Mitsubishi Electronics GOT1000 2.7 MELSEC-WS

2.7 MELSEC-WS

The device ranges that can be set when selecting [MELSEC-WS] as the controller type are as follows.

	Device	Setting range			Device No.
					representation
	Input (I)	I1.1	to	I12.8
device	Output (Q)	Q1.1	to	Q12.8	Decimal
	Logic result (LQ)	LQ0.0	to	LQ3.7	+Decimal
	Logic input (LI)	LI0.0	to	LI3.7
Bit
	Word device bit	Specified bit of the			-
		following word devices
	Data (byte)(D)	D0	to	D99	Decimal
	Data (word)(W)	W0	to	W49
device					Decimal
	EFI input (byte)(EI)	EI110	to	EI233	+Decimal
					+Decimal
Word
	EFI output (byte)(EQ)	EQ10	to	EQ22	Decimal
					+Decimal
	Logic input (byte)(LD)	LD0	to	LD3	Decimal
	Logic input (word)(LW)	LW0	to	LW1	Decimal

POINT

(1)Devices of MELSEC-WS

Only reading is possible for all devices.

(2)Device settings of MELSEC-WS

• Input(I), Output(Q)

	Input position(1 to 8)
Device
name	Module number(1 to 12)

• Logic result(LQ), Logic input(LI)

(3)Engineering software for MELSEC-WS and device representation of GT Designer3

The engineering software for MELSEC-WS and the device representation of GT Designer3 are different. Set the device by referring to the following table.

Device	GT Designer3			Engineering software for
						MELSEC-WS
	I	.						[		].I
I*1					: I/O model name
	(1-12(Dec)): Module number					(such as XTIO)
	(1-8): Input position		(1-12(Dec)): Module number
			(1-8): Input position
			[							].Q
Q*1	Q	.			: I/O model name
	(1-12(Dec)): Module number					(such as XTIO)
	(1-8): Output position		(1-12(Dec)): Module number
			(1-8): Output position
	LQ .		.
			: "Result"
LQ*1	(0-3): Byte number
			(0-3): Byte number
	(0-7): Bit position
			(0-7): Bit position
	LI .								[0] . .
LI*1					: CPU type (CPU0, CPU1)
	(0-3): Byte number
			(0-3): Byte number
	(0-7): Bit position
			(0-7): Bit position
	EI						[0].EFI			: , Byte
					: CPU type (CPU0, CPU1)
EI*1	(1-2): EFI number
			(1-2): EFI number
	(1-3): Device number
			(1-3): Device number
	(0-3): Byte number
			(0-3): Byte number
	EQ						[0].EFI			:1, Byte
EQ*1					: CPU type (CPU0, CPU1)
	(1-2): EFI number
			(1-2): EFI number
	(0-2): Byte number
			(0-2): Byte number
D	D						RS232 data
	(0-99(Dec)): Byte number		(Safety controller to RS232)
	W
	(0-49(Dec)): Word number

Device name

• EFI input(EI)

Device name

Bit position(0 to 7)

Byte number(0 to 3)

Byte number(0 to 3) Device number(1 to 3) EFI number(1 to 2)

W	Word virtualization of D	GOT independent device
	device	(Not available)
	W0= (D1(Upper bits),
	D0(Lower bits))
LD	LD	RS232 data
	(0-3): Byte number	(Safety controller to RS232)
	LW
	(0-1): Word number	GOT independent device
LW	Word virtualization of LD
	device	(Not available)
	LW0= (LD1(Upper bits),
	LD0(Lower bits))

• EFI output(EQ)

Device	Byte number(0 to 2)
name	EFI number(1 to 3)

*1 When the mapping position is changed by the MELSEC-WS engineering software, a mismatch occurs between virtual devices on GOT and MELSEC-WS mapping devices. When mapping is changed, use D devices or LD devices.

2 - 14	2. DEVICE RANGE THAT CAN BE SET
	2.7 MELSEC-WS