controller Card Verify Operation and Compatibility Replace Other Controller Card Replace Unprotected Controller Card Controller B Active DS1 Card Installed Access Navigator Release August 16-15 Insert New Controller Access Navigator Release August 16-17 Remove Old Controller QF Card Slot DS1 Circuit Numbers Replace Quad T1 Framer CardOverview Tools and Materials Required Set clock1 ds1 n Verify Equipment StatusTemporarily Move Clock Sources if required Set clock2 ds1 nLocation of Front Panel Cover Screws Replace Quad T1 Card 10. Location of Quad T1 Framer Cards11. Installing Quad T1 Framer Card Verify Operation 12. Location of Front DS-1 Status Indicators Restore Clock Sources if required Show clockInstall Simm on Controller Card Precautions Tools and Materials Required 16-30 Standby Controller ACTIVE/STANDBY indicator is off 14. Location of Front Panel Cover Screws Install Simm 15. Location of Controller CardsSimm Access Navigator Release August 16-35 16-36 Update Controller Card Software Download Procedures Update Controller Card SoftwareEvent Log Update Software via Tftp Two ControllersTftp Requirements 17-4 Install Optional Tftp Server Software Information and Materials RequiredStatus equipment all Requirement One Controller is in StandbyUpload Configuration Verify IP ConnectivityDownload Software Set ds0 321 down set ds0 321 up Show ds0Set ds0 321 up set ds0 321 down Download Configuration Example load tftp config 192.168.118.65 AN26Update Software via Xmodem Two Controllers Xmodem Requirements17-12 Access Navigator Release August 17-13 System Access Navigator Release August 17-15 17-16 Update Software via Xmodem One Controller 17-18 SW Build Number 17701 Boot Code Revision 01.09 Minutes Access Navigator Release August 17-21 17-22 CLI Language Reference CLI Access Via RS-232 and Telnet CLI Language ReferenceCLI over RS-232 Port settingsCLI Requirements Terminal emulationRS-232 interface for modem connection Access Navigator IP addressCLI over Telnet Ethernet interfaceConfirmations and Errors Using CLI Command ScriptsCharacter and Line Delays CLI Conventions and Shortcuts Command CategoriesCommands, Confirmations, and Error Messages SystemID set ds1 24 framing esfSet ds1 1-4 up Text ConventionsSystemID set ds1 42 framing esf Command Syntax Descriptions Keyboard Shortcuts Command Shortcuts TabbingEntering DS1 and DS0 Numbers and Ranges Help System Overview Displaying Basic CommandsOnline Help Context Sensitive Help 18-12 Printing the Help File Syntax print helpAccess Levels Users and PasswordsAdministration User Level AccessShow Users Managing UsersWho Am Syntax show usersSyntax add user name Example add user alice Set User Access LevelAdd User Access Definition Set User PasswordDelete User Password Delete UserStartup Message Login with No User Name RequiredLogging In and Out Login with Password Required Login with User Name RequiredLogin with No Password Required Syntax set autoexit minutes Autoexit CLI Session TimeoutLogout Exit Example set autoexitCLI Command List ACOCLI Language Reference ACO Add InterfaceRemote Port Maximum Number of DS0s Type DescriptionSyntax add user name AlarmsSyntax alarms majorminoralert Syntax alarms equipment Syntax alarms ds1 nallSyntax alarms ds1 nall majorminoralert Syntax alarms equipment majorminoralertClear Blocked Call Count Clear Config LogClear Bert Log Clear DS1 PerformanceClear Permanent Call Count Clear LogClear Peak Call Count Clear Remote LogConnect Example connect 2519-2418-30 Drop Drop Groom SwitchConnect Remote Interface Syntax delete interface name Delete InterfaceSyntax connect remote name fxrs232sdslt1dropv35 Example delete interface AcmeV35Syntax disconnect nch DisconnectSyntax delete user name Example disconnectExit Remote Session Ctrl+C Disconnect RemoteExit Syntax disconnect remote nameLoad XmodemActive Load Tftp Config Example load tftp config 192.168.118.65 AN26 LogExample log Message Example log equipment minorLog Bert Log Config Example log config ds0Example log config DescriptionLog TMC Example log tmc MessageExample logon remote Logon RemoteSyntax logon remote n Example read remote 9 alarms Read Remote AlarmsSyntax read remote n alarms Ping18-46 Access Navigator Release August 18-47 Example read remote 9 connections Read Remote ConnectionsSyntax read remote n connections Access Navigator Release August 18-49 Example read remote 9 log Read Remote LogSyntax read remote n log Example read remote 9 loopback Read Remote LoopbackRead Remote RS232 Syntax read remote n rs232Read Remote Performance Syntax read remote n t1t1drop performanceAccess Navigator Release August 18-53 Read Remote T1 Syntax read remote n t1Read remote Read Remote T1dropLevel 3 monitor Read remote T1dropExample read remote 9 Read RemoteSyntax read remote n Syntax reset all Reset AllReset DS1 Framer Syntax reset ds1 nSyntax reset remote n Reset RemoteReset Standby Example reset remoteSyntax restore defaults Restore DefaultsDefault Settings Parameter Default CommentsNormal CLI Language Reference Send DS1 CSU Loopup Line loopback deactivateExample send ds1 9 csu loopdown Send DS1 Line LoopupExample send ds1 9 csu loopup 00001110 11111111 Example send ds1 9 line loopdown Send DS1 Line patternExample send ds1 9 line loopup Send DS1 Line Pattern Send DS1 Line pattern Test Example set ds1 9 line p2e15Send DS1 Line Pattern with BER Test Access Navigator Release August 18-69 Send DS1 Network Loopup Send DS1 Network LoopupExample send ds1 9 network loopdown Send DS1 NIU LoopupExample send ds1 9 network loopup Syntax send ds1 n niu loopup loopdown Example send ds1 9 niu loopupSend DS1 Payload Loopup Example send ds1 9 niu loopdownExample send ds1 9 payload loopup Example send ds1 9 payload loopdownSend DS1 Payload pattern 10. Send DS1 Payload Pattern Send DS1 Payload pattern Test Example send ds1 9 payload p2e1511. Send DS1 Payload Pattern with BER Test Example set ds1 9 payload p2e15 test P2e11Example send ds1 9 payload f1in8 test Example send ds1 9 off Send DS1 OffSend Remote Loopdown Example send remote 9 loopdownSend Remote RS232 Line Loopup Example send remote 9 rs232 line loopupSend Remote RS232 TSI Loopup Send Remote Sdsl Payload Loopup Syntax send remote n rs232 tsi equipmentnetwork loopupSend Remote T1 Payload Loopup Example send remote 9 sdsl payload loopupSend Remote T1 TSI Loopup Example send remote 9 t1 payload loopupRemote loopdown command Example send remote 9 t1 tsi loopupSend Remote T1Drop Line Loopup Example send remote 9 t1drop line loopupSend Remote T1Drop Payload Loopup Send Remote T1Drop TSI Loopup Example send remote 9 t1drop payload loopupSend Remote V35 Line Loopup Example send remote 9 t1drop tsi loopup21. Remote V.35 Line Loopup Example send remote 9 v35 line loopupSend Remote V35 TSI Loopup Syntax send remote n v35 tsi equipmentnetwork loopup Send Switch Provision RequestSyntax send switch provision request Set Autoexit Set AlarmsExample set alarms major on Set Clock Syntax set clock1clock2 settingSetting Description Set DS0 CRV Set CRV IdleSet Date Syntax set ds0 nch crv range slc96 Ds0 41-24 Crv 311-323 513 crvDs0 49-16 Crv 111-118 26. DS0s Assigned to CRVs in Odd-Even Order Set DS0 Isdn BRI CRV Syntax set ds0 nch isdn noneSet DS0 P-Phone Syntax set ds0 nch pphone Syntax set ds0 nch pphone noneExample set ds0 131-16 up Set DS0 ServiceSyntax set ds0 nch updown Set DS0 Signal Syntax set ds0 nch signal didemgsgshrgls27. Signaling Used in Common Applications Set DS0 TypeSyntax set ds0 nch type datavoicegr303 Set DS1 ClockSet DS1 FDL Application Application Configuration RequirementsPermissible Selections FramingSyntax set ds1 n framing d4esfslc96 Set DS1 FramingExample set ds1 12 fdl none Example set ds1 12 fdl t1403 Example set ds1 9 framing esfSet DS1 Line Loopup Set DS1 IDSet DS1 LBO Syntax set ds1 n linecode amib8zs Set DS1 LinecodeExample set ds1 9 line loopdown Example set ds1 9 linecode b8zsSet DS1 Loopdetect Example set ds1 9 loopdetect offExample set ds1 9 payload loopdown Set DS1 Payload LoopupSyntax set ds1 n payload loopuploopdown Mgmt ds1 Set DS1 Remote Device MgmtExample set ds1 Mgmt caipSyntax set ds1 n updown Set DS1 ServiceSet DS1 TermID Example set ds1 9 upExample set ds1 5 termid Set DS1 ThresholdSyntax set ds1 n termid id Set EOC Syntax set ds1 n type dropgroomswitchSet DS1 Type Syntax set ethernet ip address address mask Set Ethernet IP AddressSyntax set eoc primarysecondary nchnone Example set id Acme Corp. AN#2 Example set id DNVRCO1A201 Set IDSet IP Gateway Address Example set ip gateway Example set ip gateway none Set Remote ConfigSyntax set ip gateway address Set Remote ID Set Remote RS232 BaudSet Remote RS232 Data Set Remote RS232 StopExample set remote 9 t1drop framing d4 Set Remote T1Drop FramingSyntax set remote n t1drop framing d4esf Set Remote T1Drop LBO Set Remote T1Drop LinecodeSet Remote T1Drop PRM Set Remote V35 ClockInvSet Remote V35 CTS Set Remote V35 DataSet Remote V35 Speed Set Remote V35 DSUSet Remote V35 RxClock Example set remote 9 v35 speed nx64 Set ScreenSyntax set remote n v35 speed Syntax set screen heightoffSet Snmp Contact Set Snmp GetComSet Snmp Location Set Snmp NameSet Snmp NMS Address Set Snmp SetComSet Switch Type Set Snmp TrapComSyntax set time hhmmss Set TimeSet TMC Example set timeSyntax set user name level access Set User LevelSyntax set user name password Show Connect Show AutoexitShow Clock Syntax show autoexitSyntax show connect n Example show connectExample show crv Show CRVSyntax show crv range 30. Factory Default Call Reference Values Syntax show date Show DateShow DS0 Syntax show ds0 nchExample show ds1 Show DS1Syntax show ds1 n Access Navigator Release August 18-141 Performance Description Thresholds Remote Device Mgmt onShow DS1 All Syntax show ds1 all18-144 Syntax show ethernet Show EOCShow Ethernet Show ID Show InterfaceSyntax show interface nameall Example show interface AcmeT1 Example show interface allShow IP Show Isdn CRVSyntax show isdn crv range Example show isdn crvExample show remote Example show remote all Show RemoteSyntax show remote nall Example show remote 9 connections Show Remote ConnectionsSyntax show remote n connections 18-152 Show Snmp Syntax show snmpShow Time Show SwitchSwitch Setting Description Show TMCAccess Navigator Release August 18-155 Status Clock Status CRV Status DS0 Status DS1 18-160 Status DS1 All Status DS1 Performance Access Navigator Release August 18-163 18-164 Status DS1 Performance History UAS Status EOC Status Equipment Syntax status equipment all Example status equipmentExample status equipment all Status IP Status Isdn CRV Status Remote Status TMC Pots Status TMC History Syntax status tmc allintervalrangeSyntax switch controller Switch ControllerUpload Tftp Config Example upload tftp config 192.168.118.65 CAN26 WhoAmI18-178 Appendix EOC Interface Remote Digital Customer Premises Terminal RDTAccess Navigator Release August Alarm Count List Objects on page A-5 Managed Object Class SupportAttribute Support Command Support Create Get Set Delete Alarm Count List ObjectsTable A-2 Alarm Count List Objects Analog Line Termination ObjectsTable A-3 DS0 Channel Termination Objects DS0 Channel Termination ObjectsDS1 Framed Path Termination Objects Table A-4 DS1 Framed Path Termination ObjectsTable A-5 DS1 Line Termination Objects DS1 Line Termination ObjectsEBS Line Termination Objects Table A-6 DS1 Line Termination ObjectsTable A-7 Isdn Line Termination Objects Isdn Line Termination ObjectsIsdn Framed Path Termination Objects Table A-8 Isdn Framed Path Termination ObjectsIsdn Framed Path Termination Objects Table A-9 Isdn Framed Path Termination Objects Quarter DS0 Channel TerminationCrossconnection Table A-10 CrossconnectionTable A-11 Equipment Objects Equipment ObjectsIdlc Call Processing Profile Objects Table A-12 Idlc Call Processing Profile ObjectsIdlc Data Link Profile Objects Table A-13 Idlc Data Link Profile ObjectsIdlc Data Link Termination Objects Table A-14 Idlc Data Link Termination ObjectsTable A-15 Idlc Terminal Objects Idlc Terminal ObjectsMemory Objects Table A-16 Memory ObjectsTable A-17 Network Element Objects Network Element ObjectsProtection Group Objects Table A-18 Protection Group ObjectsProtection Group Unit Objects Table A-19 Protection Group Unit ObjectsManaged Object Class Action Support ActionsTable A-20 Action Support Managed Object Class Event Report Notification NotificationsTable A-21 Event Report Notification FDL Interface FDL Interface Figure B-1. FDL InterfaceRemote Provisioning Requirements Access Navigator Remote Provisioning RequirementsAccess Bank II Remote Provisioning Requirements Adit 600 TDM Remote Provisioning RequirementsInterface Capabilities and Settings Access Bank II CapabilitiesAccess Bank II Capabilities Remote Provisioning CapabilitiesRTS FDL Interface Snmp Interface Snmp Interface Operations Location CenterCarrier Access Enterprise MIB Figure C-2. Carrier Access Enterprise MIB top levelSnmp Basics MIB StructureObject Type Description MIB TablesTable C-1.Standard Snmp Object Types Message Type Description Managing NetworksTable C-2 Standard Snmp Messages Snmp Protocols Table C-3 Snmp Configuration Items Snmp RequirementsTable C-5 Enterprise Snmp Trap Reports Snmp Trap ReportsTable C-4 Standard Snmp Trap Reports Trap Description Test MethodSnmp Interface Glossary Glossary LTELult Definitions Page Identifier Access Navigator Release August GlossaryGlossary-7 Electronic Business Set Or Service Access Navigator Release August GlossaryGlossary-9 Multiplex POP RAI Stratum Wide Area Network Wideband GlossaryGlossaryGlossaryGlossary-14 August Index Index EOCAccess Navigator Release August Index CPE DLC LED FXO TMC LAN T1 TSI MIB Index PRI Sdsl DS1 CRV Isdn BRI CRV Phone Service Signal Type DSU SPR Tftp TSI Index Index