Carrier Access Access Navigator specification

Provision Remote Access Bank II

Remote Access Bank II Provisioning Quick Guide

Remote Access Bank II Provisioning Quick Guide

NOTE: Do not locally provision the Access Bank II if you are remotely provisioning it through the Access Navigator. Local changes made to the Access Bank II will not be recorded in the Access Navigator data base. Consequently, any local changes will be overwritten when the Access Navigator downloads configuration settings.

Related Commands			Access Bank II
			Provisioning Items
set remote <n> config off			Temporarily disable configuration
			downloading to remote Access Bank
			II.

set ds1 <n>	type drop		Provision DS1 service to remote,
set ds1 <n>	framing esf		including remote management
set ds1 <n>	linecode b8zs		interface.
set ds1 <n>	remote mgmt cafdl
set ds1 <n>	lbo <setting>
set ds1 <n>	loopdetect off
set ds1 <n>	id	<"name">
set remote <n>		id <"name">
set ds0 <n:ch>		type <setting>	Provision DS0 service to remote.
set ds0 <n:ch>		signaling <setting>
set ds0 <n:ch>		crv <setting>
set ds0 <n:ch>		up
connect <n:ch>		<n:ch>	Provision DCS crossconnects to
disconnect <n:ch>			remote.
read remote <n> connections			Read remote DS0 connections and
read remote <n> rs232			interface settings.
read remote <n> t1
read remote <n> t1drop			Note: SDSL interface port has no
read remote <n> v35			settings to read.
add interface <"name"> <n:ch>			Create fractional interface and assign
			DS0s to be used.
set remote <n> rs232 <setting>			Configure remote interface port to
set remote <n> t1drop <setting>			meet customer requirements.
set remote <n> v35 <setting>
connect remote <"name"> <port>			Connect fractional interface to remote
disconnect remote <"name">			interface port.
set remote <n> config on			Download configuration and
set ds1 <n> up			turn up service.

Access Navigator - Release 1.8

August 2003

11-9

Image 257

Carrier Access Access Navigator user manual Remote Access Bank II Provisioning Quick Guide

Contents

Access Navigator Mailtech-support@carrieraccess.com Preface Preface Compliance Electrostatic Discharge ESD Precautions Title and Risk Carrier Access Software License AgreementLicense Copyright WarrantyTerm Disclaimer Jurisdiction and Venue Limitations of Warranty & Limitation of Remedies Warranty Follow Electrostatic Discharge ESD Precautions on Warranty Product Returns Table of Contents Table of Contents Access Navigator / GR-303 + Data Host Access Navigator / GR-303 Host with P-Phone Electrical Installation Physical Installation 1xv 1xvi August Access Navigator Release Start Management Session Provision Access NavigatorProvision DCS Service Provision Remote Access Bank Provision GR-303 Service Provision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via FDL Diagnostics & Troubleshooting Alarm Clearing 1xxi Update Controller Card Software Maintenance Procedures CLI Language Reference 1xxiv August Access Navigator Release 1xxv 1xxvi August Access Navigator Release EOC Interface Snmp Interface FDL InterfaceGlossary Index Chapter Introduction Overview Access Navigator Configurations Features and Benefits System Architecture Access Navigator System Architecture Adit Carrier Access Support ProductsAccess Banks Management Command Line Interface Snmp Valet and NetworkValet EMS Software Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Access Navigator / DCS Service Manager Switch Center Co-location Customer Premises Functions ServicesFacilities Management Network Quad T1 Framer Card Features Controller Card Features Configuration Applications SpecificationsInterfaces DCS Operation Alarms SignalingSystem Clocking Management Interfaces Compliance PowerEnvironmental Physical FCC Requirements Compliance RequirementsPart 15, Class a Part Telcordia Bellcore Requirements Service Order Codes SOCUL Requirements Facility Interface Codes FIC Part Number Description Ordering InformationCSA Requirements Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host Access Navigator / GR-303 + Data Host GR-303 Ethernet RS-232 Modem Voice GR-303 Services Lines Management Key System Access Navigator Data Host Architecture DCS Services IP DS0 Management Management Architecture FDL Management Access Navigator FDL Management Architecture GR-303 call support Applications Crossconnects GR-303 Operation DCS Signaling GR-303 Signaling Compliance Compliance Requirements Telcordia Bellcore Requirements Ordering Information Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 Host with P-Phone Access Navigator / GR-303 with P-Phone Architecture Features and Benefits Voice Fax P-Phone Service Support Using Adit 600 Terminals Phone Services DCS Services Management Architecture FDL Management Configuration Applications Specifications GR-303 Signaling Standards Compliance Requirements Telcordia Bellcore Requirements Ordering Information Ordering Information Physical Installation Physical Installation Compliance and Safety Requirements Unpacking and Inspection Tools and Materials Horizontal 19-Inch Rack Mount Installation SummaryPrecautions Tools and Materials Attach Access Navigator to Equipment Rack Attach Mounting Brackets to Access Navigator Mounting Four per side Bracket Fasten brackets to Horizontal 23-Inch Rack Mount Assemble Mounting Brackets Installation in 23-inch Equipment Rack Inches minimum Vertical Rack Mount Using Crossbars Attach Access Navigator to Crossbars Install Crossbars Crossbar Installation Inch Equipment Rack Vertical Wall Mount Precautions Prepare Plywood Ensure Adequate Clearance Attach Access Navigator to Plywood Wall View Wire Tie Plywood Sheet Inches Minimum 12. Mounting Hole Pattern on Plywood 13. Wall Mount Bracket Installation Physical Installation Electrical Installation Electrical Installation Static-Sensitive Equipment Handling Procedures Tools and Materials Required Chassis Ground Connection Connect Ground Wire to Ground Lug Run Ground Wire to Access Navigator Attach Ground Lug to Access Navigator DSX-1 Cable Connections Prepare DSX-1 Cables CAC Location of Rear Panel DS1 Connectors Connect DSX-1 Cables to Access Navigator Electrical Installation Attaching Ferrite Bead RF Suppressors Attach Ferrite Beads Connect DSX-1 Cables to Interface or Patch Panel Card Group DSX-1 Cable Pin Connections and Flying Wire Colors Electrical Installation Information, Tools, and Materials RS-232 Management Connection RS-232 DTE-to-DCE Cable RS-232 DCE-to-DCE Modem Cable Connections Connect Shielded RS-232 Cable 10. Attaching Ferrite Bead RF Suppressor Attach Ferrite Bead RF Suppressor Preconfigure Optional Modem Make Ethernet Cable Optional Ethernet Management ConnectionInformation and Materials MDI Port Pins Signals Connect Ethernet Cable to Ethernet Hub Connect Ethernet Cable to Access Navigator External Timing Source Bits Connection Connect Bits Cable Make Bits Cable Optional Alarm Output Connections 15. Alarm Output Connector Wire Alarm Output Connector Maximum 18. Location of Rear Panel Alarm Output Connector Plug Output Alarm Connector into Access Navigator Alarm Input Connections 19. Alarm Input Connector Wire Alarm Input Connector Cable Shield 22. Location of Rear Panel Alarm Input Connector Plug Alarm Input Connector into Access Navigator DC Power Connections Used Wire Power Connectors Connect Power Plugs to Access Navigator Verify Wiring Dress Cables and Wires Dress Cables and Wires Verification Summary Acceptance Test 26. Location of Front Panel Power-On Status LEDs Apply Power and Verify Operation Verify DSX-1 Connections Verify Chassis Ground Connection Verify RS-232 Management Connection Verify Ethernet Management Connection Verify Ethernet Cable Connection Set clock1 bits set clock2 bits Verify Bits Connection Controller ’A’ Indicators Controller ’B’ Indicators Verify Alarm Output Connections Electrical Installation 31. Location of Rear Panel Alarm Input Connector Verify Alarm Input Connections Exit Exit Management Session Install Redundant Controller Card Verify Software Compatibility 33. Location of Front Panel Cover Screws Remove Front Cover 34. Location of Controller Cards Install Controller Card Verify Operation Switch controller Replace Front Cover Install Additional Quad T1 Framer Cards 37. Location of Front Panel Cover Screws 38. Location of Quad T1 Framer Cards Install Quad T1 Framer Card Eject Set ds1 n up Status equipment Set ds1 n down 29-32 13-16 17-20 21-24 26-28 Replace Front Cover Configure Management InterfacesSetup Summary Start RS-232 Management Session Set Time Set Date Set IP Address and Subnet Mask Set System ID or Clli code Set Gateway Address Exit Management Session Start Management Session Start Management Session Management Requirements Show ds1 Command Line Interface Conventions RS-232 Management Requirements Procedure SummaryRS-232 Management Obtain Information Connect RS-232 Cable to Access NavigatorSet Up Terminal Program Start RS-232 Management Session Exit RS-232 Management Session Perform Management Operations Telnet Management Requirements Telnet Management Start Telnet Management Session Start Telnet Program and Connect to Access Navigator Exit Telnet Management Session When Finished NetworkValet EMS and Valet Management Start Management Session Provision Access Navigator CLI Commands Descriptions Provision Access NavigatorBasic Provisioning Overview Basic Provisioning Quick Guide Obtain Provisioning Information Verify System Equipment Configuration Show id Set System ID or Clli Code Set Time Set DateShow date Show time Set Ethernet Properties Set ethernet ip address none Set User and Password Security Set user Alice password DNVRCO1A201 Set Snmp Properties Example Set snmp nms 1 Provision DCS Service DCS Provisioning Overview Provision DCS Service Provisioning TR-08 Service with DCS Provisioning Isdn BRI Service Provisioning Voice Services for TR-08 Shelves B, C, and D Provisioning Conventional TR-08 Voice Services Special TR-08 Settings Provisioning Enhanced Voice and Data Services DCS Provisioning Quick Guide Card not installed Show ds1 all Verify Service Status Status ds1 n Set ds1 n down Set ds0 nch type voicedata Set Unused Circuits Out of Service Set System Clock Source CAC Provision Groom DS1 Circuits to Network Example Set ds1 10 loopdetect on Provision Drop DS1 Circuits to Subscribers Test Groom DS1 Circuits Set ds1 20 framing esf Provision and Connect Isdn BRI 3DS0 Channels Provision and Connect Isdn PRI Channels Provision and Connect DS0s DS0 #10 Set ds1 n up set ds0 nch up Turn Up ServiceTest DS1 and DS0 Circuits Test DS1 and DS0 Circuits Provision GR-303 Service GR-303 Provisioning Overview Provision GR-303 Service Access Navigator GR-303 Services Provisioning P-Phone Service Provisioning TR-08 Service to Access Banks Provisioning TR-08 Service with GR-303 Translation Signaling Translation TR-08 ConfigurationSpecial Pots Cards CRV Numbering Set ds0 41-24 crv 311-334 slc96 Set ds0 49-16 crv Switch Shelf Access Bank I/TR-08 Loopback Code Response Framing and FDL SettingsAccess Bank I/TR-08 Switch Settings GR-303 Provisioning Quick Guide Set DS0s in service Connect Isdn D channel to SwitchSet DS1s in service Isdn BRI 41 TDM channels Access Navigator Release August 10-11 10-12 Set ds1 n down set ds0 nch down Show switch Set System Switch Type Provision Switch DS1s to Interface Group 10-16 Access Navigator Release August 10-17 Assign Primary and Secondary EOC Set tmc primary nchnone Assign Primary and Secondary TMC Test DS1 Circuits Provision Drop DS1 Circuits to Subscriber Set ds1 n framing d4esfslc96 Example Set ds1 Fdl none Fdl t1403 10-24 Provision Isdn BRI 41 TDM Service to Subscribers CRV Show isdn database Send switch provision request 10-28 Access Navigator Release August 10-29 Provision DS0s to Subscribers Set ds0 nch type gr303 Assign Call Reference Values CRVs Example Set ds0 21-4 crv Test Circuits Provision Remote Access Bank Provision Remote Access Bank Remote Access Bank II Provisioning Overview Requirements Pre-Provisioning and Testing Analog Interfaces Crossconnect Features Crossconnections Abii Valid Crossconnect Assignments FX Analog Interfaces FX Interfaces Support Analog Voice and Data Services Interface Type DS1 Type DS0 Type Voice Data GR-303 Fractional InterfacesValid Interface Assignments Remote Interfaces Remote Access Bank II Provisioning Quick Guide Remote Access Bank II Maintenance Quick Guide DS1 Card Installed Card not installed 11-12 Access Navigator Release August 11-13 Temporarily Disable Configuration Downloading Provision Drop DS1 to Remote Access Bank Set ds1 n remote device management cafdl Provision DS0s Set ds0 nch type voicedatagr303 Provision DS0 Crossconnects Example connect 2519-24 Create Fractional Interfaces if required Configure Remote RS-232 Interface if used Set baud rate with the following command Configure Remote T1 Drop Interface if used Set remote n t1drop prm ansiatt Set remote n t1drop lbo settingSet remote n t1drop linecode amib8zs Configure Remote V.35 Interface if used Set remote n v35 clkinv rxtxrxtxnone Connect Fractional Interface to Remote Interface Download Configuration to Remote Access Bank Verify Downloaded Settings optional Call Status FX and Spots To Loop or Test Remote Circuits Provision Remote Adit 600 via FDL Provision Remote Adit 600 via FDL Remote Adit 600 FDL Provisioning Overview On-Net Customer Location Premises FDL Management Configuration Remote Adit 600 FDL Provisioning Quick Guide Set Provision Remote Adit 600 via FDL Verify Equipment Configuration Access Navigator Release August 12-7 Status remote nall CA FDL Interface Provision Drop DS1s to Remote Adit Set ds1 n linecode amib8zs 12-12 Provision Drop DS0s Set ds0 nch up Example set ds0 101-24 up Set ds0 nch signal lsgsem Provision DS0 Crossconnects if required Crossconnect Examples Logon remote n Provision Remote Adit 12-18 Provision Remote Adit 600 via IP DS0 Provision Remote Adit 600 via IP DS0 Remote IP DS0 Provisioning Overview Carrier Access IP DS0 Management Configuration IP DS0 Management Configuration Remote IP DS0 Provisioning Quick Guide Access Navigator CLI Commands Descriptions Router Setup Adit CLI Commands DescriptionsRouter Provisioning Quick Guide Verify status of management channel Set Device Name to Adit1 Select the PVC Management as Disabled Remote Adit IP DS0 Provisioning Quick Guide 13-8 Access Navigator Release August 13-9 13-10 Out of Service Provision Groom DS1s to Adit Router Set ds1 32 framing esf 13-14 Access Navigator Release August 13-15 Set ds1 n remote device management caip ipaddr pphone Set ds1 n framing d4esf Set DS1 identification Provision Groom DS0s to Adit Router Provision Drop DS0s to Remote Adit 13-20 Access Navigator Release August 13-21 13-22 Access Navigator Release August 13-23 13-24 Alarm Clearing Facility Alarm System go to Clear Alarms FDL on Identify Alarm Clearing ProcedureAlarm Clearing CLI Critical Alarm Message and Trouble Clearing Procedure Clear Alarms FDLEvent Message Description Trouble Clearing Procedure Set alarms critical off Set ds1 n updown CLI Major Alarm Message and Trouble Clearing Procedure Card Software on CLI Minor Alarm Message and Trouble Clearing Procedure Show eoc Status eoc Show tmc Status tmc EOC Critical Alarm Message and Trouble Clearing Procedure Clear Alarms EOC EOC Major Alarm Message and Trouble Clearing Procedure EOC Minor Alarm Message and Trouble Clearing Procedure Active 14-12 Switch EOC Warning Alarm Message and Trouble Clearing Procedure Trap Message Description Trouble Clearing Procedure Clear Alarms SnmpTrap Message and Trouble Clearing Procedure Alarm Indicators Clear Alarms Status Indicators LED State Description Troubleshooting Power Status LEDsPower Status LEDs System, use the switch controller Status equipment command forActive/Standby Controller Status LEDs 10. Active/Standby Controller Status LEDs Major Alarm Status LEDs Critical Alarm Status LEDs11. Critical Alarm Status LEDs 12. Major Alarm Status LEDs Alarm Cutoff ACO Status LED Minor Alarm Status LEDs13. Minor Alarm Status LEDs 14. Alarm Cutoff ACO Status LEDs 15. DS1 Status LEDs Set ds1 up commandDS1 Status LEDs 16. Ethernet Link Status LED Ethernet Link Status LED 14-22 Diagnostics & Troubleshooting Operations Interface Alarms and LogsDiagnostics & Troubleshooting Alarm Testing Alarm ReportingAlarm and Status Indicators Syntax set alarms criticalmajorminor onoff Alarm Signaling Red, Yellow RAI, Blue AIS Facility Alarm SystemAlarm Cutoff ACO Syntax log majorminoralertinfo DS1 FailuresEvent Log Configuration Change Log TMC Log Bert LogSyntax clear bert log Syntax log tmc permanent Indicator Locations Alarm and Status Indicators Rear Panel Ethernet Indicator Indicator Descriptions Indicator DescriptionsState Description Green Syntax status clock Status and PerformanceStatus Clock Example status ds0 Status DS0Syntax status ds0 nch Syntax status ds1 n Status DS1Field Description Example status ds1 Syntax status ds1 all Status DS1 All Access Navigator Release August 15-15 Example status ds1 9 performance Status DS1 PerformanceSyntax status ds1 n performance Example status ds1 9 performance history Status DS1 Performance HistorySyntax status ds1 n performance history Syntax clear ds1 n performance Clear DS1 Performance Syntax status equipment Status Equipment Syntax status ip Status IP Syntax status remote nall Status RemoteField Example status remote all Status CRV GR-303 Status and PerformanceSyntax status crv range Example status crv Example status isdn crv Status Isdn CRVSyntax status isdn crv range 15-24 Status TMC Status EOCSyntax status eoc Syntax status tmc Originating Calls Blocked Calls Secondary Example status tmc all Status TMC HistorySyntax status tmc allinterval Clear Peak Call Count Clear Blocked Call CountClear Permanent Call Count Set CRV Idle DS1 Loopdetect Near-End LoopbacksDS1 FDL Protocol Syntax set ds1 n loopdetect onoff DS1 Payload Loopback DS1 Line LoopbackSyntax set ds1 n line loopdownloopup Syntax set ds1 n payload loopdownloopup Syntax send ds1 n csu loopuploopdown Far-End LoopbacksDS1 CSU Loopup Syntax send ds1 n line loopuploopdown DS1 Line Loopup Syntax send ds1 n network loopuploopdown DS1 Network Loopup Syntax send ds1 n niu loopuploopdown DS1 NIU Loopup Syntax send ds1 n payload loopuploopdown DS1 Payload Loopup Read Remote Loopback Access Bank II LoopbacksSend Remote Loopdown Syntax read remote n loopback Send Remote RS232 TSI Equipment Loopup Send Remote RS232 Line LoopupSyntax send remote n rs232 line loopup Syntax send remote 9 rs232 tsi equipment loopup Send Remote Sdsl Payload Loopup Send Remote RS232 TSI Network LoopupSyntax send remote 9 rs232 tsi network loopup Syntax send remote n sdsl payload loopup Send Remote T1 TSI Loopup Send Remote T1 Payload LoopupSyntax send remote n t1 payload loopup Syntax send remote n t1 tsi loopup Send Remote T1 Drop Payload Loopup Send Remote T1 Drop Line LoopupSyntax send remote n t1drop line loopup Syntax send remote n t1drop payload loopup Syntax send remote n v35 line loopup Send Remote V35 Line LoopupSyntax send remote n t1drop tsi loopup Send Remote V35 TSI Network Loopup Send Remote V35 TSI Equipment LoopupSyntax send remote n v35 tsi equipment loopup Syntax send remote n v35 tsi network loopup Send DS1 Pattern Off Bit Patterns and Error TestsSend DS1 Line Pattern Syntax send ds1 n off Syntax send ds1 n line p2e11p2e15p2e23qrss Send DS1 Payload Pattern Access Navigator Payload Code Send DS1 Line Pattern with BER Test Example set ds1 9 line p2e15 test Syntax send ds1 n line p2e11p2e15p2e23qrss test FBE 26. Send DS1 Payload Pattern with BER Test Send DS1 Payload Pattern with BER Test Example send ds1 9 payload p2e15 test Test Example 15-52 Other Maintenance Commands Whoami Load tftp config ipaddr fileShow users Show isdn database show crv database Technical Support Let run for 2 or 3 minutes Trace tmc onTrace tmc off Trace eoc Trace eoc Off Maintenance Procedures Maintenance Procedures Repair and Return Procedure Overview Replace Controller Card Tools and Materials Required Verify Equipment Status Determine Which Replacement Procedure to Use Replace Protected Controller Card Procedure SummaryPrecautions Verify Compatibility Remove Front Cover Location of Controller Cards Replace Standby Controller Installing and Removing Controller Card Verify Operation and Compatibility Replace Other Controller Card Replace Unprotected Controller Card Controller B Active DS1 Card Installed Access Navigator Release August 16-15 Insert New Controller Access Navigator Release August 16-17 Remove Old Controller QF Card Slot DS1 Circuit Numbers Replace Quad T1 Framer CardOverview Tools and Materials Required Temporarily Move Clock Sources if required Verify Equipment StatusSet clock1 ds1 n Set clock2 ds1 n Location of Front Panel Cover Screws 10. Location of Quad T1 Framer Cards Replace Quad T1 Card 11. Installing Quad T1 Framer Card Verify Operation 12. Location of Front DS-1 Status Indicators Show clock Restore Clock Sources if required Install Simm on Controller Card Precautions Tools and Materials Required 16-30 Standby Controller ACTIVE/STANDBY indicator is off 14. Location of Front Panel Cover Screws 15. Location of Controller Cards Install Simm Simm Access Navigator Release August 16-35 16-36 Update Controller Card Software Update Controller Card Software Download Procedures Event Log Update Software via Tftp Two ControllersTftp Requirements 17-4 Information and Materials Required Install Optional Tftp Server Software Requirement One Controller is in Standby Status equipment all Verify IP Connectivity Upload Configuration Download Software Set ds0 321 down set ds0 321 up Show ds0Set ds0 321 up set ds0 321 down Example load tftp config 192.168.118.65 AN26 Download Configuration Xmodem Requirements Update Software via Xmodem Two Controllers 17-12 Access Navigator Release August 17-13 System Access Navigator Release August 17-15 17-16 Update Software via Xmodem One Controller 17-18 SW Build Number 17701 Boot Code Revision 01.09 Minutes Access Navigator Release August 17-21 17-22 CLI Language Reference CLI Language Reference CLI Access Via RS-232 and Telnet CLI Requirements Port settingsCLI over RS-232 Terminal emulation CLI over Telnet Access Navigator IP addressRS-232 interface for modem connection Ethernet interface Confirmations and Errors Using CLI Command ScriptsCharacter and Line Delays Commands, Confirmations, and Error Messages Command CategoriesCLI Conventions and Shortcuts SystemID set ds1 24 framing esf Set ds1 1-4 up Text ConventionsSystemID set ds1 42 framing esf Command Syntax Descriptions Keyboard Shortcuts Command Shortcuts TabbingEntering DS1 and DS0 Numbers and Ranges Help System Overview Displaying Basic CommandsOnline Help Context Sensitive Help 18-12 Syntax print help Printing the Help File Administration Users and PasswordsAccess Levels User Level Access Who Am Managing UsersShow Users Syntax show users Syntax add user name Example add user alice Set User Access LevelAdd User Delete User Password Set User PasswordAccess Definition Delete User Startup Message Login with No User Name RequiredLogging In and Out Login with Password Required Login with User Name RequiredLogin with No Password Required Logout Exit Autoexit CLI Session TimeoutSyntax set autoexit minutes Example set autoexit ACO CLI Command List CLI Language Reference Add Interface ACO Type Description Remote Port Maximum Number of DS0s Syntax add user name AlarmsSyntax alarms majorminoralert Syntax alarms ds1 nall majorminoralert Syntax alarms ds1 nallSyntax alarms equipment Syntax alarms equipment majorminoralert Clear Bert Log Clear Config LogClear Blocked Call Count Clear DS1 Performance Clear Peak Call Count Clear LogClear Permanent Call Count Clear Remote Log Example connect 2519-24 Connect 18-30 Drop Drop Groom SwitchConnect Remote Interface Syntax connect remote name fxrs232sdslt1dropv35 Delete InterfaceSyntax delete interface name Example delete interface AcmeV35 Syntax delete user name DisconnectSyntax disconnect nch Example disconnect Exit Disconnect RemoteExit Remote Session Ctrl+C Syntax disconnect remote name Xmodem Load Active Load Tftp Config Log Example load tftp config 192.168.118.65 AN26 Example log equipment minor Example log Message Log Bert Example log config ds0 Log Config Description Example log config Example log tmc Message Log TMC Example logon remote Logon RemoteSyntax logon remote n Syntax read remote n alarms Read Remote AlarmsExample read remote 9 alarms Ping 18-46 Access Navigator Release August 18-47 Example read remote 9 connections Read Remote ConnectionsSyntax read remote n connections Access Navigator Release August 18-49 Example read remote 9 log Read Remote LogSyntax read remote n log Read Remote RS232 Read Remote LoopbackExample read remote 9 loopback Syntax read remote n rs232 Syntax read remote n t1t1drop performance Read Remote Performance Access Navigator Release August 18-53 Syntax read remote n t1 Read Remote T1 Level 3 monitor Read Remote T1dropRead remote Read remote T1drop Example read remote 9 Read RemoteSyntax read remote n Reset DS1 Framer Reset AllSyntax reset all Syntax reset ds1 n Reset Standby Reset RemoteSyntax reset remote n Example reset remote Default Settings Restore DefaultsSyntax restore defaults Parameter Default Comments Normal CLI Language Reference Line loopback deactivate Send DS1 CSU Loopup Example send ds1 9 csu loopdown Send DS1 Line LoopupExample send ds1 9 csu loopup 00001110 11111111 Example send ds1 9 line loopdown Send DS1 Line patternExample send ds1 9 line loopup Send DS1 Line Pattern Example set ds1 9 line p2e15 Send DS1 Line pattern Test Send DS1 Line Pattern with BER Test Access Navigator Release August 18-69 Send DS1 Network Loopup Send DS1 Network Loopup Example send ds1 9 network loopdown Send DS1 NIU LoopupExample send ds1 9 network loopup Example send ds1 9 niu loopup Syntax send ds1 n niu loopup loopdown Example send ds1 9 niu loopdown Send DS1 Payload Loopup Example send ds1 9 payload loopdown Example send ds1 9 payload loopup Send DS1 Payload pattern 10. Send DS1 Payload Pattern Example send ds1 9 payload p2e15 Send DS1 Payload pattern Test 11. Send DS1 Payload Pattern with BER Test P2e11 Example set ds1 9 payload p2e15 test Example send ds1 9 payload f1in8 test Send Remote Loopdown Send DS1 OffExample send ds1 9 off Example send remote 9 loopdown Example send remote 9 rs232 line loopup Send Remote RS232 Line Loopup Send Remote RS232 TSI Loopup Syntax send remote n rs232 tsi equipmentnetwork loopup Send Remote Sdsl Payload Loopup Example send remote 9 sdsl payload loopup Send Remote T1 Payload Loopup Example send remote 9 t1 payload loopup Send Remote T1 TSI Loopup Example send remote 9 t1 tsi loopup Remote loopdown command Example send remote 9 t1drop line loopup Send Remote T1Drop Line Loopup Send Remote T1Drop Payload Loopup Example send remote 9 t1drop payload loopup Send Remote T1Drop TSI Loopup Example send remote 9 t1drop tsi loopup Send Remote V35 Line Loopup Example send remote 9 v35 line loopup 21. Remote V.35 Line Loopup Send Remote V35 TSI Loopup Syntax send remote n v35 tsi equipmentnetwork loopup Send Switch Provision RequestSyntax send switch provision request Set Autoexit Set AlarmsExample set alarms major on Set Clock Syntax set clock1clock2 settingSetting Description Set DS0 CRV Set CRV IdleSet Date Syntax set ds0 nch crv range slc96 Ds0 41-24 Crv 311-323 513 crvDs0 49-16 Crv 111-118 26. DS0s Assigned to CRVs in Odd-Even Order Syntax set ds0 nch isdn none Set DS0 Isdn BRI CRV Syntax set ds0 nch pphone Syntax set ds0 nch pphone none Set DS0 P-Phone Example set ds0 131-16 up Set DS0 ServiceSyntax set ds0 nch updown Syntax set ds0 nch signal didemgsgshrgls Set DS0 Signal Set DS0 Type 27. Signaling Used in Common Applications Syntax set ds0 nch type datavoicegr303 Set DS1 ClockSet DS1 FDL Permissible Selections Application Configuration RequirementsApplication Framing Example set ds1 12 fdl none Example set ds1 12 fdl t1403 Set DS1 FramingSyntax set ds1 n framing d4esfslc96 Example set ds1 9 framing esf Set DS1 Line Loopup Set DS1 IDSet DS1 LBO Example set ds1 9 line loopdown Set DS1 LinecodeSyntax set ds1 n linecode amib8zs Example set ds1 9 linecode b8zs Example set ds1 9 loopdetect off Set DS1 Loopdetect Example set ds1 9 payload loopdown Set DS1 Payload LoopupSyntax set ds1 n payload loopuploopdown Example set ds1 Set DS1 Remote Device MgmtMgmt ds1 Mgmt caip Set DS1 TermID Set DS1 ServiceSyntax set ds1 n updown Example set ds1 9 up Example set ds1 5 termid Set DS1 ThresholdSyntax set ds1 n termid id Set EOC Syntax set ds1 n type dropgroomswitchSet DS1 Type Syntax set ethernet ip address address mask Set Ethernet IP AddressSyntax set eoc primarysecondary nchnone Example set id Acme Corp. AN#2 Example set id DNVRCO1A201 Set IDSet IP Gateway Address Example set ip gateway Example set ip gateway none Set Remote ConfigSyntax set ip gateway address Set Remote RS232 Baud Set Remote ID Set Remote RS232 Stop Set Remote RS232 Data Example set remote 9 t1drop framing d4 Set Remote T1Drop FramingSyntax set remote n t1drop framing d4esf Set Remote T1Drop Linecode Set Remote T1Drop LBO Set Remote V35 ClockInv Set Remote T1Drop PRM Set Remote V35 Data Set Remote V35 CTS Set Remote V35 Speed Set Remote V35 DSUSet Remote V35 RxClock Syntax set remote n v35 speed Set ScreenExample set remote 9 v35 speed nx64 Syntax set screen heightoff Set Snmp GetCom Set Snmp Contact Set Snmp Name Set Snmp Location Set Snmp SetCom Set Snmp NMS Address Set Snmp TrapCom Set Switch Type Set TMC Set TimeSyntax set time hhmmss Example set time Set User Level Syntax set user name level access Syntax set user name password Show Clock Show AutoexitShow Connect Syntax show autoexit Example show connect Syntax show connect n Example show crv Show CRVSyntax show crv range 30. Factory Default Call Reference Values Show DS0 Show DateSyntax show date Syntax show ds0 nch Example show ds1 Show DS1Syntax show ds1 n Access Navigator Release August 18-141 Remote Device Mgmt on Performance Description Thresholds Syntax show ds1 all Show DS1 All 18-144 Syntax show ethernet Show EOCShow Ethernet Show Interface Show ID Example show interface AcmeT1 Example show interface all Syntax show interface nameall Show Isdn CRV Show IP Example show isdn crv Syntax show isdn crv range Example show remote Example show remote all Show RemoteSyntax show remote nall Example show remote 9 connections Show Remote ConnectionsSyntax show remote n connections 18-152 Syntax show snmp Show Snmp Switch Setting Description Show SwitchShow Time Show TMC Access Navigator Release August 18-155 Status Clock Status CRV Status DS0 Status DS1 18-160 Status DS1 All Status DS1 Performance Access Navigator Release August 18-163 18-164 Status DS1 Performance History UAS Status EOC Syntax status equipment all Example status equipment Status Equipment Example status equipment all Status IP Status Isdn CRV Status Remote Status TMC Pots Syntax status tmc allintervalrange Status TMC History Syntax switch controller Switch ControllerUpload Tftp Config WhoAmI Example upload tftp config 192.168.118.65 CAN26 18-178 Appendix Remote Digital Customer Premises Terminal RDT EOC Interface Access Navigator Release August Managed Object Class Support Alarm Count List Objects on page A-5 Table A-2 Alarm Count List Objects Alarm Count List ObjectsAttribute Support Command Support Create Get Set Delete Analog Line Termination Objects DS1 Framed Path Termination Objects DS0 Channel Termination ObjectsTable A-3 DS0 Channel Termination Objects Table A-4 DS1 Framed Path Termination Objects EBS Line Termination Objects DS1 Line Termination ObjectsTable A-5 DS1 Line Termination Objects Table A-6 DS1 Line Termination Objects Isdn Framed Path Termination Objects Isdn Line Termination ObjectsTable A-7 Isdn Line Termination Objects Table A-8 Isdn Framed Path Termination Objects Isdn Framed Path Termination Objects Crossconnection Quarter DS0 Channel TerminationTable A-9 Isdn Framed Path Termination Objects Table A-10 Crossconnection Idlc Call Processing Profile Objects Equipment ObjectsTable A-11 Equipment Objects Table A-12 Idlc Call Processing Profile Objects Table A-13 Idlc Data Link Profile Objects Idlc Data Link Profile Objects Table A-14 Idlc Data Link Termination Objects Idlc Data Link Termination Objects Memory Objects Idlc Terminal ObjectsTable A-15 Idlc Terminal Objects Table A-16 Memory Objects Protection Group Objects Network Element ObjectsTable A-17 Network Element Objects Table A-18 Protection Group Objects Table A-19 Protection Group Unit Objects Protection Group Unit Objects Managed Object Class Action Support ActionsTable A-20 Action Support Managed Object Class Event Report Notification NotificationsTable A-21 Event Report Notification FDL Interface Figure B-1. FDL Interface FDL Interface Access Bank II Remote Provisioning Requirements Access Navigator Remote Provisioning RequirementsRemote Provisioning Requirements Adit 600 TDM Remote Provisioning Requirements Access Bank II Capabilities Access Bank II CapabilitiesInterface Capabilities and Settings Remote Provisioning Capabilities RTS FDL Interface Snmp Interface Operations Location Center Snmp Interface Figure C-2. Carrier Access Enterprise MIB top level Carrier Access Enterprise MIB MIB Structure Snmp Basics Object Type Description MIB TablesTable C-1.Standard Snmp Object Types Message Type Description Managing NetworksTable C-2 Standard Snmp Messages Snmp Protocols Snmp Requirements Table C-3 Snmp Configuration Items Table C-4 Standard Snmp Trap Reports Snmp Trap ReportsTable C-5 Enterprise Snmp Trap Reports Trap Description Test Method Snmp Interface Glossary LTE Glossary Lult Definitions Page Identifier Access Navigator Release August GlossaryGlossary-7 Electronic Business Set Or Service Access Navigator Release August GlossaryGlossary-9 Multiplex POP RAI Stratum Wide Area Network Wideband GlossaryGlossaryGlossaryGlossary-14 August Index EOC Index Access Navigator Release August Index CPE DLC LED FXO TMC LAN T1 TSI MIB Index PRI Sdsl DS1 CRV Isdn BRI CRV Phone Service Signal Type DSU SPR Tftp TSI Index Index