Parameter setting (when connecting to C Controller module)
Use
(1) Connection settings
|
| Setting |
Item | Set value | necessity at |
|
| GOT connection |
Target module*1 | 192.168.3.3 (Default) |
|
Write authority | Mark the checkbox |
|
|
|
|
User name*2 | target |
|
Password*2 | password |
|
Detailed settings | - |
|
|
|
|
: Necessary 
: As necessary 
: Not necessary
*1 If the IP address of the C Controller module has been changed, input the changed IP address or host name.
*2 If the account of the C Controller module has been changed, input the changed user name and password.
(2)MELSECNET/H Utility's [Parameter Settings]
(a)Parameter settings
|
| Setting |
Item | Set value | necessity at |
|
| GOT connection |
Number of modules | 1 |
|
|
|
|
Link device refresh cycle | (Use default value) |
|
|
|
|
Routing parameter | Refer to (b). |
|
|
|
|
Target module | 1 |
|
|
|
|
Start I/O No. | 0000H |
|
|
|
|
Channel No. | (Use default value) |
|
|
|
|
|
|
|
|
|
|
|
|
|
| Setting |
|
| Item |
|
|
|
| Set value | necessity at | ||
|
|
|
|
|
| GOT | ||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
| connection |
| Network type |
|
|
|
| MNET/10 mode |
| |||
settings |
|
|
|
| (Control station) |
| ||||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
Network No.*1 |
|
|
|
| 1 |
| ||||
|
|
|
|
|
| |||||
Operation | Group No. |
|
|
|
|
|
| 0 |
| |
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
| Mode |
|
|
|
|
|
|
| Online |
|
|
|
|
|
|
|
|
|
|
|
|
| Return |
|
|
|
|
|
|
| (Use default value) |
|
|
|
|
|
|
|
|
|
|
| |
Refresh parameters |
|
|
|
| (Use default value) |
| ||||
|
|
|
|
|
|
|
|
|
| |
| Total stations |
|
|
|
| 2 |
| |||
|
|
|
|
|
| |||||
| Assignment method |
|
| Start/End |
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
| for | LB |
| Sta. |
| Start |
| 0000H |
|
|
|
|
|
|
|
|
| |||
assignmentrangeNetwork | settingsLB/LW | rangeSendforrangeSend | stationeachLWstationeach |
| No.1 |
| End |
| 00FFH |
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
| *2 |
|
|
| Sta. |
| Start |
| 0100H |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| No.2 |
| End |
| 01FFH |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Sta. |
| Start |
| 0000H |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| No.1 |
| End |
| 00FFH |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Sta. |
| Start |
| 0100H |
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| No.2 |
| End |
| 01FFH |
|
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
| (LX/LY) settings*2 |
|
| No setting |
| |||||
| Monitoring time |
|
|
|
| (Use default value) |
| |||
|
|
|
|
| ||||||
| Specify I/O master Sta.*2 |
| No setting |
| ||||||
| Specify reserved Sta. |
|
| No setting |
| |||||
|
|
|
|
|
| |||||
| Supplementary settings |
|
| (Use default value) |
| |||||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| : Necessary | : As necessary : Not necessary | ||||
*1 Specify the same network No. as that of the GOT.
*2 Be sure to set the setting to perform the cyclic transmission.
POINT
When changing the network parameter
After writing the network parameter to the C Controller module, either turn the C Controller module OFF and then ON or reset it.
9
TO CONNECTIONPLC MELSECNET/H(PLCNETWORK)
10
MELSECNET/10 CONNECTION (PLC TO PLC NETWORK)
11
12
13
14
15
CONNECTION
INVERTER
16
CONNECTION
SERVO AMPLIFIER
10. MELSECNET/10 CONNECTION (PLC TO PLC NETWORK) | 10 - 15 |
10.4 PLC Side Setting |
|