Mitsubishi Electronics GOT1000 8.2 System Configuration, 8.2.1Connection to Ethernet module

8.2 System Configuration

8.2.1Connection to Ethernet module

When connecting to MELSEC-Q, QS, QnA, A or motion controller

PLC CPU	Ethernet	Communication driver
	module	GOT
	Connection cable	Ethernet(MELSEC),Q17nNC,CRnD-700

	PLC		Connection cable*1	Maximum	GOT		Number of
Model name	Ethernet module	Communication	Cable model	segment	Option device	Model	connectable
	*4*5	type		length*3			equipment
MELSEC-Q						*2
(Q mode)	QJ71E71-100				- (Built into GOT)	*8*9
MELSEC-QS	QJ71E71-B5	Ethernet		100m
	QJ71E71-B2
Motion controller	QJ71E71				GT15-J71E71-100
CPU (Q Series)*6
	AJ71QE71N3-T
	AJ71QE71N-B5					*2
	AJ71QE71N-B2				- (Built into GOT)	*8
	AJ71QE71N-T
	AJ71QE71N-B5T
	AJ71QE71
MELSEC-QnA	AJ71QE71-B5	Ethernet		100m
	A1SJ71QE71N3-T		Twisted pair cable
	A1SJ71QE71N-B5
			• 10BASE-T
	A1SJ71QE71N-B2
			Shielded twisted pair
	A1SJ71QE71N-T				GT15-J71E71-100
			cable (STP) or unshielded
	A1SJ71QE71N-B5T						128 GOTs*7
			twisted pair cable (UTP):
	A1SJ71QE71-B5						(recommended to
			Category 3, 4, and 5
	A1SJ71QE71-B2
							16 units or less)
			• 100BASE-TX
	AJ71E71N3-T		Shielded twisted pair
	AJ71E71N-B5		cable (STP):			*2
	AJ71E71N-B2		Category 5 and 5e		- (Built into GOT)	*8
MELSEC-A	AJ71E71N-T
	AJ71E71N-B5T
MELSEC-Q	AJ71E71-S3
(A mode)	A1SJ71E71N3-T	Ethernet		100m
	A1SJ71E71N-B5
Motion controller	A1SJ71E71N-B2
CPU (A Series)	A1SJ71E71N-T				GT15-J71E71-100
	A1SJ71E71N-B5T
	A1SJ71E71-B5-S3
	A1SJ71E71-B2-S3
						*2
MELSEC-L	LJ71E71-100	Ethernet		100m	- (Built into GOT)	*8
					GT15-J71E71-100

*1 The destination connected with the twisted pair cable varies with the configuration of the applicable Ethernet network system. Connect to the Ethernet module, hub, transceiver, or other system equipment corresponding to the applicable Ethernet network system.

Use cables, connectors, and hubs that meet the IEEE802.3 10BASE-T/100BASE-TX standard. A cross cable is available for connecting the GOT to the Ethernet module.

*2 When connecting GT16 of the function version A to an equipment that meets the 10BASE (-T/2/5) standard, use the switching hub and operate in a 10Mbps/100Mbps mixed environment.

For how to check the function version, refer to the following. GT16 User's Manual (Hardware)

1

PREPARATORYFORPROCEDURESMONITORING 2

RANGESETBE

DEVICE CANTHAT 3

RANGEACCESS MONITORINGFOR 4

MONITORTOREDUNTANTSYSTEM HOW 5

CONNECTIONBUS 6

DIRECTTOCONNECTIONCPU 7

LINKCOMPUTER CONNECTION 8

ETHERNETCONNECTION

8. ETHERNET CONNECTION	8 - 7
8.2 System Configuration