Mitsubishi Electronics GOT1000 9.4 PLC Side Settings, module, Switch setting of, MELSECNET/H network, 9.4.1System configuration

9.4 PLC Side Settings

This section describes the settings of the GOT and MELSECNET/H network module in the case of system configuration shown as 9.4.1.

When connecting the MELSECNET/H network module to the MELSECNET/H network system, specify the MELSECNET/H Mode or the MELSECNET/H Extended Mode as a network type.

POINT

MELSECNET/H network module

For details of the MELSECNET/H network module, refer to the following manual.

Q corresponding MELSECNET/H Network System Reference Manual (PLC to PLC network)

9.4.1System configuration

9.4.4 [Controller Setting] of GT Designer3

<GOT>

9

9.4.2							Switch setting of											MELSECNET/H CONNECTION(PLC PLCTONETWORK)
							MELSECNET/H network
							module											10
Set the station number setting switch and mode setting
																		MELSECNET/10 CONNECTION(PLC NETWORK)PLCTO
ERR.	L ERR.								ERR.	L ERR.
switch.
QJ71LP21, QJ71LP21-25								QJ71LP21S-25
QJ71LP21-25								QJ71LP21S-25	RUN	MNG
RUN	MNG
T.PASS	D.LINK							EXT.PW	T.PASS	D.LINK
SD	RD								SD	RD								11
X10	091				65				X10	091			3		65
STATION NO.		2	3	4					STATION NO.		2			4
		8	7				(1)				8		7				(1)	CONTROLLERIELink-CC NETWORK CONNECTION
	1	2	34							1	2		34
					5										5
X1	0								X1	0
	9		7		6					9			7		6
		8									8
IN									IN
	2	34	5				(2)	+24V		2	3	456					(2)	12
				67				EXT..PW							7
MODE	01				8				MODE	01					8
	E				A	9				E					A	9
	F	DCB								F	DCB

(Use the default value for settings other than the following.)

	Network type	: MNET/H Mode
	Network No.	: 1
	Station No.	: 2
	Made Setting	: Online (auto,reconnection)
		2	: LB0100H to LB01FFH
	Network range assignment *
MELSECNET/H (PLC to PLC network)			LW0100H to LW01FFH
		: 10Mbps
	Transmission speed

<MELSECNET/H network module> *1

(Use the default value for settings other than the following.)

Station No.	: 1
Mode	: Online (10Mbps)
Network type	: MNET/H mode (Control station)
Network No.	: 1
Total stations	: 2

Network range assignment *2: LB0000H to LB00FFH

LW0000H to LW00FFH

9.4.2Switch setting of MELSECNET/H network module

(1) [Network parameter] of GX Developer

*1 The MELSECNET/H network module is mounted at slot 0 of the base unit.

The start I/O No. of the MELSECNET/H network module is set at "0".

*2 The network type must be set according to the number of assignment of send points for each station.

When the number of assignment is 2000 bytes or less: MELSECNET/H mode

When the number of assignment is 2000 bytes or more: MELSECNET/H Extended Mode

POINT

When connecting to Q170MCPU

When connected to Q170MCPU, the start I/O No. of the MELSECNET/H network module is set to "70".

OUT

QJ71LP21 -25

QJ71BR11

QJ71BR11

RUN	MNG
T.PASS	D.LINK
SD	RD
ERR.	L ERR.
STATION NO.		2	34
X10	1
					5
	0
	9	8	7		6
X1	1	2	34
	0				5
	9	8	7		6
	2	3	4	56
					7
MODE	01				8
	F				A	9
	E
		DCB

QJ71BR11

24G

OUT

(FG)24G

QJ71LP21 S-25

(1)

(2)

CC-Link IE FIELD NETWORK CONNECTION

13

CC-Link CONNECTION (INTELLIGENT DEVICE STATION)

14

CC-Link CONNECTION (Via G4)

15

CONNECTION

INVERTER

16

CONNECTION

SERVO AMPLIFIER

9. MELSECNET/H CONNECTION (PLC TO PLC NETWORK)	9 - 11
9.4 PLC Side Settings