(3) Operation setting DIP switch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Setting

 

Operation setting

Setting

Description

Set value

necessity

 

 

 

DIP switch

Switch

at GOT

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connection

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW1 = OFF

 

 

 

 

 

 

 

 

 

 

 

 

 

SW1,

Operation

SW6 = ON

 

 

 

 

 

 

 

 

 

 

 

 

 

SW6

mode

(fixed)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(Q mode)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW2

Peripheral

 

 

SW

 

transmissi

OFF (fixed)

 

SW3

 

1 2 3 4 5 6 7 8

ON

on speed*1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW5

Not used

OFF (fixed)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW7

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SW8

Test mode

OFF (fixed)

 

 

 

 

 

 

 

 

 

 

 

 

 

(Online mode)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

: Necessary : As necessary : Not necessary

*1 The peripheral connection module operates with the baud rate set in the GOT.

14.5.6 [Controller Setting] of GT Designer3

POINT

Operation mode of peripheral connection module

Be sure to set the "Q mode" as an operation mode of the peripheral connection module.

14.5.2Connecting AJ65BT-R2N

This section describes the settings of the GOT and peripheral connection module in the following case of the system configuration.

POINT

(1)Peripheral connection module

For details of the peripheral connection module, refer to the following manual.

Peripheral Connection Module Type AJ65BT- R2N User's Manual

(2)CC-Link module

For details of the CC-Link module, refer to the following manual.

CC-Link System Master/Local Module User's Manual QJ61BT11N

(3)CC-Link built-in CPU

For details on the CC-Link function built-in CPU, refer to the following manual.

MELSEC-L CC-Link System Master/Local

Module User's Manual

System configuration

14.5.3 Switch setting of CC-Link module (Q series)

14.5.4 [Network parameter] of GX Developer

<CC-Link module> *1 Setting example

Station type

: Master station

Station No.

: Station No. 0

Mode

: Remote net (Ver.1 mode)

All connect count

: 1

Transmission speed

: 156kbps

14.5.6 [Controller Setting] of GT Designer3

<GOT> Setting example Transmission speed: 9600bps

<AJ65BT-R2N> Setting example

Station type

: Intelligent device station

Station No.

: Station No. 1

Number of stations occupied

: Exclusive station 1

Transmission speed

: 156kbps

Switch setting of peripheral connection module

*1 The Start I/O No. of the CC-Link module is set to "0"

14 - 12

14. CC-Link CONNECTION (Via G4)

 

14.5 PLC Side Settings